Search NASA⌕ Search

SEARCH · Search NASA

Results for “ED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Investigation of Chemical Species in the Corrosion Barrier Layer on Thermal CO 2 Treated AZ91D Magnesium Alloy with Lithium Nitrate

A unique corrosion barrier layer, formed by thermal CO 2 treatment with LiNO 3 on AZ91D, was characterized to reveal the chemical species and their spatial distribution using the combination of scanning transmission electron microscopy (STEM), energy dispersive spectroscopy (EDS), and electron energy loss spectroscopy (EELS) techniques. Two distinct and spatially segregated phases were identified as Li compound(s) with MgCO 3 and MgO in the surface barrier layer. Finally, based on the characterization results, it is presumed that the reaction of Mg oxide/hydroxide with LiNO 3 and CO 2 occurred preferentially in some local areas where Li compound(s) with MgCO 3 were present, but the unreacted areas contained MgO in the surface barrier layer.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elemental segregation to lattice defects in the CrMnFeCoNi high-entropy alloy during high temperature exposures

The influence of small plastic pre-strains on the elevated-temperature stability and microstructure of the equiatomic CrMnFeCoNi FCC solid solution is investigated. Particular attention is given to whether any of the alloy elements segregate to individual dislocations. To that end, CrMnFeCoNi samples were first deformed in tension at room temperature to plastic strains of 0.2 and 2.3%, and subsequently annealed at 973 K for 800 hours. The pre-strains activated planar slip of 1/2<110>-type dislocations on {111}-type glide planes. Interactions of this planar slip with special Σ3 grain boundaries formed a large number of dislocation segments with a <110>-type crystallographic orientation suitable for a credible end-on analysis of dislocation cores in HR-STEM. The cores of the 1/2<110> dislocations pushed up against the investigated grain boundaries were found to be close to the compact configuration. Within the sensitivity of the Super-X EDS mapping, no concentration gradient was detected near dislocations that would indicate enrichment at dislocation cores of any of the elemental constituents of the alloy after the pre-deformation and annealing. However, a Cr-rich tetragonal sigma phase nucleated and grew at grain boundary triple junctions during this anneal, processes that were not accelerated by the enhanced dislocation density present after pre-strain. A clear chromium gradient was observed in the Cr-depleted zones near grain boundaries suggesting that Cr transport occurred by relatively slow diffusion from the bulk to the grain boundaries and then by relatively fast diffusion along the grain boundaries to the precipitates. Accompanying the Cr depletion near grain boundaries is a simultaneous Ni and Mn enrichment, which promotes formation of the L1 0 NiMn phase that is observed on the grain boundaries after prolonged annealing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A data science approach for analysis and reconstruction of spinodal-like composition fields in irradiated FeCrAl alloys

A statistical method for the analysis of continuously distributed data representative of composition fluctuations in irradiated FeCrAl alloys acquired using Energy Dispersive X-ray Spectroscopy (EDS) method is presented. Using probability distribution functions, direct and cross-covariances between the elemental compositions, the effects of alloy composition and irradiation dose were investigated on the spatial distribution and length scale of composition fluctuations at the nanoscale. We have observed that, for neutron-irradiated FeCrAl alloys, the distribution of Fe and Cr followed a left-skewed and right-skewed distribution, respectively for all (average) alloy compositions and irradiation doses. The analysis also revealed enhanced spatial gradients in the elemental compositions at higher irradiation dose. Direct and cross-covariance estimates of the experimental data were also utilized for reconstruction of composition data through fitting it to a parametric form of the covariance functions. Linear Model of Coregionalization was used to determine the parameters of the covariance functions. Subsequently, a spectral method was utilized for simulating a realization of the alloy compositions. Close correspondence was observed between the experimental and the reconstructed data which was analyzed using probability distribution functions and covariance functions. Composition space of the experimental and reconstructed data and dislocation velocities as a function of applied stress and line directions over the entire composition maps were also examined.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A thermochemical database from high-throughput first-principles calculations and its application to analyzing phase evolution in AM-fabricated IN718

A comprehensive thermochemical database is constructed based on high–throughput first-principles phonon calculations of over 3000 atomic structures in limited concentrations in Ni, Fe, and Co alloys involving a total of 26 elements including Al, B, C, Cr, Cu, Hf, La, Mn, Mo, N, Nb, O, P, Re, Ru, S, Si, Ta, Ti, V, W, Y, and Zr, providing thermochemical data largely unavailable from existing experiments. Here, the database can be employed to predict the equilibrium phase compositions and fractions directly from first-principles by minimizing the chemical potential of a multicomponent system with a fixed overall chemical composition and a fixed temperature. It is applied to the additively manufactured nickel-based IN718 superalloy to analyze the phase evolution with temperature. IN718 is known for its great performance in tensile, fatigue, creep, and rupture strength, combined with easy fabrication and corrosion resistance. In particular, we successfully predicted the formation of L1 0 -FeNi, γ’-Ni 3 (Fe,Al), α-Cr, δ-Ni 3 (Nb,Mo), γ”-Ni 3 Nb, and η-Ni 3 Ti at low temperatures (below 680 K), γ’-Ni 3 Al, δ-Ni 3 Nb, γ”-Ni 3 Nb, α-Cr, and γ-Ni(Fe,Cr,Mo) at intermediate temperatures (between 680 and 1140 K), and δ-Ni 3 Nb and γ-Ni(Fe,Cr,Mo) at high temperatures (above 1140 K) in IN718. These predictions are validated by EDS mapping of compositional distributions and corresponding identifications of phase distributions. The database is expected to be a valuable source for future thermodynamic analysis and microstructure prediction of alloys involving the 26 elements.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Oxidation kinetic modelling of Fe-based oxygen carriers for chemical looping applications: Impact of the topochemical effect

Chemical looping is a promising technology for fossil fuel utilization due to its high fuel conversion efficiency with in-situ CO 2 capture capability. Metal oxide are used as oxygen carriers (OCs) and circulate between a fuel reactor and an air reactor to perform reduction and oxidation reactions, respectively. In general, OC exiting the fuel reactor is not reduced fully to its metallic state due to many factors including carbon deposition and OC deactivation. Therefore, the effect of the initial reduction state on the OC oxidation in the air reactor is a significant parameter for consideration in developing the oxidation kinetic model. The objective of this work is to develop a physically significant kinetic model that applies to the oxidation of both initially fully and partially reduced OC with air. For this study, 1.5 mm Fe-based OC particle supported with TiO 2 was used as the model OC particle due to its complex multistep reaction nature. The oxidation kinetics were experimentally investigated in a thermogravimetric analyzer (TGA). Results indicate a significant difference in the oxidation rate profile for the OCs when oxidized from an initially fully reduced compared to an initially partially reduced state. Elemental mapping via energy-dispersive X-ray spectroscopy (EDS) reveals a shrinking-core type topochemical pattern across the OC particle, which was identified to be the cause of the dependency of kinetics on the initial reduction state. A generalized kinetic model was developed based on the observed shrinking-core behavior without presuming any rate-determining steps and experimentally validated over a broad range of temperatures (800–1000 °C) and oxygen concentrations (5, 7, 10, and 15 mol%). Impacts of particle porosity, size, and core-shell structure on the OC oxidation kinetics were analyzed in the developed oxidation kinetic model to suggest methods of improving the oxidation rate of the OC without modifying the chemical composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Power System Operational Impacts of Electric Vehicle Dynamic Wireless Charging

The electrification of the transportation sector poses an opportunity for reducing greenhouse gas (GHG) emissions from passenger vehicles. Electric vehicle (EV) charging through dynamic wireless power transfer (DWPT), known as roadway electrification, could shift EV demand profiles to better coincide with renewable electricity generation. However, this would be a very large new load and few studies evaluate the regional impacts of DWPT charging in a power transmission system. This paper defines methods that address dataset generation for passenger vehicle trips and models to evaluate regional impacts for this emerging technology. Household vehicle miles traveled (VMT) data form localized EV demand profiles through discrete-event simulation. This data serves as exogenous inputs for a Production Cost Model (PCM) of a synthetic transmission system based on the Electric Reliability Council of Texas's (ERCOT) network. EV charging methods are compared for both a 2018 baseline generation mixture and a high-renewable generation case incorporating 20 GW of installed solar photovoltaic (PV) capacity. The PCM employs unit commitment and economic dispatch (UC&ED) models to compare financial, environmental, and grid reliability impacts from EV charging across passenger EV adoption levels. In-transit charging could reduce grid operational costs by as much as 1.49%, with up to $13.7B saved in annual vehicle operational costs for consumers compared to gas-powered vehicles. Health impacts analysis from power plant and vehicle tailpipe emissions from this study show net health benefits increase by 40% for in-transit charging coupled with high renewable generation. Renewable resources provide an avenue for cost-effective in-transit charging with reduced emissions. The combination of dataset generation and open-source power system modeling establish a foundation for the holistic evaluation of regional DWPT impacts.

dynamic wireless power transfer↗
DOE OSTI2021

Colloidal metal transport in soils developing on historic coal mine spoil

Chemical weathering of pyrite via oxidative dissolution is well-known for generating Fe(III)-bearing colloids at acid mine drainage (AMD) sites; however, the potential for physical weathering of pyrite-bearing materials and subsequent release and transport of colloidal pyrite and associated trace metals has not been studied. Here, we monitored the colloidal metal transport in soil developing on abandoned coal mine spoil with a history of AMD generation to systematically study the contribution of colloids to base and trace metal transport and determine the elemental and mineralogical composition of colloids. Additionally, we collected soil pore water using lysimeters with a pore size of approximately 1.3 μm and centrifugation was used to separate the colloids from aqueous fractions. Metal concentrations of Na, Ca, Mg, K, Si, Al, Mn, Fe, Cu, and Zn were analyzed. Our results show only 14% of the total Al and Cu were present in colloidal fractions whereas 23%, 43%, and 54% of Fe, Mn, and Zn were transported in the colloidal phase, respectively. In contrast, all base metals were primarily present in the aqueous concentration with a small fraction (<10%) present in the colloidal phase. The colloidal fractions of the base metals were inferred to be associated with the concentration of clay colloids. The release of colloids exhibited possible sensitivity toward weather conditions such as alternating high temperatures and rainfall during summer (May–July) compared to fall (August–November). The morphology, elemental, and mineral composition of colloids were determined by a scanning electron microscopy equipped with energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction (XRD). Colloids were dominated by phyllosilicates (biotite, muscovite, and kaolinite) with minor quartz and feldspars. Other minerals phases identified in colloidal fractions were hematite, goethite, arsenopyrite, and chalcopyrite. Colloids consisting of Fe, S, and O with structures resembling framboidal pyrite were identified, which is consistent with the non-silicates minerals identified by XRD. Our study suggests that the physical weathering of pyrite in the mine spoil can generate colloidal pyrite, which is mobilized and transported by soil pore water. Our results also indicate that these pyritic colloids are associated with toxic trace metals including Cu, Mn, and Zn. Colloid mobilization is also impacted by changes in temperature and precipitation, where clay mobilization afer rain events is favored. Further, sudden spikes in aqueous and/or colloidal concentrations may be the result of local heterogeneity within soils developing on mine spoil, indicating that further field-based work is necessary to better characterize pore-scale processes that control aqueous and colloid transport at similar sites to have a better understanding of potential contaminant transport from mine spoil systems.

58 GEOSCIENCES↗
DOE OSTI2023

Lime slurry treatment of soils developing on abandoned coal mine spoil: Linking contaminant transport from the micrometer to pedon-scale

Historical and abandoned coal mine spoil continues to generate acid- and metal(loid)-rich porewaters and represents a geographically large and diffuse non-point source of contamination to local watersheds. A potentially inexpensive approach to treat these materials and soils developing on them is through the application of lime slurries, to neutralize acidity and encourage the (co)precipitation of metal(loids) with Fe(III)-(oxy)hydroxides, and potentially other metal-oxides and/or Ca-bearing phases. Here, the efficacy of this approach was evaluated through parallel field application and laboratory-based flow-through column experiments. The field site is Huff Run sub-watershed 25 located in Tuscarawas County, Ohio and was chosen in part because it was previously classified as one of the most highly AMD-impacted sub-watersheds in the region. Two locations with historical spoil were chosen and suction lysimeters were installed at 25 and 75 cm depth to monitor porewater composition on two sides at the base of each pile. Half of each slope received seven lime slurry treatments from June through October of 2017. A suite of aqueous (ICP-OES, IC, and TOC-L) and solid phase geochemical and mineralogical approaches (quantitative SEM-EDS and synchrotron μ-XRF) were used to determine how composition, texture, morphology, and spatial distribution of mineral coatings differ in pre- and post-lime treated soils, and how that impacts the distribution and transport of trace metal(loid)s. Mine spoil porewater at site 1 was slightly less alkaline (pH ranging from 7.04 to 7.37) than at site 2 (ranging from 7.55 to 7.71), and average electrical conductivity values at site 1 (316–405 μS cm —1 ) were slightly lower than at site 2 (358–464 μS cm —1 ), although differences between the sites were not significant. Porewater pH and electrical conductivity in all lysimeters decreased over the course of the field season but there was no obvious response to lime treatment at either site or any depth. At site 1, both treatment and depth were significant factors affecting Ca, K, Ni, SO 4 2— , and DOC concentrations while only treatment effects were significant for dissolved Al and Cu (p < 0.05). For all soils, there were no trends in metal concentration observed over time although DOC and SO 4 2— decreased over the field season. Pedon-scale changes in metal porewater concentrations in response to treatment were linked to micrometer-scale changes in mineral surface coatings; specifically, higher concentrations of Ca, Fe, Mn, and Zn were observed in the coatings and no changes were observed in Fe redox speciation, whereas total S decreased likely due to oxidation of S in coal fragments. In contrast to the field experiment, the column experiments exhibited a much greater response in effluent composition with respect to lime treatment. The untreated columns had approximately an order of magnitude more H + leached over the course of the experiment (p < 0.001) and resulted in greater Ca, Al, Cu, and DIC leached and less Mn, Zn, and SO 4 2— . Soils treated with the lime slurry in the column experiments exhibited larger and thicker secondary Fe-coatings, including the addition of Fe-sulfates. Despite clear trends in the laboratory-based column experiment where the lime-to-soil ratio was higher, the effects were either muted or undetected in the field pilot project, suggesting that a higher application rate of lime in the field is needed to achieve a similar effect. This work provides evidence that a less alkaline lime slurry could be a practical and inexpensive method of treating coal mine spoil-impacted soils and represents an important step in linking laboratory-based remediation studies to implemented field-based studies.

58 GEOSCIENCES↗
DOE OSTI2021

Surface and subsurface characterization of laser-interference structured Ti6Al4V

Ti6Al4V specimens were exposed to high-energy laser pulses of 1.24 J/cm 2 fluences per pulse using a two-beam optical configuration to attain laser-interference. In addition to the formation of periodic surface textures by laser-interference, scanning electron microscope (SEM) images demonstrated several microstructural changes on the surface processed. Moreover, the surface and subsurface of Ti6Al4V specimens were characterized for the as-received and laser-interference processed conditions using x-ray photoelectron spectroscopy (XPS) and electron energy dispersive spectroscopy (EDS). The XPS data showed that this laser technique is effective at removal of surface contaminants for Ti6Al4V. The XPS analysis also revealed the formation of an oxy-nitride layer on the laser treated material. Finally, the microstructure analysis indicates that grain refinement, dendrite and twin structures were found near the surface due to laser processing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dry reforming of methane over Ni supported on LaMnO 3 thin films

Thin films of LaMnO 3 were deposited onto MgAl 2 O 4 by Atomic Layer Deposition (ALD) and studied as supports for Ni in the Dry Reforming of Methane (DRM). Scanning Transmission Electron Microscopy (STEM) with Energy-Dispersive X-ray Spectroscopy (EDS) demonstrated that LaMnO 3 covered the support uniformly, and X-ray diffraction (XRD) showed that the LaMnO 3 films maintained their perovskite structure after 5 redox cycles at 1073 K. The Ni also remained well dispersed after 5 redox cycles at 1073 K. The LaMnO 3 -supported catalyst was more active than Ni on the unmodified MgAl 2 O 4 and showed superior resistance against coke formation. Lastly, the results for Ni on the LaMnO 3 films are compared to previous results for Ni on LaFeO 3 , CaTiO 3 , SrTiO 3 , and BaTiO 3 films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Evaluation of IrO 2 catalysts doped with Ti and Nb at industrially relevant electrolyzer conditions: A comprehensive study

A series of commercial Oxygen Evolution Reaction (OER) IrO 2 -based materials doped with acid-stable titanium and niobium species were comprehensively characterized by Brunauer-Emmett-Teller (BET), X-ray diffraction analysis (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS), and X-ray Scattering. Electrocatalysts were integrated into Membrane Electrode Assembly (MEA) using a fabrication method developed under the US DOE H2NEW consortium. An electrolysis performance in a commercial setup as well as a laboratory screening system was performed at conditions relevant to industrial application. According to the comprehensive characterizations, the studied materials are closer to doped iridium oxides rather than core–shell structures. In an electrolysis cell, the IrO 2 /TiO x catalyst slightly outperforms the IrO 2 /NbO x based on the activity. It was demonstrated that the operation of electrolysis cells at elevated temperatures and the implementation of thinner Nafion-type membranes allows for substantially increased performance, which is consistent with the literature report. Finally, this work provides valuable baselines including characterization and performance for guiding future research in this direction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Iridium-cobalt oxide synthesized via surfactant-assisted Adams fusion for efficient oxygen evolution in acidic and alkaline media

A series of iridium-cobalt (Ir-Co) oxide catalysts were synthesized using a modified surfactant-assisted Adams fusion method and evaluated for the oxygen evolution reaction (OER) in both acidic and alkaline media. The effect of varying the Ir/Co ratio was systematically studied and compared with commercial Ir black and pure IrO 2 samples. The actual elemental ratios were quantified using X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectroscopy (EDS), and inductively coupled plasma-mass spectrometry (ICP-MS). Among the synthesized samples, the Ir 6 Co 4 catalyst exhibited the best performance in acidic media, achieving an iR-corrected overpotential of 292 mV. In alkaline conditions, it demonstrated comparable activity to Ir black, with an iR-corrected overpotential of 263 mV. XPS and electron energy loss spectroscopy analyses revealed that increasing Co content led to a higher fraction of metallic Ir (Ir 0 ) in the catalyst. In addition, the role of Ir 3+ in enhancing OER activity was explored. A strong correlation was observed between higher Ir 3+ content and improved OER performance in acidic conditions.

Adams fusion↗
DOE OSTI2026

Novel PtNi single-atom–nanocluster (SA–NC) ensembles promote Tafel kinetics and ampere-class AEM hydrogen evolution

The development of efficient, durable, and low-PGM electrocatalysts for the hydrogen evolution reaction (HER) in alkaline media is critical for next-generation electrolysis technologies. We report a facile two-step synthesis of highly dispersed PtNi and PtNi-nitride nanoclusters (NCs) (~2.3 nm) with ultralow Pt content (0.5 at.%) anchored on N-doped Vulcan carbon. Structural and compositional characterization via XAS, XPS, HAADF-STEM, HRTEM, and EDS mapping established key structure–activity relationships across varying Pt/Ni ratios and pyrolysis temperatures. The Pt0.5Ni0.5/C-750 catalyst, an ensemble of PtNi M-N-C type single-atom (SA) moieties with neighboring PtNi nanoclusters (NC), exhibited superior HER performance in alkaline media, achieving overpotentials of 30, 115, and 210 mV at 10, 100, and 500 mA cm−2, respectively. Despite at a lower Pt content, this novel SA–NC ensemble outperformed commercial Pt/C by ~36%. A standardized literature comparison with contemporary Pt- and Ru-doped analogues reveals the as-prepared Pt0.5Ni0.5/C-750 to sit at the apex of Tafel-limited kinetics and low overpotential at 100 mA cm−2. Tafel-limited Tafel slopes in both alkaline and acidic regimes confirm favorable proton recombination kinetics. Mass activities at 200 mV reached 13.8 and 18.84 A mgPt−1 in alkaline and acidic media, respectively. However, excessive nitridation (e.g., at 650 °C) adversely altered Pt electronic structure and HER kinetics. While Ni enhanced alkaline HER, acidic HER favored Ni-free analogues. Pt0.5Ni0.5/C-750 also demonstrated robust temperature responsiveness and 300-h operational stability at high current densities (0.5–1.0 A cm−2) in MEA tests. This work presents a scalable strategy for designing thermally responsive, durable, and compositionally tunable NC catalysts with neighboring SA moieties for alkaline electrolysis.

AEMWE↗
DOE OSTI2021

Carbon sequestration of steel slag and carbonation for activating RO phase

Carbonation of Ca/Mg minerals in industrial alkaline residues is a technology to sequester CO{sub 2} and reduce its emissions to the atmosphere. In this work, BSE-EDS were used to determine the mineral phase in steel slag; compositions of RO phase were identified and simulated. The carbon sequestration of steel slag was studied, and RO phase was activated by carbonation. Result shows that the amount of CO{sub 2} sequestered in steel slag and RO phase increases as carbonation time increases. Under autoclaving condition, the hydration ratio of MgO in RO phase was 20.10%. Through carbonation, up to 58.83% of MgO in RO phase can be converted into MgCO{sub 3}, and the activation of RO phase by carbonation was manifested. The mechanical properties and volume stability of carbonated steel slag were improved, proving that the positive effect of carbonation on steel slag when applied in cement and cementitious materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of ZnO on the whiteness of white Portland cement clinker

The addition of ZnO to significantly improve the Hunter whiteness of white Portland cement (WPC) clinkers is introduced in this paper. The effects of ZnO on the whiteness of WPC were studied by chroma analysis, X-ray diffraction (XRD), the Rietveld method, hydration heat measurements and SEM-EDS. The results showed that adding ZnO increased the visible light reflectance, increased the brightness (L{sup ⁎}), and reduced the yellowness (b{sup ⁎}) of WPC clinker with high Fe{sub 2}O{sub 3}. Therefore, ZnO can increase the whiteness of WPC clinker. Zn was mainly distributed in the amorphous phase and unquantifiable crystalline phase (ACn), and then dissolved in the silicate phase. ZnO stabilized R-C{sub 3}S, reduced the crystallization of C{sub 3}A, and increased the ACn content. ZnO increased the amount of Fe in the ACn and minerals, thereby reducing the formation of C{sub 4}AF and improving whiteness. ZnO increased the accumulated heat of hydration but prolonged the induction period. This method provides a new approach for the WPC industry to broaden sources of raw materials and improve product quality.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of anionic and nonionic surfactants on the dispersion and stability of nanoSiO2 in aqueous and cement pore solutions

It has been well recognized that the benefits and effectiveness of nanoparticles in cement-based materials could not be maximized if these are not well dispersed. To address this issue, in this study, different anionic (SDS and PCE) and nonionic surfactants (Tweens and Tritons) were used to disperse nanosilica (NS) in aqueous solution and cement pore solution. The results show that the dispersibility of NS in cement pore solution was improved, and the compressive strength of the cement-NS pastes increased linearly with critical micelle concentration (CMC) of nonionic surfactants. Among all surfactants studied, Triton X-405 led the paste to the highest increase in strength (33% at 1-day and 41% at 3-days) since it had the highest CMC. TEM and EDS analysis evidenced that this strength increase might be attributed to the nucleation of outer product CSH gel and its densification with calcite nanocrystals, attributed to Triton X-405 addition.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Feldspar-based CaO–K 2 O–Na 2 O–BaO silicate glass sealant for solid oxide fuel cells

Sealants have been widely used in solid oxide fuel cells (SOFCs), and glass sealants have shown considerable potentials due to their low leakage rate. In this paper, we report a type of feldspar-based glass sealant, mainly composed of CaO-K 2 O-Na 2 O-BaO, with a coefficient of thermal expansion (CTE) of 10.11×10 -6 k -1 , a glass transition temperature at 528°C, and a softening temperature at 573°C. Using this sealant to seal anode-supported SOFCs, the open-circuit voltage (OCV) remains at 1.08V after five thermal cycles and 50-hour aging at 750°C, close to the theoretical OCV value. The SEM and EDS reveal stable interface between the glass sealant and the anode, indicating excellent performance of the CaO-K 2 O-Na 2 O-BaO glass sealant for SOFC sealing applications.

25 ENERGY STORAGE↗