Search NASA⌕ Search

SEARCH · Search NASA

Results for “LINERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Validation and Parametric Investigations Using a Lumped Thermal Parameter Model of an Internal Permanent Magnet Motor

One of the key challenges for the electric vehicle industry is to develop high-power-density electric motors. Achieving higher power density requires efficient heat removal from inside the motor. In order to improve thermal management, a multi-physics modeling framework that is able to accurately predict the behavior of the motor, while being computationally efficient, is essential. This paper first presents a detailed validation of a Lumped Parameter Thermal Network (LPTN) model of an Internal Permanent Magnet (IPM) synchronous motor within the commercially available Motor-CAD® modeling environment. The IPM motor’s stator is studied at steady state, and winding losses are generated by a constant DC current. The validation is based on temperature comparison with experimental data and with more detailed Finite Element Analysis (FEA). All critical input parameters of the LPTN are considered in detail for each layer of the stator, especially the contact resistances between the impregnation, liner, laminations and housing. Finally, a sensitivity analysis for each of the critical input parameters is provided. A maximum difference of 4% — for the highest temperature in the slot windings and the end windings — was found between the LPTN and the experimental data. Comparing the results from the LPTN and the FEA model, the maximum difference was 2% for the highest temperature in the slot windings and end windings. As for the LTPN sensitivity analysis, the thermal parameter with the highest sensitivity was found to be the liner-to-lamination contact resistance. The latter is often ignored in the literature, whereas its impact on temperature rise was found to be more significant than any other contact resistance within the stator.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Pellet cladding mechanical interaction as a potential failure mechanism during a control rod drop accident in a boiling water reactor

Boiling water reactors (BWRs) represent approximately one-third of the operating fleet in the United States, contributing significantly towards the global effort in reducing carbon emissions. Even though most of the operating fleet has been in operation for quite some time, continued advancements in new nuclear fuel (such as accident tolerant fuel) or operating regimes (such as power up-rates and higher burnup operation) necessitates similar advancements in modeling and simulation capabilities. Bison, a component of the Virtual Environment for Reactor Applications (VERA), is a high-fidelity fuel performance code able to explore the fuel performance of a wide variety of fuel types in one-, two-, and three-dimensions. Until recently, the code had not been used for analyses of BWRs. Modeling capabilities have been added for Gd-bearing UO{sub 2} and pure zirconium liners. New models have been added based upon the U.S. Nuclear Regulatory Commission (NRC) guide-lines for hydrogen pickup in Zircaloy-2 claddings and pellet-clad mechanical interaction (PCMI) failure during a reactivity insertion accident (RIA), known as a rod drop accident (CRDA) in BWRs. Implementing and/or improving Bison modeling capabilities extended its analytical reach to areas beyond its original intended purpose. This paper demonstrates one of these capabilities as a proof of concept. Recently developed models enable Bison to provide an alternate approach for cladding integrity determination in CRDA evaluations, which currently use bounding conservative estimates. As part of this demonstration, NRC guidance on hydrogen-pickup and PCMI failure models were utilized in this research. Even though more research is needed in establishing right inputs and process in this area, this paper demonstrates Bison's ability to determine cladding integrity in a CRDA evaluation. This first of a kind demonstration is a proof of concept in this area, which could potentially be extended to a number of other areas where a more accurate cladding integrity determination would be needed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

(U) PRAD0697 & PRAD0698: Complex Loading of CeO₂ Powder

Cerium(IV) oxide (CeO₂) powder is shock compressed using the Precision High Energy-density Liner Implosion eXperiment (PHELIX) platform. Experimental results are compared against several modeling approaches. Compaction behavior is best captured with a P-∝ model, which calculates CeO₂ powder bulk densities within 80-99% of experimental values but overpredicts densi cation at the cylindrical target's outer radius and center by up to 20%. Preliminary calculations suggest that accuracy could be increased with the inclusion of a coupled strength model. Several common computational modeling approaches for the shock compression response of granular materials and the magnetohydrodynamic (MHD) force upon the impactor/liner in pulsed power compression experiments are investigated and analyzed for their validity. The Bi-linear Ramp, P-∝ PACXP, and P-∝ Menikoff-Kober continuum compaction models are calibrated to planar impact Hugoniot data for CeO₂ powder and used to predict the powder's shock compaction response under non-planar shock wave compression. MHD calculations of the PHELIX pulsed power driver are performed using an idealized resistor-inductor-capacitor (RLC) circuit calibrated to previous experiments. All simulations are performed using the LANL code FLAG. Two validation experiments are computationally designed using the calibrated compaction and circuit models, executed using the PHELIX platform on CeO₂ targets with initial porous densities of 3.95 and 4.03 g/cm³, measured with proton radiography, and analyzed against the model predictions. The two P-∝ models more accurately describe CeO₂ powder densi cation than the Bi-linear Ramp model. However, the two P-∝ models overpredict bulk density of the shock compressed CeO₂ powder by up to 20% when the appropriate impact velocities are applied. MHD calculations for both validation experiments underpredict liner impact velocities by 4-11% when using the idealized RLC circuit model calibrated to previous experiments. Compensating underpredictions of impact velocity and overpredictions of powder densication lead to a false accuracy in pre-shot calculations compared to experimental data. To improve correlation between simulations and experiments, the following improvements are suggested: 1. A coupled strength model for CeO₂ powder that updates strength as a function of porosity and applied stress. 2. An improved MHD circuit model that more accurately captures the PHELIX machine.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Advanced Moderation Module for High-Temperature Micro-Reactor Applications

Development and deployment of micro-reactors that provide competitive efficiency, prevailing compactness, and inherent safety is an immediate focus of the U.S. nuclear industry. For thermal neutron micro-reactors operating at elevated temperature for optimized efficiency, such as micro molten-salt reactors (MSRs), heat-pipe reactors, and very-high temperature reactors (VHTRs), high-performance moderator based on metal hydride can enhance the neutron economy and therefore achieve reduced weight and enhanced portability. As unclad metal hydride inevitably decomposes at elevated temperature, an enclosure is required for hydride moderator to deliver desired performance at elevated temperatures. Conventional moderator enclosure solutions based on high-temperature alloys introduce extraneous neutron penalty into the micro-reactor, affecting the neutronic benefits provided by the hydride moderator. Additionally, the compatibility between the high-temperature alloy enclosure and the micro-reactor matrix is also a potential issue. In this report, we disclose an Advanced Moderator Module (AMM) concept enabled by an innovative enclosure solution combining the advantages of refractory metals, ceramic matrix composites (CMCs), and advanced coating technology to serve as hydrogen permeation barrier up to very-high temperatures. A schematic description of the AMM structure is illustrated in Figure A1. The AMM contains a moderating material core made of metal hydride with high thermal stability, such as YH 2-x . The hydride core is enclosed by an H 2 barrier layer coated on a ductile refractory metal liner to minimize hydrogen loss during high-temperature operation. A ceramic matrix composite (CMC) cladding is adopted to provide further structural strength, especially during power transients. Between the CMC cladding and metal liner, an extra diffusion barrier coating is inserted to suppress the chemical interaction at elevated temperatures. Hence, based on a series of innovative material solutions, the AMM is capable of containing the metal hydride core at elevated temperature (>900oC) inside coated and lined CMC envelop with negligible hydrogen loss throughout the microreactor lifetime. The benefit of the AMM technology was assessed based on a comprehensive multi-stage reactor-physics analysis. Advanced moderation based on hydride metals (such as YH2-x) enables reaching optimum moderation with higher fuel content than traditional VHTR technology, which is required to design compact micro-reactor cores targeting long-life operation. The AMM enclosure technology provides lower thermal neutron absorption rates than traditional solutions (based on stainless steel or Mo-based alloy such as TZM), which reduces the fissile enrichment requirements by 6-8% on a TRISO-fueled design based on the EMPIRE core. Finally, combining the hydride moderator with neutron transparent enclosure solutions provides significant potential to boost neutronics performance of micro-reactors in terms of increased core lifetime or reduced size and weight by 30-50% on a micro-reactor based on the Holos Quad technology. The progress and plans for on-going development and demonstration efforts are also discussed in this report. The current demonstration of AMM is focused on the hydrogen diffusion barrier demonstration under thermal cycling, while radiation tolerance demonstration is planned. The next step of the demonstration plan will be the assembly of miniature AMM for high-temperature testing, which can be used as a prototype for future pilot scale demonstration.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Functional Photoresists for Energy Applications. Final Report

Monolithic ultralow-density porous bulk materials have recently attracted much interest due to many emerging applications in the areas of catalysis, energy storage and conversion, and thermal insulation. They are also important components of high energy density (HED) and inertial confinement fusion (ICF) targets. However, despite tremendous progress that has been made in the synthesis of porous materials, deterministic and independent control over microscopic architecture, density and composition remain key issues, and their integration in high precision devices requires cost and time-intensive mechanical machining that not only reduces reproducibility by generating debris but also limits the complexity of the 3D shapes that can be realized. In this project, we overcame these limitations by developing a universal templating capability that provides deterministic and independent control over density, composition, architecture, and macroscopic sample shape. This was achieved by developing the technology to 1) 3D print ultrahigh resolution, ultra-high precision polymeric micro-lattice templates, 2) coat these templates with the desired materials, and 3) removing the template (Fig. 1a). Atomic layer deposition (ALD) provides the atomic scale coating thickness accuracy required for precisely controlling density. While this templating approach had been demonstrated in prior work, limitations in suitable photoresists, 3D print technologies, print design, and template removal techniques did not allow the fabrication of millimeter-sized high-precision parts with sub-micron resolution. To enable this technology, we developed 1) two-photon polymerization (TPP) print designs that enable the fabrication of millimeter-sized, mechanically robust polymeric templates with sub-micron resolution and 2) a continuum level TPP printing simulation capability for additional print design guidance; 3) atomistic models to study photoresist polymerization kinetics and network topography, 4) refractive index matched polymeric and preceramic TPP photoresists, and 5) functional TPP photoresists including porous voxel structures and self-immolative polymer photoresist chemistries; and 6) damage free template removal techniques that enable the fabrication of defect-free high-precision low-density foam components. We also developed a templating approach for pure carbon microlattices with a unique tube-in-tube ligament morphology. As a test platform, we pursued the fabrication of foam liners that promise to further increase the neutron yield in indirect drive ICF experiments by improving implosion symmetry control and coupling between the laser and the deuterium-tritium fuel. This application requires fabrication and integration of a ultra-high precision, millimeter-sized, thin-walled (200-400 micrometer thick), low-density (10-30 mg/cc), high atomic number (high Z) cylindrical foam tube into the gold hohlraum of an indirect drive ICF target (Fig. 1b). While our hohlraum liner test case will mainly find application in HED and ICF experiments, the underlying science will also directly apply to previously developed nanoparticle and additive manufacturing technologies and will advance those techniques as well.

36 MATERIALS SCIENCE↗
DOE OSTI2020

BWR Spent Nuclear Fuel Acquisition and Testing to Support DOE-NE High Burnup Spent Fuel Data Project

The Office of Spent Fuel and Waste Disposition (SFWD) within the US Department of Energy (DOE) Office of Nuclear Energy (NE) established the Spent Fuel and Waste Science and Technology (SFWST) campaign to conduct research and development (R&D) activities related to the storage, transportation, and disposal of spent nuclear fuel (SNF) and high-level radioactive waste. The SFWST program was created within SFWD to address issues of extended or long-term SNF storage and transportation. Some near-term objectives of SFWST are to use a science-based, engineering-driven approach to: Support the enhancement of the technical bases to support the continued safe and secure dry storage of SNF for extended periods; Support the enhancement of the technical bases for retrieving SNF after extended dry storage; Support the enhancement of the technical bases for transporting high burnup (HBU) fuel and transporting low burnup fuel and HBU fuel after dry storage DOE-NE, in partnership with the Electric Power Research Institute, developed the High Burnup Spent Fuel Data Project to perform a large-scale demonstration and laboratory-scale testing of HBU pressurized water reactor (PWR) fuels (exceeding 45 gigawatt-days per metric ton of uranium [GWd/MTU]). Under this project, 25 sister rods—which are rods that have the same design, power histories, and other characteristics—were removed from assemblies at the North Anna Nuclear Power Station and sent to Oak Ridge National Laboratory (ORNL) in January 2016. ORNL performed detailed nondestructive examination (NDE) on all 25 rods. The NDE consisted of visual examinations, gamma and neutron scanning, profilometry and rod length measurements, and eddy current examinations. After completing the NDE, 10 of the sister rods were delivered to Pacific Northwest National Laboratory (PNNL) in a NAC International, Inc. legal-weight truck cask in September 2018 for destructive examination (DE). To date, SFWD work has focused on the PWR fuel that is part of the Sister Rod Test program. No boiling water reactor (BWR) fuel has been tested in the program, and the data needs that were identified for the PWR fuel have not been collected for BWR fuel. The goal to obtain six to nine BWR rods and test them at ORNL will support closing this important data gap. BWR fuel comprises approximately 56% of the total fuel assemblies currently in storage at nuclear power plants in the United States. BWR nuclear fuel and cladding designs and manufacturing are significantly different from PWRs. Differences include the following: BWR fuel pellets are larger than PWR pellets; Variations of Zircaloy-2 (including liners) are used instead of the Zircaloy-4 cladding materials used in PWRs; Clad manufacturing and stress-relief processes are different between PWRs and BWRs; The fuel rod dimensions are different because larger rod diameters and thicker cladding are used in BWRs; BWR fuel typically has lower internal rod pressures and sees vastly different operating conditions than PWR fuel (i.e., two-phase flow); BWR assemblies are “canned,” meaning each assembly is surrounded by a metal fuel channel; BWR cladding is often composed of an inner pure Zr liner that has widely different mechanical properties than the Zircaloy-2 alloy and exhibits a stronger affinity for hydrogen; The BWR SNF generally has more total hydrogen in the cladding/liner than typical PWR fuel; The construction of the PWR and BWR assemblies is vastly different; BWR rods are solidly attached to the assembly nozzles and experience a much different vibration and shock load than PWR rods, which are “floating” within a grid system attached to guide tubes, and the rods sit loosely on the bottom end plates. These numerous differences will affect the way the BWR SNF responds under dry storage preparation processes (e.g., vacuum drying) and during transportation. The results collected in the PWR experimental program must be compared with a subset of similar data collected on BWR SNF to establish a technical basis for whether the larger PWR database is sufficient to bound the BWR SNF end-of-life conditions as is currently assumed for several fuel/clad properties. Changes that occur in both fuel types at HBU could exacerbate any mechanical property differences. As the fuel burnup increases, several changes occur that might affect the performance of the fuel, cladding, and assembly hardware in storage and transportation. These changes include increased cladding corrosion layer thickness, increased cladding hydrogen content, increased cladding creep strains, increased fission gas release, and the formation of the HBU structure at the surface of the fuel pellets. The Nuclear Regulatory Commission (NRC) limits the current maximum rod-averaged burnup to 62 GWd/MTU due to these changes and the lack of data at higher burnups.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

High Temperature Thermal Barrier Coating Evaluation of Yttrium Aluminum Garnet for Gas Turbine Applications

The Solution Precursor Spray Process (SPPS) process has been shown to overcome the durability and property challenges of applying yttrium aluminum garnet (YAG) coating for high temperature thermal barrier coating (TBC) applications (1200°C+) but only limited testing has been performed in representative application environments. In this study, YAG coatings were developed to optimize microstructure and tailor properties for combustion components in an industrial gas turbine. Thermal conductivity, erosion resistance and furnace cycling durability were used to validate YAG properties against the standard yttria-stabilized zirconia coating (YSZ). Graded and multi-layered microstructures were applied to enhance performance while maintaining durability. Further YAG process development was required to replicate coating properties and optimize deposition on more complex fuel injector nozzle and combustion liner components. Rig testing of both components was performed and compared against the baseline YSZ coating validating the high temperature capability and lower thermal conductivity of the SPPS YAG coating. The components in both tests were cycled for a minimum of ten cycles with the fuel injector test targeting a higher operating temperature while the combustor liner operated at standard conditions. A development engine test is planned to further validate performance in a gas turbine engine of this promising material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ultra-High Temperature Thermal Barrier Coating Development and Validation

The most effective method to improve industrial gas turbine power is to increase firing temperature. To maintain component durability at these higher temperatures, thermal barrier coatings (TBC’s) are playing an increasing role in protecting turbine hardware. TBC’s have been successfully used on Solar Turbines’ combustor liners and turbine airfoils, but there is a need for TBC’s that can operate at higher temperatures. Based on recent, favorable rig testing experience, Solar recognized that yttrium aluminum garnet (YAG) TBC’s made by the Solution Precursor Plasma Spray Process (SPPS) has great potential for higher turbine temperatures. This testing verified the thermal cycle durability of the SPPS YAG TBC’s, as well as demonstrated that the temperature drop through the SPPS YAG TBC was twice that measured across a companion APS YSZ TBC. The SPPS YAG TBC with the potential for a 200°C improvement in temperature capability represents a materials breakthrough. The SPPS process also produces a number of unique microstructural features that confer superior properties. SPPC TBC’s have ultra-fine splats that increase toughness and erosion resistance, and the process can be tailored to produce through-thickness cracks for strain-tolerance and control porosity for lower thermal conductivity and increase coating abradability. This proposal would include further development of SPPS YAG density-graded coatings, optimization of the application process, and validation of higher temperature capability and durability through rig and engine testing of coated combustion liners and turbine outer air seals. The technology would be advanced from a TRL 3 to a proposed TRL 6 by overcoming processing concerns on efficiency, application distance and optimization of a graded coating without impacting coating durability by demonstrating the coating performance on components in rig and development gas turbine engine testing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hanford Double Shell Waste Tank Corrosion Studies (Final Report)

For fiscal year (FY) 2022, the Savannah River National Laboratory (SRNL) focused on two experimental tasks related to Hanford Double Shell Tank (DST) chemistry and integrity. The first task focused on understanding risk of corrosion due to formation of either continuous layers or discrete patches of solids on the tanks' inner sidewalls and bottoms. The tank bottom solids contact corrosion testing focused on studying the effects of forming a dry adherent solids layer on a carbon steel substrate. Long-term exposure tests and electrochemical tests were performed to investigate the effect of drying (i.e., removing water) from the solids phase. The second task focused on corrosion of the exterior of the secondary liner. In previous years, vapor corrosion inhibitors (VCIs) were investigated as a means of mitigating corrosion of the exterior of the secondary liner. During FY22 the utilization of nitrogen was explored as a means of corrosion mitigation. The corrosion test results with nitrogen were compared with the corrosion mitigation performance of the VCIs.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

HFTS-1 (Final Report)

Despite the long history of hydraulic fracturing, the optimal number of fracturing stages during multi-stage fracture stimulation in horizontal wells can be a complex subject. In addition to the increased expense of multistage fracturing in horizontal wells, increasing the number of fracturing stages does not always correlate with a commensurate increase in production. The problem is the application of a uniform fracture stimulation design to all stages with no consideration for geological variations along the wellbore. The result is an inefficient use and costly waste of energy and water. Optimization of the fracturing process requires an understanding of the cause-and-effect relationship between fracturing parameters and local geological properties at a given location along the wellbore. Realizing that the generalized rock mechanics theories and hypotheses are not truly applicable to fractured and laminated shales, quantifiable impacts of a shale’s geomechanical and depositional features are a prerequisite for design and implementation of optimized hydraulic fractures. The overarching goal of this project is to understand and define the relationships of shale geology and fracture dynamics using detailed field data that includes coring of the fracture domain. Finally, resource recovery from shale formations is estimated to be less than fifteen percent. Research proposed in this project will establish the foundations for investigating enhanced recovery techniques for increased resource recovery in existing fracture treated wells. Natural gas as an EOR fluid is in the initial stages of being used broadly in the oil and gas industry and as such, many aspects of the process need to be researched and addressed prior to widespread acceptance. In addition, re-fracturing techniques, particularly using cemented liners also need to be further investigated. This project explores several of these EOR techniques in greater detail, not just at the theoretical level, but through actual field test sites. This report delves into the research program, identified tasks, several studies, observations, results, and conclusions under the Hydraulic Fracturing Test Site (HFTS) project. This test project is subdivided into three distinct phases and each phase is discussed in detail under separate sections. The original test site for Phase 1 as well as the Phase 2 site are in Midland Basin in Texas and operated by Laredo Petroleum. In the first two phases, the program targeted the Wolfcamp formation in Midland Basin. Phase 3 of the study targeted the EagleFord play in South Texas with Devon Energy as the operator. Significant conclusions from this study include: 1) lateral and vertical fracture growth mapping as well as proppant transport behavior, 2) Use of field gas and its applicability for huff n puff EOR injection in the Midland Basin, 3) Development and validation of proppant log, both at core scale as well as in-fill well implementation by analyzing drilling mud return samples, 4) Applicability of liner refracturing including best practices for enhanced unit level productivity. This report will detail all these studies as well as technical results and conclusions from said studies. These include general subsurface characterization work, completion designs as implemented, studies looking at fracture geometry, high resolution microseismic study, advanced crosswell strain mapping studies including drainage characterization, core characterization results, proppant analysis (core and observation wells), geochemistry, etc. to name a few.

02 PETROLEUM↗
DOE OSTI2024

Degradation of performance in Z-pinch implosions due to shell and magnetic-drive asymmetries

Achieving maximum performance in a Z-pinch Magnetized Liner Inertial Fusion (MagLIF) implosion requires high levels of symmetry to reach high pressures, high areal densities, and high efficiency energy coupling between the compressed fuel and the imploding shell. In this work, we present the development of a nonlinear model to describe an asymmetric MagLIF liner undergoing magneto-Rayleigh-Taylor (MRT) instabilities in the z = 0 plane. We investigate and present results from our model that show the degradation of the pressure at stagnation under various kinds of asymmetries that can arise during MagLIF experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

TuFF internal WRAP for Rapid Pipeline Repair (TuFF iWRAP)

The goal of “TuFF internal WRAP for Rapid Pipeline Repair” (TuFF iWRAP) program was to develop a novel material system and placement process to fabricate structural pipe within the existing deteriorated pipelines without disruption of gas delivery. The team (University of Delaware – Center for Composite Materials (UD-CCM) and Plitzie Inc.) addressed this challenge by developing a new material feedstock and pipe in pipe (PIP) repair strategy. This allows the potential for significant cost reduction and has minimum operational impact on gas customers. The new robotic based placement design allows discontinuous placement of pipe sections creating a stand-alone structural liner within the legacy pipeline without the need for pipe shutdown. Here, the material is supplied using a tethered material feeding system and is placed and UV cured with the internal Wound Rapid Automated Placement (iWRAP) system. This provides maximum placement efficiency capable of traversing 90 angle bends in 12-inch pipe and overall design customization to meet pipe repair requirements (e.g., variable wall thickness, bridging gaps, etc.). UV-curable fiber reinforced composite material has been optimized to meet structural performance and placement/cure times. Superior strength and fatigue life has been demonstrated by improving fiber-matrix adhesion using new fiber sizing for UV resins. Rapid cure approaches using new liner and resins have been evaluated with industry. The appropriate design of the section joints has been developed and tested. We estimate coating time to be ~100 hours per mile enabling typical pipe repair within 1 week.

03 NATURAL GAS↗
DOE OSTI2020

Combustion system with panel fuel injector

The present disclosure is directed to an annular combustion system. The annular combustion system includes an inner liner and an outer liner that define therebetween an annulus that circumscribes a centerline of the combustion system. The annulus includes a plurality of primary combustion zones defined at an upstream end thereof and further defines a plurality of secondary combustion zones downstream of the primary combustion zones. The annular combustion system further includes a plurality of fuel nozzles where at least one fuel nozzle discharges a combustible mixture into a respective primary combustion zone of the plurality of primary combustion zones. A plurality of panel fuel injectors is disposed between adjacent fuel nozzles. The plurality of panel fuel injectors extends in an axially downstream direction so as to separate adjacent primary combustion zones. Each panel fuel injector discharges a combustible mixture into at least one secondary combustion zone.

42 ENGINEERING↗
DOE OSTI2020

Validation and Parametric Investigations Using a Lumped Thermal Parameter Model of an Internal Permanent Magnet Motor: Preprint

One of the key challenges for the electric vehicle industry is to develop high-power-density electric motors. Achieving higher power density requires efficient heat removal from inside the motor. In order to improve thermal management, a multi-physics modeling framework that is able to accurately predict the behavior of the motor, while being computationally efficient, is essential. This paper first presents a detailed validation of a Lumped Parameter Thermal Network (LPTN) model of an Internal Permanent Magnet (IPM) synchronous motor within the commercially available Motor-CAD® modeling environment. The IPM motor’s stator is studied at steady state, and winding losses are generated by a constant DC current. The validation is based on temperature comparison with experimental data and with more detailed Finite Element Analysis (FEA). All critical input parameters of the LPTN are considered in detail for each layer of the stator, especially the contact resistances between the impregnation, liner, laminations and housing. Finally, a sensitivity analysis for each of the critical input parameters is provided. A maximum difference of 4% - for the highest temperature in the slot windings and the end windings - was found between the LPTN and the experimental data. Comparing the results from the LPTN and the FEA model, the maximum difference was 2% for the highest temperature in the slot windings and end windings. As for the LTPN sensitivity analysis, the thermal parameter with the highest sensitivity was found to be the liner-to-lamination contact resistance. The latter is often ignored in the literature, whereas its impact on temperature rise was found to be more significant than any other contact resistance within the stator.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Modular gradient-free shaped charge

A shaped charge produces a constant velocity jet. The shaped charge is comprised of individual modules which can be assembled to produce a constant velocity jet of arbitrary length. The resulting jet speed is approximately twice the detonation velocity and independent of the liner material. The modular design also allows different liner materials to be used sequentially in the same jet.

42 ENGINEERING↗
DOE OSTI2022

Ceramic airfoil trailing end configuration

An airfoil includes an airfoil body that has a trailing edge region. The trailing edge region includes first and second monolithic ceramic exterior walls, a flow discharge passage between the first and second monolithic ceramic exterior walls, a ceramic matrix composite (CMC) liner at least a portion of which is disposed in the flow discharge passage between the first and second monolithic ceramic exterior walls, and an array of pedestals disposed in the flow discharge passage. Each of the flow guides bridges the CMC liner and at least one of the first and second monolithic ceramic exterior walls.

Kennedy, Matthew B.↗
DOE OSTI2023

Direct Numerical Simulation of Flame-Wall Interaction for Low-Carbon Gas Turbine Combustion

Green hydrogen (H2) and ammonia (NH3) are emerging as carbon free alternatives to hydrocarbon fuels. In gas turbines, flames interact with the combustor liner (wall), which affects the pollutant emissions, the burning efficiency, and the thermal load on the liner. We lack understanding of this important flame-wall interaction (FWI) for alternative fuels. FWI occurs at the scale of the flame thickness, and such scales are only resolved by direct numerical simulation. Here, we resolve the FWI for NH3 and H2 flames. Preliminary results of two distinct projects are presented: 2D laminar anchored V-flame, and 3D turbulent swirling flame. For the laminar flame, we show flame quenching at the wall and resulting leakage of NH3 and increased N2O, but decreased NO emissions. For the swirling flame, we show CO emissions, and comparison of flame shapes and location to experimental measurements. Ultimately we show that quenching and pollutant emissions strongly affected by fuel/air ratio, and that an inclined wall can stabilize very lean turbulent CH4/H2 flames, but prone to large CO emissions.

adaptive mesh refinement↗
DOE OSTI2020

Double-Shell Tank Primary Bottom Visual Inspection Results - 20025

A pressing need for the Double-Shell Tank Integrity Program at Hanford is of the ability to inspect the bottom of the tanks. Though the DSTs' annulus spaces (the space between the internal and external tank walls) have been inspected visually since 1992 and with Ultrasonic Testing (UT) since 1996, inspections of the tank bottoms have been able to be conducted due to limitations of available technology, omitting about 40 percent of the tank surface below the maximum fill level from routine inspection. Visual inspections of the tank annulus have been conducted up to five times in some DSTs and portions of the annulus space for all of the DSTs has been inspected twice with UT. This region includes the walls of the primary tank and secondary liner along with accessible portions of the secondary liner bottom. Due to this lack of technology, the degradation of the primary tank bottom in Tank AY-102 was undetected until the tank leaked into its annulus space, confirmed in 2012. Since that time, WRPS has been working with the nondestructive examination community and the Pacific Northwest National Laboratory, to evaluate potential technologies to conduct these challenging remote inspections. Recent work has included the development, testing, and deployment of several remote visual inspection technologies to observe the condition of the primary tank bottom of the DSTs by leveraging air distribution slots in the refractory pad on which it rests. Robotic solutions to conduct this inspection were developed with a detailed understanding of the physical configuration and operational logistics. Understanding and subsequent communication of these details to vendors within the robotics and nondestructive examination community was a critical component to the successful production of these new tools. Throughout the FY16-FY18 years, vendors from nondestructive examination community were solicited for ideas to meet the tank bottom inspection challenge. Two tank bottom visual inspection solutions were then pursued to meet that challenge. Both tools were successfully deployed at Tank AP-107, and provided valuable visuals, never before obtained from the under tank environment of a double-shell tank. While there are minor opportunities for improvement identified with each system, general outcomes were overwhelmingly positive. Both systems were successfully able to navigate the refractory air slot pattern from the outer edge to the tank center and record video footage. The micro-crawler provided high quality and very stable footage through the air slot pattern, but took longer to deploy into the slots and traverse through them than the alternative system. The push-pull tethered camera was able to navigate all seven of its target air slots in a matter of a few hours, which included deployment, movement between slot entrances, and complete removal of the system from the annulus environment. Through these air slots, new information was gained about the tank bottom and refractory pad condition of tank AP-107, AP-106, AP-108, and AN-102. While some debris was noted in the air slots, including sand, chipped refractory, and construction materials, the refractory was found to be structurally stable and adequately supporting the primary tank bottom through the full diameter of the tank. Primary tank bottom steel exterior was found to be in good condition, free of ongoing or aggressive corrosion conditions. Looking toward the future, robotic access to and visual inspection of refractory air slots and the primary tank bottom steel has now proven viable. Incorporating periodic air slot inspections as a regular practice within the Double-Shell Tank Integrity Program is the next step, allowing trending of any changes in condition. As ultrasonic testing infrastructure was leveraged to complete the initial system deployments described in this report, it makes sense to adopt that same strategy for ongoing periodic examinations and deploy these primary tank bottom inspection tools alongside ultrasonic testing operations. Development of visual inspection tools to evaluate the primary tank bottom region of the double-shell tanks was planned as the first stage of inspection. Continued development of volumetric sensors and incorporation of these inspection tools into Hanford's ongoing Double-Shell Tank Integrity Program are the next steps, seeking to continuously expand understanding of asset integrity and remaining useful life. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗