Search NASA⌕ Search

SEARCH · Search NASA

Results for “Plasma Surface Interactions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

An investigation of arc discharging on negatively biased dielectric conductor samples in a plasma

Proposals are now being developed for the construction of high-power photovoltaic systems for operation in low Earth orbit, where the plasma number density is about 1,000 to 1,000,000 per cubic cm. Existing data indicate that interactions between the plasma and high-voltage surfaces of an orbiting power system will occur. In ground tests, where the applied voltage is increased negatively from ground, the array current collection shows an approximately linear rise until it terminates in arcing at greater than several hundred volts negative. This arcing may reduce the power generation efficiency and could possibly affect the low-level logic circuits of the spacecraft. Therefore it is important that the arcing phenomenon be well understood. This study is a survey of the behavior of different dielectric-conductor samples, including a solar cell module, that were biased negatively in a low-density plasma environment with the intent of defining arc discharge conditions and characteristics. Procedures and results are discussed.

Miller, W. L.↗
DOE OSTI2024

Design and analysis of actively-cooled, edge-transport diagnostic for long-pulsed operation in WEST

Next step fusion devices that will operate in steady-state will require complex plasma-facing components (PFCs) that can survive the harsh environment over long timescales not common in current devices. This will require robust plasma facing surfaces that are integrated with active cooling systems. In a collaboration between CEA and ORNL, a plasma-interacting diagnostic is being designed for the W Environment in Steady-state Tokamak (WEST) in Cadarache, France which requires plasma-facing protection like those needed for steady-state PFCs. This integrated diagnostic studies edge transport and impurity migration within WEST, and is planned to include imbedded temperature Langmuir probe sensors, as well as removeable sample slots for ex-situ surface analysis of plasma-material interactions. The entire assembly is expected to move into the plasma edge for periods up to 1000 s having an energy removeable capability of ∼6 kW and seeing a peak heat flux of more than 7 MW/m2. The assembly compliments WEST high fluence campaigns that plan for multiple 1000 s pulses. Within these specifications, the assembly will require a refractory metal plasma facing surface and integral cooling in order to function within the limited space allotted for such diagnostics. Because of the limited space and linear actuator needs, additive manufacturing of the high heat flux working end of the assembly is being considered which could allow for precision cooling-channels and lighter weight designs. Conceptual design along with simulation and analysis results will be presented for this complex diagnostic with novel PFCs.

Lumsdaine, Arnold↗
NASA NTRS1987

Interactions of oblique interplanetary discontinuities and their manifestations during STIP intervals 15-19

The generation of slow shock waves as the result of the interaction of Alfven discontinuities with solar wind contact surfaces is considered. The latter are taken to be the boundaries of proton and alpha-particle concentration inhomogeneities. It is found that the intensity of the Alfven discontinuity may be increased as the result of its interaction with the more dense plasma. The converse (i.e., decrease of the Alfven discontinuity's intensity following interaction with a less dense plasma) is also indicated. Also discussed is the generation of a magnetic cloud as the result of the interaction of a quasi-parallel Alfven discontinuity with a dense plasma contact surface. It is shown that the (solar-generated) Alfven discontinuity may then be transformed into non-flare fast and slow shock waves as the result of this interaction. Thus, it is indicated that some fast shock waves in the solar wind may have a nonsolar origin.

Grib, S. A.↗
DOE OSTI2022

Formation of carbon and oxygen rich surface layer on high purity magnesium by atmospheric carbon dioxide plasma

Carbon and oxygen-rich corrosion barrier layer formed on Mg by a simple and scalable CO 2 atmospheric plasma (CO 2 -AP) process. The reactive CO 2 -AP interacts with the Mg surface and forms a unique layered structure with the top MgCO 3 /MgO-intermixed particulates pillars and the bottom dense layer. The surface features were simultaneously formed on the nano-/micro-structured MgO layer by carbonate molecules, plasma-active CO 2 molecules, and/or other volatile organic compounds on the nano-/micro-structured MgO particle layer. The resulting surfaces after CO 2 -AP were either hydrophobic or hydrophilic and exhibited lower anodic current or high resistance for Mg corrosion. For the hydrophobic surfaces of CO 2 -AP treated Mg, molecular dynamic simulations were performed to understand the origin of hydrophobicity and identified that the amorphous carbon layers formed on the Mg surface are the source. The environmentally benign abundant-gas-based process enables the cost reduction associated with waste treatment, generation of by-product, and supply of raw material.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Numerical Thermal Model of a 30-cm NSTAR Ion Thruster

A thermal computer model of the NSTAR (Nasa Solar Electric Propulsion Technology Applications Readiness) xenon ion thruster has been produced using a lumped parameter thermal nodal network scheme. This model contains 104 nodes on the thruster and was implemented using SINDA (Systems Improved Numerical Differencing Analyzer) and TRASYS (Thermal Radiation Analyzer System) on various UNIX workstations. The model includes radiation and conduction heat transfer, the effect of plasma interaction on the thruster, and an account for finely perforated surfaces. The model was developed in conjunction with an NSTAR thruster outfitted with approximately 20 thermocouples for thermal testing at the NASA Lewis Research Center. The results of these experiments were used to calibrate and confirm the computer model first without and then with the plasma interaction. The calibrated model was able to predict discharge chamber temperatures to within 10 C of measured temperatures. To demonstrate the ability of the model under various circumstances the heat flux was examined for a thruster operating in the environment of space.

VanNoord, Jon↗
NASA NTRS1985

Surface interactions and high-voltage current collection

Spacecraft of the future will be larger and have higher power requirements than any flown to date. For several reasons, it is desirable to operate a high power system at high voltage. While the optimal voltages for many future missions are in the range 500 to 5000 volts, the highest voltage yet flown is approximately 100 volts. The NASCAP/LEO code is being developed to embody the phenomenology needed to model the environmental interactions of high voltage spacecraft. Some plasma environment are discussed. The treatment of the surface conductivity associated with emitted electrons and some simulations by NASCAP/LEO of ground based high voltage interaction experiments are described.

Mandell, M. J.↗
NASA NTRS2006

Space Environment Effects on Materials : An Overview

A general overview on the space environment and its effects on materials is presented. The topics include: 1) Impact of Space Effects on Spacecraft Costs; 2) Space Environment Effects on Spacecraft by Source; 3) Primary Source of Space Effects: The Sun; 4) The Earth's Environment; 5) Trapped Radiation Belts; 6) Aurora Are Everywhere; 7) Spacecraft Interactions; 8) Atmospheric Effects; 9) Contaminant Effects on Materials; 10) Meteoroid/Debris Effects on Materials; 11) Spacecraft Surface Charging; 12) Surface Discharge Effects; 13) Internal Electrostatic Discharge--Satellite Killer; 14) Plasma Interactions DS-1 Ion Engines; 15) Radiation Effects on Spacecraft Systems and Materials; 16) Total Ionizing Dose Effects Total Ionizing Dose Effects; 17) Man-Made Sources of Space Effects Man-Made Sources of Space Effects; and 18) Space Environments Versus Interactions.

charged particles↗
NASA NTRS1996

Electromagnetic radiation generated by arcing in low density plasma

An unavoidable step in the process of space exploration is to use high-power, very large spacecraft launched into Earth orbit. Obviously, the spacecraft will need powerful energy sources. Previous experience has shown that electrical discharges occur on the surfaces of a high-voltage array, and these discharges (arcs) are undesirable in many respects. Moreover, any high voltage conductor will interact with the surrounding plasma, and that interaction may result in electrical discharges between the conductor and plasma (or between two conductors with different potentials, for example, during docking and extravehicular activity). One very important aspect is the generation of electromagnetic radiation by arcing. To prevent the negative influence of electromagnetic noise on the operation of spacecraft systems, it seems necessary to determine the spectra and absolute levels of the radiation, and to determine limitations on the solar array bias voltage that depend on the parameters of LEO plasma and the technical requirements of the spacecraft equipment. This report describes the results of an experimental study and computer simulation of the electromagnetic radiation generated by arcing on spacecraft surfaces. A large set of high quality data was obtained during the Solar Array Module Plasma Interaction Experiment (SAMPIE, flight STS-62) and ground test. These data include the amplitudes of current, pulse forms, duration of each arc, and spectra of plasma waves. A theoretical explanation of the observed features is presented in this report too. The elaborated model allows us to determine the parameters of the electromagnetic noise for different frequency ranges, distances from the arcing site, and distinct kinds of plasma waves.

Vayner, Boris V.↗
DOE OSTI2024

Neutron and photon in-vivo materials characterization at the evolving plasma-material interface in plasma-burning fusion environments

This report includes the first set of MOSS data collected in the context of fusion-relevant plasma-material interactions. The data collected show that the surface curvature and stress irreversibly change during low-energy deuterium ion irradiation. This holds for both tungsten thin films, bulk tungsten, and single-crystal silicon. Meanwhile, argon irradiation did not produce this same effect. The surface morphology of the exposed samples was virtually identical regardless of gas species. There were, however, some surface chemistry differences between argon-exposed and deuterium-exposed samples, mainly concerning the oxide states of the W4f XPS signal. The changes in surface chemistry could be due to hydrogen dynamics on the tungsten surfaces, though further investigation will be required with in-situ irradiation and analysis. The changes in surface stress could also not be explained by temperature alone, as the temperature reached during the ion irradiations was too low to induce non-elastic strain. With this in mind, deuterium retention in the materials could change the surface curvature and stress. To confirm this, further work will be needed to quantify the change in curvature and relate it to ion flux, fluence, and deuterium retention. Unfortunately, when this work was conducted, the experimental setup for thermal desorption spectroscopy was not operating correctly, and that work could not be included in this dissertation. Despite experimental difficulties, this work shows the first results of a promising technique to study deuterium dynamics in tungsten-based reconstituted thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Amorphization and siliconization of silicon carbide as a first wall material

The understanding and prediction of silicon carbide (SiC) material evolution exposed to SOL plasma conditions is of prime interest because SiC represents a promising main chamber wall plasma-facing material for next-step fusion devices (low hydrogenic diffusion, good mechanical and thermal properties under neutron irradiation). Gross and net Si erosion rates from SiC surfaces in contact with a well-diagnosed L-mode plasma in the DIII-D tokamak have been simulated and the surface concentrations of impurities have been tracked as a function of time. Coupled simulation of surface model and impurity transport demonstrates amorphization of crystalline SiC exposed to L-mode plasma due to the accumulation of displacement damages under ion irradiation. This affects the lifetime of SiC plasma facing components. Surface evolution is tightly coupled to impurity transport in the plasma and therefore needs to be integrated with impurity transport simulations to effectively predict Si erosion rates and sub-surface concentrations as a function of time. The simulation workflow couples a semi-analytical surface model to the impurity transport code GITR. The surface model is a homogeneous mixed-material model that tracks physical & chemical sputtering and reflection of impurities. Gross erosion is primarily influenced by the background plasma parameters and redeposition patterns are mainly influenced by the prompt redeposition due to the gyro-orbits of impurity ions. Although crystalline form of SiC is preferable for fusion wall applications because of resistance to neutron irradiation, this work indicates that crystalline SiC will undergo amorphization under D plasma contact with implications of higher sputtering and fuel retention. These results direct us to explore the effects of amorphization on crystalline SiC and further the physics basis of SiC usage as first wall material for fusion environments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1985

Three-dimensional calculation of shuttle charging in polar orbit

The charged particles environment in polar orbit can be of sufficient intensity to cause spacecraft charging. In order to gain a quantitative understanding of such effects, the Air Force is developing POLAR, a computer code which simulates in three dimensions the electrical interaction of large space vehicles with the polar ionospheric plasma. It models the physical processes of wake generation, ambient ion collection, precipitating auroral electron fluxes, and surface interactions, including secondary electron generation and backscattering, which lead to vehicle charging. These processes may be followed dynamically on a subsecond timescale so that the rapid passage through intense auroral arcs can be simulated. POLAR models the ambient plasma as isotropic Maxwellian electrons and ions (0+, H+), and allows for simultaneous precipitation of power-law, energetic Maxwellian, and accelerated Gaussian distributions of electrons. Magnetic field effects will be modeled in POLAR but are currently ignored.

Cooke, D. L.↗
DOE OSTI2021

RF sheath induced sputtering on Proto-MPEX part 2: Impurity transport modeling and experimental comparison

The Prototype Material Plasma Exposure eXperiment (Proto-MPEX) is a pulsed linear plasma device that uses a radio frequency (RF) helicon antenna and a helicon ceramic window as the plasma ionization source. Modeling performed within this work on the helicon operations predicts hot spots on the helicon ceramic window due to an RF-induced sheath. The RF sheath potential leads to physical sputtering of the ceramic window predominantly where the helicon antenna sits around the helicon window. The role of oxygen in sputtering within Proto-MPEX is also investigated and is needed to match the experimental data. Experiments on Proto-MPEX show reasonable agreement with the modeled erosion/redeposition pattern on the helicon window, and the modeled impurity flux to the target shows radial transport within the device as expected from classical collisional impurity transport. Temperature screening of impurities is shown to be needed for Proto-MPEX to reduce impurity flux to the target. The modeling approach used in this work can be applied to other plasma RF applications for the determination of impurity production and transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

The 2020 plasma catalysis roadmap

Abstract Plasma catalysis is gaining increasing interest for various gas conversion applications, such as CO 2 conversion into value-added chemicals and fuels, CH 4 activation into hydrogen, higher hydrocarbons or oxygenates, and NH 3 synthesis. Other applications are already more established, such as for air pollution control, e.g. volatile organic compound remediation, particulate matter and NO x removal. In addition, plasma is also very promising for catalyst synthesis and treatment. Plasma catalysis clearly has benefits over ‘conventional’ catalysis, as outlined in the Introduction. However, a better insight into the underlying physical and chemical processes is crucial. This can be obtained by experiments applying diagnostics, studying both the chemical processes at the catalyst surface and the physicochemical mechanisms of plasma-catalyst interactions, as well as by computer modeling. The key challenge is to design cost-effective, highly active and stable catalysts tailored to the plasma environment. Therefore, insight from thermal catalysis as well as electro- and photocatalysis is crucial. All these aspects are covered in this Roadmap paper, written by specialists in their field, presenting the state-of-the-art, the current and future challenges, as well as the advances in science and technology needed to meet these challenges.

Bogaerts, Annemie (ORCID:0000000198756460)↗
DOE OSTI2021

Infrared Light-Emitting Devices from Antenna-Coupled Luttinger Liquid Plasmons In Carbon Nanotubes

Electrically driven light-emitting devices provide highly energy-efficient lighting at visible wavelengths, and they have transformed photonic and electronic lighting applications. Efficient infrared light-emitting devices, however, have been challenging because band gap emission from semiconductors becomes inefficient in the mid-infrared to far-infrared spectral range. Here, in this paper, we investigate infrared light-emitting devices (IRLEDs) based on Luttinger liquid (LL) plasmons in one-dimensional (1D) metallic carbon nanotubes. Elementary excitations in LL are characterized by collective charge and spin excitations, i.e., plasmons and spinons. Consequently, electrons injected into the nanotubes transform efficiently into LL plasmons, a hybrid excitation of electromagnetic fields and electrons. We design nanoantennas coupled to the carbon nanotube to radiate LL plasmons into the far field. LL-based IRLEDs can be designed to selectively emit at wavelengths across the far- and mid-infrared spectra. An electrical-to-optical power conversion efficiency up to 3.2% may be achieved. Such efficient and narrowband LL-based IRLEDs can enable novel infrared nanophotonic applications.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Thrust for interorbital propulsion - A question of lifetime

The most promising operational window for the use of magnetoplasmadynamic (MPD) thrusters is identified to be at megawatt power levels for orbital maneuvering. For such applications, the operation of a steady-state MPD thruster system imposes stringent requirements on the lifetime of thruster surfaces which will erode due to interactions with the plasma working fluid. Basic erosion mechanisms are presented and the problems associated with measuring the erosion rates are discussed. An experimental approach that would allow the development of a phenomenological model for erosion is proposed.

Gabriel, S. B.↗
NASA NTRS1990

Current limiting mechanisms in electron and ion beam experiments

The emission and collection of current from satellites or rockets in the ionosphere is a process which, at equilibrium, requires a balance between inward and outward currents. In most active experiments in the ionosphere and magnetosphere, the emitted current exceeds the integrated thermal current by one or more orders of magnitude. The system response is typically for the emitted current to be limited by processes such as differential charging of insulating surfaces, interactions between an emitted beam and the local plasma, and interactions between the beam and local neutral gas. These current limiting mechanisms have been illustrated for 20 years in sounding rocket and satellite experiments, which are reviewed here. Detailed presentations of the Spacecraft Charging at High Altitude (SCATHA) electron and ion gun experiments are used to demonstrate the general range of observed phenomena.

Olsen, R. C.↗
DOE OSTI2022

HIDRA-MAT liquid metal droplet injector for liquid metal applications in HIDRA

A liquid metal droplet injector was explicitly designed for the Hybrid Illinois Device for Research and Applications Material Analysis Test-stand (HIDRA-MAT) at the University of Illinois Urbana-Champaign to prepare liquid metal plasma-facing components (PFCs) for plasma exposure. The design goals were to create a compact, reliable, and robust design that could apply liquid metal droplets in-vacuo to a variety of samples. The injector was designed for liquid metal use, and results discussed pertain to lithium. The injector can produce lithium droplets of consistent size by utilizing programmable piston movement. Here, droplet formation data is presented for four different piston step sizes (0.125 mm, 0.25 mm, 0.5 mm, and 1 mm) at three different nozzle temperatures (185 °C, 230 °C, and 270 °C). Droplets are formed on the injector nozzle tip and a linear shift mechanism vertically translates the droplet to the substrate for application. This design prevents the droplet from inadvertently detaching off the nozzle and falling to the sample. Application of the liquid metal droplet ensures placement consistency on the substrate and helps avoid damage to components in HIDRA-MAT that should not interact with liquid metals. A description of the liquid lithium droplet creation and application results is given and provides additional insight into the cooling and oxidation of lithium droplets under vacuum conditions. A second nozzle was fabricated and demonstrated repeatability in droplet diameter creation having a variance of ±0.14 mm for droplets created from the same number of piston steps. The end-use for the injector on HIDRA-MAT is to apply liquid metals to PFCs and expose them to HIDRA's plasma with subsequent intershot in-vacuo surface analysis in HIDRA-MAT for plasma-material interaction studies.

42 ENGINEERING↗