Search NASA⌕ Search

SEARCH · Search NASA

Results for “Subsequent Fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

214 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

ATF Cladding Mechanical Properties Report: Capability Demonstration

This report documents mechanical testing capability demonstration activities performed in fiscal year (FY)2025 at Oak Ridge National Laboratory(ORNL)on chromium-coated (Cr-coated) and uncoated advanced zirconium alloy claddings irradiated in the High Flux Isotope Reactor (HFIR) to approximately 4 displacements per atom (dpa), corresponding to ~13GWd/t burnup. Specimens were prepared in axial tension (ATT) and ring tension (RTT) geometries, and passive silicon carbide(SiC)thermometry (TM) was employed to determine irradiation temperatures, which averaged 38–43 °C below the 330 °C design target. Mechanical testing at ambient temperature demonstrated the expected irradiation-induced hardening, with yield strength(YS)and ultimate tensile strength(UTS)values increasing substantially relative to unirradiated counterparts. However, this strengthening was accompanied by a reduction in ductility, as indicated by lower uniform and total elongations(UE and TE). Both coated and uncoated claddings exhibited similar mechanical response, though Cr-coated specimens showed surface cracking perpendicular to the loading direction, attributable to the hardness mismatch between the coating and substrate. Fracture in all cases remained ductile, and no coating spallation was observed following HFIR irradiation. Complementary efforts were directed toward the fabrication of test specimens from commercially irradiated cladding (rod 47I, ~31.1 GWd/t average burnup). Axial sectioning and computer numerical control(CNC)machining successfully produced ATT geometries suitable for benchmarking against HFIR-irradiated specimens. This capability enables direct comparison of cladding behavior between test reactor and commercial reactor environments, thereby supporting the validation of HFIR as a surrogate irradiation platform for accident tolerant fuel (ATF) development. Once HFIR irradiations are completed in FY26,the relevant comparison tests will be completed. Collectively, the FY 2025 PIE campaign has provided mechanical performance data for irradiated advanced claddings The demonstrated capabilities support the framework for mechanical testing and further evaluations in subsequent years. These efforts will represent an important contribution toward the licensing and deployment of Cr-coated zirconium alloy cladding as a near-term ATF solution.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Strain energy density and surface layer energy for a crack-like ellipse

Some of the fundamental concepts of sharp crack fracture criteria are applied to cracks and narrow ellipses. The strain energy density theory is extended to notch boundaries, where the energy in a surface layer is calculated and the location of failure initiation is determined. The concept of a core region near the notch tip, and its consequences, are examined in detail. The example treated is that of an elliptical cavity loaded uniformly at a large distance from the hole, and at an angle to the hole; the results are shown to approach that of the crack solution for narrow ellipses, and to display quite satisfactory agreement with recently published experimental data under both tensile and compressive loading conditions. Results also indicate that in globally unstable configurations in brittle materials, the original loading and notch geometry are sufficient to predict the subsequent crack trajectory with considerable accuracy.

Kipp, M. E.↗
NASA NTRS2001

Delayed Alumina Scale Spallation on Rene'n5+y: Moisture Effects and Acoustic Emission

The single crystal superalloy Rene'N5 (with or without Y-doping and hydrogen annealing) was cyclically oxidized at 1150 C for 1000 hours. After considerable scale growth (>= 500 hours), even the adherent alumina scales formed on Y-doped samples exhibited delayed interfacial spallation during subsequent water immersion tests, performed up to one year after oxidation. Spallation was characterized by weight loss, the amount of spalled area, and acoustic emission response. Hydrogen annealing (prior to oxidation) reduced spallation both before and after immersion, but without measurably reducing the bulk sulfur content of the Y-doped alloys. The duration and frequency of sequential, co-located acoustic emission events implied an interfacial crack growth rate at least 10(exp -3) m/s, but possibly higher than 10(exp 2) m/s. This is much greater than classic moisture-assisted slow crack growth rates in bulk alumina (10(exp -6) to 10(exp -3) m/s), which may still have occurred undetected by acoustic emission. An alternative failure sequence is proposed: an incubation process for preferential moisture ingress leads to a local decrease in interfacial toughness, thus allowing fast fracture driven by stored strain energy.

Smialek, James L.↗
NASA NTRS2000

The Geologic History of Mars: An Astrobiology Perspective

Fourteen SNC meteorites contain information which must be incorporated with recent spaceflight data for developing Mars' geologic history. SNCs have crystallization ages of 4500 to 160 m.y. Tle oldest meteorite ALH84001 contains information on the Noachian period of Mars' history. There are no meteorites from the Hesperian period and the remaining 13 meteorites fall into two age groups within the Amazonian: The nakhlites around 1300 m.y. and the shergottites between 800-160 m.y. Oxygen isotopic analysis of Martian samples shows two distinct O2 reservoirs throughout Martian history indicating late additions of volatiles and a lack of plate tectonics prior to 3.9 Gy. Evidence for percolation of aqueous brines through impact-produced fractures in the rocky surface is contained in the 3.9 Gy-old ALH84001 carbonate deposits. These carbonates precipitated at approx. 100 C. At this time life had already evolved on Earth. Early Mars could have hosted life similar to the bacteria that inhabited early Earth. Potential microorganisms could have been transported into fractures by carbonate-bearing waters and their remains could have become incorporated into the precipitated carbonate. Since Mars had a weak magnetic field at this time, it can be hypothesized that some of the Martian microorganisms may have been similar to terrestrial magnetotactic bacteria. Over geologic time episodic cratering, and tectonic events have occurred on Mars along with the periodic release of subsurface waters which may have produced clays within SNC meteorites. The geochemical data contained within SNC meteorites complements previous observational data and the recent Mars Global Surveyor data to provide a geological and environmental history which spans almost the entire lifespan on Mars. One of the outstanding features of this model is the possible creation of an early (about 4 Gy) volatile reservoir distinct from the outgassed Mars volatiles, and the persistence of this reservoir throughout most, if not all of subsequent Mars' history. Within the framework of this history a potential scenario for a possible record of living organisms is provided by suggestive structures and organic signatures trapped within secondary mineral deposits and alteration features of some SNC meteorites. Tracing the differences in oxygen isotopic compositions within Martian components allows us to gain insight in the history of Mars.

Gibson, Everett K.↗
NASA NTRSDate not supplied

Recent Advances in Discrete Crack Modeling Applied to Laminated Composites with Emphasis on: Floating Node Method, VCCT and Cohesive Zone Modeling

The present talk will provide an overview of the work performed during the Advanced Composites Project (ACP) on the development, and verification and validation of the Floating Node Method (FNM) as well as the Virtual Crack Closure Technique (VCCT) and cohesive zone modeling (CZM). The FNM is a finite element-based technique to represent crack networks. The complex nature of matrix crack-delamination interactions observed in unidirectional (UD) tape laminates suggests that a methodology such as the FNM method may be required to be able to accurately simulate damage progression in these laminates. Simulating crack onset and growth within the context of the FNM relies on techniques such as VCCT and CZM. The talk is organized to provide, via select examples, an overview of the breadth of the Verification & Validation (V&V) exercises performed during the ACP, and how these challenged the state-of-the art and guided further developments in discrete crack modeling, while helping to establish confidence in the progress made and map the challenges ahead. The performance of the VCCT and CZM individually, and in combination with the FNM can be assessed through verification exercises. These exercises typically consist of a comparison of simulation results to known numerical or analytical solutions. Verification is key to identify implementation issues and limitations that, otherwise, may remain undetected and cloud any subsequent validation efforts. Indeed, a subset of these numerical exercises led to further developments of the VCCT and the FNM method as will be illustrated. Before embarking on the subsequent validation of the framework, it is critical to have adequate characterization data. However, the testing campaign conducted revealed material responses that challenged the state-of-the-art and required further developments. The developments in CZM technology associated with the modeling of the responses of hybrid interfaces (fabric/UD) will be given as an example. Finally, the talk will conclude with a summary of the validation exercises performed under quasi-static and fatigue loadings, highlighting some of the key achievements, outstanding challenges and lessons learned.

finite elements↗
DOE OSTI2025

Physics-Based Limiter Redesign and Bit Performance Analysis at The Geysers

As part of a U.S. DOE Geothermal Technologies Office funding opportunity, Geysers Power Company, LLC (GPC), an indirect subsidiary of Calpine Corporation, partnered with Sandia National Labs, EGI at the University of Utah, and Texas A&M University to demonstrate increased drilling performance at The Geysers Geothermal Field. The performance target in the drilling demonstrations is at least a 25% improvement in rates of penetration, with increased footage on bottom for each bit coupled with increased bit life and time drilling. The project leverages advances in oil and gas drilling technologies including PDC bits, along with the physics-based limiter redesign techniques championed in drilling demonstrations conducted at the Utah FORGE geothermal site. The planned drilling demonstrations are being conducted as part of an existing drilling campaign intended to enhance reservoir utilization. The wells are typically drilled to the top of the reservoir with mud and then air-drilled to total depth (TD) through fractured zones at temperatures ≥ 450°F. A major goal of the project is to assess the effectiveness of implementing mechanical specific energy (MSE) and drilling dysfunction diagnosis and remediation in these challenging environments, as well as alternate rock reduction technologies. The first demonstration well has been completed, with 15 PDC bit runs in the 17.5”, 12.25” and 8.5” sections. Initial analysis shows ROP gains in all three sections, especially in the 17.5” and 12.25” sections, compared with conventional roller cone bit runs in the demonstration well and offset wells. However, in the 8.5” hole, wear and damage to the PDC bits resulted in relatively short bit runs. Analysis is underway to take advantage of the positive results and remediate the challenges. This paper provides updates on drilling activities conducted since the Phase 1 demonstration well at GDC-36 which was drilled from November 2023-January 2024. Additional analysis of the bit performance has been conducted. Furthermore, in subsequent wells drilled by GPC, PDC bits have been used extensively, building on the gains realized at GDC-36. GPC has continued to work with bit vendors to identify designs that last longer in the harsh, air-drilled 8.5” portions of the wells. Planning for the Phase 2 demonstration at Prati-44 is ongoing.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Assessment of buffer-IPyC thermomechanical debonding behavior using new experimental strength data in BISON

TRIstructural ISOtropic (TRISO) fuel is a nuclear fuel commonly used in High Temperature Gas-cooled Reactors (HTGRs). A single sub-millimeter-diameter TRISO fuel particle consists of a spherical fuel kernel surrounded by four coating layers: a low-density pyrocarbon buffer layer, an inner pyrolytic carbon (IPyC) layer, a silicon carbide (SiC) layer, and an outer pyrolytic carbon (OPyC) layer. The kernel is commonly made of UO2 or a mixture of uranium carbide and uranium oxide (UCO). During reactor operation, the TRISO coating layers are subjected to irradiation-induced dimensional changes and the associated thermomechanical behavior of each layer. One of the observed behaviors is gap formation between the buffer and IPyC layer due to the porous buffer’s irradiation-induced shrinkage exceeding that of the IPyC layer. Not all irradiated particles will experience buffer-IPyC gap formation. The debonding may be partial, or it may be nearly total. However, from post-irradiation examination of UCO TRISO fuels irradiated as part of the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program, it was concluded that partial buffer-IPyC debonding was the most common type of buffer-IPyC interaction. To predict TRISO thermomechanical performance, multi-physics models have been built that are being continually updated and refined. The BISON code is a finite element-based nuclear fuel performance code that may be used for 1D, 2D, and 3D TRISO particle simulations. This code is used to calculate fuel temperature, kernel swelling, buffer densification, thermal and irradiation creep, fracture, and fission gas production and release. One of the recent additions to the BISON code is the ability to model the process of layer debonding. This paper will focus on the simulation results of the improved BISON debonding model that will utilize updated strengths measured from irradiated AGR TRISO fuel particles. The new experimental strength data from micromechanical tests of irradiated TRISO fuel samples were exercised in the BISON simulations and compared to baseline strength data to assess their applicability in the models. This also includes updated buffer-IPyC bond strengths to simulate layer delamination. Based on current experimental observations it is noted that the buffer-IPyC separation occurs not exactly at the junction of these two layers, but more on the side of the buffer layer. That observation is also implemented in the TRISO interface debonding model. This improved modeling approach using experimental strength data to characterize buffer-IPyC debonding and its potential subsequent cracking will be presented in the paper along with comparisons to available experimental observations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2002

Impact Cratering Calculations

Many Martian craters are surrounded by ejecta blankets which appear to have been fluidized forming lobate and layered deposits terminated by one or more continuous distal scarps, or ramparts. One of the first hypotheses for the formation of so-called rampart ejecta features was shock-melting of subsurface ice, entrainment of liquid water into the ejecta blanket, and subsequent fluidized flow. Our work quantifies this concept. Rampart ejecta found on all but the youngest volcanic and polar regions, and the different rampart ejecta morphologies are correlated with crater size and terrain. In addition, the minimum diameter of craters with rampart features decreases with increasing latitude indicating that ice laden crust resides closer to the surface as one goes poleward on Mars. Our second goal in was to determine what strength model(s) reproduce the faults and complex features found in large scale gravity driven craters. Collapse features found in large scale craters require that the rock strength weaken as a result of the shock processing of rock and the later cratering shear flows. In addition to the presence of molten silicate in the intensely shocked region, the presence of water, either ambient, or the result of shock melting of ice weakens rock. There are several other mechanisms for the reduction of strength in geologic materials including dynamic tensile and shear induced fracturing. Fracturing is a mechanism for large reductions in strength. We found that by incorporating damage into the models that we could in a single integrated impact calculation, starting in the atmosphere produce final crater profiles having the major features found in the field measurements (central uplifts, inner ring, terracing and faulting). This was accomplished with undamaged surface strengths (0.1 GPa) and in depth strengths (1.0 GPa).

Ahrens, Thomas J.↗
NASA NTRS2019

Improved Processing Techniques for Inclusion-Free Steel for Bearing and Mechanical Component Applications

High hardness, high carbide powder metallurgy tools steels such as M62 enable the operation of ball bearings at extremely high load and stress levels. Operation under such conditions increases the potential for rolling contact fatigue failure attributed to ceramic particle inclusions. To address this challenge, industry has sought steel made from ever increasing levels of cleanliness but the results have been uneven owing to the random nature of the occurrence of material flaws. One common approach is to rely upon careful ingot inspections prior to bearing manufacture. By selecting the cleanest portion of an ingot, it is expected that bearings relatively free from material flaws will result. This approach is not always successful because detrimental flaws that exist deep within an ingot can pass inspection undetected potentially causing subsequent failure. Recent efforts to commercialize an intermetallic material, 60NiTi, for rolling element bearings demonstrates a pathway to produce bearing steel that is free from unwanted ceramic particle inclusions. In this paper, the process used to make bearing grade ceramic-free NiTi alloys is described and applied to steelmaking. At its core, the NiTi process differs from steel making in one key aspect. NiTi alloys are made from elementally pure starting materials that are melted, blended and processed in equipment absolutely free from exposure to oxygen and ceramics ensuring a ceramic particle-free product. In contrast, the predominant method to make bearing steel is to employ a successive series of purification steps to reduce contamination levels below required thresholds. This paper describes the processes developed and applied to high carbide tool steel, M62. The resulting material and microstructures are evaluated and compared to M62 prepared by conventional powder metallurgy techniques. It is hoped that the application of materials manufacturing techniques used for fracture sensitive ceramics and intermetallic materials like NiTi can provide a pathway to Ultra-Clean, Ceramic-Inclusion free steels for rolling element bearings and other failure critical applications.

Steel↗
NASA NTRS1993

Giant radiating dyke swarms on Earth and Venus

On Earth, giant radiating dyke swarms are usually preserved as fan-shaped fragments which have been dismembered from their original configuration by subsequent plate tectonic rifting events. Analysis of the largest fragments and consideration of their original configuration has led to the idea that many swarms are plume related, and that dyke swarms radiate away from plume centers. Magellan radar data reveal abundant intact giant radiating swarms on Venus which are similar in scale and pattern to those on Earth. The absence of intense weathering and plate tectonic processes on Venus accounts for the preservation of the primary radiating patterns. It is characteristic of both Earth and Venus that giant radiating dikes are emplaced laterally for distances of at least 2000 km away from plume centers. At distances beyond the influence of the plume on both Earth and Venus, the radiating dyke pattern is often swept into a linear pattern aligned with the regional stress field. There is tremendous potential synergism between the characterization and analysis of terrestrial dyke swarms (where significant erosion has revealed their structure and emplacement directions at depth) and the giant swarms of Venus (where the complete circumferential structure is preserved, and the surface fracture systems above near surface dikes and the nature of the central source regions are revealed). In this study, we report on the characteristics of radial dyke swarms on Earth and Venus and draw some preliminary comparisons from the two perspectives. In summary, on both planets there is evidence for plume-related magmatic centers associated with vertical and lateral injection of magma over considerable distances (up to at least 2000 km). The abundance of very broadly radiating swarms on Venus supports the notion that the swarms on Earth were radiating over broad sectors at the time of intrusion but were dissected by later events. The Venus data show that a swarm can change from radiating (proximal) to regional (distal) subparallel orientations. An implication for Earth is that many regional linear swarms which do not have a radiating pattern may be due to fragmentation of the swarm during later plate tectonic rifting. Completion of the global classification and census of Venus features, comparison to the terrestrial synthesis, and documentation of the mode of emplacement of dikes in these environments (buffered and unbuffered conditions) should lead to additional general insight into mechanisms of formation and evolution and their relation to plumes.

Ernst, Richard E.↗
NASA NTRS1994

Scaling of impact damage in fiber composites

Impact damage in fiber composite structures remains of much concern, and is often the limiting factor in establishing allowable strain levels. The complexity of impact damage formation usually dictates that experiments are required, but scaling of results from small laboratory scale specimens to large structures introduces additional uncertainty into the analysis. This presentation gives the results of an analytical and experimental investigation intended to develop procedures for prediction of damage formation and subsequent strength loss, with particular emphasis on scaling of results with respect to structure size. The experimental investigation involved both drop-weight and airgun impact on carbon/epoxy plates and cylinders. Five sizes of plates ranging from 50 by 50 by 1.072 mm to 250 by 250 by 5.36 mm, and two sizes of cylinders with diameters of 96.5 and 319 mm, were employed in the experimental program. Impact tests were carried out over a range of impact conditions, and specimens were inspected for damage by C-scan and deplying. Analysis procedures were developed for both quasistatic and dynamic impacts for both the plates and cylinders. As has been reported previously, comparison of predicted structural response and measured surface strains was quite good over the entire range of sizes employed in the program. The damage formation and strength loss after impact showed a number of interesting features that are significant with respect to scaling of size. The extent of delamination was observed to increase with specimen size more than would be expected if stresses controlled the delamination extent. This was explained on the basis that delamination is controlled by energy release rates, and thus incorporates the usual dependence on the absolute size characteristic of fracture mechanics. Additionally, the experiments indicated that delamination initiated at matrix cracks and is dependent on the absolute size of the ply group thicknesses. Both the initiation and propagation of delamination are seen to be controlled by fracture mechanics parameters, and thus show specific dependence on size that must be accounted for in extrapolating results from laboratory scale tests to full size structures.

Swanson, Stephen R.↗
DOE OSTI2026

Influence of Powder Characteristics and Processing Methods on Creep Performance of Powder Metallurgy Hot Isostatic Pressed SS316

The U.S. nuclear energy expansion goals are driving the demand for manufacturing routes that can rapidly produce large, complex, near net shape components. Powder metallurgy hot isostatic pressing (PM HIP) is an advanced manufacturing technique that can be economically scaled-up, while alleviating the supply chain challenges that forging and casting face in terms of cost and lead time constraints. This makes PM-HIP a viable technology to aid and accelerate large-scale part manufacturing for nuclear applications. However, large-scale qualification and deployment of this technology require a thorough understanding of the influence of powder feedstock quality, powder handling history, hot isostatic pressing (HIP) parameters, and subsequent heat treatment on microstructural evolution and elevated temperature mechanical performance. The present work focusses on 316 austenitic stainless steel (SS316) which is most commonly used in high temperature environments for nuclear applications Results from this study show that PM HIPed SS316 meets ASME tensile requirements at room temperature and at elevated temperature. However, creep performance of PM-HIPed SS316 remains inferior to its wrought counterpart, demonstrating that tensile performance alone is not a reliable metric for long duration high temperature integrity. Further, this report delineates powder derived microstructural features that govern creep damage, with key evidences pointing to “microstructural inheritance” from gas atomized powder feedstocks. Commercial SS316 powders of varying chemical compositions and recycling histories were studies, and the results showed large differences in elemental segregation, oxide surface layers and secondary phase distributions. Multi-scale characterization revealed segregation of chromium, molybdenum, manganese and silicon at the boundaries and the precipitation of manganese-, silicon-, and molybdenum-oxides. During HIP consolidation, these surface oxides transform into decorated prior particle boundaries (PPBs) and grain boundary inclusions that persist through conventional post-HIP solution annealing treatment. The retained oxides in post-HIP microstructures were found to influence grain growth, precipitation behavior, and ultimately creep cavitation and fracture. Such post-HIP heat treatments are therefore limited by a complex trade-off between grain growth, and oxide coarsening which aggravate creep damage by acting as nucleation sites for cavities. The objective of this work is to establish an integrated processing–structure–property framework for PM-HIP 316 stainless steel by investigating the influence of powder feedstock characteristics in pre- and post-HIP processing as well as to understand the significance of post-HIP heat treatment on microstructural evolution and creep properties. The results from this report emphasize the significance of powder feedstock integrity in improving creep performance of PM-HIPed SS316, by highlight the effect of rapid solidification, elemental segregation, oxide formation and powder recycling on microstructural defect inheritance following HIP consolidation. Rather than considering HIP processing, solution annealing, and mechanical performance independently, this report treats powder production, HIP consolidation, post-HIP thermal processing, and creep deformation as interconnected stages within a continuous metallurgical process. The resulting framework will provide a scientific basis for developing feedstock engineering strategies capable of improving long-term reliability of PM-HIP stainless steels and accelerating their qualification for advanced nuclear applications.

Ajjarapu, Pavan [Oak Ridge National Laboratory (OR↗
NASA NTRS1999

Carbon Fiber Reinforced/Silicon Carbide Turbine Blisk Testing in the SIMPLEX Turbopump

A program designed to implement a ceramic matrix composite integrally bladed disk (blisk) into rocket engine style turbomachinery has successfully completed testing. The Marshall Space Flight Center (MSFC) program, utilizing the MSFC turbomachinery design, analysis, and testing capabilities along with materials development capabilities from both Glenn Research Center (GRC) and MSFC, has tested two carbon fiber reinforced silicon carbide blisks in the Simplex Turbopump at MSFC's Test Stand 500. One blisk contained a polar woven fiber preform, while the second blisk tested utilized a quasi-isotropic preform. Vhile earlier papers have chronicled the program's design, material testing, and torque testing efforts, this paper focuses on the testing of the blisks in the Simplex turbopump. Emphasis will be placed on the actual condition of the blisks before and after the testing test program design methodology, and conclusions that can be drawn from the test data and blisk final conditions. The program performed three separate test series. The first series was needed to validate that the Simplex turbopump was correctly re-built following a major incident to the turbopump. The turbopump had two major differences from the original design. The most obvious difference was the sleeve required throughout the bore of the main housing. The second major difference was modifications to the pump diffuser to improve performance. Several areas were burnt during the incident and were either repaired by weld repair (pump inlet housing) or simply smoothed out (turbine nozzle discharge). The test series was designed to weed out any turbopump design and manufacturing flaws or fatigue issues prior to putting the C/SiC blisks into it. The second and third series were the C/SiC blisk test series. The primary goal of these series was to expose the blisks to as much fatigue causing dynamic stress as possible to examine the material's capability. Initially, the test plan was to put equal time on the two blisks, however, as the test series progressed, the funding allowed additional testing to occur. The additional test time was placed on the polar weave blisk. The total test time accrued on the polar blisk was 2550 seconds with 860 seconds near the turbopump design speed of 25,000 rpm. This testing included 6 tests / 775 seconds pumping liquid nitrogen and 7 tests / 1775 seconds pumping liquid oxygen. The drive gas for all of the tests was gaseous nitrogen due to the lack of hot gas source for the Simplex turbopump. The quasi-isotropic blisk was tested for XX total tests and XXXX seconds with X tests/XXXX seconds pumping liquid nitrogen and X tests/XXXX seconds pumping liquid \oxygen.During the test series, the blisks were inspected following each test. Inspections initially were viewed from the downstream side of the blisks only. Midway through the testing, a method of borescoping the leading edges of the blades was devised, and subsequently, both sides of the blades were inspected following each test. The leading and trailing edges of the polar blisk held up better than the quasi-isotropic blisk. This was a known possibility due to the varying fiber direction in the blades as the rectangular preform weave is cut in a circular pattern. The surprising fact about the testing was that there was no measurable performance loss due to the inaccuracies in the blade manufacturing in the C/SiC blisks, the surface roughness C/SiC of the blades, or the loss of the material in the polar blisk. A performance shift was seen in the quasi-isotropic blisk as portions of the leading and trailing edges were lost. After the testing was completed, detailed inspections of the blisks were performed. The largest surprise was the polar blisk had a obvious crack in a single blade that was located nearly midspan which was not detected in test. The crack ran completely through the blade circumferenciary and through the radial length of the blade. However, the crack does not appear to extend into the blisk hub. Although the cause of the crack is still under investigation, the material appears to be tolerant of this crack, and other hairline cracks discovered under higher magnification. This bodies well for eventual use of this material in actual flight turbopumps where monolithic fracture toughness issues limit its use.

Genge, Gary G.↗
NASA NTRS2005

X-Aerogels for Structural Components and High Temperature Applications

Future NASA missions and space explorations rely on the use of materials that are strong ultra lightweight and able to withstand extreme temperatures. Aerogels are low density (0.01-0.5 g/cu cm) high porosity materials that contain a glass like structure formed through standard sol-gel chemistry. As a result of these structural properties, aerogels are excellent thermal insulators and are able to withstand temperatures in excess of l,000 C. The open structure of aerogels, however, renders these materials extremely fragile (fracturing at stress forces less than 0.5 N/sq cm). The goal of NASA Glenn Research Center is to increase the strength of these materials by templating polymers and metals onto the surface of an aerogel network facilitating the use of this material for practical applications such as structural components of space vehicles used in exploration. The work this past year focused on two areas; (1) the research and development of new templated aerogels materials and (2) process development for future manufacturing of structural components. Research and development occurred on the production and characterization of new templating materials onto the standard silica aerogel. Materials examined included polymers such as polyimides, fluorinated isocyanates and epoxies, and, metals such as silver, gold and platinum. The final properties indicated that the density of the material formed using an isocyanate is around 0.50 g/cc with a strength greater than that of steel and has low thermal conductivity. The process used to construct these materials is extremely time consuming and labor intensive. One aspect of the project involved investigating the feasibility of shortening the process time by preparing the aerogels in the templating solvent. Traditionally the polymerization used THF as the solvent and after several washes to remove any residual monomers and water, the solvent around the aerogels was changed to acetonitrile for the templating step. This process took a couple of days. It was experimentally determined that the polymerization reaction could be done in acetonitrile instead of THF with no detrimental effects to the properties of the resulting aerogel. Other changes in the time needed to crosslink the gels in the isocyanate solution as well as changes to the subsequent washing procedure could also shorten the processing time with no effect on the properties. Processing methods were also developed that allowed a variety of shapes as well as sizes of these materials to be formed.

Source record↗
NASA NTRS2013

The Komplast Experiment: Space Environmental Effects after 12 Years in LEO (and Counting)

The Komplast materials experiment was designed by the Khrunichev State Research and Production Space Center, together with other Russian scientific institutes, and has been carried out by Mission Control Moscow since 18. Komplast panels fitted with material samples and sensors were located on the International Space Station (ISS) Functional Cargo Block (FGB) module exterior surface. Within the framework of this experiment, the purpose was to study the effect of the low earth orbit (LEO) environment on exposed samples of various materials. The panels were sent into orbit with the FGB when it launched on November 20, 1998. Panels #2 and #10 were retrieved during Russian extravehicular activity in February 2011 and sealed within cases to temporarily protect the samples from exposure to air until they could be studied on the ground. Panel #2 contained an experiment to detect micrometeoroid and orbital debris (MMOD) impacts, radiation and UV sensors, several pieces of electrical cable, and samples made from elastomeric and fluoroplastic materials. Panel #10 contained a temperature sensor, and both carbon composite and adhesive-bonded samples. A figure shows the location of panels #2 and #10 on the FGB module aft endcone. The panels were subsequently returned to Earth by Space Shuttle Discovery on the STS-133/ULF-5 mission after 12 years of LEO exposure and opened in an argon chamber at the Institute of Nuclear Physics at Moscow State University in July 2011. Based on the results of analyzing the readings from sensors located on Komplast panels and in studying material samples from the panels, the comprehensive effect of spaceflight factors on the FGB (at the locations of Panels #2 and #10) was evaluated. Total solar exposure was determined to be 960 +/- 200 kJ/square cm or 21,000 equivalent solar hours. Because of location of these two panels and the ISS flight attitude, atomic oxygen (AO) fluence was relatively low for such a long duration exposure, approximately 1.5x10 (exp 21) O atoms/sq. cm. Most of the AO fluence occurred during the early phase of ISS assembly. Temperatures ranged from a maximum of 107 C to a minimum of -80 C. The MMOD environment was determined, as is shown. Interestingly, the distribution of craters and low-velocity impact particles observed in the 5-50 micron size range was approx 2-3 orders of magnitude higher than that predicted by the ORDEM2000 model of natural and artificial origin microparticles in the ISS orbit. Contamination observations were also made, through the evaluation of optical properties on thermal control coatings and by the examination of visible deposits located near several samples on the panels, primarily from elastomeric samples. These elastomer samples were extensively investigated for their physical property changes and sealing capability. In addition, 16 samples of adhesive-bonded joints using three types of epoxy adhesive were evaluated studying fracture toughness, failure surface, and adhesive volume properties. Both rubber and adhesive-bonded specimens also underwent additional (post-flight) ground-based exposures to simulate a total 30 years in LEO prior to their evaluation. Overall, results indicate that space environmental effects will not adversely impact the service life of the FGB through 2028. Our investigation is complete and a summary of the results obtained from this uniquely long-duration exposure experiment will be presented.

Shaevich, S. K.↗
NASA NTRS2014

A Novel Hybrid Ultramicrotomy/FIB-SEM Technique: Preparation of Serial Electron-Transparent Thin Sections of a Hayabusa Grain

The Japanese space agency's (JAXA) Hayabusa mission returned the first particulate samples (typically <100micron) from the surface of an asteroid (25143 Itokawa). These precious samples provide important insights into early Solar System processes, but their sizes pose tremendous challenges to coordinated analysis using a variety of nano- and micro-beam techniques. The ability to glean maximal information from individual particles has become increasingly important and depends critically on sample preparation. We developed a hybrid technique combining traditional ultramicrotomy with focused ion beam (FIB) techniques, allowing for more thorough in situ investigations of grain surfaces and interiors. Using this method, we increase the number of FIB-prepared sections that can be recovered from a particle with dimensions on the order of tens of microns. These sections can be subsequently analyzed using a variety of analytical techniques. Particle RA-QD02-0211 is a approx. 40×40×20 micron particle from Itokawa containing olivine and Fe sulfides. It was embedded in low viscosity epoxy and partly sectioned to a depth of approx 10 micron; sections are placed on Cu grids with thin amorphous films for transmission electron microscope (TEM) analyses. With the sample surface partly exposed, the epoxy bullet is trimmed to a height of approx. 5mm to accommodate the allowable dimensions for FIB work (FEI Quanta 600 3D dual beam FIB-SEM). Using a diamond trim knife, the epoxy surrounding the grain is removed on 3 sides (to within a few microns of the grain); the depth of material removed extends well below the bottom of the particle. The sample is attached to an SEM pin mount, the epoxy coated with conductive paint, and the entire assembly coated with approx. 40nm of carbon to eliminate sample charging during FIB work. A protective carbon cap is placed according to the plan for the 15 FIB sections. The central 'spine' of the cap runs perpendicular to the front of the sample, and the 'ribs' protruding from either side run parallel. Each rib indicates the location of a planned FIB section, and the spine contains the final two planned sections. We use a cap with a 4 micron-wide spine and 2micron-wide ribs that have ≳3.5 micron of space between them (narrower cuts result in too much re-deposition of material inside the trenches). Using a 30kV, 3nA ion-beam we expose the front surface of the grain and commence milling trenches between sections. Rather than using the typical C-cut to prepare the sample for lift-out, an L-cut is used instead, leaving the sample connected by an interior tab. tab. Sections are lifted out, attached to TEM grids and thinned to electron transparency. TEM analyses show that our hybrid technique preserves both interior and edge features, including surface modifications from exposure to the space environment, such as damaged rims that form in response to solar wind implantation effects and adhering grains. In addition, the FIB sections provide larger areas that are free of fractures and chatter effects in comparison to the microtome thin sections, thus enabling more accurate measurements of solar flare particle track densities that are used to determine the surface exposure age of the particles.

Berger, Eve L.↗