SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This is a poster presentation given at the 2024 AIChE Annual Meeting, San Diego, CA, October 27-31, 2024. In this poster we describe a scalable and solution-based strategy to prepare wafer-scale 2D amorphous carbon with thickness down to 1–2 atomic layers from coal-derived carbon quantum dots as precursors.
Large diameter, carbon-carbon composite, monofilaments were produced from the pyrolysis of organic precursor resins reinforced with high-strenght carbon fibers. The mechanical properties were measured before and after pyrolysis and the results were correlated with the properties of the constituents. The composite resulting from the combination of Thornel 75 and GW-173 resin precursor produced the highest tensile strength. The importance of matching strain-to-failure of fibers and matrix to obtain all the potential reinforcement of fibers is discussed. Methods are described to reduce, within the carbonaceous matrix, pyrolysis flaws which tend to reduce the composite strength. Preliminary studies are described which demonstrated the feasibility of fiber-matrix copyrolysis to alleviate matrix cracking and provide an improved matrix-fiber interfacial bonding.
Mesophase pitch and linear low-density polyethylene (LLDPE) were blended by shear mixing and extruded producing precursor fibers which were then converted to carbon fibers (CFs). LLDPE additives agglomerate within the isotropic spheres rather than uniformly dispersing throughout the entire matrix. The blends possess different thermal properties and precursor tensile properties evident by two-phase tensile stress nature not present in precursor fibers produced from pure pitch. The resultant CFs were oxidized at 280 °C for 4 h and carbonized at 1000 °C for 15 min. This process created pitch CFs with a tensile strength of 1.23 GPa and a Young’s modulus of 99 GPa. All CFs produced from blends of pitch and LLDPE possessed a tensile strength of 0.63 GPa and less. These CFs showed a microstructure slightly different from the pure pitch CFs with fractured CF cross sections revealing voids present in all blended CFs due to burnt off LLDPE stemming from carbonization. Further study into compatibilizers and new conversion processes is required to successfully blend LLDPE with mesophase pitch for the purpose of producing a new low-cost CF.
The practical application of CO2 conversion through electrochemical reduction is still hindered by the lack of high performance and cost-effective catalysts. It is thus imperative to explore feasible strategies for scalable fabrication of catalysts for CO2 reduction to targeting products with high efficiency. Herein, for the first time, a hybrid of BiOx encapsulated in carbon thin layer is developed as high active electrocatalyst for CO2 conversion, which is synthesized by pyrolysis using Bi MOF as precursor and sacrificial template. The carbon layer overcoating BiOx catalyst exhibits superior performance for CO2 reduction to formate, achieving a maximum Faradaic efficiency of 89.3 % and a maximum current density of 37.8 mA cm-2. It is found that the as-prepared BiOx catalyst is enriched with oxygen vacancies stabilized by the encapsulating carbon layer. Both the carbon layer and oxygen vacancies improve the charge transfer of the catalyst, in favor of the high formate current density. The defects of oxygen vacancies play a vital role in CO2 adsorption and activation and thereby further enhancing the electrocatalytic ability for formate production.
Abstract Nanoparticles can suppress asymmetric precursor support collapse during pyrolysis to create carbon molecular sieve (CMS) membranes. This advance allows elimination of standard sol‐gel support stabilization steps. Here we report a simple but surprisingly important thermal soaking step at 400 °C in the pyrolysis process to obtain high performance CMS membranes. The composite CMS membranes show CO 2 /CH 4 (50 : 50) mixed gas feed with an attractive CO 2 /CH 4 selectivity of 134.2 and CO 2 permeance of 71 GPU at 35 °C. Furthermore, a H 2 /CH 4 selectivity of 663 with H 2 permeance of 240 GPU was achieved for promising green energy resource‐H 2 separation processes.
A variety of materials are under investigation for use as anode materials in lithium-ion batteries, of which, the most promising are those containing silicon. 10 One such material is a composite formed via the dispersion of silicon in a resorcinol-formaldehyde (RF) gel followed by pyrolysis. Two silicon-carbon composite materials, carbon microspheres and nanofoams produced from nano-phase silicon impregnated RF gel precursors have been synthesized and investigated. Carbon microspheres are produced by forming the silicon-containing RF gel into microspheres whereas carbon nano-foams are produced by impregnating carbon fiber paper with the silicon containing RF gel to create a free standing electrode. 1-4,9 Both materials have demonstrated their ability to function as anodes and utilize the silicon present in the material. Stable reversible capacities above 400 mAh/g for the bulk material and above 1000 mAh/g of Si have been observed.
A variety of materials are under investigation for use as anode materials in lithium-ion batteries, of which, the most promising are those containing silicon. One such material is a composite formed via the dispersion of silicon in a resorcinol-formaldehyde (RF) gel followed by pyrolysis. Two silicon-carbon composite materials, carbon microspheres and nanofoams produced from nano-phase silicon impregnated RF gel precursors have been synthesized and investigated. Carbon microspheres are produced by forming the silicon-containing RF gel into microspheres whereas carbon nanofoams are produced by impregnating carbon fiber paper with the silicon containing RF gel to create a free standing electrode. Both materials have demonstrated their ability to function as anodes and utilize the silicon present in the material. Stable reversible capacities above 400 mAh/g for the bulk material and above 1000 mAh/g of Si have been observed.
A variety of materials are under investigation for use as anode materials in lithium-ion batteries, of which, the most promising are those containing silicon. 6 One such material is a composite formed via the dispersion of silicon in a resorcinol-formaldehyde (RF) gel followed by pyrolysis. Two silicon-carbon composite materials, carbon microspheres and nanofoams produced from nano-phase silicon impregnated RF gel precursors have been synthesized and investigated. Carbon microspheres are produced by forming the silicon-containing RF gel into microspheres whereas carbon nano-foams are produced by impregnating carbon fiber paper with the silicon containing RF gel to create a free standing electrode. 1-5 Both materials have demonstrated their ability to function as anodes and utilize the silicon present in the material. Stable reversible capacities above 400 mAh/g for the bulk material and above 1000 mAh/g of Si have been observed.
The present understanding of the origin of life based on Oparin's (1924) conception of life as a manifestation of matter in a special stage of its development is outlined. The results of chemical analyses of lunar samples are discussed, and their implications regarding chemical reactions beginning with carbonaceous dust are considered. Amino acids isolated from lunar samples taken from different sites show a high degree of similarity, in agreement with the hypothesis that carbon compounds, including amino acid precursors, were implanted on the lunar surface by components of the solar wind. The amino acid precursors are most likely a cyanide compound. Overlapping amino acid/carbon ratios from lunar samples and samples of meteorites suggest a common cosmochemical state of carbon in the solar system.
Despite the potential to lowering fabrication costs of pitch-based carbon fiber (CF) compared to polyacrylonitrile-based CF, large scale utilization is currently limited by the complexity in manufacturing. This is mainly due to the lack of consistency between the pitch structure/chemistry and CF properties under different processing conditions. Here, we employed full atomistic simulations based on reactive force fields to investigate the conversion of pitch precursors to CFs. Additionally, it was found that at the carbonization stage, the consumption rates of precursors, gas formations, and solid yields (carbonized CFs) are all dependent on the composition and arrangement of molecular moieties in the precursor. Specifically, precursors with sp 3 carbons in the cata-condensed core area have limited decomposition pathways (i.e., limited reaction sites), which leads to the formation of carbonized CFs with similar compositions. Furthermore, carbonized CFs possess distinct structural characteristics, and finally lead to the formation of CFs with different moduli. By analyzing CF crystallinity and elemental composition, general rationales are proposed for the selection of optimal precursors and processing conditions, and thus shed lights on parameter screening during industrial CF synthesis. For instance, inclusion of sp 3 carbons in cata- condensed rings can be preferred over the presence of sp 3 carbons on side chains.
Abstract Porous carbons are the active materials of choice for supercapacitor applications because of their power capability, long-term cycle stability, and wide operating temperatures. However, the development of carbon active materials with improved physicochemical and electrochemical properties is generally carried out via time-consuming and cost-ineffective experimental processes. In this regard, machine-learning technology provides a data-driven approach to examine previously reported research works to find the critical features for developing ideal carbon materials for supercapacitors. Here, we report the design of a machine-learning-derived activation strategy that uses sodium amide and cross-linked polymer precursors to synthesize highly porous carbons (i.e., with specific surface areas > 4000 m 2 /g). Tuning the pore size and oxygen content of the carbonaceous materials, we report a highly porous carbon-base electrode with 0.7 mg/cm 2 of electrode mass loading that exhibits a high specific capacitance of 610 F/g in 1 M H 2 SO 4 . This result approaches the specific capacitance of a porous carbon electrode predicted by the machine learning approach. We also investigate the charge storage mechanism and electrolyte transport properties via step potential electrochemical spectroscopy and quasielastic neutron scattering measurements.
Carbon fiber provides opportunity to reduce weight in structural composites, including wind turbine blades, due to the material's superior specific stiffness and specific strength compared to alternatives. Despite these advantages, cost and compressive performance are considered weaknesses for carbon fiber products available today. Studies to produce low-cost carbon fiber alternatives, including the use of textile-derived precursor systems, have shown progress and merit through the DOE/ORNL low-cost carbon fiber initiatives. Here, this work focuses on enabling increases in compressive strength through design of the carbon fiber geometry, applicable to both textile and conventional precursor systems, while also providing opportunities to reduce carbon fiber processing costs. Fiber-resin interface and fiber alignment are among the most frequently cited factors controlling composite compressive performance. However, it is believed that there is opportunity in traditionally unexplored routes to increasing compressive strength through alteration of the carbon fiber geometry by increasing the fiber area moment of inertia and/or the fiber perimeter and interfacial area. This paper presents initial results from manufacturing carbon fiber materials to assess the impacts of carbon fiber size on tested composite compressive performance with projected neutral or even beneficial impact on fiber and composite manufacturing economics. Carbon fiber systems with increasing size illustrate a favorable correlation for compressive performance greater than predicted from a micromechanical failure model. The manufacturing and mechanical test results support the hypothesis of this work that alterations to fiber geometry can be used to produce improvements of the compressive strength of carbon fiber reinforced polymers and provide incentive for related work in designing alternative shapes to further enhance compressive performance.
High-pressure carbon monoxide (HiPco) reactor, developed at Rice University, is used to produce single-walled carbon nanotubes (SWNT) from gas-phase reactions of iron carbonyl and nickel carbonyl in carbon monoxide at high pressures (10 - 100 atm). Computational modeling is used to better understand the HiPco process. In the present model, decomposition of the precursor, metal cluster formation and growth, and carbon nanotube growth are addressed. Decomposition of precursor molecules is necessary to initiate metal cluster formation. The metal clusters serve as catalysts for carbon nanotube growth. Diameter of metal clusters and number of atoms in these clusters are some of the essential information for predicting carbon nanotube formation and growth, which is then modeled by Boudouard reaction (2CO ---> C(s) + CO2) with metal catalysts. The growth kinetic model is integrated with a two-dimensional axisymmetric reactor flow model to predict reactor performance.
To limit the global warming to 1.5 °C above pre-industrial levels, beyond which the most dangerous impacts of climate change will occur, achieving carbon neutrality by the mid-21st century is essential. As the largest developing country and a significant contributor to carbon dioxide (CO 2 ) emissions, China has announced its ambitious climate commitment to pass carbon peak before 2030 and to achieve carbon neutrality by 2060. Both climate policies and regional clean air actions have been implemented for reductions in fossil fuel emissions, including the emissions of short-lived aerosols and precursors. Furthermore, in the context of pursuing carbon neutrality in China, aerosol reductions due to clean air actions and pollution control policies are very likely to have a great impact on climate. In this study, climate effects of aerosol reductions due to China's clean air actions under localized future emission scenarios are investigated using the Community Earth System Model version 1 (CESM1). Fully coupled and atmosphere-only experiments in years of carbon peak (2030) and carbon neutrality (2060) are performed with anthropogenic emissions of aerosols and precursors under “Current-goals” (Current) and “Carbon-Neutral” (Neutral) scenarios from the Dynamic Projection for Emissions in China (DPEC) model that consider socioeconomic development, climate policy, and pollution control actions (Figs. S1–S4 online). In addition, a present-day emissions simulation (PD) is conducted as the reference case (Supplementary materials online). Another sensitivity simulation is also conducted, with black carbon (BC) emissions set to follow the Neutral experiment but other emissions kept at the present-day levels (Neutral_BC), to quantify the relative roles of reducing strongly absorbing BC and other aerosols on future climate towards carbon neutrality. Greenhouse gases concentrations are kept at the 2015 levels in all simulations (Text S1 online).
Over the past decade, the production of biofuels from lignocellulosic biomass has steadily increased to offset the use of fuels from petroleum. To make biofuels cost-competitive, however, it is necessary to add value to the “ligno-” components (up to 30% by mass) of the biomass. The properties of lignin, in terms of molecular weight (MW), chemical functionality, and mineral impurities often vary from biomass source and biorefinery process, resulting in a challenging precursor for product development. Activated carbon (AC) is a feasible target for the lignin-rich byproduct streams because it can be made from nearly any biomass, and it has a market capacity large enough to use much of the lignin generated from the biorefineries. However, it is not known how the variability in the lignin affects the key properties of AC, because, until now, they could not be well controlled. In this work, various fractions of ultraclean (<0.6% ash) lignin are created with refined MW distributions using Aqueous Lignin Purification using Hot Agents (ALPHA) and used as precursors for AC. AC is synthesized via zinc chloride activation and characterized for pore structure and adsorption capacity. We show that AC surface area and the adsorption capacity increase when using lignin with increasing MW, and, furthermore, that reducing the mineral content of lignin can significantly enhance the AC properties. The surface area of the AC from the highest MW lignin can reach ~1830 m2/g (absorption capacity). Furthermore, single step activation carbonization using zinc chloride allows for minimal carbon burn off (<30%), capturing most of the lignin carbon compared to traditional burn off methods in biorefineries for heat generation.
A hydrogen peroxide initiated sol-gel process involving molybdenum transformation in the presence of dopamine (Dopa) hydrochloride excess produced the metastable precipitate composed of polydopamine (PDopa) spheres coated with Dopa preintercalated molybdenum oxide, (Dopa) x MoO y @PDopa. The hydrothermal treatment (HT) of the (Dopa) x MoO y @PDopa precursor resulted in the simultaneous carbonization of Dopa and molybdenum reduction generating MoO 2 nanoplatelets distributed and confined on the surface of the Dopa-derived carbon matrix (HT-MoO 2 /C). The consecutive annealing (An) of the HT-MoO 2 /C sample at 600 °C under Ar atmosphere led to the formation of MoO 2 with increased Mo oxidation state and improved structural stability (AnHT-MoO 2 /C). Annealing had also further facilitated interaction between the molybdenum-derived and Dopa-derived components resulting in the modification of the carbon matrix confirmed by Raman spectroscopy. Morphology of both materials is best described as Dopa-derived carbon spheres decorated with MoO 2 nanoplatelets. These integrated metal oxide and carbon structures were tested as electrodes for lithium-ion batteries in the potential window that corresponds to the intercalation mechanism of charge storage. The AnHT-MoO 2 /C electrode showed enhanced electrochemical activity, with an initial specific discharge capacity of 260 mAh/g and capacity retention of 67% after 50 cycles, compared to the HT-MoO 2 /C electrode which exhibited an initial specific discharge capacity of 235 mAh g –1 and capacity retention of 47% after 50 cycles. The rate capability experiments revealed that the capacity of 93 mAh/g and 120 mAh/g was delivered by the HT-MoO 2 /C and AnHT-MoO 2 /C electrodes, respectively, when the current density was increased to 100 mA/g. Here, the improved specific capacity, electrochemical stability, and rate capability achieved after annealing were attributed to higher crystallinity of MoO 2 , increased oxidation state of Mo, and formation of the tighter MoO 2 /carbon contact accompanied by the annealing assisted interaction between MoO 2 and Dopa-derived carbon.
Methane, the primary component of natural gas, is an energy-rich fuel by weight but exhibits lower energy density by volume than diesel and gasoline; efforts to increase its “volumetric” energy density have been focused on the design and synthesis of a porous scaffold that can bind the methane favorably. Novel approaches typically invoke the highly designable class of materials known as metal-organic frameworks (MOFs) owing to the relative difficulty of controlling carbon structure and composition precisely, without the use of a metal-based node. In this project, we instead explore the concept of carbon templating to achieve a porous scaffold with atomistically thin walls separated at a distance of ~1.2 nm, ideal for the formation of precisely two layers of methane per pore. This bottom-up templating approach permits the use of any small molecular precursor to build up the carbon scaffold, begging the question: which other elements (besides carbon) can be used to tune the surface for optimal methane binding without compromising the structure of the overall material? Boron and nitrogen were both explored and nitrogen was identified as the ideal agent for increasing methane binding to the optimal strength for use at near room temperature. Densification of the resulting materials by mechanical compaction was then explored to produce free-standing pellets with the highest methane “delivery” capacities of any known material. Here we define the amount “delivered” as the amount stored minus the amount remaining in the tank at 73 psi, the lowest useful pressure for vehicular transportation applications. The key features of the resulting methane storage system are rapid discharging and refueling speeds, extremely long cycle life (infinite cycle life for high-purity methane), a near-constant heat of refueling (making the heat generated upon refueling easier to manage), and a low maximum pressure of operation (<1500 psi), enabling the use of all-metal Type I cylinders and significantly reducing the costs of conversion of existing vehicles to cleaner burning, abundantly available natural gas). The technical effectiveness of this approach was further improved by exploring several cost-reduction strategies and investigating the reliability of such storage systems in the presence of “real” natural gas mixtures which contain a mixture of gaseous species.
This work uses a one-step KOH activation for lignin precursors to produce ultra-high mesoporous activated carbons (ACs) with an unprecedented combination of the surface area of 3207 m 2 g -1 and mesopore ratio of 76%. The ACs are applied for supercapacitors (SCs) and methylene blue (MB) adsorption. The capacitance of the SCs in the three-electrode system reaches 812.3 F g -1 and demonstrates a remarkable maximum MB adsorption capacity of 1250 mg g -1 . By modifying the process conditions, the mesopore ratio of ACs could be controlled from 10% to 80%. Compared with one-step activation, a two-step method produced microporous carbons with a lower surface area of 1227 m 2 g -1 and a high micropore ratio of 73%. The capacitance of SCs with two-step ACs reached 228.1 F g -1 and the maximum adsorption capacity of 476.19 mg g -1 for MB adsorption. The two-step method limited the surface area but had a higher oxygen surface functionality, benefiting its electrochemical performance. A techno-economic analysis reveals that the one-step KOH activation-based process develops ACs with a minimum selling price of $7648/ton. In conclusion, this work demonstrates tuning the processing-structure-property-performance relationship of lignin-based ACs to make an economically viable domestic carbon source.