Search NASA⌕ Search

SEARCH · Search NASA

Results for “delamination damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Low cost carbon fiber as potential lightning strike protection for wind turbine blades

Until recently, glass fiber composites (GFRP) were the preferred choice to prepare wind turbine blades due to their low cost compared to their counterpart carbon fiber composites (CFRP). However, to harvest the maximum wind energy, ever larger wind turbine blades are being manufactured. To support such a large structure carbon fiber composites CFRP have become the integral part of load bearing structures in the blade. In this work, we are proposing to utilize the low cost carbon fiber (LCCF), manufactured at Carbon Fiber Technology Facility (CFTF) of Oak Ridge National Laboratory (ORNL) as not only the cost effective alternative to the currently used carbon fiber (CF) but also as the lightning strike protection of the wind turbine blades. Wind turbines often get hit by lightning strikes due to their operating locations. LCCF can provide structural integrity to these gigantic structures and mitigate the effect of lightning strike on them by effectively dissipating the current. Two composite panels made of LCCF were tested against artificial lightning strikes of 100 kA and 200 kA (component A of lightning waveform SAE ARP 5412-B). The results showed very high resilience of LCCF composite due to their high electrical conductivity both in-plane and in through-thickness directions. There was no significant damage (fiber breakage, resin evaporation or delamination) in both the cases.

Kumar, Vipin↗
NASA NTRS1983

The effect of matrix properties and fiber properties on impact failure mechanics

The low-velocity impact problem in graphite/epoxy composite sheets must be solved before large amounts of that material can be used in commercial aircraft. Many of the low-velocity impacts that affect aircraft parts occur during normal ground operations and maintenance. Service equipment and tools have masses above 1 kg, and at velocities of less than 3 m/s can impact structural parts with energies higher than composites can endure without degradation of stiffness or strength. Simple solutions were developed for large-mass, low-velocity impacts which can be modeled as quasi-static events. Static test data and impact data show that the fiber properties control the impact energy which can be absorbed before penetration. Matrix shear strength and peel resistance control the extent of delamination. Comparison of results from tough matrix and brittle matrix composites show that although tough matrices reduce the extent of delamination, they lead to more fiber damage in the contact area.

Elber, W.↗
NASA NTRS1987

Composite structural materials

The development and application of composite materials to aerospace vehicle structures which began in the mid 1960's has now progressed to the point where what can be considered entire airframes are being designed and built using composites. Issues related to the fabrication of non-resin matrix composites and the micro, mezzo and macromechanics of thermoplastic and metal matrix composites are emphasized. Several research efforts are presented. They are entitled: (1) The effects of chemical vapor deposition and thermal treatments on the properties of pitch-based carbon fiber; (2) Inelastic deformation of metal matrix laminates; (3) Analysis of fatigue damage in fibrous MMC laminates; (4) Delamination fracture toughness in thermoplastic matrix composites; (5) Numerical investigation of the microhardness of composite fracture; and (6) General beam theory for composite structures.

Loewy, Robert G.↗
NASA NTRS2007

Millimeter Wave Holographical Inspection of Honeycomb Composites

Multi-layered composite structures manufactured with honeycomb, foam or balsa wood cores are finding increasing utility in a variety of aerospace, transportation, and infrastructure applications. Due to the low conductivity and inhomogeneity associated with these composites standard nondestructive testing (NDT) methods are not always capable of inspecting their interior for various defects caused during the manufacturing process or as a result of in-service loading. On the contrary, microwave and millimeter wave NDT methods are well-suited for inspecting these structures since signals at these frequencies readily penetrate through these structures and reflect from different interior boundaries revealing the presence of a wide range of defects such as disbond, delamination, moisture and oil intrusion, impact damage, etc. Millimeter wave frequency spectrum spans 30 GHz - 300 GHz with corresponding wavelengths of 10 - 1 mm. Due to the inherent short wavelengths at these frequencies, one can produce high spatial resolution images of these composites either using real-antenna focused or synthetic-aperture focused methods. In addition, incorporation of swept-frequency in the latter method (i.e., holography) results in high-resolution three-dimensional images. This paper presents the basic steps behind producing such images at millimeter wave frequencies and the results of two honeycomb composite panels are demonstrated at Q-band (33-50 GHz). In addition, these results are compared to previous results using X-ray computed tomography.

Case, J. T.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-32030-DND

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA?s Advanced Composites Project, a public-private partnership between government, universities and industry, seeks to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites is one of the three focused research areas of the project. One deliverable of the project is to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publically available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate polymer matrix composite (PMC) structures. The Handbook will reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. The Handbook will include an NDE Guidance Matrix that provides an applicability rating for NDE techniques as they apply to given flaw types. NDE techniques will include, but is not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types will include, but are not limited to porosity, delamination, voids, AFP defects and impact damage. The Handbook will contain details that support the applicability rating including, but not limited to, specimen details, inspection parameters, data analysis techniques, inspection efficiency (speed & cost), and limitations. This presentation will describe key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members.

Patricia A Howell↗
NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook – Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. NDE techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delamination, voids, AFP defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency (speed & cost), and limitations. This presentation will describe key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members to the NDE community is discussed.

Patricia A Howell↗
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
NASA NTRS1982

Lacquer Reveals Impact Damage in Composites

Brittle lacquer unveils effects normally visible only by ultrasonic inspection. Laquer coating measures spread of cracking and delamination in graphite/epoxy panels subjected to cyclic compression loads after impact damage. Test specimen is coated with lacquer on side opposite surface at which projectile will be fired. Spalled area shows effect of impact without removing specimen from test fixture.

Rhodes, M. D.↗
NASA NTRS1993

Damage tolerance of pressurized graphite/epoxy tape cylinders under uniaxial and biaxial loading

The damage tolerance behavior of internally pressurized, axially slit, graphite/epoxy tape cylinders was investigated. Specifically, the effects of axial stress, structural anisotropy, and subcritical damage were considered. In addition, the limitations of a methodology which uses coupon fracture data to predict cylinder failure were explored. This predictive methodology was previously shown to be valid for quasi-isotropic fabric and tape cylinders but invalid for structurally anisotropic (+/-45/90)(sub s) and (+/-45/0)(sub s) cylinders. The effects of axial stress and structural anisotropy were assessed by testing tape cylinders with (90/0/+/-45)(sub s), (+/-45/90)(sub s), and (+/-45/0)(sub s) layups in a uniaxial test apparatus, specially designed and built for this work, and comparing the results to previous tests conducted in biaxial loading. Structural anisotropy effects were also investigated by testing cylinders with the quasi-isotropic (0/+/-45/90)(sub s) layup which is a stacking sequence variation of the previously tested (90/0/+/-45)(sub s) layup with higher D(sub 16) and D(sub 26) terms but comparable D(sub 16) and D(sub 26) to D(sub 11) ratios. All cylinders tested and used for comparison are made from AS4/3501-6 graphite/epoxy tape and have a diameter of 305 mm. Cylinder slit lengths range from 12.7 to 50.8 mm. Failure pressures are lower for the uniaxially loaded cylinders in all cases. The smallest percent failure pressure decreases are observed for the (+/-45/90)(sub s) cylinders, while the greatest such decreases are observed for the (+/-45/0)(sub s) cylinders. The relative effects of the axial stress on the cylinder failure pressures do not correlate with the degree of structural coupling. The predictive methodology is not applicable for uniaxially loaded (+/-45/90)(sub s) and (+/-45/0)(sub s) cylinders, may be applicable for uniaxially loaded (90/0/+/-45)(sub s) cylinders, and is applicable for the biaxially loaded (90/0/+/-45)(sub s) and (0/+/-45/90)(sub s) cylinders. This indicates that the ratios of D(sub 16) and D(sub 26) to D(sub 11), as opposed to the absolute magnitudes of D(sub 16) and D(sub 26), may be important in the failure of these cylinders and in the applicability of the methodology. Discontinuities observed in the slit tip hoop strains for all the cylinders tested indicate that subcritical damage can play an important role in the failure of tape cylinders. This role varies with layup and loading condition and is likely coupled to the effects of structural anisotropy. Biaxial failure pressures may exceed the uniaxial values because the axial stress contributes to the formation of 0 deg ply splitting (accompanied by delamination) or similar stress-mitigating subcritical damage. The failure behavior of similar cylinders can also vary as a result of differences in the role of subcritical damage as observed for the case of a biaxially loaded (90/0/+/-45)(sub s) cylinder with a 12.7 mm slit. For this case, the methodology is valid when the initial coupon and cylinder fracture modes agree. However, the methodology underpredicts the failure pressure of the cylinder when a circumferential fracture path, suggestive of a 0 deg ply split, occurs at one slit tip. Thus, the failure behavior of some tape cylinders may be highly sensitive to the initial subcritical damage mechanism. Finite element analyses are recommended to determine how structural anisotropy and axial stress modify the slit tip stress states in cylinders from those found in flat plates since similarity of these stress states is a fundamental assumption of the current predictive methodology.

Priest, Stacy Marie↗
NASA NTRS1983

Fracture behavior of hybrid composite laminates

The tensile fracture behavior of 15 center-notched hybrid laminates was studied. Three basic laminate groups were tested: (1) a baseline group with graphite/epoxy plies, (2) a group with the same stacking sequence but where the zero-deg plies were one or two plies of S-glass or Kevlar, and (3) a group with graphite plies but where the zero-deg plies were sandwiched between layers of perforated Mylar. Specimens were loaded linearly with time; load, far field strain, and crack opening displacement (COD) were monitored. The loading was stopped periodically and the notched region was radiographed to reveal the extent and type of damage (failure progression). Results of the tests showed that the hybrid laminates had higher fracture toughnesses than comparable all-graphite laminates. The higher fracture toughness was due primarily to the larger damage region at the ends of the slit; delamination and splitting lowered the stress concentration in the primary load-carrying plies. A linear elastic fracture analysis, which ignored delamination and splitting, underestimated the fracture toughness. For almost all of the laminates, the tests showed that the fracture toughness increased with crack length. The size of the damage region at the ends of the slit and COD measurements also increased with crack length.

Kennedy, J. M.↗
NASA NTRS1985

Influence of interface ply orientation on fatigue damage of adhesively bonded composite joints

An experimental study of cracked-lap-shear specimens was conducted to determine the influence of adherend stacking sequence on debond initiation and damage growth in a composite-to-composite bonded joint. Specimens consisted of quasi-isotropic graphite/epoxy adherends bonded together with either FM-300 or EC 3445 adhesives. The stacking sequence of the adherends was varied such that 0 deg, 45 deg, or 90 deg plies were present at the adherend-adhesive interfaces. Fatigue damage initiated in the adhesive layer in those specimens with 0 deg nd 45 deg interface plies. Damage initiated in the form of ply cracking in the strap adherend for the specimens with 90 deg interface plies. The fatigue-damage growth was in the form of delamination within the composite adherends for specimens with the 90 deg and 45 deg plies next to the adhesive, while debonding in the adhesive resulted for the specimens with 0 deg plies next to the adhesive. Those joints with the 0 deg and 45 deg plies next to either adhesive has essentially the same fatigue-damage-initiation stress levels. These stress levels were 13 and 71 percent higher, respectively, than those for specimens with 90 deg plies next to the EC 3445 and FM-300 adhesives.

Johnson, W. S.↗
NASA NTRS1986

Influence of interface ply orientation on fatigue damage of adhesively bonded composite joints

An experimental study of cracked-lap-shear specimens was conducted to determine the influence of adherend stacking sequence on debond initiation and damage growth in a composite-to-composite bonded joint. Specimens consisted of quasi-isotropic graphite/epoxy adherends bonded together with either FM-300 or EC 3445 adhesives. The stacking sequence of the adherends was varied such that 0 deg, 45 deg, or 90 deg plies were present at the adherend-adhesive interfaces. Fatigue damage initiated in the adhesive layer in those specimens with 0 deg and 45 deg interface plies. Damaage initiated in the form of ply cracking in the strap adherend for the specimens with 90 deg interface plies. The fatigue-damage growth was in the form of delamination within the composite adherends for specimens with the 90 deg and 45 deg plies next to the adhesive, while debonding in the adhesive resulted for the specimens with 0 deg plies next to the adhesive. Those joints with the 0 deg and 45 deg plies next to either adhesive has essentially the same fatigue-damage-initiation stress levels. These stress levels were 13 and 71 percent higher, respectively, than those for specimens with 90 deg plies next to the EC 3445 and FM-300 adhesives.

Johnson, W. S.↗
NASA NTRS2009

Architectural Effects on Impact Resistance of Uncoated MI SiC/SiC Composites

Impact tests were conducted on uncoated 2D and 2.5D MI SiC/SiC composite specimens at room temperature and 1316 C in air. The specimens were analyzed before and after impact using optical microscopy, pulsed thermography (PT) and computed tomography (CT). Preliminary results indicate the following. Both 2-D and 2.5D composites show increase in surface and volumetric damages with increasing impact velocity. However, 2-D composites are prone to delamination cracks. In both 2D and 2.5D composites, the magnitude of impact damage at a fixed impact velocity is slightly greater at room temperature than at 1315 C. At a fixed projectile velocity and test temperature, the depth of penetration of the projectile into the substrate is significantly lower in 2.5D composites than in 2D composites. Fiber architecture plays a significant role controlling impact damage in MI SiC/SiC composites.

Bhatt, R. T.↗
NASA NTRS1994

Experimental verification of a progressive damage model for composite laminates based on continuum damage mechanics

Progressive failure is a crucial concern when using laminated composites in structural design. Therefore the ability to model damage and predict the life of laminated composites is vital. The purpose of this research was to experimentally verify the application of the continuum damage model, a progressive failure theory utilizing continuum damage mechanics, to a toughened material system. Damage due to tension-tension fatigue was documented for the IM7/5260 composite laminates. Crack density and delamination surface area were used to calculate matrix cracking and delamination internal state variables, respectively, to predict stiffness loss. A damage dependent finite element code qualitatively predicted trends in transverse matrix cracking, axial splits and local stress-strain distributions for notched quasi-isotropic laminates. The predictions were similar to the experimental data and it was concluded that the continuum damage model provided a good prediction of stiffness loss while qualitatively predicting damage growth in notched laminates.

Coats, Timothy William↗
DOE OSTI2021

An FEM-Based Peridynamic Model for Failure Analysis of Unidirectional Fiber-Reinforced Laminates

To predict the mixed damage modes of unidirectional fiber-reinforced polymer (FRP) laminates under dynamic loading, an FEM-based peridynamic model is introduced in this paper. Based on its geometric structure and material composition, a long fiber lamina is considered a transversely isotropic medium as a result of homogenization at the meso-scale. The laminated structure is modeled by stacking surface mesh layers with arbitrary fiber angles along the thickness direction. The peridynamic bonds between Gauss points connect the separated elements. These bonds are classified as inner-layer bonds and inter-layer bonds. To represent the anisotropy of a laminate, the micro-elastic modulus of the inner-layer and inter-layer bonds is calculated from the anisotropic engineering material constants separately. To capture complex failure behaviors of laminate structures, an empirical damage model is proposed for the tension/ compression breakage of peridynamic bonds. This damage model can control the in-plane and delamination failure process. Finally, benchmark tests are conducted to validate the elastic response of laminates under dynamic loading. In terms of damage analysis, the proposed model can capture the complex damage modes and resistive force of laminate structures.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Impact of Thermoplastic Composites: Testing and Modeling

Thermoplastic Composites (TPCs) are being increasingly considered for aerospace applications given their faster manufacturing cycles and lower cost. The NASA High-Rate Composite Aircraft Manufacturing (HiCAM) project aims to evaluate and mature thermoplastic manufacturing technologies to achieve a 4X – 6X increase in the production rate of Next Generation Single Aisle (NGSA) commercial aircraft. Within the purview of the NASA HiCAM project, this work investigates the response of thermoplastic composites under High Energy Dynamic Impact (HEDI) conditions. HEDI tests were conducted on panels fabricated with a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK) material system. A blunt metal projectile was chosen as the impactor which impacted the T700/LMPAEK panels over a range of impact velocities imparted by a gas gun test setup. As expected, lower velocity impacts caused the projectile to rebound, whereas higher velocity impacts resulted in the projectile penetrating the test panels. For the test cases in which the projectile rebounded, the predominant damage modes recorded with Ultrasonic (UT) scans included interlaminar delaminations which exhibited a “rotating fan” like structure when viewed in the through-thickness direction. Additionally, the dynamic deflection of the center point of the back face of the test panels and the velocity of the projectile was also measured during the test. Finite element models were developed to model a test case in which the projectile rebounded. These models were developed using LS-DYNA® wherein the primary objective was to evaluate the ability of the material model MAT299 to capture the dynamic response and damage modes in the T700/LMPAEK test panels. MAT299 is a Deformation Gradient Decomposition (DGD) based Continuum Damage Mechanics (CDM) material model. The interlaminar delaminations were modeled using the cohesive contact formulation available within LS-DYNA, wherein the mixed-mode fracture is captured via the Benzegaggh-Kenane (B-K) mode-dependent fracture energy interpolation law. The above-mentioned modeling methods have mostly been applied to thermoset composites and adapting them to TPCs involves addressing challenges associated with appropriately representing material behavior. Therefore, the proposed paper would discuss the systematic approach taken to adapt thermoset composites modeling practices for applications to TPCs, while appropriately addressing material behavior. The proposed paper would show that the predicted back face center point deflection correlated reasonably well with experimental data and the peak deflection was predicted to be within 5% of the experimental measurements. The projectile rebound velocity, while predicted to be higher than the experimental measurement, was within reasonable bounds. Additionally, it will be shown that the predicted delamination shapes were in reasonable agreement with experimental data.

Composite Materials↗
NASA NTRS2008

Characterization of Fatigue Damage for Bonded Composite Skin/Stringer Configurations

The fatigue damage was characterized in specimens which consisted of a tapered composite flange bonded onto a composite skin. Quasi-static tension tests were performed first to determine the failure load. Subsequently, tension fatigue tests were performed at 40%, 50%, 60% and 70% of the failure load to evaluate the debonding mechanisms. For four specimens, the cycling loading was stopped at intervals. Photographs of the polished specimen edges were taken under a light microscope to document the damage. At two diagonally opposite corners of the flange, a delamination appeared to initiate at the flange tip from a matrix crack in the top 45deg skin ply and propagated at the top 45deg/-45deg skin ply interface. At the other two diagonally opposite corners, a delamination running in the bondline initiated from a matrix crack in the adhesive pocket. In addition, two specimens were cut longitudinally into several sections. Micrographs revealed a more complex pattern inside the specimen where the two delamination patterns observed at the edges are present simultaneously across most of the width of the specimen. The observations suggest that a more sophisticated nondestructive evaluation technique is required to capture the complex damage pattern of matrix cracking and multi-level delaminations.

Paris, Isabelle↗