Search NASA⌕ Search

SEARCH · Search NASA

Results for “distributed propulsion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Upgrades to the Single Stage Axial Compressor and Fan Facility For Low Pressure Ratio and Boundary Layer Ingesting Fan Research

Next generation aircraft engine efficiency goals will be met through high bypass ratio engines. To achieve these goals, a combination of small core and low pressure ratio fan technologies will be necessary. Additionally, advanced propulsion air-frame integration concepts, such as boundary layer propulsion, and distributed electrically driven fans with short inlets or wing integration strategies, are beginning to be investigated for their potential fuel burn savings. In order to realize the potential fuel savings from these technologies, it is necessary to have testing capabilities for the components. The NASA Glenn Research Center (GRC) Single StageAxial Fan and Compressor Facility (also called the GRC W-8Facility) has recently undergone several significant upgrades in order to effectively test low pressure ratio fans and various inlet distortions. This paper will outline various challenges to testing low pressure ratio fans and the methods implemented to ensure that the W-8 facility is capable of performing these tests and acquiring high quality data. The upgrades include significant pip-ing upgrades to reduce pressure loss and turbulence, capability for inlet total pressure and swirl distortion, increased test section length including a longer shaft, a two component balance, an up-graded rotating data system, and a new temperature characterization to reduce uncertainties in thermocouple measurements

W-8 Facility↗
NASA NTRSDate not supplied

Integrated Handling Qualities Safety Analysis For Conceptual Design of Urban Air Mobility Vehicles

The recent emergence of distributed electric propulsion Vertical Takeoff and Landing (VTOL) aircraft has created a rapid introduction of new design concepts with unique stability and control characteristics. A challenge to realizing the full potential of these vehicles for urban transportation is to gain public acceptance which is largely driven by flight safety. This paper describes ongoing research to address the feasibility of integrating flying qualities safety metrics into conceptual design of VTOL Urban Air Mobility (UAM) vehicles. The discussion is composed of the approach and progress toward a toolbox that integrates with existing NASA rotorcraft design software and processes. Several key challenges are highlighted including modeling requirements for failures, identification of critical failures, and capturing critical failures, with robustness to model uncertainty. A discussion of requirements for safety metrics, specific to UAM vehicles, as well as the effects of the control system design is also included. Results to date have demonstrated the degradation in flying qualities metrics due to propulsion failures.

George Altamirano↗
NASA NTRSDate not supplied

Upgrades to the Single Stage Axial Compressor and Fan Facility For Low Pressure Ratio and Boundary Layer Ingesting Fan Research

Next generation aircraft engine efficiency goals will be met through high bypass ratio engines. To achieve these goals, a combination of small core and low pressure ratio fan technologies will be necessary. Additionally, advanced propulsion airframe integration concepts, such as boundary layer propulsion, and distributed electrically driven fans with short inlets or wing integration strategies, are beginning to be investigated for their potential fuel burn savings. In order to realize the potential fuel savings from these technologies, it is necessary to have testing capabilities for the components. The NASA Glenn Research Center (GRC) Single Stage Axial Fan and Compressor Facility (also called the GRC W-8 Facility) has recently undergone several significant upgrades in order to effectively test low pressure ratio fans and various inlet distortions. This paper will outline various challenges to testing low pressure ratio fans and the methods implemented to ensure that the W-8 facility is capable of performing these tests and acquiring high quality data. The upgrades include significant piping upgrades to reduce pressure loss and turbulence, capability for inlet total pressure and swirl distortion, increased test section length including a longer shaft, a two component balance, an upgraded rotating data system, and a new temperature characterization to reduce uncertainties in thermocouple measurements.

W-8 facitlity↗
NASA NTRS2023

X-57 Maxwell Airworthiness Validation Plan

This report is a Final Airworthiness Validation Plan (AVP) and describes how an aircraft like X-57 does (and does not) meet current airworthiness standards. The objective of this report is to create an example certification basis, associated means of compliance (MoC), and method of compliance for a distributed electric propulsion airplane under 14 Code of Federal Regulations (CFR) Part 21, “Certification Procedures for Products and Articles,” and its associated relevant sections of 14 CFR for “Airworthiness Standards” of Part 23, “Normal Category Airplanes,” Part 33 “Aircraft Engines,” and Part 35 “Propellers.” The approach to meet the objective is to use NASA’s X-57 Modification (Mod) IV flight demonstrator as an example and categorize its applicability to the regulations and standards according to the following three conditions: 1. Identify, where applicable, that the MoC and methods of compliance can be associated with existing Standard Specifications and Standard Practices of (ASTM) Committee F39 on Aircraft Systems and ASTM Committee F44 on General Aviation Aircraft; 2. If relevant ASTM standards do not exist, identify means and-or methods of compliance from appropriate Federal Aviation Administration (FAA) Advisory Circulars and other sources to use for the X-57 Mod IV vehicle; or 3. If no relevant certification rule, MoC, or method of compliance exists, highlight this omission and provide recommendations.

Herbert W Schlickenmaier↗
NASA NTRSDate not supplied

Application of Framework for Estimating Performance and Associated Uncertainty for Modified Aircraft Configurations Using NASA's X-57 Maxwell

A framework to estimate the performance and associated uncertainty of modified configurations of certified aircraft is applied to the X-57 Maxwell aircraft. In previous theoretical studies, the framework was shown to predict performance and uncertainty bounds accurately. The X-57 Maxwell is an experimental aircraft designed to demonstrate the benefits of distributed electric propulsion through a series of four incremental modifications to a Tecnam P2006T aircraft. The available models and data are first shown to be within the application domain of the framework. We then apply the framework to two X-57 Maxwell modifications. We compare the estimated performance and associated uncertainties against the airworthiness criteria. The results indicate that the framework is a promising tool for the certification by analysis workflow. We expect the framework to reduce and supplement the flight testing required to show compliance to airworthiness certification criteria for a modified configuration.

Uncertainty Quantification↗
NASA NTRSDate not supplied

Application of Framework for Estimating Performance and Associated Uncertainty for Modified Aircraft Configurations Using NASA's X-57 Maxwell

A framework to estimate the performance and associated uncertainty of modified configurations of certified aircraft is applied to the X-57 Maxwell aircraft. In previous theoretical studies, the framework was shown to predict performance and uncertainty bounds accurately. The X-57 Maxwell is an experimental aircraft designed to demonstrate the benefits of distributed electric propulsion through a series of four incremental modifications to a Tecnam P2006T aircraft. The available models and data are first shown to be within the application domain of the framework. We then apply the framework to two X-57 Maxwell modifications. We compare the estimated performance and associated uncertainties against the airworthiness criteria. The results indicate that the framework is a promising tool for the certification by analysis workflow. We expect the framework to reduce and supplement the flight testing required to show compliance to airworthiness certification criteria for a modified configuration.

Uncertainty Quantification↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the QUEEN V2 Test

A liquid-cooled electric ducted fan system was designed, built, and tested at the NASA Glenn Research Center. Main components of the system include a Commercial-Off- the-Shelf (COTS) fan and motor, and a custom-designed heat exchanger integrated into the fan duct. Fan speed, thrust, and cooling system thermal performance was measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V2.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for regional single-aisle aircraft. This test demonstrated the functionality of the QUEEN V2, quantified the thrust produced by the electrofan, and characterized the electrical and thermal performance of the system. Lessons learned will be used to guide development of future QUEEN prototypes.

Aerodynamics↗
NASA NTRSDate not supplied

Conceptual Design of the Hybrid-Electric Subsonic Single Aft Engine (SUSAN) Electrofan Transport Aircraft

This paper presents an update to the conceptual design of NASA’s Subsonic Single Aft Engine (SUSAN) Electrofan transport aircraft—a 180 passenger, Mach 0.785 hybrid-electric regional jet with an economy range of 750 nmi and a design range of 2,500 nmi. The concept employs a series hybrid-electric powertrain driven by a fuel-burning aft fuselage propulsor that is connected to Megawatt-class power generators to convert additional mechanical shaft power to electric power. This electric power is used to support wing-mounted electric propulsors. The aft fuselage turbofan leverages boundary layer ingestion (BLI) and is designed to deliver 35% of the total aircraft thrust, while the wing propulsors assume underwing distributed electric propulsion (DEP) arrangements and are responsible for the remaining 65% thrust. Investigated in this work is the fuel burn performance of the SUSAN Electrofan when incorporating new weight and efficiency estimates for the power, battery, and thermal systems. An updated unified engine deck is also included, which accounts for the high effective bypass ratio made possible by the DEP systems and turbofan BLI effects to first order. Multidisciplinary design analysis and optimization (MDAO) is performed through an updated conceptual design environment, and comparisons are made to a Boeing 737 MAX 8-like reference aircraft performing similar missions, as well as a variant resized for 2,500 nmi.

CAS↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the QUEEN V2 Test

A liquid-cooled electric ducted fan system was designed, built, and tested at the NASA Glenn Research Center. Main components of the system include a Commercial-Off- the-Shelf (COTS) fan and motor, and a custom-designed heat exchanger integrated into the fan duct. Fan speed, thrust, and cooling system thermal performance was measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V2.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for regional single-aisle aircraft. This test demonstrated the functionality of the QUEEN V2, quantified the thrust produced by the electrofan, and characterized the electrical and thermal performance of the system. Lessons learned will be used to guide development of future QUEEN prototypes.

Aeronautics-General↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the Acoustic Tests of the QUEEN V1

Noise produced by an electric ducted fan system was measured in tests at the NASA Glenn Research Center Acoustical Testing Laboratory. Main components of the system include a Commercial-Off- the-Shelf (COTS) fan and motor, an Electronic Speed Controller, a custom-designed inlet bellmouth, and several experimental inlet duct acoustic liners. Fan speed, thrust, and noise were measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V1.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for large regional single-aisle aircraft. Lessons learned will be used to guide development of future QUEEN prototypes. Results of a thermal test of the Electronic Speed Controller measured during this test are presented in a separate report.

L Danielle Koch↗
NASA NTRSDate not supplied

X-57 Systems Engineering Lessons Learned

The X-57 Maxwell is an electric aircraft based on a 4-passenger, twin engine Tecnam P2006T General Aviation aircraft. The X-57 project originally envisioned a straightforward integration of commercial-off-the-shelf hardware components and software into a novel configuration to demonstrate the aerodynamic and performance benefits of Distributed Electric Propulsion (DEP). The project was initially started with a high-risk venture capitalist approach under NASA’s Convergent Aeronautics Solutions (CAS) project, which led to an initial philosophy of Project Management “light” (which was then interpreted as Systems Engineering (SE) “light”). As the project matured, it was forced to transition to one with increasing SE-rigor as the project scope changed, hardware and software deficiencies were found, and the team realized the magnitude of the technical and integration challenges. In hindsight, these technical challenges came in part from an overly optimistic technology readiness assessment (TRA) at the beginning of the project, which resulted in the project assuming that little to no subsystem development would be required. The project’s approach to systems engineering evolved throughout three separate informal phases of the project as it underwent two key transitions as a result of the team wrestling with the technical challenges and resultant changing project scope. This paper discusses the assumptions, approaches, and challenges encountered from a Systems Engineering standpoint in each of the three informal phases of the X-57 project. This paper also provides recommendations on how future projects can apply Systems Engineering best practices upfront along with a realistic TRA to aid projects that find themselves with similar challenges.

Systems Engineering↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the Acoustic Tests of the QUEEN V1

Noise produced by an electric ducted fan system was measured in tests at the NASA Glenn Research Center Acoustical Testing Laboratory. Main components of the system include a Commercial-Off-the-Shelf fan, shroud, motor, and Electronic Speed Controller, plus a custom-designed inlet bellmouth, and four experimental inlet duct acoustic liners. Fan speed and noise were measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V1.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for large single-aisle aircraft. Results indicated that inlet duct acoustic liners reduced tone and broadband noise as compared to a hardwall inlet duct. Predicted performance of the honeycomb liner compared well with measurements from an array of far field microphones. Inlet acoustic liners are just one method for mitigating noise for electric ducted fans for aircraft propulsion systems. Lessons learned will be used to guide development of future QUEEN prototypes. Results of a thermal test of the Electronic Speed Controller are presented in a separate report.

Aircraft propulsion and power↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Thermal Analysis and Testing of the Electronic Speed Controller (ESC)

An electric ducted fan system was tested at the NASA Glenn Research Center. Main components of the system include a commercial-off-the-Shelf (COTS) fan and motor, electronic speed controller, and cooling system. Motor speed, voltage, current, and temperatures were measured in this static ground test of the propulsor. The thermal performance of the Electronic Speed Controller (ESC) was also measured using two different methods to cool the ESC: air cooling and cold plate cooling. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V1.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Single Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for large regional single-aisle aircraft. Lessons learned will be used to guide development of future QUEEN prototypes and thermal management systems.

Firas G Asfoor↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the Acoustic Tests of the QUEEN V1

Noise produced by an electric ducted fan system was measured in tests at the NASA Glenn Research Center Acoustical Testing Laboratory. Main components of the system include a Commercial-Off-the-Shelf fan, shroud, motor, and Electronic Speed Controller, plus a custom-designed inlet bellmouth, and four experimental inlet duct acoustic liners. Fan speed and noise were measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V1.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for large single-aisle aircraft. Results indicated that inlet duct acoustic liners reduced tone and broadband noise as compared to a hardwall inlet duct. Predicted performance of the honeycomb liner compared well with measurements from an array of far field microphones. Inlet acoustic liners are just one method for mitigating noise for electric ducted fans for aircraft propulsion systems. Lessons learned will be used to guide development of future QUEEN prototypes. Results of a thermal test of the Electronic Speed Controller are presented in a separate report.

Aircraft propulsion and power↗
NASA NTRS2004

Particulate Titanium Matrix Composites Tested--Show Promise for Space Propulsion Applications

Uniformly distributed particle-strengthened titanium matrix composites (TMCs) can be manufactured at lower cost than many types of continuous-fiber composites. The innovative manufacturing technology combines cold and hot isostatic pressing procedures to produce near-final-shape components. Material stiffness is increased up to 26-percent greater than that of components made with conventional titanium materials at no significant increase in the weight. The improved mechanical performance and low-cost manufacturing capability motivated an independent review to assess the improved properties of ceramic titanium carbide (TiC) particulate-reinforced titanium at elevated temperature. Researchers at the NASA Glenn Research Center creatively designed and executed deformation and durability tests to reveal operating regimes where these materials could lower the cost and weight of space propulsion systems. The program compares the elevated-temperature performance of titanium alloy Ti-6Al-4V matrix material to an alloy containing 10 wt% of TiC particles. Initial experiments showed that at these relatively low particle concentrations the material stiffness of the TMC was improved 20 percent over that of the plain Ti-6Al-4V alloy when tested at 427 C. The proportional limit and ultimate strength of the composite in tension are 21- and 14-percent greater than those of the plain alloy. Compression tests showed that the proportional limit is about 30 percent greater for TMC than for the plain alloy. The enhanced deformation resistance of the TMC was also evident in a series of tensile and compressive stress relaxation tests that were made. Specimens were subjected to tensile or compressive strain amplitudes of 0.75 percent for 24 hr followed by a return to zero strain imposed for 24 hr. The stress relaxation data were normalized with respect to the maximum stress for each case and plotted as a function of time in the following graph. Tensile stresses relaxed 19 percent for the TMC and 25 percent for the plain Ti-6Al-4V alloy. Compressive stresses relaxed 25 percent for the TMC and 39 percent for the plain Ti-6Al-4V alloy. The superior deformation resistance of the TMC extends to a creep rate that is 28-percent slower for the TMC when it is loaded to stress levels that are 26-percent higher than for the plain Ti-6Al-4V alloy.

Lerch, Bradley A.↗
NASA NTRS2014

Misconceptions of Electric Propulsion Aircraft and Their Emergent Aviation Markets

Over the past several years there have been aircraft conceptual design and system studies that have reached conflicting conclusions relating to the feasibility of full and hybrid electric aircraft. Some studies and propulsion discipline experts have claimed that battery technologies will need to improve by 10 to 20 times before electric aircraft can effectively compete with reciprocating or turbine engines. However, such studies have approached comparative assessments without understanding the compelling differences that electric propulsion offers, how these technologies will fundamentally alter the way propulsion integration is approached, or how these new technologies can not only compete but far exceed existing propulsion solutions in many ways at battery specific energy densities of only 400 watt hours per kilogram. Electric propulsion characteristics offer the opportunity to achieve 4 to 8 time improvements in energy costs with dramatically lower total operating costs, while dramatically improving efficiency, community noise, propulsion system reliability and safety through redundancy, as well as life cycle Green House Gas emissions. Integration of electric propulsion will involve far greater degrees of distribution than existing propulsion solutions due to their compact and scale-free nature to achieve multi-disciplinary coupling and synergistic integration with the aerodynamics, highlift system, acoustics, vehicle control, balance, and aeroelasticity. Appropriate metrics of comparison and differences in analysis/design tools are discussed while comparing electric propulsion to other disruptive technologies. For several initial applications, battery energy density is already sufficient for competitive products, and for many additional markets energy densities will likely be adequate within the next 7 years for vibrant introduction. Market evolution and early adopter markets are discussed, along with the investment areas that will fill technology gaps and create opportunities for the effective, near-term electric aircraft products. Without understanding both the context of how electric propulsion will integrate into the vehicle system, and evolve into the market place it is likely that electric propulsion will continue to be misunderstood.

Moore, Mark D.↗
NASA NTRS1976

The unified data system - A distributed processing network for control and data handling on a spacecraft

This paper presents the results obtained in a continuing investigation of real-time distributed processing systems which is being conducted at the Jet Propulsion Laboratory. A distributed processor architecture has been developed for control and data handling on a planetary spacecraft. This system, designated the Unified Data System, has been implemented in a feasibility breadboard. The following aspects of the Unified Data System are described: (1) standardized building block elements and their configuration into microprocessor modules, (2) a highly redundant bus structure which connects the various modules and facilitates intercommunications with minimal software support, (3) the structure of software within the individual modules and its coordination between modules, and (4) the mechanisms by which fault-tolerance can be implemented within the network. Through the attributes of multilevel standardization, simplicity, and flexibility, this system is expected to result in significant cost savings to future spacecraft missions.

Rennels, D. A.↗