Search NASA⌕ Search

SEARCH · Search NASA

Results for “external contamination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Study on the effect of contamination on the performance of X-ray telescopes

Modifications were made to the X-ray reflectometer located at the Space Sciences Laboratory, Marshall Space Flight Center. One was an automatic drive for the Large Micrometer Head. This system, interfaced with the Hewlett Packard Computer System, is used to record data and provides the X-ray reflectometer with an automated data-taking capability. Using this system, a complete scatter curve can be obtained automatically. Previously, it was necessary to manually reset the system after recording for each data point in the scatter curve. The second modification provided an externally controlled electrical drive to move the microfocus X-ray source along its axis. With this modification, one can translate the X-ray source while it is operating to locate the position providing maximum count rate.

Neal, W. R.↗
DOE OSTI2026

Elucidating the impact of stress states on grain boundary passivation in Ni-5Cr using the Rhines pack method

The oxidation behavior of a Ni–5Cr (at.%) alloy was evaluated at 420 ° C using the Rhines pack method and simultaneous tensile and compressive stress states via a miniature four-point bending fixture. At this moderate temperature, grain boundaries dominate mass transport and the resulting oxidation response. Oxidation produced approximately 1μ⁢m-wide protective Cr 2 O 3 films capping some grain boundaries and penetrative, intergranular Cr-rich oxides at other grain boundaries. Externally applied tensile and compressive stress during oxidation increased the prevalence of Cr 2 O 3 cap formation compared to no applied stress, with tensile stress resulting in more Cr 2 O 3 caps than compressive stress. The observed oxide cap morphology was similar across all test conditions. Regions under compressive stress showed an order of magnitude greater Cr depletion depth along the grain boundary. Chromium nitrides (CrN), likely from N contamination of the Rhines pack cell, were observed both at the oxide–metal interface and intergranularly within the alloy. Collectively these results demonstrate that applied stress promotes localized protective oxide cap formation over grain boundaries, with compressive stress additionally promoting deeper Cr depletion. Furthermore the experimental approach helped separate out the effects of stress on local oxide formation and grain boundary passivation.

4 point bend↗
NASA NTRS1999

Interaction of Space Suits with Windblown Soil: Preliminary Mars Wind Tunnel Results

Experiments in the Mars Wind Tunnel at NASA Ames Research Center show that under Mars conditions, spacesuit materials are highly susceptible to dust contamination when exposed to windblown soil. This effect was suspected from knowledge of the interaction of electrostatically adhesive dust with solid surfaces in general. However, it is important to evaluate the respective roles of materials, meteorological and radiation effects, and the character of the soil. The tunnel permits evaluation of dust contamination and sand abrasion of space suits by simulating both pressure and wind conditions on Mars. The long-term function of space suits on Mars will be primarily threatened by dust contamination. Lunar EVA activities caused heavy contamination of space suits, but the problem was never seriously manifest because of the brief utilization of the suits, and the suits were never reused. Electrostatically adhering dust grains have various detrimental effects: (1) penetration and subsequent wear of suit fabrics, (2) viewing obscuration through visors and scratching/pitting of visor surfaces, (3) penetration, wear, and subsequent seizing-up of mechanical suit joints, (4) changes in albedo and therefore of radiation properties of external heat-exchanger systems, (5) changes in electrical conductivity of suit surfaces which may affect tribocharging of suits and create spurious discharge effects detrimental to suit electronics/radio systems. Additional information is contained in the original.

Marshall, J.↗
DOE OSTI2020

Single differential $\nu_\mu$ charged-current cross section with the MicroBooNE detector using the Cosmic Ray Tagger

We perform a single differential $\nu_\mu$ charged current (CC) inclusive cross section measurement in MicroBooNE using improved detector response simulation, reconstruction, and with improved cosmic ray-induced background rejection using an external Cosmic Ray Tagger (CRT). The measurement uses data recorded from Fermilab’s Booster Neutrino Beamline (BNB) between December 2017 and July 2018, corresponding to an integrated protons on target of 7.6e18). We present the results in a similar manner as our previous $\nu_\mu$ charged current (CC) inclusive cross section to allow for direct comparison. The direct comparison highlights two improvements in this measurement over the previous measurement: firstly, the drastically reduced cosmic contamination achieved when using the CRT, and secondly the significantly improved detector modeling, with associated reduced systematic uncertainties. It is shown in this analysis that the outcome is an improved measurement (σ = 0.800 ± 0.030 (stat) ± 0.101 (sys) · 10 -38 cm 2 ) with much smaller uncertainties but a result consistent with that of the previous analysis (σ previous = 0.693 ± 0.010 ± 0.165 · 10 -38 cm 2 ).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS2007

Metabolic Heat Regenerated Temperature Swing Adsorption for CO2 and Heat Removal/Rejection in a Martian PLSS

Two of the fundamental problems facing the development of a Portable Life Support System (PLSS) for use on Mars, are (i) heat rejection (because traditional technologies use sublimation of water, which wastes a scarce resource and contaminates the premises), and (ii) rejection of carbon dioxide (CO2) in an environment with a CO2 partial pressure (ppCO2) of 0.4-0.9 kPa. Patent-pending Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed to address both these challenges. The technology utilizes an adsorbent that when cooled with liquid CO2 to near sublimation temperatures (~195K) removes metabolically-produced CO2 in the ventilation loop. Once fully loaded, the adsorbent is then warmed externally by the ventilation loop (~300K), rejecting the captured CO2 to Mars ambient. Two beds are used to provide a continuous cycle of CO2 removal/rejection as well as facilitate heat exchange out of the ventilation loop. Any cryogenic fluid can be used in the application; however, since CO2 is readily available on Mars and can be easily produced and stored on the Martian surface, the solution is rather elegant and less complicated when employing liquid CO2. As some metabolic heat will need to be rejected anyway, finding a practical use for metabolic heat is also an overall benefit to the PLSS. To investigate the feasibility of the technology, a series of experiments were conducted which lead to the selection and partial characterization of an appropriate adsorbent. The Molsiv Adsorbents 13X 8x12 (also known as NaX zeolite) successfully removed CO2 from a simulated ventilation loop at the prescribed temperature swing anticipated during PLSS operating conditions on Mars using a cryogenic fluid. Thermal conductivity of the adsorbent was also measured to eventually aid in a demonstrator design of the technology. These results provide no show stoppers to the development of MTSA technology and allow its development to focus on other design challenges as listed in the conclusions section of this paper.

Iacomini, Christine↗
NASA NTRSDate not supplied

Developing a Tool to Collect Microbiological Samples in Space

We developed and tested a tool to collect aseptic samples during extravehicular activity or space walks. This tool can withstand the extreme temperature (-92 – 90 ˚C) and pressure variations without compromising the sterility of the collection device or the integrity of the sample. Results from ground testing the tool demonstrate that external surfaces of space suits are not sterile and that a wide variety of human associated bacteria and some fungi can survive at least seven hours of exposure to vacuum. These bacteria include non-spore forming organisms like Staphylococcus that are not normally considered extremophiles We plan to use this tool to characterize the exterior of the International Space Station. We expect the results of this work to guide the planetary protection requirements and contamination control strategy for crewed missions to Mars. This tool could also be used to monitor contamination associated with the Artemis missions to the moon or collect aseptic samples robotically in environments that are not suitable for human exploration.

A B Regberg↗
NASA NTRS1981

LANDSAT 3 return beam vidicon response artifacts: A report on RBV photographic product characteristics and quality coding system

Analysis of large volumes of LANDSAT 3 RBV digital data that were converted to photographic form led to the firm identification of several visible artifacts (objects or structures not normally present, but producted by an external agency or action) in the imagery. These artifacts were identified, categorized, and traced directly to specific sensor response characteristics. None of these artifacts is easily removed and all cases remain under active study of possible future enhancement. The seven generic categories of sensor response artifacts identified to date include: (1) shading and stairsteps; (2) corners out of focus; (3) missing reseaus; (4) reseau distortion and data distortion; (5) black vertical line; (6) grain effect; and (7) faceplate contamination. An additional category under study, but not yet determined to be caused by sensor response, is a geometric anomaly. Examples of affected imagery are presented to assist in distinguishing between image content and innate defects caused by the sensor system.

Clark, B. P.↗
NASA NTRS2015

Extravehicular Activity and Planetary Protection

The first human mission to Mars will be the farthest distance that humans have traveled from Earth and the first human boots on Martian soil in the Exploration EVA Suit. The primary functions of the Exploration EVA Suit are to provide a habitable, anthropometric, pressurized environment for up to eight hours that allows crewmembers to perform autonomous and robotically assisted extravehicular exploration, science/research, construction, servicing, and repair operations on the exterior of the vehicle, in hazardous external conditions of the Mars local environment. The Exploration EVA Suit has the capability to structurally interface with exploration vehicles via next generation ingress/egress systems. Operational concepts and requirements are dependent on the mission profile, surface assets, and the Mars environment. This paper will discuss the effects and dependencies of the EVA system design with the local Mars environment and Planetary Protection. Of the three study areas listed for the workshop, EVA identifies most strongly with technology and operations for contamination control.

Buffington, J. A.↗
NASA NTRS1984

APART/PADE analytical evaluation of the diffuse infrared background experiment for NASA's cosmic background explorer

The stray light performance of NASA's Diffuse Infrared Background Experiment (DIRBE) has been calculated using the APART/PADE code. That code has been upgraded to handle off-axis optical systems such as DIRBE. Under observing conditions, sunlight is attenuated by 21 to 29 orders-of-magnitude; uniform diffuse illumination, by 6 to 9 orders of magnitude. The sunlight is attenuated by multiple diffraction at an external sun shield and by a forebaffle at the entrance to the DIRBE. Stray light is nearly a linear function of the Bidirectional Reflectance Distribution Function (BRDF) of the primary mirror at all wavelengths - or it can be made to be so by reducing the size of the field defining stop from 0.866 to 0.7 degrees square. For uniform diffuse illumination, half of the stray radiation comes from within 5 degrees of the center of the field-of-view. Particulate contamination of the primary mirror is expected to be a problem and special polishing and cleaning procedures are recommended - before mirror overcoating and again before flight.

Evans, D. C.↗
NASA NTRS2012

Magnetic Testing, and Modeling, Simulation and Analysis for Space Applications

The Aerospace Corporation (Aerospace) and Lockheed Martin Space Systems (LMSS) participated with Jet Propulsion Laboratory (JPL) in the implementation of a magnetic cleanliness program of the NASA/JPL JUNO mission. The magnetic cleanliness program was applied from early flight system development up through system level environmental testing. The JUNO magnetic cleanliness program required setting-up a specialized magnetic test facility at Lockheed Martin Space Systems for testing the flight system and a testing program with facility for testing system parts and subsystems at JPL. The magnetic modeling, simulation and analysis capability was set up and performed by Aerospace to provide qualitative and quantitative magnetic assessments of the magnetic parts, components, and subsystems prior to or in lieu of magnetic tests. Because of the sensitive nature of the fields and particles scientific measurements being conducted by the JUNO space mission to Jupiter, the imposition of stringent magnetic control specifications required a magnetic control program to ensure that the spacecraft's science magnetometers and plasma wave search coil were not magnetically contaminated by flight system magnetic interferences. With Aerospace's magnetic modeling, simulation and analysis and JPL's system modeling and testing approach, and LMSS's test support, the project achieved a cost effective approach to achieving a magnetically clean spacecraft. This paper presents lessons learned from the JUNO magnetic testing approach and Aerospace's modeling, simulation and analysis activities used to solve problems such as remnant magnetization, performance of hard and soft magnetic materials within the targeted space system in applied external magnetic fields.

magnetics↗
NASA NTRS2021

Terra MODIS Sees Solar Eclipses: Analysis of Reflective Solar Band Response at Multiple Radiance Levels

The MODIS imaging spectroradiometer instruments on-board NASA's Terra and Aqua satellites have 20 reflective solar bands (RSB) covering a wavelength range from 400 to 2200 nm. Radiance is calculated from processing raw signals with background, temperature, and electronic contamination corrected. Measured gain is calibrated with a fully Sunlit solar diffuser (SD) at a stable radiance level, considering a slowly changing SD reflectance degradation. These measurements provide time-dependent gain adjustment factors, and the calibration assumes a linear response for each band and detector. Hence, an analysis of the dependence on different radiance levels is warranted. The MODIS design has no mechanism for varying radiance levels, except for an attenuator screen. However, it has been in static configuration for Terra since mid-2003. An external source of radiance attenuation can be utilized during solar eclipse events, while maintaining high stability and accuracy of solar calibration standards. Due to its long mission lifetime, Terra has seen several Sun-Moon near-conjunction events when it coincides with the orbit path where the SD is directly illuminated. As of August 2020, we have identified 7 viable partial solar eclipses in the Terra mission data. We will discuss several results of our study, including comparison of measured SD signal to predicted radiance reduction based on a solar disk radiance model; nominal and outlier behavior as a function of bands, detectors, and mirror-sides; and comparison with other data sets. Our main conclusion from this study is that there is no notable correlation of detector-dependent trend with radiance level for most RSB bands.

Terra↗
NASA NTRS1993

Silazine to silica

Thin film silica and/or methyl silicone were detected on most external surfaces of the retrieved LDEF. Both solar ultraviolet radiation and atomic oxygen can convert silicones to silica. Known sources of silicone in or on the LDEF appear inadequate to explain the ubiquitous presence of the silica and silicone films. Hexamethyldisilazane (HMDS) was used as the Challenger tile waterproofing compound for the Challenger/LDEF deployment mission. HMDS is both volatile and chemically reactive at STP. In addition, HMDS releases NH3 which depolymerizes silicone RTV's. Polyurethanes are also depolymerized. Experiments are reported that indicate much of the silicone and silica contamination of LDEF resulted directly or indirectly from HMDS.

Harvey, Gale A.↗
DOE OSTI2022

User’s Manual for RESRAD-BUILD Code V.4: Vol. 1 – Methodology and Models Used in RESRAD-BUILD Code

The RESRAD-BUILD computer code models radionuclide release and transport in indoor environments and performs pathway analyses to evaluate the potential radiological dose and risk incurred by an individual who works or lives in a building contaminated with radioactive material or housing radioactively contaminated furniture or equipment. The code provides four geometries to characterize a radiation source: point, line, area, and volume, in which radionuclides are homogeneously distributed. Radionuclides contained in a source are considered to be released to the indoor air due to various processes including erosion (mechanically or weathering), diffusion (for tritium and radon in a volume source), or emanation (radon in a point, line, or area source). The release can proceed through different time phases with different rates. In RESRAD-BUILD Version 4.0, a dynamic ventilation model is implemented to simulate the fate and transport of source material particles and radionuclides after their releases. This dynamic ventilation model considers (1) air exchange between rooms in the building and between the rooms and the outdoor environment, (2) deposition from air to floor, (3) resuspension from the floor to the air, and (4) periodical vacuuming that reduces the floor deposition. The fate and transport modeling provides estimates of radionuclide concentrations in the source, in the air, and on the floor at different times, which are then integrated over the exposure duration for the calculation of radiation doses and cancer risks. A single run of the RESRAD-BUILD code can model a building with up to 9 rooms, 10 sources, and 10 receptors. The potential radiation dose and cancer risk incurred by each receptor are calculated for seven exposure pathways: (1) external radiation directly from the sources (accounting for shielding), (2) external radiation from radioactive particles deposited on the floors, (3) external radiation from airborne radionuclides, (4) inhalation of airborne radionuclides, (5) inhalation of radon and radon progenies, (6) inadvertent ingestion of radioactive particles directly from the source, and (7) ingestion of radioactive particles deposited on the floors. Various exposure scenarios can be modeled with RESRAD-BUILD, including but are not limited to, office worker, renovation worker, decontamination worker, building visitor, and resident. Both deterministic and probabilistic analyses can be performed to obtain results in both text reports and graphic displays.

61 RADIATION PROTECTION AND DOSIMETRY↗
NASA NTRS1991

Optical nebulosity in X-ray-selected, early type galaxies

This paper presents the results of an H-alpha + N II forbidden line narrowband imaging survey of X-ray-selected E and S0 galaxies. A novel technique is described for objectively optimizing the removal of stellar continuum light while providing well-defined estimates of systematic errors. The procedure has the additional benefit of eliminating sky contamination, specifically in image regions occupied by galaxy light. Consideration of the measured spectral energy distributions is included in the flux calibration procedure, and emission-line luminosities (or upper limits), corrected for Galactic foreground extinction, are tabulated for metric apertures. No connection is found between the 'boxiness' or 'diskiness' of stellar isophotes and emission-line or far-infrared luminosity. It is suggested that optical nebulosity in early-type galaxies contains a significant multiparameter dependence on active Galactic nuclei behavior, accretion from the hot interstellar medium, and mass injection from external sources.

Shields, Joseph C.↗
DOE OSTI2025

Carbon nanotube coated metal mesh: Bridging nanoscale and macroscale

A novel hybrid structure has been developed by growing carbon nanotubes (CNTs) on a metal mesh that functions as a literally unlimitedly extendable backbone. This hybrid material structure provides a new approach of extending CNTs’ advantageous properties such as ultrahigh thermal and electrical conductivities, high sensitivity to gases, and distinctive wettability for different liquids with chemical inertness to macroscale—otherwise available only in nano- and microscales. In this feasibility work, CNTs were grown on a Type 316 stainless steel (SS) mesh by self-catalytical chemical vapor deposition (CVD) without the need of an externally added catalyst or catalyst support. For the radially aligned and entangled CNT forest on the SS mesh, the average CNT diameter is around 50 nm, while the length varies from 20 to 25 µm. High-resolution transmission electron microscopy analysis revealed the multiwall structure of the CNTs with >30 rolled-up graphitic sheets. Raman spectra of the CNTs showed a dominant G band, indicating a well-ordered graphitic nanostructure. Being highly hydrophobic with a water contact angle of ∼145° and oleophilic, the CNT-coated SS mesh could be used in fluid separation and organic contaminant removal from water. Moreover, CNTs are recognized for their exceptional thermal conductivity and the CNT-coated mesh offers a supportive structure with directly connected CNTs for efficient heat transfer. Proof of concept has been achieved for the CNT-coated mesh’s potentials as a liquid filter and an thermal interface material (TIM). Specifically, the CNT-coated mesh demonstrated the capability of capturing water from a water-organic mixture with a 100 % efficiency while allowing organic liquids to pass through the filter. Furthermore, when used as a TIM, the CNT-coated mesh reduced the interfacial thermal impedance by >30 %.

Carbon nanotubes (CNTS)↗
NASA NTRS2012

Contamination Control and Hardware Processing Solutions at Marshall Space Flight Center

The Contamination Control Team of Marshall Space Flight Center's Materials and Processes Laboratory supports many Programs/ Projects that design, manufacture, and test a wide range of hardware types that are sensitive to contamination and foreign object damage (FOD). Examples where contamination/FOD concerns arise include sensitive structural bondline failure, critical orifice blockage, seal leakage, and reactive fluid compatibility (liquid oxygen, hydrazine) as well as performance degradation of sensitive instruments or spacecraft surfaces such as optical elements and thermal control systems. During the design phase, determination of the sensitivity of a hardware system to different types or levels of contamination/FOD is essential. A contamination control and FOD control plan must then be developed and implemented through all phases of ground processing, and, sometimes, on-orbit use, recovery, and refurbishment. Implementation of proper controls prevents cost and schedule impacts due to hardware damage or rework and helps assure mission success. Current capabilities are being used to support recent and on-going activities for multiple Mission Directorates / Programs such as International Space Station (ISS), James Webb Space Telescope (JWST), Space Launch System (SLS) elements (tanks, engines, booster), etc. The team also advances Green Technology initiatives and addresses materials obsolescence issues for NASA and external customers, most notably in the area of solvent replacement (e.g. aqueous cleaners containing hexavalent chrome, ozone depleting chemicals (CFC s and HCFC's), suspect carcinogens). The team evaluates new surface cleanliness inspection and cleaning technologies (e.g. plasma cleaning), and maintains databases for processing support materials as well as outgassing and optical compatibility test results for spaceflight environments.

Burns, DeWitt H.↗
NASA NTRS2015

Perchlorate Reduction by Yeast for Mars Exploration

Martian soil contains high levels (0.6 percentage by mass) of calcium perchlorate (Ca(ClO4)2), which readily dissociates into calcium and the perchlorate ion (ClO4−) in water. Even in trace amounts, perchlorates are toxic to humans and have been implicated in thyroid dysfunction. Devising methods to lessen perchlorate contamination is crucial to minimizing the health risks associated with human exploration and colonization of Mars. We designed a perchlorate reduction pathway, which sequentially reduces perchlorate to chloride (Cl−) and oxygen (O2), for implementation in the yeast Saccharomyces cerevisiae. Using genes obtained from perchlorate reducing bacteria Azospira oryzae and Dechloromonas aromatica, we plan to assemble this pathway directly within S. cerevisiae through recombinational cloning. A perchlorate reduction pathway would enable S. cerevisiae to lower perchlorate levels and produce oxygen, which may be harvested or used directly by S. cerevisiae for aerobic growth and compound synthesis. Moreover, using perchlorate as an external electron acceptor could improve the efficiency of redox-imbalanced production pathways in yeast. Although several perchlorate reducing bacteria have been identified and utilized in water treatment systems on Earth, the widespread use of S. cerevisiae as a synthetic biology platform justifies the development of a perchlorate reducing strain for implementation on Mars.

Perchlorate↗
DOE OSTI2019

Development of eXternal Nuclear Reaction Analysis (XNRA) Detection Technique for Quantifying Light Isotope Concentrations

The National Nuclear Security Administration’s Tritium Sustainment Program is responsible for the design, development, demonstration, testing, analysis, and characterization of tritium-producing burnable absorber rods (TPBARs) and their components used to produce tritium for the nation’s strategic stockpile. The FY19 call for proposals included the specific basic science research topic, “Demonstration and evaluation of advanced characterization methods, particularly for quantifying the concentration of light isotopes ( 1 H, 3 H, 3 He, and 4 He, 6 Li and 7 Li) in metal or ceramic matrices”. Last year the same language appeared in the call for proposals, and a project IWO-389859 was awarded to the Ion Beam Lab (IBL) at Sandia-NM which was successful using Elastic Recoil Detection, but in the future could have resulted in tritium contamination that jeopardized other equally important NNSA projects. An alternative approach using deuterium nuclear reaction analysis was proposed and funded in FY2019 which was also successful and eliminated any possibility of contaminating the Ion Beam Laboratory with tritium, and will be described in this report.

61 RADIATION PROTECTION AND DOSIMETRY↗