Search NASA⌕ Search

SEARCH · Search NASA

Results for “Base Composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Carbon fiber/epoxy vitrimer composite patch cured with bio‐based curing agents for one‐step repair metallic sheet and its recyclability

Abstract Vitrimers have gained a great deal of attention from researchers, yet research on its application is still lacking. This study, a novel bio‐based vitrimer was developed from epoxy (EP) and bio‐based curing agents, that is, cashew nut shell liquid (CNSL) and citric acid (CA), and then reinforced by carbon fiber. The vitrimers with different ratios of acid to epoxy (R ratio) at 0.30–0.40 contained ester and ether linkages. All EP/CA/CNSL vitrimers showed the stress relaxation over 70–100°C due to transesterification. The vitrimers were applied as polymer matrices for the carbon fiber composites and then used as repair patches. By using the carbon fiber‐reinforced vitrimer with the R ratio of 0.30, patch repair on a damaged alloy sheet revealed that approximately 98% of the tensile strength of the damaged alloy sheet was recovered. The vitrimer can be dissolved from carbon fiber composite to recover carbon fiber. The recovered carbon fiber retained good tensile strength compared to the pristine composite. Based on this study, the EP/CA/CNSL vitrimers showed the comparable thermomechanical properties with the epoxy vitrimer cured by the petroleum‐based curing agent. The vitrimer composite patch could therefore be an alternative new repair method to extend the service life of damaged structures.

Lorwanishpaisarn, Narubeth↗
DOE OSTI2021

Temperature-dependent deformation behavior of a CuZr-based bulk metallic glass composite

In this study, the effect of cryogenic testing temperatures on the deformation behavior of a CuZr-based bulk metallic glass composite (BMGC) has been investigated using in situ high energy X-ray diffraction. The yield strength and work-hardenability of the studied BMGC show an increasing trend from 298 K to 153 K. A higher yield strength at a lower temperature can be attributed to the larger difference in the volume shrinkage between the crystalline phase and the amorphous matrix. The increasing martensitic transformation degree of the crystalline phase from 298 K to 153 K results in the enhanced work-hardenability. These results lead to a better understanding of the temperature dependence of phase-transformation induced plasticity in CuZr-based BMGCs. (C) 2020 Elsevier B.V. All rights reserved.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Discovery, Design, Synthesis and Testing of High Performance Structural Alloys (Final Technical Report)

The overarching goal of this project is to understand the phase stability and mechanical behavior of non-stoichiometric multi-principal element alloy (MPEA) materials. In order to identify suitable alloys, we plan to use a combinatorial thin film screening approach, in collaboration with scientists at Lawrence Berkeley National Laboratory who are performing computational work as well as complementary experimental work. Specific tasks within the scope of this project include the fabrication, using thin film deposition from six sputtering targets, of combinatorial samples with multi-dimensional gradients in composition and microstructure. These samples are studied to screen MPEA systems for promising candidate alloys with specific composition(s), based on characterization of composition, structure and mechanical behavior across the thin film. We want to produce single-phase MPEAs with chemical homogeneity in a given thin film region, simple grain structures, and no intermetallic phases present. Gradient films facilitate first-pass screening for desirable characteristics and inform the next stage of work that involves fabrication of bulk MPEA specimens for (tensile) mechanical testing and characterization. To make the bulk alloys, metal (elemental) pieces are melted to form MPEAs, followed by heat treatment to homogenize the composition and microstructure. A subset of alloys is also cast, using vacuum arc melting, to yield larger samples (diameter ~1 cm and length ~5-10 cm) and these allow us to assess viability of scale-up for the alloys in structural applications. Further processing plans include rolling and heat treatment to recrystallize selected bulk MPEAs and grow grains to different extents, in order to investigate size effects in the mechanical behavior of MPEAs. Microspecimen testing will be performed (primarily in tension) to assess the mechanical behavior over a range of temperatures. The deformation microstructure of mechanically tested alloys will be characterized using transmission electron microscopy (TEM) to provide a scientific basis for understanding the structure-property relationships in MPEA mechanical behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Enhancing the capacitive performance of microporous materials with protic ionic liquids

Classical density functional theory (cDFT) is used to investigate the electrosorption of protic ionic liquids in porous electrodes within the framework of a coarse-grained model. The purpose of this study is to clarify the capacitive behavior of protic ionic liquids in confined geometry. Previous studies have indicated that thermodynamic properties (e.g., capacitance, phase behavior and ionic conductivity) are influenced by the composition of the acid-base system and show asymmetry between acid dominant versus base dominant compositions. Here, we find that the electric double layer capacitance can be significantly improved by using protic ionic liquids compared to its aprotic counterpart through optimization of the mixture composition (i.e., the ratio of acid to base). We demonstrate the influence of pore size and applied voltage on the capacitance performance of protic ionic liquids and provide insight into microscopic understanding of ion and solvent distributions inside micropores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Particle interspacing effects on the mechanical behavior of a Fe–TiB 2 metal matrix composite using FFT-based mesoscopic field dislocation mechanics

This paper presents an application to metal matrix composites (MMCs) of an enhanced elasto-viscoplastic Fast Fourier Transform (EVP-FFT) formulation coupled with a phenomenological continuum Mesoscale Field Dislocation Mechanics (MFDM) theory. Contrary to conventional crystal plasticity, which only accounts for plastic flow and hardening induced by statistically stored dislocations (SSDs), MFDM-EVP-FFT also describes the evolution of polarized geometrically necessary dislocation (GND) density and its effect on both plastic flow and hardening. Numerical results for a Fe–TiB 2 MMC made of a ferrite matrix (α-Fe) and elastic ceramic particles (TiB 2 ) are presented. Full-field simulations are performed using synthetic periodic unit cells representative of the MMC, with single-crystalline and polycrystalline matrix, for different particle interspacing distances. A strong dependence of the predicted equivalent stress, cumulated plastic strain and GND density fields with particle interspacing distance is observed, in contrast with conventional crystal plasticity. Correlations between these mechanical fields and microstructural features, and their influence on local and global mechanical behavior are examined for the different MMC microstructures.

42 ENGINEERING↗
DOE OSTI2022

Cs 3 Bi 2 I 9 -hydroxyapatite composite waste forms for cesium and iodine immobilization

Perovskite-based ceramic composites were developed as potential waste form materials for immobilizing cesium (Cs) and iodine (I) with high waste loadings and chemical durability. The perovskite Cs 3 Bi 2 I 9 has high Cs (22 wt%) and I (58 wt%) content, and thus can be used as a potential host phase to immobilize these critical radionuclides. In this work, the perovskite Cs 3 Bi 2 I 9 phase was synthesized by a cost effective solution-based approach, and was embedded into a highly durable hydroxyapatite matrix by spark plasma sintering to form dense ceramic composite waste forms. The chemical durabilities of the monolithic Cs 3 Bi 2 I 9 and Cs 3 Bi 2 I 9 -hydroxyapatite composite pellets were investigated by static and semi-dynamic leaching tests, respectively. Cs and I are incongruently released from the matrix for both pure Cs 3 Bi 2 I 9 and composite structures. The normalized Cs release rate is faster than that of I, which can be explained by the difference in the strengths between Cs-I and Bi-I bonds as well as the formation of insoluble micrometer-sized BiOI precipitates. The activation energies of elemental releases based on dissolution and diffusion-controlled mechanisms are determined with significantly higher energy barriers for dissolution from the composite versus that of the monolithic Cs 3 Bi 2 I 9 . The ceramic-based composite waste forms exhibit excellent chemical durabilities and waste loadings, commensurate with the state-of-the-art glass-bonded perovskite composites for I and Cs immobilization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Chemical Recycling of Carbon Fiber-Reinforced Nylon Composites

Nylon-based fiber-reinforced composites are widely used in various sectors due to their strength, durability, and lightweight properties. Despite their widespread use, recycling these composites is difficult due to the inability to separate fibers and thermal instability of nylon at high temperatures. Consequently, most nylon composites are landfilled, leading to significant economic loss. Current fiber recovery methods (i.e., pyrolysis) are energetically inefficient and preclude recovery of the matrix. Dissolution methods, such as using hexafluoroisopropanol (HFIP), allow recovery of polymer and fiber but are economically taxing and require extensive safety infrastructure. Herein we report tailored glycolysis of nylon-6 composites, resulting in separated constituent fibers and nylon-6 oligomers. Deconstruction kinetics reveal nylon’s molecular weight reductions from 32,600 to 2000 g/mol, while SEM and tensile testing confirm recovered fiber integrity. In conclusion, this approach offers a pathway to reclaim high-value materials from nylon composites, providing a strategy for the chemical recycling of fiber-reinforced composites.

Zheng, Jackie [Univ. of Tennessee, Knoxville, TN (↗
DOE OSTI2020

Creation of discrete active site domains via mesoporous silica poly(styrene) composite materials for incompatible acid–base cascade reactions

This work highlights the design and synthesis of bifunctional mesoporous silicate – polymer composite dual acid–base supported cascade catalysts. Compartmentalization of the two incompatible active sites is sought by segregating acid sites on the silica surface, and base sites within polymer chains and/or polymer domains. The ability to isolate and segregate active sites via control of the mesoporous silica pore size and polymer molecular weight is probed with silica samples functionalized by a grafting-to process. Supplemental activator and reducing agent (SARA) atom transfer radical polymerization is used to synthesize random copolymers containing protected primary amines. Thiol–ene ‘click’ chemistry facilitates silica functionalization via a convergent approach, with the ene-functionalized polymer end group and silica-grafted thiols forming SBA/MCM-SH-poly(styrene-co-2-(4-vinylbenzyl)isoindoline-1,3-dione). Polymer deprotection and thiol oxidation produces primary amine/sulfonic acid containing composite catalysts. With the polymer supported Lewis base and silica grafted Brønsted acid, the two-step deacetalization – Knoevenagel condensation cascade is explored to assess the ability of these polymer/silica hybrids to segregate active sites, allowing both acid and base site accessibility. Six composite catalysts are synthesized and tested in individual and cascade reactions with kinetic results demonstrating that lower molecular weight SBA-15-P1 and MCM-41-P1 catalysts outperform (higher turnover frequencies and initial rates) their higher molecular weight analogues, as well as a polymer-free system containing molecular active sites dispersed on the silica surface. Higher molecular weight composite catalysts perform more poorly due to limited chain solubility, mass transfer limitations, and poor catalyst accessibility. In many cases, the polymer chains effectively thread into the mesopores, with higher molecular weight polymers leading to pore blockage and inhibited mass transfer.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Deformation Mechanism Transition in Additively Manufactured Compositionally Graded Fe-Base Alloys

Microstructure-dependent deformation and fracture behavior was investigated for an additively manufactured compositionally graded alloy (CGA) printed using the laser-directed energy deposition (L-DED) method to explore an alternative approach for dissimilar metal joints in nuclear energy systems. The electron backscatter diffraction (EBSD) maps from scanning electron microscopy (SEM) display a clear microstructural transition with decreasing austenite-forming elements (Ni and Mn), from an austenite (γ) dominant structure, to a complex composite structure containing ferrite (α), martensite (α') and retained austenite, and then to a fully ferritic structure. EBSD data were recorded in situ during tensile testing in SEM, and the evolution of the deformation mechanism and microstructure was characterized using Kikuchi diffraction pattern analysis. Complementary analysis for high-resolution features was also performed using scanning transmission electron microscopy (STEM). The Ni/Mn-rich austenite-dominant microstructures showed a complex deformation mechanism of two-step martensitic transformation (γ→ε→α'), whereas the minor austenite phase retained in the ferrite and/or martensite matrix showed a single transformation route (γ→α'). Ordinary dislocation glide and twinning via partial dislocation glide were observed in the austenite deformation. Meanwhile, the ferrite and martensite grains deformed mainly by ordinary dislocation slips and grain rotation. Furthermore, static tensile fracture was also highly dependent on local composition and phase constituents.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Compositing and Characterization of SE Quadrant Waste Exemplars

This report outlines the experimental investigation and characterization of transport properties in Hanford SE quadrant High-Level Waste (HLW). The goal of the study was to establish baseline behaviors of bulk composite rheology and settling characteristics to facilitate waste treatment process design for the Waste Treatment and Immobilization Plant (WTP) and avoid waste conditions and properties favorable to bubble cascade gas release events. The study focused on two major objectives: 1) identifying, obtaining, and preparing relevant Hanford tank waste samples for evaluation and 2) quantifying the “as-received” rheology and transport properties of the samples. Twenty-three centrifuged core segments originating from tanks AN-101, AN-106, and AW-105 were selected based on compositional relevance to SE quadrant PUREX cladding waste. These materials were composited into five waste composites enriched with target analytes: aluminum (Al), iron (Fe), phosphate (PO 4 ), uranium (U), and zirconium (Zr). Physical property and transport testing examined particle size distributions, bulk densities, settling behaviors, rheological properties, shear strengths, and just-suspended mixing speeds (NJS). Testing revealed two distinct composite classifications based on rheological characteristics: non-Newtonian composites (Fe and PO 4 ) and Newtonian composites (Al, U, and Zr). The Fe and PO 4 composites exhibited slow settling rates and reduced mobilization proclivity, attributable to strong particle-particle interactions and the formation of yield structures within non-Newtonian slurries. In contrast, the Al, U, and Zr composites displayed rapid settling and dense compaction behaviors, indicative of minimal structuring and interactions. Shear strengths for all composites were generally low relative to prior studies of SE quadrant waste, with only the U composite showing elevated strength approaching values reported in previous literature. Repeat shear strength measurements revealed contributions from dense granular material in the U composite and stronger cohesive properties in the Al composite. Settling data highlighted hindered settling behavior, with rates falling more than one order of magnitude below estimates based on Stokes’ law and rate decreasing as composite UDS content increased. NJS testing demonstrated different mobilization behaviors between cohesive and granular composites. The Fe composite required the highest mixing rate for resuspension, while the Al composite was the easiest to resuspend. Comparison of measured NJS against predictions made using the Zwietering correlation suggests non-Newtonian behavior alters resuspension mechanics, rendering non-Newtonian systems more stable against resuspension lift forces relative to their granular counterparts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Predictive Contaminant Transport Simulation with P2R Model for the Composite Analysis Limited Source Sensitivity Case.

The Plateau to River (P2R) is a groundwater flow and contaminant fate and transport (F&T) simulation model used to support remedial activities conducted by the Central Plateau Cleanup Company at the Hanford Site in Washington State. Figure 1 illustrates the P2R Model extents, discretization, and boundary conditions. The P2R Model is utilized in the Composite Analysis (CA) for the Hanford Site as the computational engine for computing F&T predictions as described in CP-60406, Hanford Site Composite Analysis Technical Approach Description: Groundwater. The model simulates contaminants of concern within the saturated zone of the uppermost aquifer beneath the Central Plateau and downgradient to the Columbia River. CP-57037, Model Package Report for the Plateau to River Model Version 8.3 documents the current version of the P2R Model including a description of the conceptual site model, model development and calibration, and limitations to the model application. Simulations conducted to support the dose calculations required by the CA are documented in ECF-HANFORD-19-0119, Predictive Flow Simulation with the P2R Model for the Composite Analysis Base Case and ECF-HANFORD-19-0120, Contaminant Transport Simulation with the P2R Model for the Composite Analysis Base Case.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Composition and Structure of the EGS Collab Test Bed 1 Based Upon Electrical Resistivity Tomography, Core Compositions, and Wireline Logging

The nature of core from the EGS Collab project was characterized with high resolution XRF analyses on selected core intervals and wireline geophysical logs. Electrical resistivity profiles from the wireline geophysical surveys are consistent with the electrical resistivity tomographic three-dimensional images, and the XRF profiles show elevated levels of sulfur in the vicinity of the interpreted conductivity anomalies. The compositional and wireline logging data are consistent with interpretations from the electrical resistivity tomography data. Based upon these observations the best candidate for the source of the high electrical conductivities is the presence of significant amounts of sulfides within the unit.

Roggenthen, William↗
DOE OSTI2024

Design and Evaluation of Environmental Barrier Coatings for Protection of Ceramic Matrix Composites in Hydrogen-Based Turbines

This presentation at the 2024 FECM Spring Project Review Meeting summarizes ongoing work at NETL aimed at enabling the use of ceramic matrix composite (CMC) materials in next-generation high-efficiency power generation turbines fueled by hydrogen, natural gas, or other fuels. The work broadly involves three aspects (1) phase-field damage modeling of CMCs and the environmental barrier coatings (EBCs) used to protect them (2) computational design of new and improved EBCs and (3) performance testing of EBCs using a novel gas turbine combustion simulation rig developed at NETL. An overview on current status and next steps for each aspect of the project are presented.

ceramic matrix composite (CMC)↗
DOE OSTI2026

Water Vapor Resistant SiC/SiC Composite for Hydrogen-Based Turbines (Final Scientific Technical Report)

New material innovations are needed for the extreme environments of next generation, hydrogen-fueled turbine engines. Ceramic matrix composites (CMCs) offer high-temperature capability but are susceptible to degradation in high-temperature water vapor. Pratt & Whitney’s (P&W) baseline silicon carbide (SiC)/SiC CMC was initially applied to design a component in a hydrogen-fueled engine, verifying the existence of a design space and extracting boundary conditions to inform testing parameters. Several material innovations, including two fibers, interface coatings (IFC), and self-healing matrices (SHM), were investigated to improve high-temperature performance in water vapor. A boron-doped pyrocarbon (B-PyC) IFC and a SHM matrix with layers of zirconium nitride (ZrN) or zirconium diboride (ZrB 2 ) were developed to fabricate minicomposites with either standard Hi-Nicalon™ Type S (HNS) fibers or new Tyranno® SA4 fibers (SA4). The B-PyC IFC is functional but lacks in providing improved durability. A matrix consisting of thick layers of SiC and thin layers of ZrB 2 shows promise as a SHM that can effectively seal matrix cracks in this extreme environment. Minicomposites with HNS fibers generally outperform those with SA4 fibers.

08 HYDROGEN↗
DOE OSTI2024

MaterialsMap: A CALPHAD-based tool to design composition pathways through feasibility map for desired dissimilar materials, demonstrated with resistance spot welding joining of Ag-Al-Cu

Assembly of dissimilar metals can be achieved by different methods, for example, casting, welding, and additive manufacturing (AM). However, undesired phases formed in liquid-phase assembling processes due to solute segregation during solidification diminish mechanical and other properties of the processed parts. In the present work, an open-source software named MaterialsMap, has been developed based on the CALculation of Phase Diagrams (CALPHAD) approach. The primary objective of MaterialsMap is to facilitate the design of an optimal composition pathway for assembling dissimilar alloys with liquid-phases based on the formation of desired and undesired phases along the pathway. In MaterialsMap, equilibrium thermodynamic calculations are used to predict equilibrium phases formed at slow cooling rate, while Scheil-Gulliver simulations are employed to predict non-equilibrium phases formed during rapid cooling. Additionally, by combining these two simulations, MaterialsMap offers a thorough guide for understanding phase formation in various manufacturing processes, assisting users in making informed decisions during material selection and production. As a demonstration of this approach, a compositional pathway was designed from pure Al to pure Cu through Ag using MaterialsMap. The design was experimentally verified using resistance spot welding (RSW).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Unraveling electrochemo-mechanical aspects of core–shell composite cathode for sulfide based all-solid-state batteries

All-solid-state lithium batteries (ASSLBs) are emerging as promising next-generation batteries for electric vehicles owing to their high energy densities and safety features. However, challenges such as inadequate material percolation and low cathode utilization often hinder their potential. This paper presents a core–shell approach to optimize the cathode active material (CAM) utilization. The resultant CAM composite showed high ionic conductivity, a highly dense microstructure with <10% porosity, and minimal stack pressure changes during electrochemical cycling. The maximum CAM utilization was achieved while effectively mitigating electrochemo-mechanical side reactions by applying a uniformly coated Li 6 PS 5 Cl solid electrolyte layer (≈500 nm) and a LiNbO 3 buffer layer (≈10 nm) onto LiNi 0.8 Mn 0.1 Co 0.1 O 2 particles (LPSCl@LNO@NMC). The engineered LPSCl@LNO@NMC composites, which incorporated a 5 wt% LPSCl coating on LNO@NMC powders, exhibited a dense microstructure that enhanced the mechanical stability at the cathode. Sulfide-based solid electrolyte (SSE)/SSE contact provided better ionic pathways within the composite and increased CAM utilization. Thus, an enhanced reversible capacity (197 mA h g -1 ) and exceptional high-rate cycling performance (86.3% capacity retention after 1000 cycles at 2C) were observed. These findings pave the way for the advancement and commercialization of high-performance ASSLBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Material Extrusion Additive Manufacturing of Wood and Lignocellulosic Filled Composites

Wood and lignocellulosic-based material components are explored in this review as functional additives and reinforcements in composites for extrusion-based additive manufacturing (AM) or 3D printing. The motivation for using these sustainable alternatives in 3D printing includes enhancing material properties of the resulting printed parts, while providing a green alternative to carbon or glass filled polymer matrices, all at reduced material costs. Previous review articles on this topic have focused only on introducing the use of natural fillers with material extrusion AM and discussion of their subsequent material properties. This review not only discusses the present state of materials extrusion AM using natural filler-based composites but will also fill in the knowledge gap regarding state-of-the-art applications of these materials. Emphasis will also be placed on addressing the challenges associated with 3D printing using these materials, including use with large-scale manufacturing, while providing insight to overcome these issues in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Advances in multi-dimensional cellulose-based fluorescent carbon dot composites

Recently, fluorescent materials composed of carbon dots (CDs) have attracted increasing attention in diverse fields, including the environment, food, biology, and medicine. Cellulose has emerged as a promising class of materials for carriers due to its low cost, fascinating biodegradability, and various morphologies, especially in available different dimensions. By taking advantage of the respective superiority of fluorescent materials and cellulose carriers, the performance of fluorescence composite materials can be optimized and their application may be extended. Here, in this review, the study emphasizes the synthesis and applications of cellulose-based fluorescent materials with different dimensions. Moreover, some effective strategies and potential challenges for further development of cellulose-based fluorescent materials are discussed. A deeper understanding will provide a guide for the materials with ideal fluorescent performances.

42 ENGINEERING↗