Search NASA⌕ Search

SEARCH · Search NASA

Results for “COPPER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Ionizing Radiation Sensing with Functionalized and Copper-Coated SWCNT/PMMA Thin Film Nanocomposites

This paper studies the ionizing radiation effects on functionalized single-walled carbon nanotube (SWCNT)/poly(methyl methacrylate) (PMMA) thin-film nanocomposites [SWNT/PMMA]. The functionalized thin-film devices are made of ferrocene-doped SWCNTs, SWCNTs functionalized with carboxylic acid (COOH), and SWCNTs coated/ modified with copper. The nanocomposite was synthesized by the solution blending method and the resulting nanocomposite was spin-cast on interdigitated electrodes (IDEs). A 160 kV X-ray source was used to irradiate the thin film and changes in the electrical resistance of the nanocomposites due to X-rays were measured using a semiconductor device analyzer. Carboxylic acid functionalized and copper-coated SWCNT/PMMA nanocomposite showed a reduced response to X-rays compared to unfunctionalized SWCNT/PMMA nanocomposite. Ferrocene-doped SWCNT showed a higher sensitivity to X-rays at lower dose rates. This is in contrast to a previous study that showed that similar nanocomposites using functionalized multi-walled CNTs (MWCNTs) had demonstrated an improved response to X-rays ionizing radiation compared to unfunctionalized MWCNTs for all dose rates. Electrical measurements were also performed using the Arduino Nano microcontroller. The result showed that a relatively economical, lightweight-designed prototype radiation sensor based on SWCNT/PMMA thin-film devices could be produced by interfacing the devices with a modest microcontroller. This work also shows that by encapsulating the SWCNT/PMMA thin-film device in a plastic container, the effect of ambient humidity can be reduced and the device can still be used to detect X-ray radiation. This study further shows that the sensitivity of SWCNT to X-rays was dependent on both the functionalization of the SWCNT and the dose rate.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Time-Resolved Radioluminescence of the Polynuclear Copper(I) Phosphor Cu4I6²–. Different Temporal responses to Photo, X-Ray, β-Ray and α-Particle Excitation

Described for the first time are the time-resolved radioluminescence (TRRL) properties of the highly luminescent copper(I) cluster Cu4I62– using X-ray, b-ray and a-particle excitation. The copper(I) phosphors are two crystalline salts of this anion, [Na2(18-crown-6)2(H2O)3][Cu4I6] (I) and [Li(benzo-15-crown-5)2(H2O)]2[Cu4I6] (II), that had been shown to display strong photoluminescence (PL) when excited with ultraviolet light. The integrated radioluminescence (RL) spectra observed when pulsed X-rays were used as the excitation source are virtually the same as the PL spectra under comparable conditions. These temporal RL spectra are invariant at all observation times indicating that the observed scintillation occurs from a common excited state (or set of excited states). When the TRRL is collected from excitation with a pulsed X-ray source, b-ray decay from 90Sr or a-decay from 244Cm, the longer components (>2 μs) of the TRRL displayed (in each case) lifetimes comparable to those of the strictly exponential PL decays recorded under pulsed laser UV excitation. However, at shorter observation times (< 500 ns), the RL decay deviated from the exponential model, indicating a markedly different temporal luminescence behavior when these materials were excited with pulsed high energy radiation. Furthermore, this effect was the most pronounced for the a-particle excitation. These results suggest that the absorption of a very high energy X-ray photon, b-ray or a-particle at a site within the crystalline solid leads to a high local density of electronic excited states and that coupling between these states provides an alternative channel for excited state decay. Given that the patterns observed

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Exploring the Performance and Reliability of Screen-Printable Fire-Through Copper Paste on PERC Solar Cells

For 40 TW of PV required to transition our planet to 100% renewables, the silver (Ag) should disappear from PV production. Advantages of copper (Cu) over silver (Ag) include 1) bulk Cu has a similar conductivity to Ag (1.7 mu O-cm for Cu, 1.6 mu O-cm for Ag) and 2) Cu is approximately 100 times cheaper than Ag, making it an excellent potential replacement. Problems associated with copper (Cu) contacts include 1) easy oxidation and 2) diffusion into the Si cell and recombination activity.

copper paste↗
DOE OSTI2021

Cysteine Mutants of the Major Facilitator Superfamily-Type Transporter CcoA Provide Insight into Copper Import

Copper (Cu) is a redox-active micronutrient that is both essential and toxic. Its cellular homeostasis is critical for supporting cuproprotein maturation while avoiding excessive oxidative stress. The Cu importer CcoA is the prototype of the widespread CalT subfamily of the MFS-type transporters. Hence, understanding its molecular mechanism of function is significant. Here, we show that CcoA undergoes a thiol:disulfide oxidoreduction cycle, which is important for its Cu import activity.

MFS-type transporters↗
DOE OSTI2021

2D Copper Tetrahydroxyquinone Conductive Metal–Organic Framework for Selective CO 2 Electrocatalysis at Low Overpotentials

Abstract Metal–organic frameworks (MOFs) are promising materials for electrocatalysis; however, lack of electrical conductivity in the majority of existing MOFs limits their effective utilization in the field. Herein, an excellent catalytic activity of a 2D copper (Cu)‐based conductive MOF, copper tetrahydroxyquinone (CuTHQ), is reported for aqueous CO 2 reduction reaction (CO 2 RR) at low overpotentials. It is revealed that CuTHQ nanoflakes (NFs) with an average lateral size of 140 nm exhibit a negligible overpotential of 16 mV for the activation of this reaction, a high current density of ≈173 mA cm −2 at −0.45 V versus RHE, an average Faradaic efficiency (F.E.) of ≈91% toward CO production, and a remarkable turnover frequency as high as ≈20.82 s −1 . In the low overpotential range, the obtained CO formation current density is more than 35 and 25 times higher compared to state‐of‐the‐art MOF and MOF‐derived catalysts, respectively. The operando Cu K‐edge X‐ray absorption near edge spectroscopy and density functional theory calculations reveal the existence of reduced Cu (Cu + ) during CO 2 RR which reversibly returns to Cu 2+ after the reaction. The outstanding CO 2 catalytic functionality of conductive MOFs (c‐MOFs) can open a way toward high‐energy‐density electrochemical systems.

Majidi, Leily↗
DOE OSTI2022

Copper Complexes with Diazoolefin Ligands and their Photochemical Conversion into Alkenylidene Complexes

Abstract Homometallic copper complexes with alkenylidene ligands are discussed as intermediates in catalysis but the isolation of such complexes has remained elusive. Herein, we report the structural characterization of copper complexes with bridging and terminal alkenylidene ligands. The compounds were obtained by irradiation of Cu I complexes with N‐heterocyclic diazoolefin ligands. The complex with a terminal alkenylidene ligand required isolation in a crystalline matrix, and its structural characterization was enabled by in crystallo photolysis at low temperature.

Kooij, Bastiaan↗
DOE OSTI2021

Time-Resolved Grazing Incidence X-Ray Absorption Spectroscopy for the In Situ Investigation of the Initial Stages of Sputter-Deposited Copper Thin Films

The sputter deposition and the growth of thin copper films on float glass substrates are in situ studied using grazing incidence, reflection mode X-ray absorption fine structure spectroscopy with subsecond time resolution. The experimental data are compared with model calculations, assuming the presence of crystalline, face-centered cubic metallic Cu nanostructures. From a detailed analysis of the measured spectra, the film thickness as well as the surface roughness is determined, leading to a detailed understanding of the films growth as a function of the sputter deposition time. In particular, different stages of film growth can clearly be distinguished from the fits of the experimental data. The results suggest the formation of isolated, approximately nm-sized copper clusters in the initial phase of the film deposition for the first few seconds, a coalescence phase with a nominal thickness of ≈1.5–2.8 nm, constant roughness of about 1.4 nm for the subsequent ≈5 s, and finally 3D growth of the Cu crystallites in the film for later stages of film growth. Further prospects of the methodology are given.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrochemically Dealloyed 3D Porous Copper Nanostructure as Anode Current Collector of Li-Metal Batteries

The commercialization of high-energy Li-metal batteries is impeded by Li dendrites formed during electrochemical cycling and the safety hazards it causes. Here, a novel porous copper current collector that can effectively mitigate the dendritic growth of Li is reported. This porous Cu foil is fabricated via a simple two-step electrochemical process, where Cu-Zn alloy is electrodeposited on commercial copper foil and then Zn is electrochemically dissolved to form a 3D porous structure of Cu. The 3D porous Cu layers on average have a thickness of ≈14 um and porosity of ≈72%. This current collector can effectively suppress Li dendrites in cells cycled with a high areal capacity of 10 mAh cm -2 and under a high current density of 10 mA cm -2 . This electrochemical fabrication method is facile and scalable for mass production. In conclusion, results of advanced in situ synchrotron X-ray diffraction reveal the phase evolution of the electrochemical deposition and dealloying processes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Modification of Jet Velocities in an Explosively Loaded Copper Target with a Conical Cavity

Here, in this work, the design and execution of an experiment with the goal of demonstrating control over the evolution of a copper jet is described. Simulations show that when using simple multi-material buffers placed between a copper target with a conical cavity and a cylinder of high-explosive, a variety of jetting behaviors occur based on material placement, including both jet velocity augmentation and mitigation. A parameter sweep was performed to determine optimal buffer designs in two configurations. Experiments using the optimal buffer designs verified the effectiveness of the buffers at altering jet velocities. Similar trends were shown between the experimental results and the modeling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Transition in helium bubble strengthening of copper from quasi-static to dynamic deformation

Damage from low-temperature irradiation and the subsequent degradation of materials performance pose significant challenges for the storage of radioactive materials and for peripheral components in some nuclear reactor designs. Fully understanding the mechanical behavior of such materials requires test data for strain rates in both the quasi-static (< 10/s) and dynamic (>> 10/s) regimes. While dynamic testing has generally been avoided in the past for neutron irradiated (contamination concerns) and ion irradiated (insufficient volume) materials, surface-sensitive Richtmyer-Meshkov instability (RMI) tests were used in the present work to overcome these limitations. Here, nanopillar compression, nanoindentation, and RMI testing data from a helium implanted surface layer (~10 µm thick) were compiled to explore the effects of helium bubbles on the materials strength of high-purity copper at strain rates of 0.001/s – 10 8 /s. While nano-mechanical testing revealed increases in yield strength and hardness with increasing helium dose from 1000 to 4000 appm He, RMI indicated no significant changes in strength as compared to unimplanted copper. Here, this discrepancy in behavior was rationalized through a combination of recent literature and follow-on molecular dynamics (MD) simulations, leading to the conclusion that the nanoscale helium bubbles acting as dispersed barriers to dislocation motion at quasi-static strain rates collapse under shock loading and cease to be effective barriers at high strain rates.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding how defects and dopant atoms in copper surface oxides affect reactivity

Copper and its oxides are key catalytic materials, on which reactions often occur at the metal/oxide interface. Here, in this work, we directly connect the induction period observed during methanol-driven reduction of thin-film copper oxides to their atomic-scale structural order. Using temperature-programmed desorption (TPD) methanol titrations combined with scanning tunneling microscopy, we show that highly ordered oxide phases – particularly the “29” structure with its low defect density – exhibit long induction periods and initially low reactivity. The induction period, defined as the number of methanol TPD cycles required to reach half of the maximum formaldehyde yield, scales with oxide order and oxygen coverage. Enhanced reactivity of well-ordered oxides emerges only after repeated methanol adsorption/desorption cycles generate oxygen vacancies and new Cu(111)/Cu x O interfacial sites. In contrast, disordered or sub-stoichiometric oxides, which contain more intrinsic defects and interfaces, are active from the first TPD cycle. We further examine how dilute Pt and Rh dopants influence oxide order and reactivity: 1% Pt increases defect density and catalytic activity, while 1% Rh promotes oxide ordering and longer induction periods. These findings demonstrate that dilute alloying provides a potential method for tuning the structure and reactivity of Cu(111)/Cu x O interfaces.

Cu(111)Methanol oxidation↗
DOE OSTI2024

A computational study of the effects of graphene additions on electrical properties of polycrystalline copper

The addition of graphene has recently shown promise as a route for the significant improvement of the bulk electrical properties of metallic materials. Here, we explore the effects these additions have on the net electrical conductivity of fabricated copper-graphene (Cu-Gr) nanocomposites as a function of grain structure and grain boundary properties. Synthetic 3D microstructures were generated to represent polycrystalline copper with different average grain diameters and twinned grain boundary fractions. Then, the Poisson equation of electrical transport was solved using a finite difference method in order to predict the net electrical conductivity of each microstructure. In this context, the potential effect of graphene on the conductivity of the composite was evaluated as a function of the number of affected grain boundaries. The results of these calculations indicate that 1.) as supported by literature, net electrical conductivity decreases with decreasing grain size, 2.) the presence of twinned grain boundaries results in smaller loss of conductivity than would otherwise be expected, and 3.) the presence of graphene on the grain boundaries can be expected to lead to improvements in net electrical conductivity. However, we also find that 4.) when the Cu grain structure becomes sufficiently refined, the addition of graphene could conceivably result in significant improvements in electrical conductivity over and above coarse-grained Cu. It is estimated from our calculations that, assuming microstructures with average grain sizes between 100 nm and 100 μm and graphene conductivity 1000 to 10,000 that of a typical Cu grain boundary, an improvement in electrical conductivity of approximately 17% over that of bulk Cu may be attainable. Therefore, by performing this study we suggest a possible route for the improvement of Cu electrical properties through the addition of graphene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Study the existing form of copper ( p-type oxide/segregation ) and its release mechanism from the passive film of Ti-7Cu alloy

For this work, the existing form of copper and its release mechanism from the passive film of Ti-7Cu alloy was studied by Quantitative analysis of depth profile and series of electrochemical tests. Results were interpreted within the Point Defect Model-II. Copper does not form any p-type (cuprous or cupric) oxide but preferentially oxidises at the metal/film interface and segregated as Cu interstitials ($Cu^+_i$) and become substituted as $Cu^{x'}_{Ti}$ in the oxygen-deficient TiO 2-x barrier layer having n-type semiconducting character. Eventually, the segregated species of Cu preferentially dissolute through the film as Cu ions into the solution at film/solution interface via the Esaki-tunnelling effect.

Siddiqui, Muhammad Ali↗
DOE OSTI2021

Identification of Auger mechanisms responsible for low energy electron emission from graphene on copper using Auger-gamma coincidence spectroscopy

We have applied positron annihilation induced Auger-gamma coincidence spectroscopy to identify important mechanisms responsible for the emission of low energy electrons following the sudden creation of holes in bilayer graphene on copper substrate. The novel surface spectroscopic method measures the energy of the Doppler shifted annihilation gamma photon in coincidence with the Auger electron emitted following the relaxation of the hole created by the annihilation of a surface electron with a surface trapped positron. By extracting and theoretically modelling the annihilation gamma spectra coincident with low energy electrons, we associate majority of the intensity in the low energy (7 eV–25 eV) region of the Auger spectrum to electron emission following Auger decays of 2s holes in adsorbed oxygen and deep valence holes in graphene. We provide additional support to this conclusion by showing that most of the Auger electrons with energy less than ~ 25 eV are coincident with gamma photons with small Doppler shift (511 keV–512 keV) indicating that the primary electron whose annihilation resulted in low energy Auger electron emission had small momentum parallel to the gamma emission direction. On the other hand, majority of the Auger electrons measured in coincidence with the photons having maximum Doppler shift (515 keV–521 keV) were emitted following the decay of core holes (C 1s and O 1s). Furthermore, by selecting annihilation gamma photons coincident only with the O KVV (from surface adsorbed oxygen), C KVV (graphene), and Cu MVV (copper substrate) Auger electrons, we have also experimentally derived the energy spectrum of Doppler shifted gamma photons resulting from the annihilation of positrons with 1s electrons of O, 1s electrons of C and 3p electrons of Cu respectively. Model Doppler broadened gamma spectra produced using ab-initio calculations agree well with the experimentally derived line shapes. This demonstrates the ability of Auger-gamma coincidence method to experimentally resolve the Doppler broadened annihilation gamma spectrum from surfaces into its veiled electronic level constituents which has, heretofore, relied solely on theoretical analysis. Our results also demonstrate that the line shape of the Doppler broadened annihilation gamma peak reflect the chemical composition of the topmost atomic layer and can thus be used to characterize both external and inaccessible surfaces of porous materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Capillary-Enhanced Two-Phase Micro-Cooler Using Copper-Inverse-Opal Wick with Silicon Microchannel Manifold for High-Heat-Flux Cooling Application

In this work, we demonstrate a two-phase capillary-fed boiling micro-cooler that consists of a ~ 25-..mu..m-thick copper inverse opal (CIO) porous wicking structure for high-heat-flux boiling and a silicon 3D-manifold for distributed liquid delivery and vapor extraction across a 0.5 cm x 0.5 cm heated area. At low inlet water mass flow rates of 1.5 to 1.9 g(min)-1, the micro-cooler displays nearly two-phase boiling with exit vapor quality ~ 1 and a high critical heat flux (CHF) of 253 to 320 W cm-2 with low superheat of ~ 10 degrees C resulting in a thermal resistance of boiling ~ 0.025 cm2 degrees C W-1 or heat transfer coefficient of 0.4 MW m-2 degrees C-1. For higher flow rates of 5, 10, and 15 g(min)-1, the micro-cooler exhibits a hybrid single-phase and two-phase cooling regime where the contribution of the sensible heat (single-phase) cooling is linearly added to that of the two-phase cooling. For the highest flow rate of 15 g(min)-1, the CHF is increased to ~ 500 W cm-2 resulting in an overall thermal resistance of ~ 0.18 cm2 degrees C W-1. However, the two-phase heat transfer effectiveness, which estimates the utilization level of the inlet mass flow rate for two-phase boiling, is reduced to ~ 0.11. To achieve the best cooling system performances, the micro-cooler must operate entirely within the two-phase boiling regime (exit vapor quality or two-phase heat transfer effectiveness ~ 1). Ideally, the "coolant" should be delivered near its saturation temperature (~ 100 degrees C for water), which provides significant advantages for the energy-efficient operation of data centers and power electronics. We present detailed analysis with Infrared and high speed camera images at various inlet flow rates and heat fluxes to understand complex heat transfer in the micro-cooler. Furthermore, a conjugate thermofluidic simulation model, which incorporates the physics of capillary-fed boiling in a porous copper layer, agrees well with the experimental data.

capillary-enhanced boiling↗
DOE OSTI2023

Crystal plasticity modeling for the strengthening effect of multilayered copper–graphene nanocomposites

The paper explores plastic deformation mechanisms in metal–graphene nanocomposites, illustrating their material strengthening effects through a crystal plasticity finite element (CPFE) model. This model is compared with published experimental results, which have previously shown that the two-dimensional shape of graphene effectively controls dislocation motion and significantly enhances the strength of metals. Simulated nanopillar compression tests, using a physics-based CP model that incorporates surface nucleation and single-arm source dislocation mechanisms, help us understand dislocation motions at submicron length scales. The crystal plasticity models are applied to nanolayered composites with copper grain layers and monolayer graphene, featuring repeat layer spacings of 200 nm, 125 nm, and 70 nm, respectively. This study quantifies the accumulation of dislocations at the graphene interfaces, contributing to the ultra-high strength of copper–graphene composites. Furthermore, a Hall–Petch-like correlation is established between yield strength and the number of embedded graphene layers.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Power and energy capacity tradeoffs in an all-aqueous copper thermally regenerative ammonia battery

Thermally regenerative ammonia batteries (TRABs) can provide energy storage and produce electrical power from low-grade waste heat instead of electricity. The use of all-aqueous copper-based electrolytes has recently produced higher power densities than those achieved using previous TRAB approaches based on reversible metal deposition and dissolution processes, but further gains are possible in power and energy density. We investigated the limitations of power and energy density and how they are impacted by the electrolyte composition and discharge currents. By increasing the ammonia concentration from 1 to 5 M, the power density of the battery increased from 11.2 to 28.5 mW cm –2 , but the energy density decreased from 0.56 to 0.31 Wh L –1 . Increasing discharge current densities from 4 to 12.5 mA cm –2 increased the average power density during discharge from 2.4 to 5.9 mW cm –2 without appreciable losses in energy density. Increasing the copper concentration from 0.1 to 0.5 M increased both energy density to 2.15 Wh L –1 and energy efficiency to 2.2% but did not substantially impact the power density. Furthermore, these results represent the highest performance metrics achieved for a low-grade waste heat to electricity system.

25 ENERGY STORAGE↗
DOE OSTI2025

In-situ synchrotron X-ray study on microstructure and stress evolutions of electroplated copper upon self-annealing

Background: The self-annealing behavior of electroplated copper (Cu) at room temperature is gaining attention in the microelectronics industry due to its significant impact on reliability issues such as substrate warpage and electrical resistivity. Methods: In this study, in-situ analysis of the microstructure transition and stress relaxation of the electroplated copper upon self-annealing was conducted via synchrotron white X-ray nanodiffraction (beamline 21A, Taiwan Photon Source) and grazing-incidence X-ray diffraction (beamline 17B1, Taiwan Light Source). Significant Findings: Remarkable relaxations of deviatoric stress and absolute strain component along the [002] direction were closely related to the Cu grain growth and crystallographic reorientation at the early stage of selfannealing, and a complete stress/strain relaxation can be achieved with the cessation of microstructure transition. In conclusion, the in-situ synchrotron X-ray studies provided an insight into Cu self-annealing mechanism, offering valuable information for improving Cu interconnect reliability.

Cu Self-annealing↗