SEARCH · Search NASA

Results for “Empirical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1992

An empirical model and an inversion technique for radar scattering from bare soil surfaces

Polarimetric radar measurements were conducted for bare soil surfaces under a variety of roughness and moisture conditions at L-, C-, and X-band frequencies at incidence angles ranging from 10 to 70 deg. Using a laser profiler and dielectric probes, a complete and accurate set of ground truth data were collected for each surface condition, from which accurate measurements were made of the rms height, correlation length, and dielectric constant. Based on knowledge of the scattering behavior in limiting cases and the experimental observations, an empirical model was developed which was found to yield very good agreement with the backscattering measurements of this study, as well as with measurements reported in other investigations. An inversion technique for predicting the rms height of the surface and its moisture content from multipolarized radar observations is developed on the basis of the model.

Oh, Yisok↗

NASA NTRS1992

Composition changes and empirical models

Empirical model descriptions of the response of the neutral thermosphere to magnetic activity have become increasingly sophisticated over the last two decades. The latest CIRA model (MSIS-86) includes a dependence of the thermospheric response to magnetic activity on altitude, latitude, local time, season, longitude, UT, and time history of magnetic activity. A primary assumption is that density changes are directly related to the measured magnetic activity and the goal is for the model to be representative of the typical or average response for any given level of magnetic activity under specified ancillary conditions. Unfortunately, available measurements for the larger storms are too sparse to give good averages and storm response may not be uniquely represented by current magnetic indices. Point by point comparisons with the MSIS-86 model have standard deviations of 20 percent for 0 and 30 percent for N2 and He at high latitudes during storm conditions.

Hedin, A. E.↗

NASA NTRS1951

Empirical relation between induced velocity, thrust, and rate of descent of a helicopter rotor as determined by wind-tunnel tests on four model rotors

The empirical relation between the induced velocity, thrust, and rate of vertical descent of a helicopter rotor was calculated from wind tunnel force tests on four model rotors by the application of blade-element theory to the measured values of the thrust, torque, blade angle, and equivalent free-stream rate of descent. The model tests covered the useful range of C(sub t)/sigma(sub e) (where C(sub t) is the thrust coefficient and sigma(sub e) is the effective solidity) and the range of vertical descent from hovering to descent velocities slightly greater than those for autorotation. The three bladed models, each of which had an effective solidity of 0.05 and NACA 0015 blade airfoil sections, were as follows: (1) constant-chord, untwisted blades of 3-ft radius; (2) untwisted blades of 3-ft radius having a 3/1 taper; (3) constant-chord blades of 3-ft radius having a linear twist of 12 degrees (washout) from axis of rotation to tip; and (4) constant-chord, untwisted blades of 2-ft radius. Because of the incorporation of a correction for blade dynamic twist and the use of a method of measuring the approximate equivalent free-stream velocity, it is believed that the data obtained from this program are more applicable to free-flight calculations than the data from previous model tests.

Castles, Walter, Jr.↗

NASA NTRS1993

Design of a cooperative problem-solving system for enroute flight planning: An empirical study of its use by airline dispatchers

In a previous report, an empirical study of 30 pilots using the Flight Planning Testbed was reported. An identical experiment using the Flight Planning Testbed (FPT), except that 27 airline dispatchers were studied, is described. Five general questions were addressed in this study: (1) under what circumstances do the introduction of computer-generated suggestions (flight plans) influence the planning behavior of dispatchers (either in a beneficial or adverse manner); (2) what is the nature of such influences (i.e., how are the person's cognitive processes changed); (3) how beneficial are the general design concepts underlying FPT (use of a graphical interface, embedding graphics in a spreadsheet, etc.); (4) how effective are the specific implementation decisions made in realizing these general design concepts; and (5) how effectively do dispatchers evaluate situations requiring replanning, and how effectively do they identify appropriate solutions to these situations.

Smith, Philip J.↗

NASA NTRS1993

A preliminary empirical evaluation of virtual reality as an instructional medium for visual-spatial tasks

We explored the training potential of Virtual Reality (VR) technology. Thirty-one adults were trained and tested on spatial skills in a VR. They learned a sequence of button and knob responses on a VR console and performed flawlessly on the same console. Half were trained with a rote strategy; the rest used a meaningful strategy. Response times were equivalent for both groups and decreased significantly over five test trials indicating that learning continued on VR tests. The same subjects practiced navigating through a VR building, which had three floors with four rooms on each floor. The dependent measure was the number of rooms traversed on routes that differed from training routes. Many subjects completed tests in the fewest rooms possible. All subjects learned configurational knowledge according to the criterion of taking paths that were significantly shorter than those predicted by a random walk as determined by a Monte Carlo analysis. The results were discussed as a departure point for empirically testing the training potential of VR technology.

Regian, J. Wesley↗

NASA NTRS1992

A semi-empirical model for the complete orientation dependence of the growth rate for vapor phase epitaxy - Chloride VPE of GaAs

A semi-empirical model has been developed to determine the complete crystallographic orientation dependence of the growth rate for vapor phase epitaxy (VPE). Previous researchers have been able to determine this dependence for a limited range of orientations; however, our model yields relative growth rate information for any orientation. This model for diamond and zincblende structure materials is based on experimental growth rate data, gas phase diffusion, and surface reactions. Data for GaAs chloride VPE is used to illustrate the model. The resulting growth rate polar diagrams are used in conjunction with Wulff constructions to simulate epitaxial layer shapes as grown on patterned substrates. In general, this model can be applied to a variety of materials and vapor phase epitaxy systems.

Seidel-Salinas, L. K.↗

NASA NTRS1992

Transition of oscillatory flow in tubes - An empirical model for application to Stirling engines

Attention is given to an empirical model for transition to turbulence in oscillatory flows in straight tubes. Designed after a correlation for transition of a boundary layer on a flat plate, the model yields the laminar flow momentum thickness Reynolds number that must be met before transition to turbulence will occur. The transition point is located by comparing this to the actual momentum thickness Reynolds number. A scheme is proposed for estimating the momentum thickness Reynolds number in terms of the position within the cycle, the maximum value of the diameter Reynolds within the cycle, Re(max), and the dimensionless frequency, Valensi number. Results from an experimental study of oscillatory flow in a tube are employed to develop the model. When the flow is determined to be turbulent, it is proposed that a fully-developed, steady flow friction coefficient be applied. When the flow is laminar, the assumption of fully developed flow cannot be made; thus, a method is suggested for estimating the friction factor.

Simon, T. W.↗

NASA NTRS1993

Semi-empirical model for prediction of unsteady forces on an airfoil with application to flutter

A semi-empirical model is described for predicting unsteady aerodynamic forces on arbitrary airfoils under mildly stalled and unstalled conditions. Aerodynamic forces are modeled using second order ordinary differential equations for lift and moment with airfoil motion as the input. This model is simultaneously integrated with structural dynamics equations to determine flutter characteristics for a two degrees-of-freedom system. Results for a number of cases are presented to demonstrate the suitability of this model to predict flutter. Comparison is made to the flutter characteristics determined by a Navier-Stokes solver and also the classical incompressible potential flow theory.

Mahajan, A. J.↗

NASA NTRS1937

Empirical corrections to the span load distribution at the tip

An analysis of existing pressure-distribution data was made to determine the variation of the tip loading with wing plan form. A series of empirical tip corrections was derived that may be added to theoretical curves in certain cases to obtain a closer approach to the actual loading at the tip. The analysis indicated that the need for a tip correction decreases as either the aspect ratio or the wing taper is increased. In general, it may be said that, for wings of conventional aspect ratio, corrections to the theoretical span load curves are necessary only if the wing is tapered less than 2:1 and has a blunt tip. If the tip is well rounded in plan form, no correction appears necessary even for a wing with no taper.

Pearson, H A↗

NASA NTRS1951

Empirical Relation Between Induced Velocity, Thrust, and Rate of Descent of a Helicopter Rotor as Determined by Wind-tunnel Tests on Four Model Rotors

Castles, Walter, Jr↗

NASA NTRS1948

Empirical mode constants for calculating frequencies of axial-flow compressor blades

The vibration characteristics of a group of axial-flow compressor blades of similar geometry were investigated. Empirical-mode constants were determined for the first three bending and torsional modes. A comparison of experimentally determined frequencies of a second group of blades with frequencies computed using these mode constants showed that the computed values were correct within 10 percent. The approximate limiting ratios of depth to chord and length to chord below which these constants could not be used to compute the natural frequencies were also found experimentally.

COMPRESSORS - STRESS AND VIBRATION↗

NASA NTRS1951

Comparison of measured efficiencies of nine turbine designs with efficiencies predicted by two empirical methods

Empirical methods of Ainley and Kochendorfer and Nettles were used to predict performances of nine turbine designs. Measured and predicted performances were compared. Appropriate values of blade-loss parameter were determined for the method of Kochendorfer and Nettles. The measured design-point efficiencies were lower than predicted by as much as 0.09 (Ainley and 0.07 (Kochendorfer and Nettles). For the method of Kochendorfer and Nettles, appropriate values of blade-loss parameter ranged from 0.63 to 0.87 and the off-design performance was accurately predicted.

FLOW-TURBINES↗

NASA NTRS1952

An empirically derived basis for calculating the area, rate, and distribution of water-drop impingement on airfoils

An empirically derived basis for predicting the area, rate, and distribution of water-drop impingement on airfoils of arbitrary section is presented. The concepts involved represent an initial step toward the development of a calculation technique which is generally applicable to the design of thermal ice-prevention equipment for airplane wing and tail surfaces. It is shown that sufficiently accurate estimates, for the purpose of heated-wing design, can be obtained by a few numerical computations once the velocity distribution over the airfoil has been determined. The calculation technique presented is based on results of extensive water-drop trajectory computations for five airfoil cases which consisted of 15-percent-thick airfoils encompassing a moderate lift-coefficient range. The differential equations pertaining to the paths of the drops were solved by a differential analyzer.

Bergrun, Norman R↗

NASA NTRS1988

Empirical studies of design software: Implications for software engineering environments

The empirical studies team of MCC's Design Process Group conducted three studies in 1986-87 in order to gather data on professionals designing software systems in a range of situations. The first study (the Lift Experiment) used thinking aloud protocols in a controlled laboratory setting to study the cognitive processes of individual designers. The second study (the Object Server Project) involved the observation, videotaping, and data collection of a design team of a medium-sized development project over several months in order to study team dynamics. The third study (the Field Study) involved interviews with the personnel from 19 large development projects in the MCC shareholders in order to study how the process of design is affected by organizationl and project behavior. The focus of this report will be on key observations of design process (at several levels) and their implications for the design of environments.

Krasner, Herb↗

NASA NTRS1991

BALLIST: A computer program to empirically predict the bumper thickness required to prevent perforation of the Space Station by orbital debris

A computer program called BALLIST that is intended to be a design tool for engineers is described. BALLlST empirically predicts the bumper thickness required to prevent perforation of the Space Station pressure wall by a projectile (such as orbital debris) as a function of the projectile's velocity. 'Ballistic' limit curves (bumper thickness vs. projectile velocity) are calculated and are displayed on the screen as well as being stored in an ASCII file. A Whipple style of spacecraft wall configuration is assumed. The predictions are based on a database of impact test results. NASA/Marshall Space Flight Center currently has the capability to generate such test results. Numerical simulation results of impact conditions that can not be tested (high velocities or large particles) can also be used for predictions.

Rule, William Keith↗

NASA NTRS1994

Space Shuttle orbit determination using empirical force modeling of attitude maneuvers for the German MOMS-02/D2 mission

In the spring of 1993, the MOMS-02 (modular Optoelectronic Multispectral Scanner) camera, as part of the second German Spacelab mission aboard STS-55, successfully took digital threefold stereo images of the surface of the Earth. While the mission is experimental in nature, its primary goals are to produce high quality maps and three-dimensional digital terrain models of the Earth's surface. Considerable improvement in the quality of the terrain model can be attained if information about the position and attitude of the camera is included during the adjustment of the image data. One of the primary sources of error in the Shuttle's position is due to the significant attitude maneuvers conducted during the course of the mission. Various arcs, using actual Tracking and Data Relay Satellite (TDRSS) Doppler data of STS-55, were processed to determine how effectively empirical force modeling could be used to solve for the radial, transverse, and normal components of the orbit perturbations caused by these routine maneuvers. Results are presented in terms of overlap-orbit differences in the three components. Comparisons of these differences, before and after the maneuvers are estimated, show that the quality of an orbit can be greatly enhanced with this technique, even if several maneuvers are present. Finally, a discussion is made of some of the difficulties encountered with this approach, and some ideas for future studies are presented.

Vonbraun, C.↗

NASA NTRS1993

An empirical comparison of a dynamic software testability metric to static cyclomatic complexity

This paper compares the dynamic testability prediction technique termed 'sensitivity analysis' to the static testability technique termed cyclomatic complexity. The application that we chose in this empirical study is a CASE generated version of a B-737 autoland system. For the B-737 system we analyzed, we isolated those functions that we predict are more prone to hide errors during system/reliability testing. We also analyzed the code with several other well-known static metrics. This paper compares and contrasts the results of sensitivity analysis to the results of the static metrics.

Voas, Jeffrey M.↗

NASA NTRS1994

A new approach for determining fully empirical altimeter wind speed model functions

A statistical technique is developed for determining fully empirical model functions relating altimeter backscatter (sigma(sub 0)) measurements to near-surface neutral stability wind speed. By assuming that sigma(sub 0) varies monotonically and uniquely with wind speed, the method requires knowledge only of the separate, rather than joint distribution functions of sigma(sub 0) and wind speed. Analytic simplifications result from using a Weibull distribution to approximate the global ocean wind speed distribution; several different wind data sets are used to demonstrate the validity of the Weibull approximation. The technique has been applied to 1 year of Geosat data. Validation of the new and historical model functions using an independent buoy data set demonstrates that the present model function not only has small overall bias and root mean square (RMS) errors, but yields smaller systematic error trends with wind speed and pseudowave age than previously published models. The present analysis suggests that generally accuracte altimeter model functions can be derived without the use of colocated measurements, nor is additional significant wave height information measured by the altimeter necessary.

Freilich, M. H.↗