Search NASA⌕ Search

SEARCH · Search NASA

Results for “Integral effect test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Modeling and mitigating fouling of microfiltration membranes for microalgae dewatering

Dewatering is energy-intensive for microalgae production, and microfiltration (MF) membranes are attractive because of their high energy efficiency. However, the membranes suffer from fouling by organic matter in the algae solutions, and there needs fundamental understanding of membrane fouling with actual algae solutions. Herein we thoroughly evaluate the dewatering performance of commercial polyethersulfone (PES) MF membranes using an integrated experiment and modeling approach. The effect of algae concentration, testing time, feed flow rate, and chemical cleaning on the dewatering performance and fouling-layer morphology are investigated. The fouling behavior can be successfully described using the Hermia and gel layer models with a gel concentration of 48 g/L for algae solutions. Furthermore, the PES membrane surface was grafted with hydrophilic zwitterions, which mitigated the fouling. For example, when challenged with 10 g/L algae solution in dead-end cells, the pristine and modified membrane exhibit water permeance of 80 and 170 L m – 2 h –1 bar –1 , respectively. Finally, three cycles of dewatering and NaOH cleaning were performed to demonstrate the promise of the MF membranes for practical dewatering application.

42 ENGINEERING↗

Neutrino lumps and the cosmic microwave background

The interaction between the cosmon and neutrinos may solve the 'why now problem' for dark energy cosmologies. Within growing neutrino quintessence it leads to the formation of nonlinear neutrino lumps. For a test of such models by the integrated Sachs-Wolfe effect for the cosmic microwave background (CMB) we estimate the size and time evolution of the gravitational potential induced by these lumps. A population of lumps with size of 100 Mpc or more could lead to observable effects on the CMB anisotropies for low angular momenta. The linear approximation is found to be invalid for the relevant length scales. Quantitative estimates depend strongly on the details of the transition between the linear and nonlinear regimes. In particular, important backreaction effects arise from the nonlinearities of the cosmon interactions. At the present stage the uncertainties of the estimate make it difficult to constrain the parameter space of growing neutrino models. We explicitly discuss scenarios and models that are compatible with the CMB observations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Apollo experience report: Manned thermal-vacuum testing of spacecraft

Manned thermal-vacuum tests of the Apollo spacecraft presented many first-time problems in the areas of test philosophy, operational concepts, and program implementation. The rationale used to resolve these problems is explained and examined critically in view of actual experience. The series of 12 tests involving 1517 hours of chamber operating time resulted in the disclosure of numerous equipment and procedural deficiencies of significance to the flight mission. Test experience and results in view of subsequent flight experience confirmed that thermal-vacuum testing of integrated manned spacecraft provides a feasible, cost-effective, and safe technique with which to obtain maximum confidence in spacecraft flight worthiness early in the program.

Mclane, J. C., Jr.↗

Interim review of the Energy Efficient Engine /E3/ Program

The NASA-sponsored Energy Efficient Engine (E3) Program, which is now in its fourth year, is assessed from the viewpoint of one of its research contractors. Attention is given to the development status of the shroudless fan, segmented combustor and exhaust mixer components which are encompassed by the program. The shroudless fan blades are two-thirds hollow for lightness, and are fabricated by means of plies and cores subjected to hot isostatic pressing diffusion bonding. The combustor's segmented liner is cast from turbine blade materials. Exhaust mixer flow visualization tests are described. Consideration is given to the effects of integrating the technology described with the low and high pressure advanced turbines whose development is also part of the E3 program.

Gardner, W. B.↗

Simulation and control of a Space Station air revitalization system

A computer simulation tool is written to investigate simulation and control of a Space Station air revitalization system. Candidate subsystems for various air revitalization roles in the Space Station have been and continue to be tested. However, integration and control of these subsystems into an effective system which revitalizes the air in all habitable areas needs to be evaluated. From such an evaluation, the size of subsystems, size and location of accumulators, and decisions on bussing of carbon dioxide, hydrogen, oxygen, and nitrogen can be affected. In addition, various control approaches can be assessed. The computer simulation model is described and its applications are presented.

Yanosy, James L.↗

Cross-Quint-Bridge Resistor

Integrated-circuit conductive test pattern intended to provide data on effects of design widths and design spacings upon actual widths of conductive lines. Provides for electrical measurements both on lines of unknown width and on features having known dimensions. Data from measurements on five bridges used to determine four parameters of mathematical model describing system. In principle, pattern determines effects of width and spacing and interaction between them.

Hannaman, David J.↗

A simulation facility for testing Space Station assembly procedures

NASA plans to construct the Space Station Freedom (SSF) in one of the most hazardous environments known to mankind - space. It is of the utmost importance that the procedures to assemble and operate the SSF in orbit are both safe and effective. This paper describes a facility designed to test the integration of the telerobotic systems and to test assembly procedures using a real-world robotic arm grappling space hardware in a simulated microgravity environment.

Hajare, Ankur R.↗

Opportunities for wave energy in bulk power system operations

Wave energy resources have high, yet largely untapped potential as candidate generation technology. In this paper, we perform a data-driven analysis to characterize the impact of wave energy integration on bulk-scale power systems and market operations. Through data-driven sensitivity studies centered on an optimization-based production cost modeling formulation, our work characterizes the inflection point beyond which wave integration starts impacting power system operations, considering present day transmission infrastructure. Furthermore, our analysis also considers the joint effects of wave energy integration and system-wide transmission expansion. Finally, potential resilience scenarios such as wildfire-driven transmission contingencies and heat wave events are investigated, whereby the contributions of grid-integrated wave energy in alleviating the effects of the resilience events are analyzed. As our demonstration test bed, we consider a reduced-order network topology for the U.S. Western Interconnection with wave energy generation integrated at carefully selected sites across the coastal areas of Washington, Oregon, and northern California. Our results indicate that over a representative year of operations, wave energy integration systematically reduces locational marginal prices (LMPs) of energy and price volatility, especially during periods of high wave resource availability (winter months for the U.S. west coast). Average, maximum, and minimum of hourly LMPs over a typical year of operation was reduced by 2.95, 51.28, and 1.13 $\$$/MWh respectively (over a baseline scenario with no wave energy integration), when the selected network model had a total of 5000 MW wave power installed capacity during the representative year of study. The effects of wave energy integration can remain localized with existing transmission infrastructure (identified to be most pronounced in the Pacific Northwest region in the example we studied). However, with concurrent transmission expansion, the impacts of wave energy integration are likely to have a higher geographical spread. Our results also indicate that wave energy may be able to assist power system operations during resilience events such as major transmission contingencies and heat wave events, although such benefits might be dependent on factors such as proximity of affected area to wave resources, availability of adequate resource potential and adequate transmission capacity.

16 TIDAL AND WAVE POWER↗

De-icing: recovery of diffraction intensities in the presence of ice rings

Macromolecular structures are routinely determined at cryotemperatures using samples flash-cooled in the presence of cryoprotectants. However, sometimes the best diffraction is obtained under conditions where ice formation is not completely ablated, with the result that characteristic ice rings are superimposed on the macromolecular diffraction. In data processing, the reflections that are most affected by the ice rings are usually excluded. Here, an alternative approach of subtracting the ice diffraction is tested. High completeness can be retained with little adverse effect upon the quality of the integrated data. This offers an alternate strategy when high levels of cryoprotectant lead to loss of crystal quality.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Energy Efficient Clothes Dryer with IR Heating and Electrostatic Precipitator

The project goal was to develop a revolutionary energy saving technology for residential clothes drying. The team developed an IR (infrared) heating system and NESP (Nebulizer and Electro-Static Precipitator) for integration into a ventless clothes dryer. The proposed technology addresses two of the major inefficiencies in current electric vented dryers by providing effective energy transfer for the removal of the water and recapture of the vapor latent heat. The IR heaters operating in the mid wave (2.5-10um) are very efficient as they target the 3-micron peak absorption of the water molecule. This allows direct energy absorption, unlike conventional element heaters where heat is transferred by convection. The low power NESP removes water vapor from the exhausted stream and recaptures the latent heat in the ESP (Electro-Static Precipitator) exchanger section. This allows the warm dry air to be recirculated back into the drum for additional efficiency savings. The remaining majority of the dryer hardware stays the same. Summing the efficiency gain from the two subcomponents we anticipated the EF (Efficiency Factor) to exceed the goal of 4.04. EF is obtained by dividing the weight (lbs) of water removed by the energy (kWhr) used, where the test load size is 8.45 lbs of bone dry clothing wetted to 57.5% or 4.8lbs of water, and dried to a remaining moisture content of 2.5-5%. Additional benefits include not having to recondition (heat or cool) the large amounts of make-up air to replace the air exhausted by a vented dryer. It was anticipated that the NESP/heat exchanger would be the most challenging and highest risk element in the program. Therefore, the team focused their efforts during Phase 1 of the program on the design, construction, testing, and optimization of the NESP/heat exchanger. At the end Phase 1, the team compared the performance of the NESP/heat exchanger with the system level requirements and made a Go/No-Go decision on proceeding with the second portion of the program. Phase 2 of the program was structured to develop the IR heating system and then integrate it and the NESP/heat exchanger into a residential clothes dryer prototype for final testing. The proposed technology utilizes heat recovery which is known to have the biggest impact on dryer efficiency. The two current mainstream recovery approaches are air to air exchangers and heat pump condenser systems. Air to air exchanges can be very efficient but require large surface areas which are prone to fouling from uncaptured lint. Dryers based on heat pump condenser recovery systems have shown efficiency improvements of 20–60% and are commercially available. The issue with a heat pump condenser approach is the added cost, as typical prices are twice that of standard vented dryers and they are only available in small to medium capacities. The energy factor (EF) for these systems is 5.50 to 6.88 pounds/kWh compared to conventional dryers at 2.75 to 3.67 pounds/kWh. The efficiency improvements for the proposed technology come from the use of IR heating and the NESP. As the concept is in its infancy, and these improvements were difficult to predict without experimental data, assumptions were made based on available literature. IR radiant drying times, when compared to convection, are typically 30% less. This is a result of the fact that radiant energy heats directly and is absorbed at and below the surface, unlike convection heating, that must conduct the heat through the boundary film of air at the clothes surface and rely on wicking of the moisture to the surface. The second area of improvement comes from the NESP. The NESP operation is as follows: 1. Highly charged, micron sized, droplets of water are injected into the dryer exhaust by the Nebulizer. 2. These charged droplets attract water molecules and continue to grow in size, until losing their charge. During this process, latent heat is rejected back into the air stream. 3. The large droplets enter the ESP, where they are recharged and drawn to the ESP wall, to be extracted at the bottom of the ESP. The warm dry air is then recirculated back into the dryer. The proposed technology, at the time of the proposal submission was estimated to have an EF of 4.79. At program completion we have designed, built, tested, integrated and optimized the proposed technologies into a prototype “high efficiency” residential clothes dryer. Testing of the integrated prototype dryer provided insight into the technical effectiveness and economic feasibility of the proposed technologies. The program has the potential of greatly impacting energy savings. The predicted EF of the proposed technology is 4.79, yielding an energy savings of 42% when compared to conventional electric vented dryers. Given there are approximately 84 million dryers in the US consuming ~64 billion kWh per year, a net savings of 27 billion kWh per year or 0.092 quads could be realized. Since the dryer is not vented, make up air from the room is not needed, adding an additional savings of ~1kWh per load, or 23.8 billion kWh per year. In addition, it is envisioned that the proposed ESP, when successful, would potentially find applications in industrial and residential dehumidification.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Single event test methodology for integrated optoelectronics

A single event upset (SEU), defined as a transient or glitch on the output of a device, and its applicability to integrated optoelectronics are discussed in the context of spacecraft design and the need for more than a bit error rate viewpoint for testing and analysis. A methodology for testing integrated optoelectronic receivers and transmitters for SEUs is presented, focusing on the actual test requirements and system schemes needed for integrated optoelectronic devices. Two main causes of single event effects in the space environment, including protons and galactic cosmic rays, are considered along with ground test facilities for simulating the space environment.

Label, Kenneth A.↗

Single Event Effects Testing of the Linfinity SG1525A Pulse Width Modulator Controller

Pulse Width Modulator (PWM) Controllers are the heart of switching power supply systems in development today. The PWMs considered here have the same integration advantages as many other controllers but it also includes the interface drivers for the follow-on power Field Effect Transistors (FET). Previous work on these types of devices looked into the required test methodologies [ 11 and the impact of radiation on the soft start and shutdown circuits of typically incorporated in the technology [2]. Taking advantage of this previous work this study was undertaken to determine the single event destructive and transient susceptibility of the Linfinity SG1525A Pulse Width Modulator Controller. The device was monitored for transient interruptions in the output signals and for destructive events induced by exposing it to a heavy ion beam at the Texas A&M University Cyclotron Single Event Effects Test Facility. After exposing these devices to the beam, a new upset mode has been identified that can lead to catastrophic power supply system failure if this event would occur while drive power FETs off the two device outputs. The devices and the test methods used will be described first. This will be followed by a brief description of the data collected to date (not all data can be presented with the length constraints of the summary) and a summary of the key results.

Howard, J. W., Jr.↗

A Collisional Algorithm for Modeling Circumstellar Debris Disks

Many planetary systems harbor circumstellar disks of dust and planetesimals thought to be debris left over from planet formation. These debris disks exhibit a range of morphological features which can arise from the gravitational perturbations of planets. Accurate models of these features, accounting for the interactions of the particles in a disk with each other and with whatever planets they contain, can act as signposts for planets in debris disks that otherwise could not be detected. Such models can also constrain the planet's mass and orbital parameters. Current models for many disks consider the gravitational and radiative effects of the star and planets on the disk, but neglect the morphological consequences of collisional interactions between the planetesimals. Many observed disk features are not satisfactorily explained by the current generation of models. I am developing a new kind of debris disk model that considers both the gravitational shaping of the disk by planets and the inelastic collisions between particles. I will use a hybrid N-body integrator to numerically solve the equations of motion for the particles and planets in the disk. To include the collisional effects, I begin with an algorithm that tests for collisions at each step of the orbit integration and readjusts the velocities of colliding particles. I am adapting this algorithm to the problem at hand by allowing each particle to represent a "swarm" of planetesimals with a range of masses. When the algorithm detects an encounter between swarms, two or three swarms are produced to approximate the range of possible trajectories of the daughter planetesimals. Here I present preliminary results from my collisional algorithm.

Nesvold, Erika↗

Adaptive time-stepping Monte Carlo integration of Coulomb collisions

Here, we report an accessible and robust tool for evaluating the effects of Coulomb collisions on a test particle in a plasma that obeys Maxwell–Jüttner statistics. The implementation is based on the Beliaev–Budker collision integral which allows both the test particle and the background plasma to be relativistic. The integration method supports adaptive time stepping, which is shown to greatly improve the computational efficiency. The Monte Carlo method is implemented for both the three-dimensional particle momentum space and the five-dimensional guiding center phase space.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Results of tests in the MSFC 14 x 14 inch trisonic wind tunnel on a .004 scale model of the Rockwell International Space Shuttle Vehicle 3, (integrated configuration)

Experimental aerodynamic investigations were conducted during mid-July, 1973 on a .004 scale model of the Rockwell International integrated configuration Space Shuttle Vehicle 3. The purpose of the tests was three fold: (1) to determine the static stability characteristics of the integrated vehicle, utilizing the Vehicle 3 orbiter configuration; (2) to determine the effect of interstage structure and tank external fuel lines on the integrated vehicle aerodynamic characteristics; (3) to determine the effects of the aft interstage structure on orbiter aerodynamic loads. Data were recorded on the integrated vehicle (test no. 579) at angles of attack and sideslip ranging from -10 deg to 10 deg over a Mach number schedule from 0.6 to 4.96. Data were obtained on the orbiter alone in the presence of the external tank with SRB attached (test no. 580) at angles of attack from -10 deg to 10 deg over a Mach number range from .6 to 1.96. Plotted data are presented in the body axis system.

Allen, E. C.↗

UAS-NAS Flight Test Series 3: Test Environment Report

The desire and ability to fly Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS) is of increasing urgency. The application of unmanned aircraft to perform national security, defense, scientific, and emergency management are driving the critical need for less restrictive access by UAS to the NAS. UAS represent a new capability that will provide a variety of services in the government (public) and commercial (civil) aviation sectors. The growth of this potential industry has not yet been realized due to the lack of a common understanding of what is required to safely operate UAS in the NAS. NASA's UAS Integration in the NAS Project is conducting research in the areas of Separation Assurance/Sense and Avoid Interoperability (SSI), Human Systems Integration (HSI), and Communications (Comm), and Certification to support reducing the barriers of UAS access to the NAS. This research is broken into two research themes namely, UAS Integration and Test Infrastructure. UAS Integration focuses on airspace integration procedures and performance standards to enable UAS integration in the air transportation system, covering Detect and Avoid (DAA) performance standards, command and control performance standards, and human systems integration. The focus of Test Infrastructure is to enable development and validation of airspace integration procedures and performance standards, including integrated test and evaluation. In support of the integrated test and evaluation efforts, the Project will develop an adaptable, scalable, and schedulable relevant test environment capable of evaluating concepts and technologies for unmanned aircraft systems to safely operate in the NAS. To accomplish this task, the Project is conducting a series of human-in-the-loop (HITL) and flight test activities that integrate key concepts, technologies and/or procedures in a relevant air traffic environment. Each of the integrated events will build on the technical achievements, fidelity, and complexity of the previous tests and technical simulations, resulting in research findings that support the development of regulations governing the access of UAS into the NAS. The integrated events started with two initial flight test used to develop and test early integrations and components of the test environment. Test subjects and a relevant test environment were brought in for the integrated HITL (or IHITL) conducted in 2014. The IHITL collected data to evaluate the effectiveness of DAA Well Clear (DWC) algorithms and the acceptability of UAS concepts integrated into the NAS. The first integrated flight test (and the subject of this report) followed the IHITL by replacing the simulation components with live aircraft. The project finishes the integrated events with a final flight test to be conducted in 2016 that provides the researchers with an opportunity to collect DWC and Collision Avoidance (CA) interoperability data during flight encounters.

flight test↗

Proton Testing of AMD Ryzen 3 2200G Microprocessors

Single-Event Effects (SEE) testing was conducted on the AMD Ryzen 3 2200G microprocessor with integrated graphics. Testing was conducted at Massachusetts General Hospital's (MGH) Francis H. Burr Proton Therapy Center on June 2nd, 2019.

radiation tesing↗

Investigation of two-dimensional wedge exhaust nozzles for advanced aircraft

Two-dimensional wedge nozzle performance characteristics were investigated in a series of wind-tunnel tests. An isolated single-engine/nozzle model was used to study the effects of internal expansion area ratio, aftbody cowl boattail angle, and wedge length. An integrated twin-engine/nozzle model, tested with and without empenage surfaces, included cruise, acceleration, thrust vectoring and thrust reversing nozzle operating modes. Results indicate that the thrust-minus-aftbody drag performance of the twin two-dimensional nozzle integration is significantly higher, for speeds greater than Mach 0.8, than the performance achieved with twin axisymmetric nozzle installations. Significant jet-induced lift was obtained on an aft-mounted lifting surface using a cambered wedge center body to vector thrust. The thrust reversing capabilities of reverser panels installed on the two-dimensional wedge center body were very effective for static or in-flight operation.

Maiden, D. L.↗