Search NASA⌕ Search

SEARCH · Search NASA

Results for “Salt Dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Compatibility of Type 304H Stainless Steel in Static Molten FLiBe for Inertial Confinement Fusion Reactors: Role of Impurities and Redox Control

Molten fluoride salts, such as FLiBe (LiF-BeF2), are promising candidates for tritium breeding and heat transfer in fusion reactors, but corrosion of structural materials remains a major challenge. This study investigates the corrosion behavior of austenitic stainless steel 304H in purified and NiF2-containing FLiBe at 500°C and 600°C, focusing on the effects of impurities and redox control. Exposure to purified FLiBe resulted in the concurrent depletion of Cr, Mn, and Fe, with corrosion at 500 °C dominated by the combined oxide formation and elemental dissolution, while at 600°C elemental depletion was predominant. The addition of a controlled NiF2 impurity significantly accelerated corrosion at both temperatures, demonstrating the sensitivity of 304H to the salt redox state. Beryllium additions were effective in mitigating corrosion for both baseline and NiF2-containing FLiBe; minimal depletion of Cr, Mn, and Fe occurred with Be additions as low as 2.5 mg (147 wppm), and no NiBe intermetallics formed at 5 mg (294 wppm), indicating that small Be inventories can provide substantial protection without deleterious phase formation. Thermodynamic equilibrium and coupled thermodynamic-kinetic analyses at the salt-alloy interface suggested low corrosion rates in systems with limited hydrogen fluoride (HF) generation, highlighting the importance of salt redox control. Estimates for a Be addition rate were calculated for the HYLIFE-II fusion reactor that can mitigate corrosion-induced degradation, assuming complete conversion of tritium to tritium fluoride (TF). Overall, 304H shows reasonable compatibility with FLiBe under optimized redox conditions. These results provide quantitative guidance for material selection and salt management in fusion blanket and heat exchanger systems and motivate validation under flowing, nonisothermal, and irradiated conditions.

Pillai, Rishi [ORNL] (ORCID:0000000243688197)↗

Optimizing a chemical cleaning protocol to determine the nickel isotopic composition of ancient seawater from carbonates

Reconstructing the ancient marine cycle of Ni, a trace metal in the oceans essential to enzymes regulating the C, N, and O cycles, would inform how Ni bioavailability shaped early life. The Ni isotopic composition of seawater (δ 60 Ni SW ) through time could provide insight, but this approach requires sedimentary archives that faithfully record δ 60 Ni SW . Carbonates are an often-used record of seawater chemistry, but contaminants could bias the measured δ 60 Ni of bulk sediment. To isolate the true carbonate-bound δ 60 Ni signal, we optimized a chemical cleaning protocol designed to minimize non‑carbonate Ni contributions and maximize carbonate recovery. We analyzed ODP Site 1007 sediments and evaluated oxidative and reductive pre-cleaning steps and carbonate dissolution protocols. Our results show that only reductive cleaning significantly altered the subsequent carbonate leachate composition, lowering Ni/Ca ratios by up to 60% and δ 60 Ni values by as much as 0.4 ‰. In contrast, δ 60 Ni values were largely insensitive to premature carbonate dissolution during pre-cleaning or to partial leaching of silicates during carbonate dissolution, even at higher acid molarities or longer reaction times. We recommend an evidence-based protocol that removes hydro-soluble salts and clays, applies reductive cleaning and oxidative cleaning for certain sample compositions, and dissolves carbonate using 0.5 M acetic acid, adjusted to pH 5. Using these results, we infer a ∼ 0.9 ‰ Ni isotopic fractionation between chemically cleaned deep-water carbonates (+0.4 ± 0.1 ‰) and deep seawater. This method development is a key step toward accurately reconstructing ancient marine Ni cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Anion Mobility on Electrochemical Behaviors of Lithium–Sulfur Batteries

The electrolyte is a crucial component of lithium-sulfur (Li-S) batteries, as it controls polysulfide dissolution, charge shuttling processes, and solid-electrolyte interphase (SEI) layer formation. Experimentally, the overall performance of Li-S batteries varies with choice of solvent system and Li-salt used in the electrolyte, and a lack of predictive understanding about the effects of individual electrolyte components inhibits the rational design of electrolytes for Li-S batteries. Here we analyze the role of the counter anions of common Li salts (such as TfO-, FSI-, TFSI-, and TDI-) when dissolved in DOL/DME (1:1 vol.) for use in Li-S batteries. The evolution of ion-ion and ion-solvent interactions due to vari-ous anions was analyzed using 17O NMR and pulsed-field gradient (PFG) NMR and then correlated with electrochemi-cal performance in Li-S cells. These data reveal that the for-mation of the passivation layer on the anode and the loss of active materials from the cathode (evidenced by polysulfide dissolution) are related to anion mobility and affinity with lithium polysulfide, respectively. For future electrolyte de-sign, anions with lower mobility and weaker interactions with lithium polysulfides may be superior candidates for increasing the long-term stability of Li-S batteries.

25 ENERGY STORAGE↗

Industrial Scale-Up of Low-Cost Zero-Emissions Magnesium by INFINIUM Electrolysis

INFINIUM led a project whose goal was at first to produce pure magnesium, and later magnesium-rare earth alloys, directly from oxides. The reduction technology is molten salt electrolysis with a fluoride salt bath, similar to the Hall-Héroult process for aluminum. The pure magnesium component of the project used novel oxygen-producing anodes with a zirconia solid electrolyte tube between the molten salt and anode. The project later shifted to direct production of magnesium-neodymium master alloy for Mg-rare earth alloys. These alloys are typically made by dissolution of rare earth metals into magnesium, and cost over six times the rare earth basis price of the master alloy. The resulting process produced a total of over 30 kg of Mg-Nd master alloy, which was made into nearly 250 kg of AE42 (Mg-4%Al-2%Nd) alloy.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Dissolution of Lithium Metal in Poly(ethylene oxide)

We observe that lithium metal is sparingly soluble in poly(ethylene oxide) (PEO). 7 Li NMR shows that when a PEO sample is placed in contact with lithium metal at elevated temperatures, a lithium species dissolves and diffuses into the bulk polymer. A lithium/PEO/lithium electrochemical cell, containing no lithium salts, shows increasing conductivity over time when annealed at 120 °C. Chronoamperometry shows that the annealed cell obeys Ohm's law, implying that conduction occurs without the development of concentration gradients. To explain the findings, it is proposed that atomic lithium dissolves into PEO, where it exists as a lithium cation and free electron. The dissolution of lithium also affects the phase behavior of block copolymer electrolytes. These determinations explain the strong adhesion between lithium metal and PEO and have important implications for lithium metal battery systems that contain PEO-based electrolytes.

25 ENERGY STORAGE↗

Microscale THMC Modeling of Pressure Solution in Salt Rock: Impacts of Geometry and Temperature

Abstract Pressure solution, a mechanism that involves tight coupling between the geometry and thermal-hydro-mechanical-chemical (THMC) processes, plays an important role in diagenesis. In this study, we make the first attempt to conduct microscale THMC modeling to understand and quantify the impacts of geometry and temperature on pressure solution, taking natural salt rock as an example. This modeling capability is achieved by expanding a novel MC code that we developed previously (Hu et al. J Geophys Res: Solid Earth 126:e2021JB023112, 2021) to include temperature effects. We first conduct a simulation of an example that involves a single brine inclusion within a single halite grain and find that the temperature impact is limited for that case. We then extract geometry from an image of a natural salt rock and conduct simulations with different cases: (A) only temperature and no stress, (B) only stress and no temperature, and (C) with both stress and temperature. These different cases result in quite different phenomena. In case A, dissolution and precipitation occur across the entire system due to isolated pore space reaching a localized mass balance between dissolution, precipitation, and diffusion. In case B, intense geometric features (e.g., major asperities, inclusions) in one area undergo stress concentration, thus dominating pressure solution in that area. In case C, pressure solution is spread out at contacting highly stressed geometric features close to the hotter side. We conclude that geometric features dominate stress distribution, thus dominating pressure solution in a natural salt rock that may be affected by the temperature if a sufficient temperature gradient is applied.

58 GEOSCIENCES↗

SLUDGE HEEL REMOVAL BY ALUMINUM DISSOLUTION AT SAVANNAH RIVER SITE 12390

High Level Waste (HLW) at the Savannah River Site (SRS) is currently stored in aging underground storage tanks. This waste is a complex mixture of insoluble solids, referred to as sludge, and soluble salts. Continued long-term storage of these radioactive wastes poses an environmental risk. Operations are underway to remove and disposition the waste, clean the tanks and fill with grout for permanent closure. Heel removal is the intermediate phase of the waste retrieval and tank cleaning process at SRS, which is intended to reduce the volume of waste prior to treatment with oxalic acid. The goal of heel removal is to reduce the residual amount of radioactive sludge wastes to less than 37,900 liters (10,000 gallons) of wet solids. Reducing the quantity of residual waste solids in the tank prior to acid cleaning reduces the amount of acid required and reduces the amount of excess acid that could impact ongoing waste management processes. Mechanical heel removal campaigns in Tank 12 have relied solely on the use of mixing pumps that have not been effective at reducing the volume of remaining solids. The remaining waste in Tank 12 is known to have a high aluminum concentration. Aluminum dissolution by caustic leaching was identified as a treatment step to reduce the volume of remaining solids and prepare the tank for acid cleaning. Dissolution was performed in Tank 12 over a two month period in July and August, 2011. Sample results indicated that 16,440 kg of aluminum oxide (boehmite) had been dissolved representing 60% of the starting inventory. The evolution resulted in reducing the sludge solids volume by 22,300 liters (5900 gallons), preparing the tank for chemical cleaning with oxalic acid.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Exploring Fission–Fusion Synergies to Accelerate Compatibility Understanding

To address the significant commercial interest in fusion energy, it will be necessary to accelerate the compatibility research associated with liquid breeders including Li, eutectic Pb–Li and LiF-BeF 2 (FLiBe) molten salt. Particularly for FLiBe, compatibility understanding is limited especially for fusion relevant materials such as reduced activation ferritic-martensitic steels, SiC and V alloys. The historical knowledge associated with molten salt reactors (MSRs) and recent work to commercialize MSRs can benefit fusion research. Recent experimental and modeling work has improved understanding and this knowledge can be applied to fusion relevant materials. For liquid metals (LMs), the comparisons to Li and Pb–Li are less direct but nevertheless can help guide the pathway toward commercialization. For Pb–Li, Al-rich coatings have been shown to inhibit dissolution and potentially increase operating temperatures. For commercialization, the experience with sensors and on-line cleanup can help guide future developments. Thus, it is worth considering the potential for fission-related research with LMs and molten salts to help accelerate fusion research.

36 MATERIALS SCIENCE↗

One-step through-mask electrodeposition of a porous structure composed of manganese oxide nanosheets with electrocatalytic activity for oxygen reduction

Potentiostatic electrolysis of a mixed aqueous solution of Bu{sub 4}NBr and MnSO{sub 4} at +1.0 V (vs. Ag/AgCl) on Pt electrode led to the oxidation of Br{sup -} and Mn{sup 2+} ions. X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and X-ray diffraction (XRD) revealed that this anodic process was followed by the deposition of insulating crystals of bromide salt of Bu{sub 4}N{sup +} and the subsequent formation of layered manganese oxide in the interstitial spaces of the bromide grains already grown. Dissolution of the bromide crystals in water left a well-dispersed porous texture composed of manganese oxide nanosheets. The resulting MnO{sub x}-modified electrode exhibited a larger catalytic current for the reduction of oxygen in alkaline solution, compared to the bare Pt electrode.

36 MATERIALS SCIENCE↗

Electrolyte Study for High-Nickel LiNi 0.9 Mn 0.05 Co 0.05 O 2 Cathodes

With an increasing demand for intermittent renewable energy and electric vehicles, it is imperative to develop lithium-ion batteries with Earth-abundant cathode materials. Cobalt (Co) is preferred to be kept at a minimum because of its high cost and limited mining options, yet it has played an essential role in the high-performance transition metal oxides (TMOs). Herein, we report work from Argonne National Laboratory, conducted under the U.S. DoE's Vehicle Technologies Office, Deep Dive consortium on Next-Generation Cathodes, to optimize electrolytes for LiNi 0.9 Mn 0.05 Co 0.05 O 2 . LiNi 0.9 Mn 0.05 Co 0.05 O 2 is a high-Ni TMO benchmark as it outperforms most other TMOs under standard cycling conditions. In this study, we use the figure-of-merit approach to optimize electrolytes for this novel cathode material. Dual-salt carbonate electrolytes containing lithium difluorooxyphosphate and hexafluorophosphates were found to be the best for capacity retention and slowing the impedance rise. Importantly, transition metal dissolution and lithium inventory losses in the solid electrolyte interface were found to be the major causes for capacity fade.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Sodium Carboxymethyl Celluloses on Water-catalyzed Self-degradation of 200°C-heated Alkali-Activated Cement

We investigated the usefulness of sodium carboxymethyl celluloses (CMC) in promoting self-degradation of 200°C-heated sodium silicate-activated slag/Class C fly ash cementitious material after contact with water. CMC emitted two major volatile compounds, CO 2 and acetic acid, creating a porous structure in cement. CMC also reacted with NaOH from sodium silicate to form three water-insensitive solid reaction products, disodium glycolate salt, sodium glucosidic salt, and sodium bicarbonate. Other water-sensitive solid reaction products, such as sodium polysilicate and sodium carbonate, were derived from hydrolysates of sodium silicate. Dissolution of these products upon contact with water generated heat that promoted cement’s self-degradation. Thus, CMC of high molecular weight rendered two important features to the water-catalyzed self-degradation of heated cement: One was the high heat energy generated in exothermic reactions in cement; the other was the introduction of extensive porosity into cement.

15 GEOTHERMAL ENERGY↗

Mineral dissolution by dimeric complexes

Mineral dissolution is typically thought to occur by the detachment of monomeric building blocks of the crystal structure, although direct evidence is rare. Using in situ high-speed atomic force microscopy to examine step-edge retreat dynamics at high resolution, we report that the dissolution of gibbsite in alkaline solutions occurs mainly by the release of aluminate dimers, which subsequently dissociate into the monomeric species that dominate the solution. Here, the observed dissolution anisotropy is readily explained by this mechanism, which was further supported by density functional tight-binding simulations of detachment activation energies. Recognition that such polynuclear dissolution mechanisms exist may enable an improved understanding of processes regulating mineral dissolution rates in nature and industry.

atomic force microscopy↗

Head-end process for the reprocessing of HTGR spent fuel

The reprocessing of HTGR spent fuels is in favor of the sustainable development of nuclear energy to realize the maximal use of nuclear resource and the minimum disposal of nuclear waste. The head-end of HTGR spent fuels reprocessing is different from that of the LWR spent fuels reprocessing because of the difference of spent fuel structure. The dismantling of the graphite spent fuel element and the highly effective dissolution of fuel kernel is the most difficult process in the head end of the reprocessing. Recently, some work on the head-end has been done in China. First, the electrochemical method with nitrate salt as electrolyte was studied to disintegrate the graphite matrix from HTGR fuel elements and release the coated fuel particles, to provide an option for the head-end technology of reprocessing. The results show that the graphite matrix can be effectively separated from the coated particle without any damage to the SiC layer. Secondly, the microwave-assisted heating was applied to dissolve the UO{sub 2} kernel from the crashed coated fuel particles. The ceramic UO{sub 2} as the solute has a good ability to absorb the microwave energy. The results of UO{sub 2} kernel dissolution from crushed coated particles by microwave heating show that the total dissolution percentage of UO{sub 2} is more than 99.99% after 3 times cross-flow dissolution with the following parameters: 8 mol/L HNO{sub 3}, temperature 100 Celsius degrees, initial ratio of solid to liquid 1.2 g/ml. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Tailoring Solvation Solvent in Localized High-Concentration Electrolytes for Lithium||Sulfurized Polyacrylonitrile

Sulfurized polyacrylonitrile (SPAN) is a promising cathode material for lithium-sulfur (Li-S) batteries due to its significantly reduced polysulfide (PS) dissolution compared to the elemental S cathode. Although conventional carbonate-based electrolytes is stable with SPAN electrodes, it is less stable with Li metal anode (LMA). Recently, localized high-concentration electrolytes (LHCEs) have been developed to improve the stability of LMA. Here, we report a new strategy to further improve the performance of LI||SPAN batteries by replacing the conventional solvating solvent 1,2-dimethoxyethane (DME) in the LHCE with a new solvating solvent, 1,2-diethoxyethane (DEE), the new LHCEs exhibits less reactivity against Li 2 S 2 , alleviates PS dissolution, forms a better cathode-electrolyte interphase layer on the SPAN, and enhances structure reversibility even at elevated temperature (ET, 45°C). With the same salt and diluent as in other LHCEs, the LHCE with DEE leads to better performance in Li||SPAN batteries (with 82.9% capacity retention after 300 cycles at ET), preservation of SPAN cathode structure, and suppression of the volume change of LMA. The similar strategy on tailoring the solvating solvents in LHCEs can also be used in other rechargeable batteries to improve their performances.

1,2-diethoxyethane↗

Review—Electrolytic Metal Atoms Enabled Manufacturing of Nanostructured Sensor Electrodes

Sensing materials play a key role in the successful implementation of electrochemical sensors, and nanotechnology has emerged as an important and rapidly growing field for stimulating the innovation of high-performance sensors. The fabrication, characterization, and evaluation of the nanostructured electrodes are therefore a focus of this field. Compared to a variety of dry and wet technologies which have been extensively developed for this purpose, electrochemical methods are typically convenient, highly effective, and potentially low-cost for the production of different nanostructures. This minireview is designed to introduce a unique electrochemical method - electrolytic metal-atom enabled manufacturing (EM 2 ) and its application in electrochemical sensors. The EM 2 technique employs electrolytic metal atoms generated from their corresponding salt precursor as a tool to nanostructure a wide range of substrate electrodes used in electrochemical sensors, based on a one-pot electrochemical deposition and dissolution of the metal atoms in the same electrolyte bath. Briefly, the metal atoms are electrodeposited on a substrate electrode during the cathode reduction, and they are selectively removed from the substrate during the subsequent anode oxidation. Because of the interactions between the electrolytic metal atoms and the substrate atoms, the repetitive electrodeposition and dissolution of the former on the substrate enable the nanostructuration of the substrate, particularly within its surface layers. The nanostructured electrodes have demonstrated very attractive performance for the determination of numerous analytes, such as high sensitivity and selectivity, high interference tolerance, and low detection limits. However, the EM 2 technique and the application of the resulting nanostructured electrodes in electrochemical sensors and beyond have still been very limitedly investigated. In order to bring the community from academic, industries, agencies, and customers together to develop the EM 2 technique and advance electrochemical sensor systems, this minireview will introduce the thermodynamic and kinetic fundamentals of this technique, the characterization of resulting nanostructures, the analysis of their electrochemical behavior, and the implementation of this technique for the development of advanced sensor electrodes. Finally, an outlook with a focus on further research areas is provided.

Jiang, Junhua (ORCID:0000000324379812)↗

Organic oxalate as leachant and precipitant for the recovery of valuable metals from spent lithium-ion batteries

Graphical abstract: Display Omitted Highlights: Black-Right-Pointing-Pointer Vacuum pyrolysis as a pretreatment was used to separate cathode material from aluminum foils. Black-Right-Pointing-Pointer Cobalt and lithium can be leached using oxalate while cobalt can be directly precipitated as cobalt oxalate. Black-Right-Pointing-Pointer Cobalt and lithium can be separated efficiently from each other only in the oxalate leaching process. Black-Right-Pointing-Pointer High reaction efficiency of LiCoO{sub 2} was obtained with oxalate. - Abstract: Spent lithium-ion batteries containing lots of strategic resources such as cobalt and lithium are considered as an attractive secondary resource. In this work, an environmentally compatible process based on vacuum pyrolysis, oxalate leaching and precipitation is applied to recover cobalt and lithium from spent lithium-ion batteries. Oxalate is introduced as leaching reagent meanwhile as precipitant which leaches and precipitates cobalt from LiCoO{sub 2} and CoO directly as CoC{sub 2}O{sub 4}{center_dot}2H{sub 2}O with 1.0 M oxalate solution at 80 Degree-Sign C and solid/liquid ratio of 50 g L{sup -1} for 120 min. The reaction efficiency of more than 98% of LiCoO{sub 2} can be achieved and cobalt and lithium can also be separated efficiently during the hydrometallurgical process. The combined process is simple and adequate for the recovery of valuable metals from spent lithium-ion batteries.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Thermal behavior of polyhalite: a high-temperature synchrotron XRD study

As an accessory mineral in marine evaporites, polyhalite, K 2 MgCa 2 (SO 4 ) 4 ·2H 2 O, coexists with halite (NaCl) in salt formations, which have been considered as potential repositories for permanent storage of high-level nuclear wastes. However, because of the heat generated by radioactive decays in the wastes, polyhalite may dehydrate, and the released water will dissolve its neighboring salt, potentially affecting the repository integrity. Thus, studying the thermal behavior of polyhalite is important. In this paper, a polyhalite sample containing a small amount of halite was collected from the Salado formation at the WIPP site in Carlsbad, New Mexico. To determine its thermal behavior, in situ high-temperature synchrotron X-ray diffraction was conducted from room temperature to 1066 K with the sample powders sealed in a silica-glass capillary. At about 506 K, polyhalite started to decompose into water vapor, anhydrite (CaSO 4 ) and two langbeinite-type phases, K 2 Ca x Mg 2-x (SO 4 ) 3 , with different Ca/Mg ratios. XRD peaks of the minor halite disappeared, presumably due to its dissolution by water vapor. With further increasing temperature, the two langbeinite solid solution phases displayed complex variations in crystallinity, composition and their molar ratio and then were combined into the single-phase triple salt, K 2 CaMg(SO 4 ) 3 , at ~919 K. Rietveld analyses of the XRD data allowed determination of structural parameters of polyhalite and its decomposed anhydrite and langbeinite phases as a function of temperature. Finally, from the results, the thermal expansion coefficients of these phases have been derived, and the structural mechanisms of their thermal behavior been discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗