SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An electrochemical device includes a lithium anode having a red poly(benzonitrile) coating covering at least a portion of the anode; a separator and an air cathode comprising reduced graphene oxide over gas diffusion layer; and an electrolyte comprising an ether solvent, benzonitrile, and a lithium salt.
Abstract An atomically dispersed reduced graphene aerogel (rGA)‐supported iridium catalyst having reactive ethylene ligands was synthesized at an iridium loading of 9.9 wt % and coated with an ionic liquid, 1‐ethyl‐3‐methylimidazolium acetate ([EMIM][OAc]). Continuous‐scan X‐ray absorption spectra demonstrated that the iridium remained site‐isolated in flowing equimolar C 2 H 4 and H 2 during a temperature ramp to 100 °C. The data further showed the lack of detectable iridium aggregation when the feed was H 2 ‐rich or even pure H 2 at 100 °C. An Arrhenius plot determined for ethylene hydrogenation catalysis with the sample in flowing equimolar ethylene and hydrogen showed no variation in the apparent activation energy at temperatures up to 100 °C, confirming that the active sites remained intact at the higher temperatures. The results point to opportunities for overcoming the stability limitations of atomically dispersed supported noble metal catalysts by choice of electron‐donor supports and ionic liquid sheaths.
Topics include: Bioreactors Drive Advances in Tissue Engineering; Tooling Techniques Enhance Medical Imaging; Ventilator Technologies Sustain Critically Injured Patients; Protein Innovations Advance Drug Treatments, Skin Care; Mass Analyzers Facilitate Research on Addiction; Frameworks Coordinate Scientific Data Management; Cameras Improve Navigation for Pilots, Drivers; Integrated Design Tools Reduce Risk, Cost; Advisory Systems Save Time, Fuel for Airlines; Modeling Programs Increase Aircraft Design Safety; Fly-by-Wire Systems Enable Safer, More Efficient Flight; Modified Fittings Enhance Industrial Safety; Simulation Tools Model Icing for Aircraft Design; Information Systems Coordinate Emergency Management; Imaging Systems Provide Maps for U.S. Soldiers; High-Pressure Systems Suppress Fires in Seconds; Alloy-Enhanced Fans Maintain Fresh Air in Tunnels; Control Algorithms Charge Batteries Faster; Software Programs Derive Measurements from Photographs; Retrofits Convert Gas Vehicles into Hybrids; NASA Missions Inspire Online Video Games; Monitors Track Vital Signs for Fitness and Safety; Thermal Components Boost Performance of HVAC Systems; World Wind Tools Reveal Environmental Change; Analyzers Measure Greenhouse Gasses, Airborne Pollutants; Remediation Technologies Eliminate Contaminants; Receivers Gather Data for Climate, Weather Prediction; Coating Processes Boost Performance of Solar Cells; Analyzers Provide Water Security in Space and on Earth; Catalyst Substrates Remove Contaminants, Produce Fuel; Rocket Engine Innovations Advance Clean Energy; Technologies Render Views of Earth for Virtual Navigation; Content Platforms Meet Data Storage, Retrieval Needs; Tools Ensure Reliability of Critical Software; Electronic Handbooks Simplify Process Management; Software Innovations Speed Scientific Computing; Controller Chips Preserve Microprocessor Function; Nanotube Production Devices Expand Research Capabilities; Custom Machines Advance Composite Manufacturing; Polyimide Foams Offer Superior Insulation; Beam Steering Devices Reduce Payload Weight; Models Support Energy-Saving Microwave Technologies; Materials Advance Chemical Propulsion Technology; and High-Temperature Coatings Offer Energy Savings.
For this study, we used a combination of experimental spectroscopies, density functional theory calculations, and CO 2 hydrogenation studies to investigate the effects of modifying single-atom Rh 1 /TiO 2 catalysts with functionalized phosphonic acid monolayers. We found that the deposition of specific amine-functionalized ligands resulted in an ~8× increase in site-specific CO 2 reduction turnover frequency at 150 °C and a ~2× increase at 250 °C. On-stream stability also improved following ligand deposition. The effect of the modifier on reactivity was highly sensitive to the proximity of the amine functional group to the surface, which was controlled by adjusting the length of the phosphonic acid tail. Furthermore, deposition of alkyl phosphonic acids without an amine functional group resulted in blocked CO 2 adsorption and a near-complete loss of catalytic activity. Infrared spectroscopy studies suggested that the amine group provided binding sites for CO 2 that enabled hydrogenation when the amine was positioned near a Rh1 site. Phosphonic acid-modified catalysts also exhibited high selectivity to CO over the series product methane; the selectivity effect was traced to modification of the Rh1 sites to favor CO desorption. Phosphonic acid deposition resulted in 80–90% loss of accessible Rh1 sites, likely due to blocking by tail groups. However, even with the loss of sites, under low-temperature reaction conditions, the rates of CO 2 hydrogenation were improved with the coatings, indicating that the remaining sites are highly efficient. Organic functionalization of the supports for atomically dispersed catalysts offers the opportunity to precisely control the positioning of functional groups in the vicinity of a well-defined active site, potentially enabling an additional level of control over active site design.
Hydrogenation reactions are involved in several processes in heterogeneous catalysis. Platinum is the best-known catalyst; however, there are limitations to its practical use. Therefore, it is necessary to explore alternative materials and transition metal carbides (TMCs) have emerged as potential candidates. We explore the possibility of using cheap TMCs as supports for a Pt monolayer, aiming to reduce the amount of the noble metal in the catalyst without a significant loss of its activity towards H 2 dissociation. Hence, analyzing H 2 dissociation from a fundamental point of view is a necessary step towards a further practical catalyst. By means of periodic DFT calculations, we analyze H 2 adsorption and dissociation on Pt/β-Mo 2 C and Pt/α-WC surfaces, as a function of hydrogen surface coverage ( Θ H ), resembling a more realistic model of a catalyst. H 2 dissociation rates were analyzed as a function of the reaction temperature. Overall, the results show that Pt/C-WC and Pt/Mo-Mo 2 C have a Pt-like behavior for H 2 dissociation at Θ H > 1/2 ML. At a particular temperature of 298 K, Pt/C-WC and Pt/Mo-Mo2C have low energy barriers for H 2 * → 2H* (0.13 and 0.11 eV, respectively), close to the value of Pt (0.06 eV). For the highest coverage, i.e. Θ H = 1, Pt/C-WC has a lower activation energy and a higher reaction rate than Pt. Finally, the H 2 dissociation rate is higher in Pt/Mo-Mo 2 C than in Pt when increasing the temperature above 298 K. Our results put Pt/C-WC and Pt/Mo-Mo 2 C under the spotlight as potential catalysts for H 2 dissociation, with a similar performance to Pt, paving the way for further experimental and/or theoretical studies, addressing the capability of Pt/TMC as practical catalysts in hydrogenation reactions.
Herein, we present the preparation of ultrathin gold (Au) films on different M (M = Pd, Pt, Rh, Ir, and Ru) electrodes (Au/M) using magnetron sputtering deposition for oxygen reduction reaction (ORR). The ORR electro-catalytic activities of prepared Au/M catalysts increase as follows: Au/Ru < Au/Ir < Au/Rh < Au/Pt < Au/Pd. Accordingly, the oxygen reduction catalytic behaviors of the Au-modified palladium (Au/Pd) thin films with various Au thicknesses (0.16, 0.24, 0.5, and 1 nm) are investigated in acidic environments. It is found that Au modifications can promote oxygen reduction performances due to the development of more catalytic active sites on the Pd catalyst through the existence of Au atoms. Noticeably, Au/Pd samples exhibit a connection in oxygen reduction ability as a function of Au thickness, with the ultrathin 0.16 nm Au/Pd being the most active ORR catalyst. Significantly, the 0.16 nm Au/Pd material demonstrates superior stability after 1000 potential cycles compared with the 0.16 nm Pt/Pd owing to the influence of Au coating and structurally stable surfaces. Therefore, surface modification with the deposition of Au films on Pd represents a favorable technique to boost both the ORR capability and stability of the electro-catalysts.
Polymer electrolyte membrane fuel cells (PEMFC) show substantial promise for their application in electric vehicles. For large-scale manufacturing of PEMFCs, roll-to-roll coated gas-diffusion-electrodes (GDE) offer certain advantages over other production pathways. Procedures including hot pressing and coating an ionomer overlayer may be necessary for this manufacturing pathway to enable a suitable catalyst layer/membrane interface. The same procedures may potentially introduce membrane irregularities, especially when thin membranes are used. Limited understanding exists regarding if and to what extent such irregularities impact PEMFC performance and lifetime, and therefore be considered defects. In this study, NREL's customized fuel cell hardware that enables quasi in-situ infrared (IR) thermography studies was utilized to visualize spatial hydrogen crossover and identify membrane irregularities that originated from the GDE-based MEA fabrication process. The structure of these membrane irregularities was investigated by scanning electron microscopy (SEM) and its impact on initial H2/air performance was determined. Accelerated stress testing (AST) revealed that these irregularities develop into failure point locations. These results were validated across many MEAs with identified process-induced membrane irregularities. By selecting specific gas diffusion media properties and by fine tuning the MEA hot pressing parameters, the formation of such membrane irregularities was mitigated.
Catalytic condensers composed of ion gels separating a metal electrode from a platinum-on-carbon active layer were fabricated and characterized to achieve more powerful, high surface area dynamic heterogeneous catalyst surfaces. Ion gels comprised of poly(vinylidene difluoride)/1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide were spin coated as a 3.8 μm film on a Au surface, after which carbon sputtering of a 1.8 nm carbon film and electron-beam evaporation of 2 nm Pt clusters created an active surface exposed to reactant gases. Electronic characterization indicated that most charge condensed within the Pt nanoclusters upon application of a potential bias, with the condenser device achieving a capacitance of ∼20 μF/cm 2 at applied frequencies of up to 120 Hz. The maximum charge of ∼10 14 |e – | cm –2 was condensed under stable device conditions at 200 °C on catalytic films with ∼10 15 sites cm –2 . Grazing incidence infrared spectroscopy measured carbon monoxide adsorption isobars, indicating a change in the CO* binding energy of ∼19 kJ mol –1 over an applied potential bias of only 1.25 V. Condensers were also fabricated on flexible, large area Kapton substrates allowing stacked or tubular form factors that facilitate high volumetric active site densities, ultimately enabling a fast and powerful catalytic condenser that can be fabricated for programmable catalysis applications.
Solar thermal energy can be effectively collected, transported, stored, and utilized by means of a chemical storage and transport system employing the reversible SO2 oxidation reaction. A solar chemical receiver for SO3 thermal decomposition to SO2 and oxygen was analyzed. Bench tests of a ten foot section of a receiver module were conducted with dissociated sulfuric acid (SO3 and H2O) in an electrical furnace. Measured percent conversion of SO3 was 85% of the equilibrium value. Methods were developed to fabricate and assemble a complete receiver module. These methods included applying an aluminide coating to certain exposed surfaces, assembling concentric tubes with a wire spacer, applying a platinum catalyst to the tubing wall, and coiling the entire assembly into the desired configuration.
A proof-of-concept device is being developed for hydrogen gas production based on water-splitting redox reactions facilitated by cobalt tetra-aryl porphyrins (Co[TArP]) catalysts stacked on carbon nanotubes (CNTs) that are grown on n-doped silicon substrates. The operational principle of the proposed device is based on conversion of photoelectron energy from sunlight into chemical energy, which at a later point, can be turned into electrical and mechanical power. The proposed device will consist of a degenerately n-doped silicon substrate with Si posts covering the surface of a 4-in. (approximately equal to 10cm) wafer. The substrate will absorb radiation, and electrons will move radially out of Si to CNT. Si posts are designed such that the diameters are small enough to allow considerable numbers of electrons to transport across to the CNT layer. CNTs will be grown on top of Si using conformal catalyst (Fe/Ni) deposition over a thin alumina barrier layer. Both metallic and semiconducting CNT will be used in this investigation, thus allowing for additional charge generation from CNT in the IR region. Si post top surfaces will be masked from catalyst deposition so as to prevent CNT growth on the top surface. A typical unit cell will then consist of a Si post covered with CNT, providing enhanced surface area for the catalyst. The device will then be dipped into a solution of Co[TArP] to enable coating of CNT with Co(P). The Si/CNT/Co [TArP] assembly then will provide electrons for water splitting and hydrogen gas production. A potential of 1.23 V is needed to split water, and near ideal band gap is approximately 1.4 eV. The combination of doped Si/CNT/Co [TArP] will enable this redox reaction to be more efficient.
The ability to remove heat is paramount to nuclear fuel performance and longevity. Retaining fission product and separating fuel from reactor coolant and the environment is also necessary to prevent radiological contamination. Conventional nuclear fuel for commercial light water reactors and radioisotope power systems (RPS) is composed of oxide powders pressed into a pellet (cm-scale) and then sealed into a metal cladding to confine the fuel. What typical fuels lack is a method to surround each particle of nuclear fuel in metal, thus providing a more intimate protection layer for accident tolerance and boosting the thermal extraction from the fuel element. In such a way, metal-coated fuel particles increase heat extraction efficiency over clad-pellet designs while increasing the accident tolerance of the fuel. Metal oxide microspheres have wide-ranging applications, including the realm of fuels for nuclear reactors and RPS. Microspheres of uranium oxide/uranium carbide, mixed uranium/plutonium oxides, transuranics, and thorium fuels have been extensively studied. Pacific Northwest National Laboratory has also demonstrated the production of 238 PuO 2 microspheres for RPS applications. Metal-coated oxide microsphere fuels may also be attractive for other applications such as nuclear thermal rockets, future nuclear reactor designs, and catalysts.
Currently, it is unknown what exact process or combination of processes produced organics that are found in meteorites or are detected in comets and nebulas. One particular process that forms organics involves Fischer-Tropsch type (FTT) reactions. Fischer-Tropsch type reactions produce hydrocarbons by hydrogenating carbon monoxide via catalytic reactions. The overall reaction is shown. The products of these reactions have been studied using natural catalysts and calculations of the efficiency of FTT synthesis in the Solar Nebula suggest that these types of reactions could make significant contributions to the composition of material near three AU. We use FTT synthesis to coat amorphous Fesilicate grains with organic material to simulate the chemistry in the early Solar Nebula. We used lab-synthesized amorphous Fe-silicate grains for the catalyst because they might better simulate the starting materials found in protostellar nebulas. A brief description of the synthesis of these grains is given in Experiments. This work is different from previous studies because we focus here on the carbonaceous material deposited on the grains. In our experiments, we roughly simulate a model of the nebular environment where grains are successively transported from hot to cold regions of the nebula. In other words, the starting cold regions of the nebula. In other words, the starting gases and FTT products are continuously circulated through the grains at high temperature with intervals of cooling. Overall, organics generated in this manner could represent the carbonaceous material incorporated into comets and meteorites. We present the analyses of the organics produced using pyrolysis gas chromatography mass spectrometry (GCMS) and compare the results with those organics found in the Murchison meteorite.
A 30-cell, full area short stack containing advanced cell features was tested for 2900 hours. A stack acid addition approach was selected and will be evaluated on the stack at 5000 hours test time. A brassboard inverter was designed and fabrication was initiated. Evaluation of this brassboard inverter will take place in 1984. A Teflon coated commercial heat exchanger was selected as the preferred approach for the acid condenser. A reformer catalyst with significantly less pressure drop and equivalent performance relative to the 40-K baseline catalyst was selected for the development reformer. The early 40-kW field power plant history was reviewed and adjustments were made to the On-Site Technology Development Program to address critical component issues.
The electrocatalytic reduction of CO 2 (CO 2 R) into hydrocarbon fuels, such as ethylene and ethanol, provides an attractive pathway towards closing the industrial carbon cycle and producing chemicals using renewable electricity. Existing CO 2 R technologies can exhibit C 2+ product selectivity above 74% and operating current densities over 1.3 A/cm 2 , but none can achieve both simultaneously, limiting the commercial viability and scalability of this technology. Low CO 2 concentrations at the catalyst surface and competing side reactions such as the hydrogen evolution reaction (HER) inhibit C 2+ faradaic efficiencies and operational current densities. Additionally, the use of high surface area cathode geometries to increase operational current densities is under-investigated. In this work, we electrodeposit a macroporous copper dendrite film to form high surface area cathodes. These structures are then coated with a combination of hydrophobic/hydrophilic ionomers to achieve high electrochemically active surface areas (ECSA), form regions of intrinsic porosity, and maximize catalytic availability of CO 2 . Using these techniques, we hope to maximize C 2+ faradaic efficiencies (FE) and geometric partial current densities. The treated cathode compound macrostructure (~10μm-sized pores, and ~μm-long dendrites) and concomitant surface area allows increased geometric current densities while the ionomer coating simultaneously inhibits HER and increases hydrogen availability to improve C 2+ selectivity. Our results show that careful engineering of the catalyst-electrolyte interface can enhance CO 2 reduction product selectivity and efficiency.
Cu-ZnO-Al 2 O 3 is the most widely applied catalyst for CO 2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalysts have been successfully demonstrated. Here, by using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al 2 O 3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h –1 kg –1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO 2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO 2 dissociation.
A method for applying a mixed metal oxide catalyst to a metallic substrate for the creation of a robust, high temperature catalyst system for use in decomposing propellants, particularly hydrogen peroxide propellants, for use in propulsion systems. The method begins by forming a prepared substrate material consisting of a metallic inner substrate and a bound layer of a noble metal intermediate. Alternatively, a bound ceramic coating, or frit, may be introduced between the metallic inner substrate and noble metal intermediate when the metallic substrate is oxidation resistant. A high-activity catalyst slurry is applied to the surface of the prepared substrate and dried to remove the organic solvent. The catalyst layer is then heat treated to bind the catalyst layer to the surface. The bound catalyst layer is then activated using an activation treatment and calcinations to form the high-activity catalyst system.
Fuel cell heavy-duty vehicles (HDVs) require increased durability of oxygen-reduction-reaction electrocatalysts, making knowledge of realistic degradation mechanisms critical. Here identical-location micro-X-ray fluorescence spectroscopy was performed on membrane electrode assemblies. The results exposed heavy in-plane movement of electrocatalyst after HDV lifetime, suggesting that electrochemical Ostwald ripening may not be a local effect. Development of local loading hotspots and preferential movement of electrocatalyst away from cathode catalyst layer cracks was observed. The heterogeneous degradation exhibited by a modified cathode gas diffusion layer membrane electrode assembly after HDV lifetime was successfully quantified by the identical-location approach. Further synchrotron micro-X-ray diffraction and micro-X-ray fluorescence experiments were performed to obtain the currently unknown correlation between electrocatalyst nanoparticle size increase and loading change. A direct correlation was discovered which developed only after HDV lifetime. Finally, the work provides a route to engineer immediate system-level mitigation strategies and to develop structured cathode catalyst layers with durable electrocatalysts.
Widespread implementation of dielectric barrier discharge (DBD)-assisted NH 3 synthesis, a nascent technology operating under sustainable, ambient conditions, is hindered by low energy yields due to, in part, poor fundamental understanding. Porous oxides used to support metal nanoparticle catalysts have shown significant energy yield contributions for DBD-assisted NH 3 synthesis even without metal. Using an AC-powered, coaxial, single-stage reactor at 16 kV with equimolar (N 2 /H 2 ) feed, we measured NH 3 synthesis rates in the presence of different nonordered oxides, ordered SiO 2 structures (SBA-15 and MCM-41), and ordered Al-incorporated analogues (γ-Al 2 O 3 -coated with varying Al-loadings and Al-substitution, respectively: Al 2 O 3 -SBA-15 and Al-MCM-41). We systematically quantified NH 3 energy yield dependence on pore structures and material identities (i.e., ordered pores and Al incorporation) known to facilitate higher DBD-assisted NH 3 synthesis rates. SBA-15 displayed a higher steady-state energy yield than MCM-41, indicating that framework type is a crucial factor, with both ordered porous systems outperforming fumed SiO 2 . 10 wt % Al maximized in situ NH 3 uptake among the various Al loadings, exhibiting a higher steady-state energy yield and similar power to SBA-15. However, Al-MCM-41 had a similar steady-state energy yield and lower power than MCM-41, likely due to the extended γ-Al 2 O 3 surface that has a dielectric constant higher than that of SiO 2 . Both Al-incorporated analogues benefit from surface acid sites that can adsorb NH 3 in situ, resulting in higher overall NH 3 energy yields than that of their parent ordered SiO 2 . Al 2 O 3 -SBA-15 shielded more NH 3 than Al-MCM-41, likely due to a higher acid site density than the acid site identity. Furthermore, Al incorporation via γ-Al 2 O 3 coating more successfully improves the NH 3 energy yield; together with the high-performing ordered framework, these analogues are potential metal catalyst supports with promising energy yields for DBD-assisted synthesis of NH 3 and other chemicals.