SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This paper discusses the electrical properties of the complementary heterojunction field-effect transistor (CHFET) at 4K, including the gate leakage current, the subthreshold transconductance, and the input-referred noise voltage.
We have demonstrated a bound to continuum state GaAs/AlxGa1-xAs infrared hot electron transistor which has a peak response at (sub =16.3). This device utilizes a bound-to-continuum quantum well infrared photodetector as a photosensitive emitter and a wide AlxGa1-xAs barrier between the base and the collector as an energy discriminating filter.
We demonstrate Indium Phosphide Double Heterojunction Bipolar Transistors with simultaneous cutoff frequency Fmax of 288 GHz and current gain cutoff frequency Ft of 251 GHz.
Organic strain gauge and other sensors require high-gain, precision dc amplification to process their low-level output signals. Ideally, amplifiers would be fabricated using organic thin-film field-effect transistors (OTFT's) adjacent to the sensors. However, OTFT amplifiers exhibit low gain and high input-referred dc offsets that must be effectively managed. This paper presents a four-stage, cascaded differential OTFT amplifier utilizing switched capacitor auto-zeroing. Each stage provides a nominal voltage gain of four through a differential pair driving low-impedance active loads, which provide common-mode output voltage control. p-type pentacence OTFT's are used for the amplifier devices and auto-zero switches. Simulations indicate the amplifier provides a nominal voltage gain of 280 V/V and effectively amplifies a 1-mV dc signal in the presence of 500-mV amplifier input-referred dc offset voltages. Future work could include the addition of digital gain calibration and offset correction of residual offsets associated with charge injection imbalance in the differential circuits.
The power systems for use in NASA space missions must work reliably under harsh conditions including radiation, thermal cycling, and exposure to extreme temperatures. Gallium nitride semiconductors show great promise, but information pertaining to their performance is scarce. Gallium nitride N-channel enhancement-mode field effect transistors made by EPC Corporation in a 2nd generation of manufacturing were exposed to radiation followed by long-term thermal cycling and testing under high temperature reverse bias conditions in order to address their reliability for use in space missions. Result of the experimental work are presented and discussed.
The purpose of this test was to characterize the Philips/NXP BFR92A NPN 5 gigahertz wide band silicon transistor for total dose response. This test shall serves as the radiation lot acceptance test (RLAT) for the lot date code (LDC) 1027. The BFR92A is packaged in a 3-pin plastic SOT23 package. Low dose rate (LDR/ELDRS) irradiations was performed.
The purpose of this testing was to characterize the InterFET Corporation U309 for total dose response. This test shall serve as the radiation lot acceptance test (RLAT) for the lot date code (LDC) tested. The U309 is a discrete Junction Field Effect Transistor (JFET). High dose rate (HDR) irradiations were performed in this test so that the device susceptibility to Total Ionizing Dose (TID) could be determined.
Semiconducting polymers offer synthetic tunability, good mechanical properties, and biocompatibility, enabling the development of soft technologies previously inaccessible. Side-chain engineering is a versatile approach for optimizing these semiconducting materials, but minor modifications can significantly impact material properties and device performance. Carbohydrate side chains have been previously introduced to improve the solubility of semiconducting polymers in greener solvents. Despite this achievement, these materials exhibit suboptimal performance and stability in field-effect transistors. In this work, structure–property relationships are explored to enhance the device performance of carbohydrate-bearing semiconducting polymers. Toward this objective, a series of isoindigo-based polymers with carbohydrate side chains of varied carbon-spacer lengths is developed. Material and device characterizations reveal the effects of side chain composition on solid-state packing and device performance. With this new design, charge mobility is improved by up to three orders of magnitude compared to the previous studies. Processing–property relationships are also established by modulating annealing conditions and evaluating device stability upon air exposure. Notably, incidental oxygen-doping effects lead to increased charge mobility after 10 days of exposure to ambient air, correlated with decreased contact resistance. Bias stress stability is also evaluated. This work highlights the importance of understanding structure–property relationships toward the optimization of device performance
Abstract The fundamental challenge in electron‐transporting organic mixed ionic‐electronic conductors (OMIECs) is simultaneous optimization of electron and ion transport. Beginning from Y6‐type/U‐shaped non‐fullerene solar cell acceptors, we systematically synthesize and characterize molecular structures that address the aforementioned challenge, progressively introducing increasing numbers of oligoethyleneglycol (OEG; g) sidechains from 1 g to 3 g, affording OMIECs 1gY, 2gY, and 3gY, respectively. The crystal structure of 1gY preserves key structural features of the Y n series: a U‐shaped/planar core, close π–π molecular stacking, and interlocked acceptor groups. Versus inactive Y6 and Y11, all of the new glycolated compounds exhibit mixed ion‐electron transport in both conventional organic electrochemical transistor (cOECT) and vertical OECT (vOECT) architectures. Notably, 3gY with the highest OEG density achieves a high transconductance of 16.5 mS, an on/off current ratio of ~10 6 , and a turn‐on/off response time of 94.7/5.7 ms in vOECTs. Systematic optoelectronic, electrochemical, architectural, and crystallographic analysis explains the superior 3gY‐based OECT performance in terms of denser n gY OEG content, increased crystallite dimensions with decreased long‐range crystalline order, and enhanced film hydrophilicity which facilitates ion transport and efficient redox processes. Finally, we demonstrate an efficient small‐molecule‐based complementary inverter using 3gY vOECTs, showcasing the bioelectronic applicability of these new small‐molecule OMIECs.
Abstract The fundamental challenge in electron‐transporting organic mixed ionic‐electronic conductors (OMIECs) is simultaneous optimization of electron and ion transport. Beginning from Y6‐type/U‐shaped non‐fullerene solar cell acceptors, we systematically synthesize and characterize molecular structures that address the aforementioned challenge, progressively introducing increasing numbers of oligoethyleneglycol (OEG; g) sidechains from 1 g to 3 g, affording OMIECs 1gY, 2gY, and 3gY, respectively. The crystal structure of 1gY preserves key structural features of the Y n series: a U‐shaped/planar core, close π–π molecular stacking, and interlocked acceptor groups. Versus inactive Y6 and Y11, all of the new glycolated compounds exhibit mixed ion‐electron transport in both conventional organic electrochemical transistor (cOECT) and vertical OECT (vOECT) architectures. Notably, 3gY with the highest OEG density achieves a high transconductance of 16.5 mS, an on/off current ratio of ~10 6 , and a turn‐on/off response time of 94.7/5.7 ms in vOECTs. Systematic optoelectronic, electrochemical, architectural, and crystallographic analysis explains the superior 3gY‐based OECT performance in terms of denser n gY OEG content, increased crystallite dimensions with decreased long‐range crystalline order, and enhanced film hydrophilicity which facilitates ion transport and efficient redox processes. Finally, we demonstrate an efficient small‐molecule‐based complementary inverter using 3gY vOECTs, showcasing the bioelectronic applicability of these new small‐molecule OMIECs.
In this study, we introduce two thiophene-phenylene-thiophene (TPT) polymers designed to leverage noncovalent intramolecular interactions to regulate main-chain conformation and enhance solid-state ordering. By incorporating unsubstituted thiophene (T) or bithiophene (2T) units, we reveal striking divergence in the thermal, morphological, and optoelectronic properties of the resulting films, facilitated by these noncovalent interactions. Using a combination of computational and experimental approaches, we show that annealing yields remarkably different polymer conformations and, consequently, charge transport properties. TPT-T undergoes a significant structural transformation, adopting a more planar backbone conformation and a highly crystalline, edge-on molecular orientation. In contrast, the introduction of a single additional thiophene unit in TPT-2T leads to a more isotropic molecular orientation with a slight preference for face-on alignment, resulting in a heterogeneous film structure that hinders charge transport despite achieving tighter molecular packing. Remarkably, despite being composed of achiral components, TPT-2T develops chirality upon annealing, indicating the formation of a helical conformation. Organic field-effect transistor measurements reveal that the well-ordered alignment in annealed TPT-T films results in higher charge carrier mobility and a narrower distribution of mobility values than in TPT-2T. These findings provide critical insights into the structure−property relationships of conjugated polymers, offering guidance for optimizing molecular design and processing strategies for highperformance organic electronic materials.
Two-dimensional (2D) semiconductors with narrow bandgaps are promising candidates for near- and far-infrared (IR) photodetection, particularly in the telecommunication spectral window. However, current low-bandgap IR photodetectors face significant challenges due to their high dark current, increased carrier recombination, and thermally generated noise. Here, in this work, a hybrid phototransistor is demonstrated by integrating direct, contact-free palladium diselenide (PdSe 2 ) as a highly responsive IR detection layer with a non-IR-absorbing molybdenum diselenide (MoSe 2 ) field-effect transistor (FET), using a near-IR source at a wavelength of λ = 1650 nm. Exfoliated PdSe 2 flakes integrated into a back-gated FET architecture exhibit ambipolar transport behavior, with extracted hole and electron mobilities of 24.8 cm 2 V –1 s –1 and 58.4 cm 2 V –1 s –1 , respectively. The devices show a clear photocurrent generation under the illumination of a λ = 1650 nm laser source, achieving a notable responsivity of ∼300 mA W -1 at an applied gate voltage of 15 V, which highlights the suitability of PdSe 2 as a narrow-bandgap material for photodetection. Photoresponsivity saturates and does not have any effect above an applied gate voltage of 15 V. To further tune the photoresponsivity performance continuously with the applied gate voltage, we construct a van der Waals heterostructure phototransistor, where few layers of PdSe 2 are directly transferred onto the 2D channel region of a MoSe 2 FET, while avoiding any contact with the metal electrodes. In this heterostructure, PdSe 2 works as the primary active IR-absorbing layer, while MoSe 2 provides high-performance FET characteristics. This spatial separation of absorption and transport facilitates efficient interlayer charge transfer and charge separation, resulting in high responsivities of up to 972 mA W –1 at near-IR wavelengths and a low power density of 1.5 mW/mm 2 . The responsivity of our photodetector is comparable to that of some state-of-the-art commercially available NIR photodetectors, highlighting the potential of PdSe 2 -based heterostructures as scalable, CMOS-compatible platforms for high-performance near-IR detection.
How do chemical and structural modifications to the supporting crystal surface affect the subsequent van der Waals (vdW) or quasi(Q)-vdW epitaxial growth of 2D nanocrystals? Developing an atomic-scale picture of such an interfacial system is crucial for understanding its impact on the physical and chemical properties of the supported 2D materials. The elucidation of the interfacial structure and chemistry needed to promote the Q-vdW epitaxial growth of 2D tungsten disulfide (WS 2 ) nanocrystals contributes to the growth mechanism understanding, thus pushing forward the integration of such atomically thin semiconductors toward real field-effect transistor applications. In addition to an atomic-force microscopy top view, we showcase a combination of X-ray techniques for a top-to-bottom investigation of the complexities of the buried interface structures. Furthermore, this approach uses X-ray photoelectron spectroscopy, X-ray standing wave excited X-ray fluorescence, and crystal truncation rod scattering to produce a highly resolved chemical-state-specific 3D atomic map for the extended interface structure of WS 2 /α-Al 2 O 3 (001). Employing these detailed analysis methods, along with density functional theory to further refine the picoscale structure, we demonstrate how two different types of interface engineering during the pregrowth stage lead to significant differences in the chemical and structural modifications to the terminal surface of c-face sapphire, which in turn leads to substantial differences in the submonolayer growth of supported WS 2 2D nanocrystals in terms of lateral domain sizes, epitaxial registry, vdW gaps, and stability.
Electrolyte-gated transistors with ion-trapping layers offer a promising platform for artificial synapses in neuromorphic computing, yet molecular mechanisms governing ionic retention remain poorly understood. Here, in this study, we present a supramolecular approach to modulate ion retention by incorporating a crown ether derivative-based polymer network as an ion-trapping layer on top of a semiconducting monolayer. We show that the balance between ion–host binding and ion–solvent interactions dictates the kinetics of ion capture and release, which in turn controls the memory characteristics of the device. By varying the solvent dielectric constant, we tune the ionic retention time from nearly permanent trapping to rapid relaxation. Intermediate solvent polarity enables programmable short- and long-term synaptic behaviors, including excitatory postsynaptic current, paired-pulse facilitation, and long-term potentiation and depression. These findings establish a direct link between supramolecular ion recognition and synaptic plasticity and provide a generalizable design strategy for ionic–electronic neuromorphic devices.
Single-crystal hexagonal boron nitride (hBN) is used extensively in many two-dimensional electronic and quantum devices, where defects significantly impact performance. Therefore, characterizing and engineering hBN defects are crucial for advancing these technologies. Here, we examine the capture and emission dynamics of defects in hBN by utilizing low-frequency noise (LFN) spectroscopy in hBN-encapsulated and graphene-contacted MoS 2 field-effect transistors (FETs). The low disorder of this heterostructure allows the detection of random telegraph signals (RTS) in large device dimensions of 100 μm 2 at cryogenic temperatures. Analysis of gate bias- and temperature-dependent LFN data indicate that RTS originates from a single trap species within hBN. By performing multi-space density functional theory (MS-DFT) calculations on a gated defective hBN/MoS 2 heterostructure model, we assign substitutional carbon atoms in boron sites as the atomistic origin of RTS. This study demonstrates the utility of LFN spectroscopy combined with MS-DFT analysis on a low-disorder all-vdW FET as a powerful means for characterizing the atomistic defects in single-crystal hBN.
Abstract This study discusses the feasibility of Ferroelectric Capacitors (FeCaps) and Ferroelectric Field-Effect Transistors (FeFETs) as In-Memory Computing (IMC) elements to accelerate machine learning (ML) workloads. We conducted an exploration of device fabrication and proposed system-algorithm co-design to boost performance. A novel FeCap device, incorporating an interfacial layer (IL) and$$\text {Hf}_{0.5}\text {Zr}_{0.5}\text {O}_2$$ Hf 0.5 Zr 0.5 O 2 (HZO), ensures a reduction in operating voltage and enhances HZO scaling while being compatible with CMOS circuits. The IL also enriches ferroelectricity and retention properties. When integrated into crossbar arrays, FeCaps and FeFETs demonstrate their effectiveness as IMC components, eliminating sneak paths and enabling selector-less operation, leading to notable improvements in energy efficiency and area utilization. However, it is worth noting that limited capacitance ratios in FeCaps introduced errors in multiply-and-accumulate (MAC) computations. The proposed co-design approach helps in mitigating these errors and achieves high accuracy in classifying the CIFAR-10 dataset, elevating it from a baseline of 10% to 81.7%. FeFETs in crossbars, with a higher on-off ratio, outperform FeCaps, and our proposed charge-based sensing scheme achieved at least an order of magnitude reduction in power consumption, compared to prevalent current-based methods.
Improving the sensitive and selective detection of analytes in a variety of applications requires accelerating the rational design of field-effect transistor (FET) chemical sensors. Achieving high-performance detection relies on identifying optimal probe materials that can effectively interact with target analytes, a process traditionally driven by chemical intuition and time-consuming trial-and-error methods. To address the difficulties in probe screening for FET sensor development, this work presents a methodology that combines neuromorphic machine learning (ML) architectures, specifically a hybrid spiking graph neural network (SGNN), with an enriched dataset of physicochemical properties through semi-automated data extraction using large language models. Achieving a classification accuracy of 0.89 in predicting sensor sensitivity categories, the SGNN model outperformed traditional ML techniques by leveraging its ability to capture both global physicochemical properties and sparse topological features through a hybrid modeling framework. Next-generation sensor design was informed by the actionable insights into the connections between material properties and sensing performance offered by the SGNN framework. Through virtual screening for the detection of per- and polyfluoroalkyl substances (PFAS) as a use case, the effectiveness of the SGNN model was further validated. Density functional theory simulations confirmed graphene as a promising active material for PFAS detection as suggested by the SGNN framework. By bridging gaps in predictive modeling and data availability, this integrated approach provides a strong foundation for accelerating advancements in FET sensor design and innovation.
The metal-to-insulator phase transition (MIT) in two-dimensional (2D) materials under the influence of a gating electric field has revealed interesting electronic behavior and the need for a deeper fundamental understanding of electron transport processes, while attracting much interest in the development of next-generation electronic and optoelectronic devices. Although the mechanism of the MIT in 2D semiconductors is a topic under debate in condensed matter physics, our work demonstrates the tunable percolative phase transition in few-layered MoSe 2 field-effect transistors (FETs) using different metallic contact materials. Here, we attempted to understand the MIT through temperature-dependent electronic transport measurements by tuning the carrier density in a MoSe 2 channel under the influence of an applied gate voltage. In particular, we have examined this phenomenon using the conventional chromium (Cr) and ferromagnetic cobalt (Co) as two metal contacts. For both Cr and Co, our devices demonstrated n-type behavior with a room-temperature field-effect mobility of 16 cm 2 V −1 s −1 for the device with Cr-contacts and 92 cm 2 V −1 s −1 for the device with Co-contacts, respectively. Further, with low temperature measurements at 50 K, the mobilities increased significantly to 65 cm 2 V −1 s −1 for the device with Cr and 394 cm 2 V −1 s −1 for the device with Co-contacts. By fitting our experimental data to the percolative phase transition theory, the temperature-dependent conductivity data show a transition from an insulating-to-metallic behavior at a bias of ∼28 V for Cr-contacts and ∼20 V for Co-contacts. This cross-over of the conductivity can be attributed to an increase in carrier density as a function of the gate bias in temperature-dependent transfer characteristics. By extracting the critical exponents, we find that the transport behavior in the device with Co-contacts aligns closely with the 2D percolation theory. In contrast, the devices with Cr-contacts deviate significantly from the 2D limit at low temperatures.