Search NASA⌕ Search

SEARCH · Search NASA

Results for “Commercial Supersonics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Design of Supersonic Transport Flap Systems for Thrust Recovery at Subsonic Speeds

A study of the subsonic aerodynamics of hinged flap systems for supersonic cruise commercial aircraft has been conducted using linear attached-flow theory that has been modified to include an estimate of attainable leading edge thrust and an approximate representation of vortex forces. Comparisons of theoretical predictions with experimental results show that the theory gives a reasonably good and generally conservative estimate of the performance of an efficient flap system and provides a good estimate of the leading and trailing-edge deflection angles necessary for optimum performance. A substantial reduction in the area of the inboard region of the leading edge flap has only a minor effect on the performance and the optimum deflection angles. Changes in the size of the outboard leading-edge flap show that performance is greatest when this flap has a chord equal to approximately 30 percent of the wing chord. A study was also made of the performance of various combinations of individual leading and trailing-edge flaps, and the results show that aerodynamic efficiencies as high as 85 percent of full suction are predicted.

Mann, Michael J.↗

Wake Vortex Wingtip-Turbine Powered Circulation Control High-Lift System

NASA s Vehicle Systems Program is investing in aeronautics technology development across six vehicle sectors, in order to improve future air travel. These vehicle sectors include subsonic commercial transports, supersonic vehicles, Uninhabited Aerial Vehicles (UAVs), Extreme Short Takeoff and Landing (ESTOL) vehicles, Rotorcraft, and Personal Air Vehicles (PAVs). While the subsonic transport is firmly established in U.S. markets, the other vehicle sectors have not developed a sufficient technology or regulatory state to permit widespread, practical use. The PAV sector has legacy products in the General Aviation (GA) market, but currently only accounts for negligible revenue miles, sales, or market share of personal travel. In order for PAV s to ever capture a significant market, these small aircraft require technologies that permit them to be less costly, environmentally acceptable, safer, easier to operate, more efficient, and less dependent on large support infrastructures.

Moore, Mark D.↗

Funding and Strategic Alignment Guidance for Infusing Small Business Innovation Research Technology into NASA Programs Associated with the Aeronautics Research Mission Directorate

This report is intended to help NASA program and project managers incorporate Small Business Innovation Research/Small Business Technology Transfer (SBIR/STTR) technologies that have gone through Phase II of the SBIR program into NASA Aeronautics and Mission Directorate (ARMD) programs. Other Government and commercial program managers can also find this information useful.

safety system↗

Electrified Aircraft Propulsion Development

The benefits of electrified aircraft propulsion improves aircrafts like single aisle transports, enables new configurations of vertical take-off landing aircrafts and revitalizes the economic case for small short-range aircraft services. Future strategies and markets for supersonic and commercial transport are proposed.

Del Rosario, Ruben↗

Recent Enhancements to Modeling Sonic Boom Propagation using Augmented Burgers’ Equation

Sonic boom propagation through the atmosphere is modeled with an augmented Burgers’ equation which includes nonlinearity and loss mechanisms. This work details an updated discretization of the governing equations which is fully conservative and duality preserving. Adjoint equations, for all the mechanisms involved, are re-derived and implemented using adjoint consistent discretizations. Computation of loudness metrics is performed using digital filters. The updated implementation is demonstrated and compared against the previous formulation for selected cases, and the differences are documented and discussed. The improved discretization results in faster mesh convergence of the loudness metrics and substantially de-creases runtime. In addition, the adjoint solutions provide mesh-converged gradients which are free from spurious oscillations.

Sonic Boom↗

Anisotropic Mach Cone Aligned Mesh Adaptation for Low Boom Simulations

An automated off-body Mach cone aligned structured curvilinear grid generation procedure is presented for near-field computational fluid dynamics simulations. This procedure combines output-based indicators and mesh redistribution to perform anisotropic mesh adaptation while maintaining Mach cone alignment. Automation is achieved through a novel direction-based adaptation indicator formulation. The adaptation procedure is demonstrated on the JAXA Wing Body geometry and X-59 C608 demonstrator model from the Second and Third AIAA Sonic Boom Prediction Workshops, respectively. It is demonstrated that anisotropic mesh adaptation may result in a greater than fifty percent reduction in resource usage required to achieve the same level of accuracy as uniform and user constructed Mach cone aligned grids for near-field pressure signatures, ground-level overpressure signatures, and loudness metrics.

CST↗

Anisotropic Mach Cone Aligned Mesh Adaptation for Low Boom Simulations

An automated off-body Mach cone aligned structured curvilinear grid generation procedure is presented for near-field computational fluid dynamics simulations. This procedure combines output-based indicators and mesh redistribution to perform anisotropic mesh adaptation while maintaining Mach cone alignment. Automation is achieved through a novel direction-based adaptation indicator formulation. The adaptation procedure is demonstrated on the JAXA Wing Body geometry and X-59 C608 demonstrator model from the Second and Third AIAA Sonic Boom Prediction Workshops, respectively. It is demonstrated that anisotropic mesh adaptation may result in a greater than fifty percent reduction in resource usage required to achieve the same level of accuracy as uniform and user constructed Mach cone aligned grids for near-field pressure signatures, ground-level overpressure signatures, and loudness metrics.

CST↗

Supersonic Air-Breathing Stage For Commercial Launch Rocket

Concept proposed to expand use of air-breathing, reusable stages to put more payload into orbit at less cost. Stage with supersonic air-breathing engines added to carry expendable stages from subsonic airplane to supersonic velocity. Carry payload to orbit. Expendable stages and payload placed in front of supersonic air-breathing stage. After releasing expendable stages, remotely piloted supersonic air-breathing stage returns to takeoff site and land for reuse. New concept extends use of low-cost reusable hardware and increases payload delivered from B-52.

Martin, James A.↗

Superboom Caustic Analysis and Measurement Program (SCAMP) Final Report

The objectives of the Superboom Caustic Analysis and Measurement (SCAMP) Program were to develop and validate, via flight-test measurements, analytical models for sonic boom signatures in and around focal zones as they are expected to occur during commercial aircraft transition from subsonic to supersonic flight, and to apply these models to focus boom prediction of low-boom aircraft designs. The SCAMP program has successfully investigated sonic boom focusing both analytically and experimentally, while gathering a comprehensive empirical flight test and acoustic dataset, and developing a suite of focused sonic boom prediction tools. An experimental flight and acoustic measurement test was designed during the initial year of the SCAMP program, with execution of the SCAMP flight test occurring in May 2011. The current SCAMP team, led by Wyle, includes partners from the Boeing Company, Pennsylvania State University, Gulfstream Aerospace, Eagle Aeronautics, and Central Washington University. Numerous collaborators have also participated by supporting the experiment with human and equipment resources at their own expense. The experiment involved precision flight of a McDonnell Douglas (now Boeing) F-18B executing different maneuvers that created focused sonic booms. The maneuvers were designed to center on the flight regime expected for commercial supersonic aircraft transonic transition, and also span a range of caustic curvatures in order to provide a variety of conditions for code validations. The SCAMP experiment was designed to capture concurrent F-18B on-board flight instrumentation data, high-fidelity ground-based and airborne acoustic data, and surface and upper air meteorological data. Close coordination with NASA Dryden resulted in the development of new experimental instrumentation and techniques to facilitate the SCAMP flight-test execution, including the development of an F-18B Mach rate cockpit display, TG-14 powered glider in-flight sonic boom measurement instrumentation and "Where's the Focus?" (WTF) software for near-real time way-point computation accounting for local atmospherics. In May 2011, 13 F-18B flights were conducted during 5 flying days over a 2 week period. A densely populated 10,000 ft-long ground acoustic array with 125-ft microphone spacing was designed to capture pre-, focus, and post-focus regions. The ground-based acoustic array was placed in a nominally east-west orientation in the remote Cuddeback lakebed region, north of Edwards AFB. This area was carefully selected to avoid placing focused booms on populated areas or solar power facilities. For the SCAMP measurement campaign, approvals were obtained to temporarily extend the Black Mountain supersonic corridor northward by three miles. The SCAMP flight tests successfully captured 70 boom events, with 61 focus passes, and 9 calibration passes. Seventeen of the focus passes and three of the calibration passes were laterally offset; with the others being centerline flights. Airborne incoming sonic boom wave measurements were measured by the TG-14 for 10 of the F-18B flight passes including one maximum focus signature, several N-u combinations, several overlapped N-u signatures, and several evanescent waves. During the 27-month program, the SCAMP team developed a suite of integrated computer codes with sonic boom focusing predictive capabilities: PCBoom, Lossy Nonlinear Tricomi Equation Method (LNTE) and the Nonlinear Progressive wave Equation (NPE) method. PCBoom propagates the rays through the atmosphere and, in addition to legacy focus signature prediction based on the Gill-Seebass method, provides input source characteristics and propagation parameters to LNTE and NPE. LNTE, a Tricomi solver that incorporates atmospheric losses, computes the focus signature at the focus, and computes the focus signature in the vicinity of the focal zone, including the evanescent and post-focus zones. LNTE signature auralization from low-boom vehicle designs has been demonstrated in the NASA Langley Interior Effects Room (IER). The NPE has also been validated for use in prediction of focused ground boom signatures in sonic boom focal zones. The NPE formulation has the capability to incorporate atmospheric turbulence in the predictions. This has been applied to sonic boom propagation in the past. Prediction of turbulence effects on focal zone signatures was not, however, explored during the SCAMP program.

Page, Juliet↗

Some unique characteristics of supersonic cruise vehicles and their effect on airport community noise

The paper examines the differences between the supersonic and subsonic commercial aircraft in terms of their configuration, aerodynamic characteristics, propulsion systems, and the manner of operation. The unique characteristics of supersonic cruise vehicles should provide improved airport-community noise exposures if the vehicle is permitted to operate at its most efficient and effective flight modes. It is concluded that noise exposure levels for supersonic cruise vehicles can be comparable to those of its equivalent subsonic counterpart of that time period.

Driver, C.↗

Supersonic External-Compression Inlets for Mach 1.4 to 2.0

A series of supersonic, external-compression inlets were designed for freestream Mach numbers of Mach 1.4, 1.7, and 2.0. The types of inlets included axisymmetric pitot, axisymmetric spike, two-dimensional, two-dimensional bifurcated, and streamline-traced inlets. The inlets were designed as isolated from an aircraft with freestream conditions, engine-face geometry, and flow rates established from a reference NASA commercial aircraft concept. The inlets were designed using the NASA Supersonic Inlet Design and Analysis (SUPIN) Tool and the inlet performance was obtained from computational fluid dynamics (CFD) simulations. The study compares the physical dimensions and aerodynamic performance of the inlets to provide reference information for the selection of inlet types for commercial supersonic aircraft.

Supersonics↗

Supersonic External-Compression Inlets for Mach 1.4 to 2.0

A series of supersonic, external-compression inlets were designed for freestream Mach numbers of Mach 1.4, 1.7, and 2.0. The types of inlets included axisymmetric pitot, axisymmetric spike, two-dimensional, two-dimensional bifurcated, and streamline-traced inlets. The inlets were designed as isolated from an aircraft with freestream conditions, engine-face geometry, and flow rates established from a reference NASA commercial aircraft concept. The inlets were designed using the NASA Supersonic Inlet Design and Analysis (SUPIN) Tool and the inlet performance was obtained from computational fluid dynamics (CFD) simulations. The study compares the physical dimensions and aerodynamic performance of the inlets to provide reference information for the selection of inlet types for commercial supersonic aircraft.

Supersonics↗

A History of Jet Noise Research at the National Aeronautics and Space Administration

This paper reviews jet noise research conducted at the National Aeronautics and Space Administration (NASA) from the early 1950s to the present day. Research conducted by NASA’s predecessor, the National Advisory Committee for Aeronautics (NACA), and early years of NASA focused on turbojet noise, where a common approach for reducing jet noise was to limit the jet exit velocity to speeds that provided acceptable noise levels. Suppressors tested during this time resulted in thrust losses that were too severe to be implemented. With the introduction of turbofan engines in the 1960s, NASA shifted research to programs for both subsonic and supersonic aircraft applications with specific noise reduction goals. Subsonic research focused on increasing the bypass ratio of the engine to reduce the jet exit velocity of the core exhaust and adding mixers to the dual exhaust streams. Advances in computational methods improved aerodynamic designs and jet noise prediction tools. Supersonic applications proved to be more troublesome as programs aimed at large commercial transports required higher specific thrust engines. Changing the engine cycle to reduce jet noise was not compatible with mission range and speed requirements. Research for supersonic commercial aircraft remains an area of interest today at NASA.

Jet Noise↗

Aircraft Noise and Performance Data for a Notional Supersonic Business Jet

The International Civil Aviation Organization recently completed a study that determined the global environmental impact of adding several hypothetical supersonic aircraft types to the existing subsonic fleet. NASA supported this study by designing a notional 55-tonne supersonic business jet. The airplane is named the Supersonic Technology Concept Aeroplane by the international community. Performance, noise, and exhaust emission predictions for this transport were used to inform development of new environmental standards for future supersonic civil aircraft. The behavior of the aircraft in an operational setting is considered. Calculation of aircraft noise and performance data for this aircraft is the focus of this paper. Noise abatement departure procedures, stage length performance, and noise-power-distance data are determined using NASA tools. Also investigated are some of the anticipated behaviors and requirements of supersonic aircraft in the commercial airspace.

Aircraft noise↗

Development of Integrated Programs for Aerospace-vehicle design (IPAD): Reference design process

The airplane design process and its interfaces with manufacturing and customer operations are documented to be used as criteria for the development of integrated programs for the analysis, design, and testing of aerospace vehicles. Topics cover: design process management, general purpose support requirements, design networks, and technical program elements. Design activity sequences are given for both supersonic and subsonic commercial transports, naval hydrofoils, and military aircraft.

Meyer, D. D.↗