Nuclear rocket simulator tests, flow initiation with no turbine gas tank pressure, 35 PSIA Run 1
Nuclear reactor simulator test - liquid hydrogen run, instrumentation and data acquisition system operational procedure checkout
LIQUID HYDROGEN↗
SEARCH · Search NASA
Results for “Flow Simulator”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low-Speed Performance Enhancement Using Localized Active Flow Control: Localized Active Flow Control Simulations on a Reference Aircraft (2/4)
A study of the potential implementations of localized active flow control (AFC) technology onto future airplanes is presented. This collaborative investigation addresses key objectives of the NASA Advanced Air Transport Technology (AATT) Project, in terms of reduction in fuel consumption and lower emission. It specifically targets the goals set forth in a roadmap developed by the NASA/Boeing team. The roadmap is a result of a series of meetings held between the two parties over the years and it represents a shared vision for practical implementations, leading up to flight demonstrations of localized flow control. If successful, localized flow control may lead to important ramifications for next generation airplanes from both the economic and environmental perspectives. Under this contract localized AFC has been used to improve aerodynamic performance during high-lift operations using Computational Fluid Dynamics (CFD). Specifically, AFC has been applied at the aileron and at various location in the wing leading edge (LE) regions. The applications target reduced drag and enhanced lift over the range of practical angles of attack, including stall. These benefits translate to airplane performance improvements, such as longer range or larger payload. The CFD results are used to quantify potential aerodynamic benefits, as well as the input required for actuation. This helps identify the most promising candidates, which potentially provide material net airplane level enhancements using onboard fluidic sources. The airplane configuration selected for the CFD study is a representative of a future short/medium-range twin-engine airplane dubbed the Reference Aircraft. A slew of AFC applications has been explored and their aerodynamic performance enhancements were benchmarked against the baseline Reference Aircraft. Promising AFC candidates have been deemed practical and potentially suitable for both the aileron and the wing LE implementations. The findings on the Reference Aircraft are used to guide the development of the AFC-enhanced aileron for the CRM-HL. The wind-tunnel model of the CRM-HL will be used by NASA to validate the AFC concepts, complementing the CFD-based analysis and the integration study (final report document #3).
CFD↗
A Database of CFD-Based Buffet Forcing Functions for Artemis I Structural Response Evaluation
Time-accurate FUN3D simulations are utilized to estimate buffet-induced unsteady forces experienced by the Space Launch System during the Artemis I (AR01) flight. A set of FUN3D simulations was developed that employed time-accurate mesh translations to simulate the changing velocity and attitude based on the AR01 best estimated trajectory. In these simulations, referred to as accelerating-flow simulations, the freestream Mach number increased from 0.80 to 1.92. Additional time-accurate simulations were obtained at constant freestream Mach number equal to 0.95, 1.18, 1.70, thereby simulating stationary conditions experienced by the flow in a wind-tunnel. On the grounds of favorable comparisons between simulated and flight-measured environments, the FUN3D-based surface pressures were utilized to develop a buffet forcing function (BFF) database. This BFF database was analyzed to characterize the spatial distribution and frequency content of the buffet forces during transonic and supersonic portions of the AR01 flight. The region of interest is located downstream of the forward attachment (FA) hardware between the core stage and the solid rocket boosters where vortex shedding off the FA protuberance produces significant unsteadiness. The analysis reveals that, at transonic and supersonic conditions, buffet forces that are based on constant freestream Mach number data are a good approximation of those based on accelerating-flow simulations.
FUN3D↗
A Database of CFD-Based Buffet Forcing Functions for Artemis I Structural Response Evaluation
Time-accurate FUN3D simulations are utilized to estimate buffet-induced unsteady forces experienced by the Space Launch System during the Artemis I (AR01) flight. A set of FUN3D simulations was developed that employed time-accurate mesh translations to simulate the changing velocity and attitude based on the AR01 best estimated trajectory. In these simulations, referred to as accelerating-flow simulations, the freestream Mach number increased from 0.80 to 1.92. Additional time-accurate simulations were obtained at constant freestream Mach number equal to 0.95, 1.18, 1.70, thereby simulating stationary conditions experienced by the flow in a wind-tunnel. On the grounds of favorable comparisons between simulated and flight-measured environments, the FUN3D-based surface pressures were utilized to develop a buffet forcing function (BFF) database. This BFF database was analyzed to characterize the spatial distribution and frequency content of the buffet forces during transonic and supersonic portions of the AR01 flight. The region of interest is located downstream of the forward attachment (FA) hardware between the core stage and the solid rocket boosters where vortex shedding off the FA protuberance produces significant unsteadiness. The analysis reveals that, at transonic and supersonic conditions, buffet forces that are based on constant freestream Mach number data are a good approximation of those based on accelerating-flow simulations.
transonic buffet↗
Viscous Three-Dimensional Simulation of Flow in an Axial Low Pressure Compressor at Engine Icing Operating Points
Viscous three-dimensional simulations of the Honeywell ALF502R-5 low pressure compressor (sometimes called a booster) using the NASA Glenn code GlennHT have been carried out. A total of ten simulations were produced. Five operating points are investigated, with each point run with two different wall thermal conditions. These operating points are at, or near, points where engine icing has been determined to be likely. In the future, the results of this study will be used for further analysis such as predicting collection efficiency of ice particles and ice growth rates at various locations in the compressor. A mixing plane boundary condition is used between each blade row, resulting in convergence to steady state within each blade row. The k-omega turbulence model of Wilcox, combined with viscous grid spacing near the wall on the order of one, is used to resolve the turbulent boundary layers. For each of the operating points, heat transfer coefficients are generated on the blades and walls. The heat transfer coefficients are produced by running the operating point with two different wall thermal conditions and then solving simultaneously for the heat transfer coefficient and adiabatic wall temperature at each point. Average Nusselt numbers are calculated for the most relevant surfaces. The values are seen to scale with Reynolds number to approximately a power of 0.7. Additionally, images of surface distribution of Nusselt number are presented. Qualitative comparison between the five operating points show that there is relatively little change in the character of the distribution. The dominant observed effect is that of an overall scaling, which is expected due to Reynolds number differences. One interesting aspect about the Nusselt number distribution is observed on the casing (outer diameter) downstream of the exit guide vanes (EGVs). The Nusselt number is relatively high between the pairs of EGVs, with two lower troughs downstream of each EGV trailing edge. This is of particular interest since rather complex ice shapes have been observed in that region.
compressor↗
Navier-Stokes and viscous-inviscid interaction
Some considerations toward developing numerical procedures for simulating viscous compressible flows are discussed. Both Navier-Stokes and boundary layer field methods are considered. Because efficient viscous-inviscid interaction methods have been difficult to extend to complex 3-D flow simulations, Navier-Stokes procedures are more frequently being utilized even though they require considerably more work per grid point. It would seem a mistake, however, not to make use of the more efficient approximate methods in those regions in which they are clearly valid. Ideally, a general purpose compressible flow solver that can optionally take advantage of approximate solution methods would suffice, both to improve accuracy and efficiency. Some potentially useful steps toward this goal are described: a generalized 3-D boundary layer formulation and the fortified Navier-Stokes procedure.
Steger, Joseph L.↗
Uncertainty Assessments of 2D and Axisymmetric Hypersonic Shock Wave - Turbulent Boundary Layer Interaction Simulations at Compression Corners
This paper is one of a series of five papers in a special session organized by the NASA Fundamental Aeronautics Program that addresses uncertainty assessments for CFD simulations in hypersonic flow. Simulations of a shock emanating from a compression corner and interacting with a fully developed turbulent boundary layer are evaluated herein. Mission relevant conditions at Mach 7 and Mach 14 are defined for a pre-compression ramp of a scramjet powered vehicle. Three compression angles are defined, the smallest to avoid separation losses and the largest to force a separated flow engaging more complicated flow physics. The Baldwin-Lomax and the Cebeci-Smith algebraic models, the one-equation Spalart-Allmaras model with the Catrix-Aupoix compressibility modification and two-equation models including Menter SST, Wilcox k-omega 98, and Wilcox k-omega 06 turbulence models are evaluated. Each model is fully defined herein to preclude any ambiguity regarding model implementation. Comparisons are made to existing experimental data and Van Driest theory to provide preliminary assessment of model form uncertainty. A set of coarse grained uncertainty metrics are defined to capture essential differences among turbulence models. Except for the inability of algebraic models to converge for some separated flows there is no clearly superior model as judged by these metrics. A preliminary metric for the numerical component of uncertainty in shock-turbulent-boundary-layer interactions at compression corners sufficiently steep to cause separation is defined as 55%. This value is a median of differences with experimental data averaged for peak pressure and heating and for extent of separation captured in new, grid-converged solutions presented here. This value is consistent with existing results in a literature review of hypersonic shock-turbulent-boundary-layer interactions by Roy and Blottner and with more recent computations of MacLean.
Gnoffo, Peter A.↗
Virtual and Experimental Visualization of Flows in Packed Beds of Spheres Simulating Porous Media Flows
A videotape presentation of flow in a packed bed of spheres is provided. The flow experiment consisted of three principal elements: (1) an oil tunnel 76.2 mm by 76.2 mm in cross section, (2) a packed bed of spheres in regular and irregular arrays, and (3) a flow characterization methodology, either (a) full flow field tracking (FFFT) or (b) computational fluid dynamic (CFD) simulation. The refraction indices of the oil and the test array of spheres were closely matched, and the flow was seeded with aluminum oxide particles. Planar laser light provided a two-dimensional projection of the flow field, and a traverse simulated a three-dimensional image of the entire flow field. Light focusing and reflection rendered the spheres black, permitting visualization of the planar circular interfaces in both the axial and transverse directions. Flows were observed near the wall-sphere interface and within the set of spheres. The CFD model required that a representative section of a packed bed be formed and gridded, enclosing and cutting six spheres so that symmetry conditions could be imposed at all cross-boundaries. Simulations had to be made with the flow direction at right angles to that used in the experiments, however, to take advantage of flow symmetry. Careful attention to detail was required for proper gridding. The flow field was three-dimensional and complex to describe, yet the most prominent finding was flow threads, as computed in the representative 'cube' of spheres with face symmetry and conclusively demonstrated experimentally herein. Random packing and bed voids tended to disrupt the laminar flow, creating vortices.
Hendricks, R. C.↗
Numerical solutions of atmospheric flow over semielliptical simulated hills
Atmospheric motion over obstacles on plane surfaces to compute simulated wind fields over terrain features was studied. Semielliptical, two dimensional geometry and numerical simulation of flow over rectangular geometries is also discussed. The partial differential equations for the vorticity, stream function, turbulence kinetic energy, and turbulence length scale were solved by a finite difference technique. The mechanism of flow separation induced by a semiellipse is the same as flow over a gradually sloping surface for which the flow separation is caused by the interaction between the viscous force, the pressure force, and the turbulence level. For flow over bluff bodies, a downstream recirculation bubble is created which increases the aspect ratio and/or the turbulence level results in flow reattachment close behind the obstacle.
Shieh, C. F.↗
Performance of two transonic airfoil wind tunnels utilizing limited ventilation
A limited-zone ventilated wall panel was developed for a closed-wall icing tunnel which permitted correct simulation of transonic flow over model rotor airfoil sections with and without ice accretions. Candidate porous panels were tested in the Ohio State University 6- x 12-inch transonic airfoil tunnel and result in essentially interference-free flow, as evidenced by pressure distributions over a NACA 0012 airfoil for Mach numbers up to 0.75. Application to the NRC 12- x 12-inch icing tunnel showed a similar result, which allowed proper transonic flow simulation in that tunnel over its full speed range.
Lee, J. D.↗
Flow and heat transfer in space vehicle tile gaps
The flow patterns and the characteristics of the convective heat transfer in intersecting tile gaps on space vehicles were experimentally investigated using a water channel flow facility for simulating flow conditions in the tile gaps on the Aeroassist Flight Experiment (AFE) vehicle. It was found that penetration of external flow into the perpendicular gap was limited in most cases to roughly two gap widths, while greater entrainment occurred in the parallel gap. Heat transfer in the bulk of the perpendicular gap occurred by natural convection. The Reynolds number and the relative tile-height differences had the strongest influence on heat transfer and affected both the magnitude and the symmetry of the temperature and the flow fields.
Garimella, S. V.↗
Driving Parameters for Distributed and Centralized Air Transportation Architectures
This report considers the problem of intersecting aircraft flows under decentralized conflict avoidance rules. Using an Eulerian standpoint (aircraft flow through a fixed control volume), new air traffic control models and scenarios are defined that enable the study of long-term airspace stability problems. Considering a class of two intersecting aircraft flows, it is shown that airspace stability, defined both in terms of safety and performance, is preserved under decentralized conflict resolution algorithms. Performance bounds are derived for the aircraft flow problem under different maneuver models. Besides analytical approaches, numerical examples are presented to test the theoretical results, as well as to generate some insight about the structure of the traffic flow after resolution. Considering more than two intersecting aircraft flows, simulations indicate that flow stability may not be guaranteed under simple conflict avoidance rules. Finally, a comparison is made with centralized strategies to conflict resolution.
Feron, Eric↗
Study of Convective Flow Effects in Endwall Casing Treatments in Transonic Compressor Rotors
The unsteady convective flow effects in a transonic compressor rotor with a circumferential-groove casing treatment are investigated in this paper. Experimental results show that the circumferential-groove casing treatment increases the compressor stall margin by almost 50% for the current transonic compressor rotor. Steady flow simulation of the current casing treatment, however, yields only a 15% gain in stall margin. The flow field at near-stall operation is highly unsteady due to several self-induced flow phenomena. These include shock oscillation, vortex shedding at the trailing edge, and interaction between the passage shock and the tip clearance vortex. The primary focus of the current investigation is to assess the effects of flow unsteadiness and unsteady flow convection on the circumferential-groove casing treatment. Unsteady Reynolds-averaged Navier-Stokes (URANS) and Large Eddy Simulation (LES) techniques were applied in addition to steady Reynolds-averaged Navier-Stokes (RANS) to simulate the flow field at near-stall operation and to determine changes in stall margin. The current investigation reveals that unsteady flow effects are as important as steady flow effects on the performance of the circumferential grooves casing treatment in extending the stall margin of the current transonic compressor rotor. The primary unsteady flow mechanism is unsteady flow injection from the grooves into the main flow near the casing. Flows moving into and out of the grooves are caused due to local pressure difference near the grooves. As the pressure field becomes transient due to self-induced flow oscillation, flow injection from the grooves also becomes unsteady. The unsteady flow simulation shows that this unsteady flow injection from the grooves is substantial and contributes significantly to extending the compressor stall margin. Unsteady flows into and out of the grooves have as large a role as steady flows in the circumferential grooves. While the circumferential-groove casing treatment seems to be a steady flow device, unsteady flow effects should be included to accurately assess its performance as the flow is transient at near-stall operation.
Hah, Chunill↗
Numerical simulation of rarefied flow through a slit. I - Direct simulation Monte Carlo results
The pressure-driven flow of a rarefied monatomic gas through a two-dimensional slit is simulated using the direct simulation Monte Carlo technique. Of particular interest is the change in flow field structure as pressure ratio and Knudsen number are varied. Comparisons are made to quantify the limits of validity of free-molecular theory and approximate, nearly free-molecular iterative methods. Also addressed is the sensitivity of the numerical solutions to grid structure and boundary conditions. The free-molecular theory is found to predict quantitative flow field properties (e.g., centerline velocities or downstream flux profiles) reasonably well for large finite Knudsen number with the error dependent on the pressure ratio. The nearly free-molecular corrections are shown to have limited range of applicability. A previously derived parameter is found to correlate total mass flux well as a function of pressure ratio and Knudsen number over a large portion of the transitional regime.
Wadsworth, D. C.↗
Optimal Inlet Shape Design of N2B Hybrid Wing Body Configuration
The N2B hybrid wing body aircraft was conceptually designed to meet environmental and performance goals for the N+2 generation transport set by the Subsonic Fixed Wing project of NASA Fundamental Aeronautics Program. In the present study, flow simulations are conducted around the N2B configuration by a Reynolds-averaged Navier-Stokes flow solver using unstructured meshes. Boundary conditions at engine fan face and nozzle exhaust planes are provided by the NPSS thermodynamic engine cycle model. The flow simulations reveal challenging design issues arising from boundary layer ingestion offset inlet and airframe-propulsion integration. Adjoint-based optimal designs are then conducted for the inlet shape to minimize the airframe drag force and flow distortion at fan faces. Design surfaces are parameterized by NURBS, and the cowl lip geometry is modified by a spring analogy approach. By the drag minimization design, flow separation on the cowl surfaces are almost removed, and shock wave strength got remarkably reduced. For the distortion minimization design, a circumferential distortion indicator DPCP(sub avg) is adopted as the design objective and diffuser bottom and side wall surfaces are perturbed for the design. The distortion minimization results in a 12.5 % reduction in the objective function.
Kim, Hyoungjin↗
Advancements in turbulence modeling
Direct simulation data are used to test newly proposed nonlinear models in the Reynolds stress anisotropy for the rapid pressure-strain terms. It is found that the nonlinear models will perform better than the linear models. In addition to testing the rapid pressure-strain models, a new k-epsilon model is proposed for near-wall flow simulation. The model is proposed for near-wall flow simulation. The model was developed by fitting low-Reynolds number data from a direct simulation of a channel flow. A new wall-correction for the eddy-viscosity as well as wall-corrections for the epsilon-equation are proposed. The model will give better predictions of the turbulent kinetic profile in the near-wall region than existing models.
Mansour, N. N.↗
Glenn Heat Transfer Simulation and Solver Graphical User Interface: Development and Testing
In the Tui ine Branch of the Turbomachinery and Propulsion Systems Division, researching and developing efficient turbine aerothermodynamics technologies is the main objective. Creating effective turbines for jet engines is a process which, if based purely on physical experimental testing, would be extremely expensive. It is for this reason, and also for the reasons of speed and ease, that the Turbine Branch spends a large amount of effort working with simulations of turbines. Specifically, they focus their work on two main fields: Computational Field Dynamics (CFD), and Experimental data analysis. The experimental field involves comparing experimental results to simulated results, whereas the CFD field involves running these simulations. The simulations are applied to aerodynamics and heat transfer cases, for both steady and unsteady flow conditions. By and large this work is applied to the domain of flow and heat transfer in axial turbines. The main application used to run these heat flow simulations is GlennHT. This program, recently rewritten in FORTRAN 90, allows the user to input a job file which specifies all the necessary parameters needed to simulate flow through a user-defined grid. There are several other executables used as well, ranging in application from converting grid files to and from particular formats, to merging blocks in a connectivity file, to converting connectivity files to a GlennHT compatible format. All of these executables are run from the command line in a terminal; some of them have interactive prompts where the user must specify the files to be manipulated after the program starts, while others take all of their parameters from the command line. With this amount of variation comes a good deal of commands and formats to memorize, which can cause slower and less efficient work, as users may forget how to execute a certain program, or not remember the pathnames of the files they wish to use. Two years ago, steps were made to expedite this process with a graphical user interface (GUI) that combines the functionality of all the executables along with adding some new functionality, such as residuals graphing and boundary conditions creation. Upon my beginning here at Glenn, many parts of the GUI, which was developed in Java, were nonfunctional. There were also issues with cross-platforming, as systems in the branch were transitioning from Silicon Graphics (SGI) machines to Linux machines. My goals this summer are to finish the parts of the GUI that are not yet completed, fix parts that did not work correctly, expand the functionality to include other useful features, such as grid surface highlighting, and make the system compatible with both Linux and SGI. I will also be heavily testing the system and providing sufficient documentation on how to use the GUI, as no such documentation existed previously.
Kardamis, Joseph R.↗
Wind tunnel measurements in the wake of a simple structure in a simulated atmospheric flow
Measurements of longitudinal mean velocity and turbulence intensity were made in the wake of a rectangular model building in a simulated atmospheric boundary-layer wind. The model building was a 1:50 scale model of a structure used in a wake measurement program at the George C. Marshall Space Flight Center 8-tower boundary-layer facility. The approach wind profile and measurement locations were chosen to match the field site conditions. The wakes of the building in winds from azimuths of 0 and 47 degrees referenced to the normal to the building long axis were examined. The effect of two lines of trees upwind of the building on the wake and the importance of the ratio of the building height to boundary-layer thickness on the extent of the wake were determined.
Hansen, A. C.↗