Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rheological properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Large-scale reactive thermoset printing: Complex interactions between temperature evolution, viscosity, and cure shrinkage

Thermoset composites are strong candidates for large-scale material extrusion additive manufacturing (AM). However, uncured thermoset composites become unstable as print height increases. Here, chemical initiation of vinyl ester immediately before deposition was used to suppress collapse and enable large-scale thermoset printing. Structural stability was assessed by printing thin walls at various layer times and monitoring thermal gradients with an infrared camera. Stable printing was observed at a layer time of 4.50 min, approximately half the gel time of the material (8 min). Self-weight collapse occurred at short layer time (0.68 min), whereas warpage occurred at long layer time (6.50 min). Here, a new behavior was discovered at intermediate layer time (2.25 min) where the heat generated by the reaction causes new, un-gelled layers to flow. Forced convection eliminates this behavior, stabilizing the 2.25-min layer time print. These findings motivated development of a less exothermic material system, which was used to print a large-scale mold and demonstrate the value of this understanding. By presenting these challenges of large-scale reactive thermoset AM for the first time, this work motivates focused studies of the complex interplay between rheological, thermal, and chemical behaviors to improve the feasibility of large-scale thermoset AM. Tensile properties of the printed material were also measured. Longitudinal and transverse elastic moduli are 3.79 and 2.95 GPa, respectively, and corresponding tensile strengths are 36.11 and 18.83 MPa. The glass transition temperature is 93.13 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fluctuations and power-law scaling of dry, frictionless granular rheology near the hard-particle limit

Here the flow of frictionless granular particles is studied with stress-controlled discrete element modeling simulations for systems varying in size from 300 to 100,000 particles. The volume fraction and shear-stress ratio μ are relatively insensitive to system size for a wide range of inertial numbers I. Second-order effects in strain rate, such as normal stress differences, require large system sizes to accurately extract meaningful results, notably a nonmonotonic dependence in the first normal stress difference with strain rate. The rheological response represented by the μ(I) scalar model works well at describing the lower-order aspects of the rheology, except near the quasistatic limit of these stress-controlled flows. The pressure is varied over five decades, and a pressure dependence of the coordination number is observed, which is not captured by the inertial number. Large fluctuations observed for small systems N≤1000 near the quasistatic limit can lead to the arrest of flow resulting in challenges to fitting the data to rheological relationships. The inertial number is also insufficient for capturing the pressure-dependent behavior of property fluctuations. Fluctuations in the flow and microstructural properties are measured in both the quasistatic and inertial regimes, including shear stress, pressure, strain rate, normal stress differences, volume fraction, coordination number, and contact fabric anisotropy. The fluctuations in flow properties scale self-similarly with pressure and system size. A transition in the scaling of fluctuations of stress properties and contact fabric anisotropy are measured and proposed as a quantitative identification of the transition from inertial to quasistatic flow.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Layered supramolecular hydrogels from thioglycosides

Low molecular weight hydrogels are made of small molecules that aggregate via noncovalent interactions. Here, comprehensive characterization of the physical and chemical properties of hydrogels made from thioglycolipids of the disaccharides lactose and cellobiose with simple alkyl chains is reported. While thiolactoside hydrogels are robust, thiocellobioside gels are metastable, precipitating over time into fibrous crystals that can be entangled to create pseudo-hydrogels. Rheology confirms the viscoelastic solid nature of these hydrogels with storage moduli ranging from 10–600 kPa. Additionally, thiolactoside hydrogels are thixotropic which is a desirable property for many potential applications. Freeze-fracture electron microscopy of xerogels shows layers of stacked sheets that are entangled into networks. These structures are unique compared to the fibers or ribbons typically reported for hydrogels. Differential scanning calorimetry provides gel-to-liquid phase transition temperatures ranging from 30 to 80 °C. Prodan fluorescence spectroscopy allows assignment of phase transitions in the gels and other lyotropic phases of high concentration samples. Phase diagrams are estimated for all hydrogels at 1–10 wt% from 5 to ≥ 80 °C. In conclusion, these hydrogels represent a series of interesting materials with unique properties that make them attractive for numerous potential applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Optimizing the accuracy of viscoelastic characterization with AFM force–distance experiments in the time and frequency domains

Atomic Force Microscopy (AFM) force-distance (FD) experiments have emerged as an attractive alternative to traditional micro-rheology measurement techniques owing to their versatility of use in materials of a wide range of mechanical properties. Here, we show that the range of time dependent behaviour which can reliably be resolved from the typical method of FD inversion (fitting constitutive FD relations to FD data) is inherently restricted by the experimental parameters: sampling frequency, experiment length, and strain rate. Specifically, we demonstrate that violating these restrictions can result in errors in the values of the parameters of the complex modulus. In the case of complex materials, such as cells, whose behaviour is not specifically understood a priori, the physical sensibility of these parameters cannot be assessed and may lead to falsely attributing a physical phenomenon to an artifact of the violation of these restrictions. We use arguments from information theory to understand the nature of these inconsistencies as well as devise limits on the range of mechanical parameters which can be reliably obtained from FD experiments. The results further demonstrate that the nature of these restrictions depends on the domain (time or frequency) used in the inversion process, with the time domain being far more restrictive than the frequency domain. Lastly, we demonstrate how to use these restrictions to better design FD experiments to target specific timescales of a material's behaviour through our analysis of a polydimethylsiloxane (PDMS) polymer sample.

information theory↗
DOE OSTI2024

Chain dynamics of alternating polymers P(C n EG 4 )

Alternating or sequence defined polymers attract the attention of an increasing number of researchers recently. Due to their different blocks, they are very customizable and material properties can be tuned. In this publication, we present dynamical studies with focus on polymer dynamics, investigated by rheology and fast field cycling (FFC) NMR. The molecular weight dependencies of the relaxation time and zero-shear viscosity could hint to entanglement effects; however, the spectral shape of the viscoelastic data resembles the polymer dynamics of unentangled melts. Furthermore, taking both techniques into account, i.e. rheology and FFC NMR leads to the conclusion that the relaxation spectra of the alternating polymer are similar to those of linear polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling Electrochemical and Rheological Characteristics of Suspension-Based Electrodes for Redox Flow Cells

Flowable suspension-based electrodes (FSEs) have gained attention in recent years, as the integration of solid materials into electrochemical flow cells can offer improved performance and flexible operation. However, under conditions that engender favorable electrochemical properties (e.g., high particle loading, high conductivity, high surface area), FSEs can exhibit non-Newtonian characteristics that impose large pumping losses and flow-dependent transport rates. These multifaceted trade-offs motivate the use of models to broadly explore scaling relationships and better understand design rules for electrochemical devices. To this end, we present a one-dimensional model, integrating porous electrode theory with FSE rheology as well as flow-dependent electron and mass transport under pressure-driven flow. We study FSE behavior as a function of material properties and operating conditions, identifying key dimensionless groups that describe the underlying physical processes. We assess flow cell performance by quantifying electrode polarization and relative pumping losses, establishing generalized property-performance relationships for FSEs. Importantly, we expound relevant operating regimes—based on a subset of dimensionless groups—that inform practical operating envelopes, ultimately helping to guide FSE and cell engineering for electrochemical systems.

25 ENERGY STORAGE↗
DOE OSTI2022

Mechanical response and microstructure evolution from multiaxial stress relaxation in textured zircaloy nuclear cladding

Modern energy markets provide motivation for nuclear reactors to increase operational flexibility and load following capacity of existing reactor designs. The operational power changes result in fuel pellet expansion and contraction resulting in pellet-cladding mechanical interaction (PCMI) and high cladding stresses that are strongly related to stressed corrosion cracking (SCC) which can lead to fuel rod failure. This work aims to quantify the stress fields in cladding with a focus on multiaxial stress relaxation response from an imposed strain and the resulting microstructure changes in textured zircaloy claddings. Stress relaxation tests resulting in multiaxial stress fields are performed to measure the material response of Zircaloy-4 nuclear cladding. Multiple experiments using samples from the same piece of cladding are performed so samples with the same processing history may be removed at strategic points throughout mechanical testing for microstructure characterization. The microstructure evolution is analyzed with mechanical response to evaluate the static recovery impact on crystallographic texture and grain morphology. Experiments are performed at Idaho National Laboratory using an experimental device capable of applying internal pressure and independent axial load to commercial nuclear cladding at elevated temperatures with stress- or strain-controlled experimental capability. X-ray diffraction and electron backscatter diffraction are used for microstructure analysis. Rheological models are used to visualize the multiaxial stress-strain relationships and isolate elastic, plastic, and viscoplastic material properties for analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Polymer-Grafted Cellulose Nanofibrils with Enhanced Interfacial Compatibility for Stronger Poly(lactic acid) Composites

Cellulose nanofibrils (CNFs) are a promising reinforcement for biodegradable composite matrices such as poly(lactic acid) (PLA), but they require commercially scalable drying methods that preserve their fibrillar morphology along with improved interfacial interactions with polymer matrices. In this work, a water-based grafting-through polymerization scheme to modify CNFs improved spray drying behavior and reinforcement capacity in PLA composites. All polymer modifications yielded CNFs with a more fibrillar morphology after spray drying, increasing specific surface area by up to 490% compared to unmodified CNFs, values similar to conventional freeze drying. Polymer-grafted CNFs in PLA composites improved the tensile strength by 16% at 20 wt % loading and stiffness by 22% at a 10 wt % loading with two different graft-polymer chemistries compared to unmodified CNF composites. Surface energy heterogeneity measurements of the reinforcements and PLA matrix were employed to understand the improvements in composite properties. Polymer modifications lowered the total surface energy of the CNFs, and calculated ratios of work of adhesion to work of cohesion suggested improved interfacial compatibility for four of the modified CNFs with PLA. Rheological oscillatory shear studies of the composites correlated solid-like melt behavior, as demonstrated by storage moduli dominance, with higher tensile strength. Thermal analysis of the composites revealed that excessive plasticization by the poly(oligoethylene glycol methyl ether methacrylate)-grafted sample potentially offset mechanical property improvements imparted by the more fibrillar morphology. This work provides an opportunity for large-scale manufacturing of CNF/PLA composites via an entirely aqueous modification scheme and industrially relevant spray drying process.

36 MATERIALS SCIENCE↗
DOE OSTI2020

4D Printing via an Unconventional Fused Deposition Modeling Route to High-Performance Thermosets

An unprecedented four-dimensional (4D) printing process allowing high-performance and shape memory thermoset to be printed, for the first time, by fused deposition modeling (FDM) with isotropic properties has been achieved. Here, bisphenol A-based epoxy and benzoxazine were formulated to a low-temperature thermoplastic and high-temperature thermoset resin, which is melt-extrudable and can be postcured into covalently cross-linked material. Carbon nanotube (CNT) was added in the resin to work as both mechanical enhancement filler and rheology modifier to prevent shape deformation during postcuring process. The cross-layer reaction fuses individual layers into an integrity, thus eliminating layer delamination induced by FDM, offering isotropic mechanical properties regardless of the printing orientations. The highly cross-linked network provides outstanding mechanical strength and superb thermal stability. The excellent shape memory performance with fast recovery rate and large recovery degree is also obtained in the three-dimensional (3D) printed composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Hierarchically Structured Vitrimer Biocomposites for Sustainable Manufacturing

Polymers containing dynamic covalent bonds (DCBs) exhibit thermoplastic-like flow above their topology freezing temperature (T v ) while maintaining thermoset-like properties below it, making them promising for sustainable manufacturing. However, their large-scale adoption remains limited due to challenges in accurately determining T v and achieving efficient fiber-matrix bonding in composite applications. Here, hierarchically structured epoxy-anhydride-based polyester vitrimer composites reinforced with cellulosic filaments is demonstrated, where hydroxyl groups on fiber surfaces participate directly in transesterification with the matrix. Further, this dynamic interfacial bonding delivers exceptional mechanical properties, including ≈70 MPa shear strength and >10% strain-to-failure, while enabling thermal malleability. Using a combination of nuclear magnetic resonance and nano-infrared spectroscopies, direct evidence is provided that chemical bond exchange begins well below the conventionally measured T v , supporting the hypothesis that rheologically determined T v reflects a combination of chemical exchange and frictional dynamics rather than a discrete transition. The composites demonstrate excellent processability through vacuum-assisted resin transfer molding and maintain >90% of their mechanical properties after multiple thermal reforming cycles. These findings advance both the fundamental understanding of vitrimeric transitions and the practical development of sustainable, high-performance composite materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

In-situ X-ray scattering study of isotactic polypropylene/graphene nanocomposites under shear during fused deposition modeling 3D printing

Complementary techniques were applied to characterize the structure property relationships of FDM printed isotactic polypropylene/graphene nanocomposites. Raman spectroscopy indicated that graphene was mostly exfoliated during the nozzle extrusion process. Rheological measurements of the viscosity indicated that the presence of graphene induced shear thinning during extrusion. Azimuthal scans of wide angle x-ray scattering indicate correlated thermal fluctuations of the graphene platelets which stops abruptly at the onset of transcrystallization, or templating of the iPP chains on the graphene. X-ray microbeam SAXS analysis show the formation of ‘shish-kebab’ structures at the core of the unfilled filaments, where the ‘kebab’ component vanishes at the fiber-fiber interface enabling interdiffusion. Weak lamellar structure, and a corresponding decrease in the storage modulus are observed with the addition of 5% graphene. The lamellar structure disappears entirely with the addition of 10% graphene, while the storage modulus is decreased by nearly 50%. Thermal imaging of heat flux dissipation across molded and printed samples shows no orientational effects in pure iPP despite differences in crystal structure. Thermal conductivity increases dramatically in the samples with 10% graphene, and strong orientational effects are observed where the thermal coefficients differ by 180% between samples printed parallel or perpendicular to the heat flux.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Material extrusion additive manufacturing of wood pulp-reinforced epoxy composites

Direct ink writing (DIW) is an extrusion-based form of 3D-printing that has gained popularity over the last decade. DIW uses thixotropic fluid extrusion to form a particular shape. In order to form stable structures, the rheology of the paste is important to allow for extrusion from the syringe, stability of the growing print, and prevention of unwanted seeping flow during jog moves. In this work, we use wood pulp as a bio-based filler that can provide shear thinning properties to the ink, which produces a stable ink for DIW processing. Additionally, the filler imparts improved mechanical and thermal performance compared to neat resin. The wood pulp provided the shear thinning behavior necessary for DIW printing, and pulp loadings greater than 6 wt%, provided sufficient yield stress so that the composite could self-support during printing. Nanoclay was utilized to further improve ink rheology and appearance to enable larger scale printing. Overall, this work showed successful DIW of an epoxy resin with a sustainable filler improving its stiffness and thermal properties and provides an avenue for further development of bio-based inks for DIW towards various applications.

Lamm, Meghan E. [Oak Ridge National Laboratory (OR↗
DOE OSTI2023

Universal behavior in fragmenting brittle, isotropic solids across material properties

A bonded particle model is used to explore how variations in the material properties of brittle, isotropic solids affect critical behavior in fragmentation. To control material properties, a model is proposed which includes breakable two- and three-body particle interactions to calibrate elastic moduli and mode I and mode II fracture toughnesses. In the quasistatic limit, fragmentation leads to a power-law distribution of grain sizes which is truncated at a maximum grain mass that grows as a nontrivial power of system size. In the high-rate limit, truncation occurs at a mass that decreases as a power of increasing rate. A scaling description is used to characterize this behavior by collapsing the mean-square grain mass across rates and system sizes. Consistent scaling persists across all material properties studied, although there are differences in the evolution of grain size distributions with strain as the initial number of grains at fracture and their subsequent rate of production depend on Poisson's ratio. Importantly, this evolving granular structure is found to induce a unique rheology where the ratio of the shear stress to pressure, an internal friction coefficient, decays approximately as the logarithm of increasing strain rate. The stress ratio also decreases at all rates with increasing strain as fragmentation progresses and depends on elastic properties of the solid.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Design and Production for Maximum Structural Efficiency With Respect to Fiber Orientation With Increased Understanding of Hybrid Fiber Flow Behavior

Discontinuous fiber-reinforced thermoplastic composites have gained considerable attention in automotive, aerospace, and other industries, due to their high-rate of production combined with their ability to attain complex and intricate shapes. Among other high-rate thermoplastic manufacturing processes, injection-molding is one of the most common manufacturing methods due to fast production and high surface finishing of complex geometries. Fiber orientation in discontinuous fiber composites plays a pivotal role in determining the mechanical, electrical, and thermomechanical properties, underscoring the necessity to comprehend fiber orientation in injection molded parts. Among different fiber types, glass and carbon fibers are most common in the composite industries. The recent trend of hybrid composites comprising both glass fiber (GF) and carbon fiber (CF) is also gaining importance in the automotive industry. Hybrid fiber options allow designers to optimize the balance between glass and carbon fibers by leveraging the high durability and low cost of GF while the strength and lightweight properties of CF. Consequently, comparing the fiber oriented distribution (FOD) of injection molded composites containing GF, CF, and a hybrid of GF/CF is critical to investigating the local mechanical properties of intricate structures for high-end applications. In Phase I of this project, FOD in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for GF, CF, and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varies with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Coal polymer composites prepared by fused deposition modeling (FDM) 3D printing

Coal is a vital energy resource worldwide, but pollutants and greenhouse gases from its combustion cause environmental problems. To explore the non-combustion approach to use and valorize coal, anthracite and lignite were blended with polyamide 12 (PA 12) through FDM printing in this work and compared in the composites. By adding lignite, Young’s modulus improved with increasing loading to 50 wt% while tensile strength leveled off among the composites, compared to that of PA 12. By contrast, the addition of anthracite decreased the tensile performance at all loadings. Rheology tests and morphology analyses suggested that the interactions between fillers (anthracite and lignite) and PA 12 may cause differences in tensile properties. In addition, the printed lignite composites showed improved thermal conductivity (~ twofold), indicating lignite demonstrates the potential to build functional composites. This work provides a strategy to use lignite in composites by 3D printing for value-added products and reduces the demand for petroleum-based polymers. Overall, our approach diverts lignite from combustion processes and alleviates the negative impact of lignite use on the environment.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Borehole breakout modeling in arkose and granite rocks

The existence of a deep borehole in the Earth’s crust disturbs the local stresses and creates a stress concentration that may result in breakout and damage to the borehole. Maintaining wellbore integrity mitigates environmental impacts such as groundwater contamination, gas leakage to the atmosphere, and fluid spills and seepage at the surface. In this paper, the stability of deep boreholes (5 km) is examined by laboratory experiments and numerical models in the context of nuclear waste disposal in Israel. Two rock types in southern Israel are considered: the crystalline basement (granite) and the Zenifim Formation (arkose). A series of room-temperature triaxial rock deformation experiments were conducted at different confining pressures. This mechanical characterization was then used to parameterize the elastic properties and damage behavior of the rocks. This facilitated modeling the stability of the deep boreholes by two different formulations of damage rheology: a dynamic-oriented formulation used to model deformation immediately after the creation of the open hole and a quasi-static formulation used to model longer stress corrosion regime. The calibrated modeling results indicate greater stability with Zenifim arkose than the crystalline granite for deep borehole conditions despite the granite having a greater triaxial compressive strength. Dissipation associated with dilation and porous compaction in the arkose during deformation plays a significant stabilizing role in the borehole compared to crystalline rocks. These results suggest that common strength-based borehole stability assessment may lead to inaccurate predictions. Three-dimensional modeling of bottom-hole stress conditions and the effects of transient borehole geometry show conventional two-dimensional analysis may not be conservative when predicting borehole damage.

58 GEOSCIENCES↗
DOE OSTI2025

Recovery of postconsumer mechanically recycled polymers

Mechanical recycling plays a key role in reducing landfill bound plastics that pollute our environment. This process converts plastic waste into marketable pellets by sorting, cleaning, grinding into flakes, compounding in the molten state, and ultimately pelletizing. A primary restriction for the widescale usage of mechanical recycling is the highly variable quality and mechanical properties of the plastic waste feedstock. Degradation can occur during the plastic life cycle with the consumer, during the mechanical processing itself, or during the complex sorting process required to produce the feedstock. This study explores how rheological characterization can mitigate the batch-to-batch variability and identify a potential application for each batch. Shear and extensional rheology of “application-specific” virgin high-density polyethylene (HDPE) and virgin polypropylene (PP) was used as the control for this categorization process. Recycled HDPE and PP from three different streams were then measured and compared to the results from the control study. Rheological measurements proved to be very effective at providing sufficient differentiation to categorize the recycled polymer as suitable for different applications such as injection molding, blow molding, or thermoforming. Finally, the usage of an additional step to sort the recycled polymers by their initial use application was found to achieve a remarkably consistent recovery of application-specific material properties. Furthermore, this secondary sorting could provide significant added value for mechanically recycled polymers.

Differential scanning calorimetry↗
DOE OSTI2022

Depletion-Driven Assembly of Polymer-Coated Nanocrystals

Depletion-driven assembly has been widely studied for micron-sized colloids, but questions remain at the nanoscale where the governing physics are impacted by stabilizing surface ligands or wrapping polymers, whose dimensions are similar to those of the colloidal core and the depletant. Here, we probe how wrapping colloidal tin-doped indium oxide nanocrystals with polymers affects their depletion-induced interactions and assembly in solutions of polyethylene glycol. Copolymers of polyacrylic acid grafted with polyethylene oxide provide nanocrystal wrappings with different effective polymer graft densities and molecular weights. (Ultra) small angle X-ray scattering, coarse-grained molecular dynamics simulation, and molecular thermodynamic theory were combined to analyze how depletant size and polymer wrapping characteristics affect depletion interactions, structure, and phase behavior. The results show how depletant molecular weight, as well as surface density and molecular weight of polymer grafts, set thresholds for assembly. These signatures are unique to depletion-driven assembly of nanoscale colloids and mirror phase behaviors of grafted nanoparticle–polymer composites. Optical and rheological responses of depletion-driven assemblies of nanocrystals with different polymer shell architectures were probed to learn how their structural differences impact properties. Finally, we discuss how these wrinkles for depletion-driven assembly at the nanoscale may provide fresh opportunities for designing responsive depletion interactions and dynamically reconfigurable materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗