Search NASA⌕ Search

SEARCH · Search NASA

Results for “Screw”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

269 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Volatile Fatty Acid Recovery from Arrested Anaerobic Digestion for the Production of Sustainable Aviation Fuel: A Review

The process of producing sustainable aviation fuel (SAF) from organic waste involves the use of volatile fatty acids (VFAs) as intermediates that are obtained via arrested anaerobic digestion (AAD) and VFA recovery. This recovery process often requires several steps, including dewatering, filtration, extraction, and purification. The recovery of VFAs is crucial for their upgrading and can pose a challenge in the production of SAF from organic waste due to high costs and compatibility issues. This review discusses various dewatering methods, including centrifuges, belt filter presses, and screw presses, and explores conditioning technologies that can improve dewatering performance. It also introduces filtration technologies, with a focus on dynamic filtration, which shows promise in addressing the issue of membrane fouling. Additionally, the review describes extraction technologies such as electrodialysis, adsorption, and liquid–liquid extraction (LLE). By providing insights into these different techniques, the review aims to contribute to the development of an integrated VFA recovery process with low carbon footprint.

09 BIOMASS FUELS↗
DOE OSTI2023

Intergranular Spin Dependent Tunneling Dominated Magnetoresistance in Helimagnetic Manganese Phosphide Thin Films

Helical magnets are emerging as a novel class of materials for spintronics and sensor applications; however, research on their charge- and spin-transport properties in a thin film form is less explored. Herein, we report the temperature and magnetic field-dependent charge transport properties of a highly crystalline MnP nanorod thin film over a wide temperature range (2 K < T < 350 K). The MnP nanorod films of ~100 nm thickness were grown on Si substrates at 500 °C using molecular beam epitaxy. The temperature-dependent resistivity ρ(T) data exhibit a metallic behavior (dρ/dT > 0) over the entire measured temperature range. However, large negative magnetoresistance (Δρ/ρ) of up to 12% is observed below ~50 K at which the system enters a stable helical (screw) magnetic state. In this temperature regime, the Δρ(H)/ρ(0) dependence also shows a magnetic field-manipulated CONE + FAN phase coexistence. The observed magnetoresistance is dominantly governed by the intergranular spin dependent tunneling mechanism. These findings pinpoint a correlation between the transport and magnetism in this helimagnetic system.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Spray Drying Enzyme-Treated Cellulose Nanofibrils

Enzyme-treated cellulose nanofibrils (CNFs) were produced via a lab-scale mass colloider using bleached kraft pulp (BKP) to evaluate their processability and power requirements during refining and spray-drying operations. To evaluate the energy efficiency in the CNF refining process, the net energy consumption, degree of polymerization (DP), and viscosity were determined. Less energy was consumed to attain a given fines level by using the endoglucanase enzymes. The DP and viscosity were also decreased using the enzymes. The morphological properties of the enzyme-pretreated spray-dried CNF powders (SDCNFs) were measured. Subsequently, the enzyme-pretreated SDCNFs were added to a PP matrix with MAPP as a coupling agent. The mixture was then compounded through a co-rotating twin-screw extruder to determine whether the enzyme treatment of the CNFs affects the mechanical properties of the composites. Compared to earlier studies on enhancing PMCs with SDCNF powders, this research investigates the use of enzyme-pretreated SDCNF powders. It was confirmed that the strength properties of PP increased by adding SDCNFs, and the strength properties were maintained after adding enzyme-pretreated SDCNFs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Dual Material System for Polymer Large Scale Additive Manufacturing

Big Area Additive Manufacturing (BAAM) technology allows for manufacturing of large-scale objects with a potential to reduce energy embedded in products, reduce or eliminate energy necessary for transportation of goods along with reducing the lead time and cost in some cases. Over the last few years, Oak Ridge National Laboratory (ORNL) has been focusing on large-scale printing of single material systems, typically un-reinforced or short fiber reinforced polymers, in order to address needs in stiffness-limited applications. This paper describes the development of a multi-material large-scale AM system through a collaboration with Cincinnati Inc. and Performance Feed Screw Inc. Modifications to the Big Area Additive Manufacturing (BAAM) system includes a new extruder design to accommodate a dual feed system, an expanded two-dryer system with a capacity of 273 kg/dryer, and a system that is capable of mixing pelletized materials up to 60Kg/hr. This article highlights the advantages and limitations of the multi-material system as well as potential applications.

Smith, Tyler↗
DOE OSTI2021

Characterizing The Internal Morphology of Transition Regions in Large-Scale Extrusion Deposition Additive Manufacturing

A dual-hopper feed system that was developed for the Big Area Additive Manufacturing (BAAM) system allows for transitioning between different materials while maintaining continuous deposition. This technique creates a step-change in material feedstock by switching the pellet feeding system to alternate which hopper is currently supplying material, allowing for multi-material construction. The step-change in feedstock material produces a transition region that is characterized by a compositional gradient and blended internal morphology. Initial cross-sectional imaging of the transition region revealed a non-homogenous blend of materials with distinct domains of each material, likely due to incomplete mixing within the screw. This study used a carbon fiber reinforced acrylonitrile butadiene styrene (CF-ABS) and an unfilled ABS to characterize the internal structure and to correlate it to mechanical performance by tracking microhardness across cross-sections of the transition region.

Brackett, James↗
DOE OSTI2022

THE IMPACT OF A STATIC-MIXING NOZZLE ON UNIFORMITY IN MATERIAL EXTRUSION LARGE-SCALE ADDITIVE MANUFACTURING

There are many methods of incorporating more than one material in Additive Manufacturing (AM) processes. Oak Ridge National Laboratory has developed a unique solution that enables in-situ material switching by developing a dual-hopper feed system for Cincinnati’s Big Area Additive Manufacturing (BAAM) system. Continuous extrusion during a step-change in material feedstock results in a unique blended material transition region that exhibits a heterogeneous internal morphology. To improve mixing of materials during extrusion, a customized static-mixing nozzle was created for use with the BAAM. Single-bead transitions from Material A to B and B to A were printed with the mixing nozzle at a specified screw speed. Compositional analysis tracked the progression of the material transition as a function of extrudate volume. The resulting transition curves were compared against a standard nozzle configuration. Optical microscopy of cross sections also demonstrated that the static-mixing nozzle promoted a more uniform bead geometry as well as a more homogeneous internal structure throughout the material transition.

Brackett, James↗
DOE OSTI2022

Modeling Heat Transfer and Reaction Kinetics of Biomass in Pyrolysis Feeding Systems

Biomass feedstocks can be used to produce low carbon-intensity chemicals and liquid fuels by displacing fossil-fuel sources. Pyrolysis is the thermal decomposition of biomass in the absence of oxygen and can be used to produce crude biofuels. A typical feeding mechanism for pyrolysis reactors is by lock hopper followed by a horizontal auger feeder. Particle agglomeration and plugging of the auger screw are regularly occurring phenomena that is detrimental to the process since it results in the need for periodic inspection and cleaning. The underlying mechanisms leading to agglomeration and plugging are unclear, but a working hypothesis is that heat from the reactor raises the temperature of the biomass in the feeder to the point at which preliminary decomposition reactions occur and produce "sticky" products. Using principles of heat and mass transfer, we derived one-dimensional differential equations for heat flow from the pyrolysis reactor through the auger feeder. Temperature profiles were solved from the system of one-dimensional differential equations using the shooting method. Subsequently, we used the temperature profiles as a one-way coupling to a reaction model for the biomass in the feeder. Kinetic models were adopted from the literature and used to predict the formation of intermediates, products, char, extractives, and metaplastics as well as phase changes along the auger feeder. Species were identified that correlated with softening of the biomass, causing it to become sticky and plug the feeder. We will discuss the details of this work, our findings, and the direction of future work that includes fully coupled transport and reaction-kinetics simulations.

BIOMASS FUELS↗
DOE OSTI2023

Biomass Feedstock Flow Modeling at Exascale

Variable biomass feedstock handling in hoppers and screw conveyors can cause upstream failures and disrupt downstream conversion operations. Understanding how particle size, shape, and moisture content affect feedstock flowability is important for efficient biorefinery operation. We present the use of our open-source discrete element method (DEM) solver for predicting flows in large scale hoppers and assess its performance on state-of-the-art high performance computing platforms that use heterogenous computing architectures.

bioenergy↗
DOE OSTI2022

Long fiber injection molding

An improved method for obtaining high fiber volume fraction, long fiber injection molded articles is provided. According to one embodiment, the method includes forming an injection molding feedstock by cutting pre-impregnated fiber-reinforced tape into platelets. The platelets can be coated with a thin layer of polymer to allow sliding of the platelets with respect to each other at the early stages of plastication, rather than forcing relative motion of fibers with respect to each other. The method can further include the dispersion of material only in the final stages of the injection molding screw to promote gentle motion of the feedstock at the earlier stages of the plastication process. The method allows improvement of mechanical properties of articles manufactured with equipment and techniques that are prevalent in high volume automotive and consumer industries.

Kunc, Vlastimil↗
DOE OSTI2023

Retractable Sensors for In-Core Use in Material Test Reactors - conf paper

Material Test Reactors (MTRs) such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) are used to irradiate nuclear fuels and materials to evaluate their performance after high levels of exposure to a reactor in-core environment. The most critical tests are equipped with instrumentation leads, which allow real-time data collection. However, because of the very harsh environment inside high-power MTR experiments, there are very few sensors that can survive and maintain their calibrated readings for the time periods required to obtain the high neutron doses needed for new fuels and materials qualification. As a result, sometimes sponsoring programs are forced to accept low reliability of sensors, collecting useful data for only part of the experiment duration. The work described herein is based on the observation that MTRs normally run at constant power and the corresponding conditions within reactor experiments typically evolve relatively slowly. Therefore, even one or two measurements per day would provide a complete and representative data set. With this in mind, INL has embarked on a program to develop a mechanism capable of pushing a very small-diameter sensor (typically a thermocouple or optical fiber) into the location to be measured, leave the sensor for roughly 60 seconds to allow it to reach equilibrium and transmit the signal, then pull it up and away from the high neutron flux and high-temperature region. Small-diameter capillary tubes, up to 8 m long, are used to guide the sensors to the appropriate locations. These capillary tubes serve as essentially very deep, thin-walled thermowells. The distance a thermocouple or optical fiber would need to traverse is on the order of 40 - 80 cm. By adopting this infrequent cycling strategy, the thermocouple or optical fiber would spend only a few hours in the high-neutron flux/high-temperature environment over the duration of even the longest irradiation experiment. To date, INL has developed two styles of drive mechanisms. The first is based on friction drive wheels which drive the sensors in a manner similar to a small MIG welder. This has the advantage of being able to accommodate a very long insertion length. The second is based on a ball screw drive and has the advantages of positive attachment and being able to move more than one sensor at a time. Both drive mechanisms have been fabricated and tested in a laboratory setting. Both systems can handle hard mineral insulated cable (such as thermocouples) or optical fibers encased in small diameter tube. The sizes tested to date are 1 - 1.6 mm diameter. Work in this area is ongoing with an eye toward demonstration in the Massachusetts Institute of Technology's MITR reactor, followed by deployment in an ATR irradiation experiment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Retractable Sensors for In-Core Service in Material Test Reactors

Material Test Reactors (MTRs) such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) are used to irradiate nuclear fuels and materials to evaluate their performance after high levels of exposure to a reactor in-core environment. The most critical tests are equipped with instrumentation leads, which allow real-time data collection. However, because of the very harsh environment inside high-power MTR experiments, there are very few sensors that can survive and maintain their calibrated readings for the time periods required to obtain the high neutron doses needed for new fuels and materials qualification. As a result, sometimes sponsoring programs are forced to accept low reliability of sensors, collecting useful data for only part of the experiment duration. The work described herein is based on the observation that MTRs normally run at constant power and the corresponding conditions within reactor experiments typically evolve relatively slowly. Therefore, even one or two measurements per day would provide a complete and representative data set. With this in mind, INL has embarked on a program to develop a mechanism capable of pushing a very small-diameter sensor (typically a thermocouple or optical fiber) into the location to be measured, leave the sensor for roughly 60 seconds to allow it to reach equilibrium and transmit the signal, then pull it up and away from the high neutron flux and high-temperature region. Small-diameter capillary tubes, up to 8 m long, are used to guide the sensors to the appropriate locations. These capillary tubes serve as essentially very deep, thin-walled thermowells. The distance a thermocouple or optical fiber would need to traverse is on the order of 40 - 80 cm. By adopting this infrequent cycling strategy, the thermocouple or optical fiber would spend only a few hours in the high-neutron flux/high-temperature environment over the duration of even the longest irradiation experiment. To date, INL has developed two styles of drive mechanisms. The first is based on counter-rotating wheels which drive the sensors in a manner similar to a small MIG welder. This has the advantage of being able to accommodate a very long insertion length. The second is based on a ball screw drive and has the advantages of positive attachment and being able to move more than one sensor at a time. Both drive mechanisms have been fabricated and tested in a laboratory setting. Both systems can handle hard mineral insulated cable (such as thermocouples) or optical fibers encased in small diameter tube. The sizes tested to date are 1 - 1.6 mm diameter. Work in this area is ongoing with an eye toward demonstration in the Massachusetts Institute of Technology's MITR reactor, followed by deployment in an ATR irradiation experiment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Retractable Sensors for In-Core Service in Material Test Reactors

Material Test Reactors (MTRs) such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) are used to irradiate nuclear fuels and materials to evaluate their performance after high levels of exposure to a reactor in-core environment. The most critical tests are equipped with instrumentation leads, which allow real-time data collection. However, because of the very harsh environment inside high-power MTR experiments, there are very few sensors that can survive and maintain their calibrated readings for the time periods required to obtain the high neutron doses needed for new fuels and materials qualification. As a result, sometimes sponsoring programs are forced to accept low reliability of sensors, collecting useful data for only part of the experiment duration. The work described herein is based on the observation that MTRs normally run at constant power and the corresponding conditions within reactor experiments typically evolve relatively slowly. Therefore, even one or two measurements per day would provide a complete and representative data set. With this in mind, INL has embarked on a program to develop a mechanism capable of pushing a very small-diameter sensor (typically a thermocouple or optical fiber) into the location to be measured, leave the sensor for roughly 60 seconds to allow it to reach equilibrium and transmit the signal, then pull it up and away from the high neutron flux and high-temperature region. Small-diameter capillary tubes, up to 8 m long, are used to guide the sensors to the appropriate locations. These capillary tubes serve as essentially very deep, thin-walled thermowells. The distance a thermocouple or optical fiber would need to traverse is on the order of 40 – 80 cm. By adopting this infrequent cycling strategy, the thermocouple or optical fiber would spend only a few hours in the high-neutron flux/high-temperature environment over the duration of even the longest irradiation experiment. To date, INL has developed two styles of drive mechanisms. The first is based on counter-rotating wheels which drive the sensors in a manner similar to a small MIG welder. This has the advantage of being able to accommodate a very long insertion length. The second is based on a ball screw drive and has the advantages of positive attachment and being able to move more than one sensor at a time. Both drive mechanisms have been fabricated and tested in a laboratory setting. Both systems can handle hard mineral insulated cable (such as thermocouples) or optical fibers encased in small diameter tube. The sizes tested to date are 1 – 1.6 mm diameter. Work in this area is ongoing with an eye toward demonstration in the Massachusetts Institute of Technology’s MITR reactor, followed by deployment in an ATR irradiation experiment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Pyrolysis of Radioactive Spent Resins in the PRIME Installation - 20190

Montair and Belgoprocess developed the pilot PRIME (Pyrolysis Resins In Mobile Electric) Installation for treatment of spent resins in one single reactor without pre-treatment and without intermixing of other waste, allowing for easy traceability and isotopic characterization of the end product. Both low level waste (LLW, < 2 mSv/h) and medium level waste (MLW, > 2 mSv/h) can be treated in the installation. The PRIME pilot installation is designed to treat 2 batches of 100 liter of saturated ion exchange resins over a period of 24 hours. A dosing unit with screw feeder is used for the dosing of the saturated ion exchange resins to the pyrolysis reactor. This completely new developed innovative pyrolysis reactor contains a special design mechanical stirrer and can operate at a temperature of up to 600 deg. C under inert conditions. As a result, the organic molecules will decompose at an accelerated rate until only the mineralized material remains. The lower temperature and the absence of oxygen also prevent the breakdown of ion exchange resins into (powdery) ash, which is a considerable advantage during further handling. Gases that are released during drying and pyrolysis are treated in an also newly developed thermal oxidizer, which uses an innovative, electrically heated design instead of a traditional natural gas- or fuel oil secondary combustion chamber design. After passing through the thermal oxidizer, the gases are cooled down to saturation temperature and treated in the wet scrubbing system. An extraction fan keeps the system under negative pressure to prevent the possibility of any off-gas leakage out of the system. A series of tests were performed successfully with wet cationic resins, anionic resins and a mixture of both. The results of these tests are described in the presentation. For intellectual property protection, the system and process of pyrolysis of organic waste and the system of thermal oxidation of pyrolysis gases described in this paper are patent pending. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Electrospinner Upgrades for Nanofiber Production

Electrospinning is an inexpensive and flexible method for producing nanofibers. Nanofibers are highly adaptable with potential applications in accelerator target systems, air and water filtration, and biomedicine. This project aims to upgrade and test an existing roll-to-roll electrospinner that is more economical for industrial nanofiber production. Varying the diameter of nanofiber can change its functional properties. The current unit cannot adjust spinneret-collector separation, which determines nanofiber diameter. The electro-spinneret channel also does not have lateral adjustment capabilities for precise alignment. Lastly, the viscosities of our polymer solutions have not been quantified. Solution injection into the channel is presently inconsistent because of imperfect nozzle sizing, resulting in waste and decreased efficiency. Modeling was done with Siemens NX CAD software, and viscosity was measured using a Brookfield DVE-LV viscometer. A dual scissor lift design for channel displacement, powered by a dual-shaft DC motor coupled to precision lead screws, was approved and construction was started. Preliminary channel modifications also were initiated. Going forward, the scissor lift system will be integrated and evaluated with our electrospinner, along with further channel modifications. Viscosity measurements of polyvinyldimethylformamide (PVDF) were recorded with inconsistent results due to inadequate testing conditions. Future viscosity trials must be completed in accordance with testing requirements. The optimization and commercialization of roll-to-roll electrospinner units can make nanofiber production more feasible for many new industries and consumer products.

Black, Niko↗
DOE OSTI2023

Development of an interatomic potential for the W–Ta system

A physics-inspired, data-driven interatomic potential framework for multi-element system is presented. This potential is based on the generalization of the embedded atom method potential and systematically incorporates two-, three- and many-body effects. Different atomic environments are described by atom-centered Gaussian basis sets which provides sufficient flexibility to capture diverse atomic environments and allows for easy optimization of the free parameters. An interatomic potential model for the tungsten–tantalum (W–Ta) system is developed using this framework by training on data from ab initio density functional theory (DFT) calculations. The potential is thoroughly tested at various compositions by comparing bulk and defect properties from experimental and DFT data. It is shown that the potential predicts the elastic constants, defect properties, such as vacancy and interstitial formation energies, core structures of dislocations, and melting points for both pure and tantalum and tungsten with an accuracy comparable to other single element machine learning based potentials. In conclusion, the potential model is used to investigate the formation energies of ordered alloys and vacancy formation energies for chemically random W–Ta alloys.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Solutes that reduce yield strength anisotropies in magnesium from first principles

Using Labusch-type solid solution strengthening models parameterized with DFT-computed solute-dislocation interaction energies, we perform a computational search for 63 solutes across the periodic table to find those that lower anisotropy ratios (non-basal to basal CRSS) of magnesium potentially increasing its ductility per the von Mises criterion. For this purpose, we compute changes in strength for solutes as a function of composition and temperature, and compute anisotropy ratios for solutes that include both rare earth and non-rare earth elements. Here we specifically focus on solute-dislocation interaction energies in the following DFT-optimized dislocations as representative of three non-basal plastic deformation modes: $\langle c + a \rangle$ edge, (10$\bar1$2) tension twinning edge, and the (10$\bar{1}$1) compression twinning edge. We find that solute-induced changes in non-basal deformation modes can be approximated using a second-order polynomial in the size misfit of the solutes, which permits rapid screening of solutes. Our approach to identify solutes known to improve strengthening incorporates solute solubility, and suggests other solutes that not have been previously explored for strengthening. The 8 rare-earth solutes that our method suggests as the best, ordered by increasing anisotropy ratios at their optimal concentrations, are: Gd, Tb, Dy, Nd, Ho, Er, Tm, and Yb. The 12 non-rare-earth solutes that our method suggests as the best, ordered by increasing anisotropy ratios, are: Y, Mn, Sc, Pb, Ca, Ag, Bi, Tl, Zn, Li, Ga, and Al. Of these, Gd, Nd, Er, Yb, Y, Mn, Ca, Zn, Li, and Al are used in commercial Mg alloys.

36 MATERIALS SCIENCE↗