Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface segregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The effect of secondary phases on microstructure and irradiation damage in an as-built additively manufactured 316 L stainless steel with a hafnium compositional gradient

Additive manufacturing (AM) or rapid prototyping has become a crucial tool for reducing both cost and time while increasing efficiency in qualifying structural materials for reactor use. In this study, directed energy deposition (DED) was used to develop an as-built 316 L stainless steel sample with three regions of increasing Hf-dopant to study the effects of Hf on the irradiation response of the material. Morphological and microstructural changes were analyzed before and after 2 MeV proton irradiation at 360 °C to a damage of 2.5 dpa at ~ 10 µm below the surface. The addition of Hf effectively suppressed radiation-induced damage (dislocation loops, radiation-induced segregation) due to enhanced point defect recombination. The radiation damage seen in the as-built sample was further compared to a thermo-mechanically treated counterpart of the same fabrication and irradiation parameters which was found to behave superiorly. In conclusion, the increased radiation resistance of this material may be attributed to the as-built microstructure, which includes undissolved Hf particles, delta ferrite grains and cellular sub-grain boundaries that can hinder defect motion.

316L Stainless Steel↗
NASA NTRS1974

Influence of gravity-free solidification on microsegregation

Single crystalline germanium has been grown for the first time in space aboard Skylab Mission No. 2. The crystal growth experiment, designed to characterize the influence of gravity-free solidification on microsegregation of a semiconductor material, contained three crystals. One was doped with Ga; the second with Sb; and the third with B. Portions of the germanium crystals were remelted and subsequently resolidified at 5 microns per second under controlled conditions by the gradient freeze technique. Detailed spreading resistance measurements made on the Ga doped Ge crystals indicate that microsegregation in space is reduced by two to five-fold in the bulk and eight-fold near the surface, while macrosegregation in space is reduced by six-fold in the bulk. The effective segregation coefficient for Ga in Ge was analyzed extensively and was found to be larger for space solidification. This has the implication that the solute boundary layer at the growth interface in space is correspondingly thinner. The solidification interface is significantly smoother and is found to be initially convex toward the melt in space. A convective mixing model has been advanced to explain the absence of gravity on convective mixing and solute segregation during solidification.

Yue, J. T.↗
NASA NTRS1988

Estimating surface soil moisture from satellite microwave measurements and a satellite derived vegetation index

Normalized 18-GHz microwave brightness temperatures, T(B), and a vegetation index determined from satellite radiometer data are combined with climatically modeled surface moisture estimates to constrain a simple physically based soil moisture model. It is found that the normalized T(B) values correlated well with soil moisture when the data were segregated by vegetation index range, but less so when all the data were combined. By using the vegetation index parameter, the model is shown to account for about 70 percent of the variability in modeled surface soil moisture.

Owe, Manfred↗
NASA NTRS2026

Evaluation of Superalloy 718 Additively Manufactured Lattice Blocks

Lattice block structures made up of high temperature superalloys could offer advantages in density, efficiency, and tailored properties. Three candidate lattice designs were screened through additive manufacturing of superalloy 718. Laser powder bed fusion was applied with 718 powder to produce lattice blocks for three-dimensional octahedral unit cell designs of three heights. As-designed versus additively manufactured 718 lattices were compared, including structural dimensions, densities, defects, grain structures, crystallographic texture, and surface residual stresses. Manufactured lattice I diverged the most from its design, with both corner and center nodes merged into continuous columns. Manufactured lattice III came closest to its design, though the actual nodes and struts were still larger in cross section than in the design. Only modest grain coarsening and negligible chemical segregation were observed for all three designs, suggesting uniform thermo-physical and mechanical properties are possible. Significant tensile residual stresses were present at the surface of the manufactured blocks, with highest stresses in the building direction. Current findings indicate this concept could produce useful superalloy structures for high-temperature-capable static components requiring tailored density, and thermo-physical/mechanical properties.

super alloys↗
NASA NTRS2003

Precision Agriculture: Changing the Face of Farming

To a large extent our work has grown out of the remote sensing technology and conceptual framework developed by geologists. For example the drive to look at the physics of reflectance and atmospheric corrections is rooted in work done in the early 1980s by the United States Geological Survey and NASA. Our work on emissivity and thermal behavior of plants pulls on research done using the Thermal Infrared Multispectral Scanner, an instrument originally conceived for geologic applications. Even our ability to geometrically map the airborne imagery onto the globe was explicitly developed because of need to map sediment flow patterns in along the coast of Louisiana. Growing from this base we have learned much in the last few years and believe our integration of geologic remote sensing with the other fields of expertise was a wise investment. Clearly none of the specialties alone could develop, let alone test, the basic approach we are now finding so powerful. This is the path that will ultimately give the information needed by the farmer. We also recognize how small a portion of the total problem has been solved. Having developed the basic logic, built proto-type tools and performed initial tests everything else remains to be done. And problems, scientific and practical, are everywhere. We have not established sensitivities. We have not robustly segregated the contributions of crop residue, soil moisture, shadows, plant and soil to the energy leaving the surface. What we do is extremely expensive and difficult. It is experimental in methodology and uses research oriented tools. We are constantly alive to the practicality of moving our results into commercial applications. We know another airborne instrument will have to be available. Atmospheric parameters will have to be measured automatically. The software will have to be re-written for speed. At times the list of problems seems endless. But the potential is also enormous. Agriculture is a huge portion of our economy. Just a one percent increase in efficiency is a $2,000,000 change. We all depend on farmers, literally for the bread we eat. No other activity of man even has an impact on the land that farming has. If application of precision agriculture can nelp farmers manage their land better, we all may benefit.

Rickman, D.↗
DOE OSTI2023

Elucidating the role of $\mathrm{Fe}$-$\mathrm{Mo}$ interactions in the metal oxide precursors for Fe promoted $\mathrm{Mo/ZSM}$-5 catalysts in non-oxidative methane dehydroaromatization

Literature shows that adding Fe as a separate phase to MoO 3 /ZSM-5 catalysts can improve benzene selectivity in methane dehydroaromatization (MDA), but only when added in small quantities, making it difficult to characterize the state of Fe in the catalyst and understand the role of Fe-Mo interactions on the catalytic properties. We explore how the nature of the Mo-Fe interactions in the catalyst precursor can influence the stability and product selectivity in MDA, by employing for the first time Fe 2 (MoO 4 ) 3 /ZSM-5 as a catalyst precursor in MDA. We have compared the activity of Fe 2 (MoO 4 ) 3 /ZSM-5 with monometallic MoO 3 /ZSM-5 and mixed MoO 3 + Fe 2 O 3 /ZSM-5 containing equivalent Mo and Fe loadings and found that Fe 2 (MoO 4 ) 3 /ZSM-5 shows higher benzene selectivity than the mixed MoO 3 + Fe 2 O 3 /ZSM-5 catalyst and exhibits higher stability in reaction compared to the monometallic MoO3/ZSM-5 catalyst. Structural characterization suggests that Fe 2 (MoO 4 ) 3 partially segregates to Fe 2 O 3 and amorphous MoO x during thermal pretreatment. The MoO x species migrate into the zeolite channels during pretreatment, while Fe oxides remain on the external surface of the zeolite. Gas adsorption/desorption techniques and density functional theory calculations demonstrate that the preexisting Fe 2 O 3 phases on the external surface of the zeolite in the mixed MoO 3 + Fe 2 O 3 /ZSM-5 precursor trap (MoO 3 ) 3 clusters preventing them from migrating into the zeolite channels during pretreatment, whereas gradual formation of amorphous MoOx together with the segregation of the Fe 2 O 3 phase when using the Fe 2 (MoO 4 ) 3 precursor diminishes trapping of (MoO 3 ) 3 and consequently enhances migration and anchoring of the MoO x species in the zeolite channels, boosting selectivity to benzene. Characterization of used catalysts suggests that the presence of Fe promotes formation of structured carbon nanofibers which reduce the rate of catalyst deactivation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Segregation effects during solidification in weightless melts

The generalized problem of determining the temperature and solute concentration profiles during directional solidification of binary alloys with surface evaporation was mathematically formulated. Realistic initial and boundary conditions were defined, and a computer program was developed and checked out. The programs computes the positions of two moving boundaries, evaporation and solidification, and their velocities. Temperature and solute concentration profiles in the semiinfinite material body at selected instances of time are also computed.

Li, C.↗
NASA NTRS2016

The Strata-l Experiment on Microgravity Regolith Segregation

The Strata-1 experiment studies the segregation of small-body regolith through long-duration exposure of simulant materials to the microgravity environment on the International Space Station (ISS). Many asteroids feature low bulk densities, which implies high values of porosity and a mechanical structure composed of loosely bound particles, (i.e. the "rubble pile" model), a prime example of a granular medium. Even the higher-density, mechanically coherent asteroids feature a significant surface layer of loose regolith. These bodies will evolve in response to very small perturbations such as micrometeoroid impacts, planetary flybys, and the YORP effect. A detailed understanding of asteroid mechanical evolution is needed in order to predict the surface characteristics of as-of-yet unvisited bodies, to understand the larger context of samples from sample return missions, and to mitigate risks for both manned and unmanned missions to asteroidal bodies. Due to observation of rocky regions on asteorids such as Eros and Itokawa, it has been hypothesized that grain size distribution with depth on an asteroid may be inhomogeneous: specifically, that large boulders have been mobilized to the surface. In terrestrial environments, this size-dependent sorting to the surface of the sample is called the Brazil Nut Effect. The microgravity and acceleration environment on the ISS is similar that of a small asteroid. Thus, Strata-1 investigates size segregation of regolith in an environment analogous to that of small bodies. Strata-1 consists of four regolith simulants in evacuated tubes, as shown in Figure 1 (Top and Middle). The simulants are (1) a crushed and sieved ordinary chondrite meteorite to simulate an asteroidal surface, (2) a carbonaceous chondrite simulant with a mixture of fine and course particles, and two simplified silicate glass simulants; (3) one with angular and (4) another with spherical particles. These materials were chosen to span a range of granular complexity. The materials were sorted into three size species pre-launch, and maintained during launch and return by a device called the Entrapulator. The hypothesis under test is that the particles that constitute a granular medium in a micro-gravity environment, subjected to a known vibration environemnt, will segregate in accordance to modeled predictions. Strata-1 is currently operating on ISS, with cameras capturing images of simulant motion throughout the one year mission. Vibration data is recorded and downlinked, and the simulants will be analyzed after return to Earth.

Fries, M.↗
DOE OSTI2024

Unraveling the Combined Photothermal Stability of Common Perovskite Solar Cell Compositions

In halide perovskite solar cells, certain compositions, especially those with a high mixture of anions, degrade rapidly. Here, in this study, a degradation study compares the photo (exposure to light), thermal (exposure to elevated temperatures), and photo-plus-thermal (combination) stability of three representative perovskite compositions chosen for their relatively high performance and to independently test anion versus cation effects. Based upon experience and reports, the compositions studied are triple cation with a high Br ratio (Cs 0.05 (FA 0.98 MA 0.02 ) 0.95 Pb(I 0.5 Br 0.5 ) 3 ), all iodide with a moderately high Cs ratio (FA 0.8 Cs 0.2 PbI 3 ), and FA-dominated triple cation (Cs 0.05 (FA 0.98 MA 0.02 ) 0.95 Pb(I 0.98 Br 0.02 ) 3 ). Cs 0.05 (FA 0.98 MA 0.02 ) 0.95 Pb(I 0.98 Br 0.02 ) 3 displayed the best combined photo-plus-thermal stability. Degradation mechanisms were investigated by comparing the morphology, surface composition, and bulk and interface carrier dynamics. Under the harshest aging conditions (photo-plus-thermal), phase segregation and vaporization of organic cations occurred, along with the appearance of high-energy states indicating the interaction with C 60 . The findings were verified on perovskite films blade-coated in air used in devices (FTO/NiOx/SAM/Perovskite/C 60 /BCP/Cu), achieving an efficiency of 21.9% alongside correlated stability.

14 SOLAR ENERGY↗
NASA NTRS1975

Segregation effects during solidification in weightless melts

Computer programs are developed and used in the study of the combined effects of evaporation and solidification in space processing. The temperature and solute concentration profiles during directional solidification of binary alloys with surface evaporation were mathematically formulated. Computer results are included along with an econotechnical model of crystal growth. This model allows: prediction of crystal size, quality, and cost; systematic selection of the best growth equipment or alloy system; optimization of growth or material parameters; and a maximization of zero-gravity effects. Segregation in GaAs crystals was examined along with vibration effects on GaAs crystal growth. It was found that a unique segregation pattern and strong convention currents exist in GaAs crystal growth. Some beneficial effects from vibration during GaAs growth were discovered. The implications of the results in space processing are indicated.

Li, C.↗
DOE OSTI2020

The effect of water vapor on surface oxygen exchange kinetics of thin film (La,Sr)(Co,Fe)O 3-δ

Oxygen reduction and transport in electrochemical applications are strongly affected by the reactant gas composition, including impurities such as water. Understanding the relationship between oxygen reactivity and humidity is key for attaining stability and high efficiency of solid oxide fuel cells, which are especially attractive for transportation applications as low emission power generation devices. Both short- and long-term effects of moisture have previously been associated with use of ambient air. To better understand these effects, we study oxygen exchange kinetics at the cathode surface and the cathode/electrolyte interface using La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) epitaxial thin films as a model-surface system. In situ synchrotron X-ray techniques evaluate the oxygen reduction reaction (ORR) kinetics in response to environmental variables. The results suggest a clear enhancement of the ORR rate upon short term exposure of the perovskite-structured films to water. Finally, on the basis of these measurements, along with in situ X-ray characterization of Sr segregation and computational first-principles studies, we suggest a model for this increased ORR activity that may lead to further improvements by stabilizing active cathode surface configurations.

25 ENERGY STORAGE↗
DOE OSTI2022

Optimization of WAAM Process to Produce AUSC Components with Increased Service Life

Additive manufacturing has the potential to revolutionize industrial hardware and unlock efficiency gains through the fabrication of geometries and architectures not possible by conventional processing. Wire Arc Additive manufacturing (WAAM) process is a class of directed energy deposition process enabling higher build rate and allowing custom wire feedstock allowing spatial variation of microstructure. The larger spot size and lower speed creates a larger melt pool, reducing residual stress and often time creating directional/columnar microstructure for Ni-superalloy. The use of flexible platform provides freedom in deposition strategy, which can accommodate complex substrates, including feature addition onto existing structures, non-flat layers, and repair methods. However, the certification of the final component needs to match the strength requirement. Hence, the quality of the component produced is stringently monitored to avoid buildup of residual stress, cracks, porosity and to reduce detrimental segregated phases commonly observed during alloy solidification. Simulation plays a huge role in predicting the melt pool dimension and can be used to optimize the process parameter. Similar development is also required to perform physics-based modeling of microstructural development in WAAM that can predict the microstructural features during solidification and can be used to optimize the process more effectively. To move toward this goal, Raytheon Technologies Research Center together with Siemens worked to create a set of computational tools to control the process parameters, enable on-line measurements and acquisition with feedback to the optimized process parameters, and eventually track material evolution through each step of the additive process. Computational fluid dynamics is used for accurate prediction and calibration of the thermal field during WAAM process. and phase field models for microstructure evolution as a function of processing parameters to establish a connection between additive parameters and the final microstructure. Here we report cellular automata (CA) model development to predict the dendritic microstructure evolution with surface and bulk nuclei for single track and multiple layers. The CA model was developed to account for secondary element addition and predict segregation, local melting, and latent heat release as well as prediction of Euler angles from orientation information and validated against experiments. This framework was utilized to tailor spatially-varying composition in a part by appropriately controlling the microstructure evolution during the additive process. Functionally graded Haynes 282 alloy with high Cr content at the surface was tested for oxidation and mechanical properties. An advanced physics-based reaction-diffusion model predicting the simultaneous creation of chromium oxide and alumina is developed and validated to extend life expectancy of the WAAM manufactured high temperature part. A machine-learning data-driven framework establishing the process-structure relationship from a dataset of real microstructure images and corresponding process history data has been developed and implemented in the NX Siemens design system. The digital twin configuration along with the tool path generation enabled prediction of WAAM component buildup time and the techno-economic analysis provided a favorable option for all 4 cases with 15-40% cost reduction.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Porous Materials for Water Purification

Abstract Water pollution is a growing threat to humanity due to the pervasiveness of contaminants in water bodies. Significant efforts have been made to separate these hazardous components to purify polluted water through various methods. However, conventional remediation methods suffer from limitations such as low uptake capacity or selectivity, and current water quality standards cannot be met. Recently, advanced porous materials (APMs) have shown promise in improved segregation of contaminants compared to traditional porous materials in uptake capacity and selectivity. These materials feature merits of high surface area and versatile functionality, rendering them ideal platforms for the design of novel adsorbents. This Review summarizes the development and employment of APMs in a variety of water treatments accompanied by assessments of task‐specific adsorption performance. Finally, we discuss our perspectives on future opportunities for APMs in water purification.

Song, Yanpei↗
DOE OSTI2022

Porous Materials for Water Purification

Water pollution is a growing threat to humanity due to the pervasiveness of contaminants in water bodies. Significant efforts have been made to separate these hazardous components to purify polluted water through various methods. However, conventional remediation methods suffer from limitations such as low uptake capacity or selectivity, and current water quality standards cannot be met. Recently, advanced porous materials (APMs) have shown promise in improved segregation of contaminants compared to traditional porous materials in uptake capacity and selectivity. These materials feature merits of high surface area and versatile functionality, rendering them ideal platforms for the design of novel adsorbents. Here, this Review summarizes the development and employment of APMs in a variety of water treatments accompanied by assessments of task-specific adsorption performance. Finally, we discuss our perspectives on future opportunities for APMs in water purification.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Hydrogen trapping energetics at BCC iron-helium interfaces

Density functional theory (DFT) calculations have been performed to assess the trapping and segregation strength of hydrogen (H) to helium (He) interfaces in BCC (Fe) as a function of He density and surface orientation. The He density ranges from 0 to 2 He/V which corresponds to equilibrium bubbles that are expected to form in the structural components in a fusion reactor environment. The DFT calculations consist of a slab of BCC metal and an initial lattice of FCC He. Here, the report on the binding energy of H to these interfaces as well as the migration barriers into and away from the surface, which together provide information on the de-trapping energy for H at He bubbles. It was found that the binding energy of H to He-Fe interfaces decreases with increasing He density. Migration barriers are also modified due to the He density, which are sensitive to the surface orientation as well as the diffusion pathway. These results provide valuable first-principles energetics that are necessary for higher-order, mesoscale models, and provide insight into the extent to which He bubbles may trap tritium in fusion structural materials.

42 ENGINEERING↗
DOE OSTI2024

Selective laser sintering and spark plasma sintering of (Zr,Nb,Ta,Ti,W)C compositionally complex carbide ceramics

Abstract Two advanced manufacturing processes, spark plasma sintering (SPS) and selective laser sintering (SLS), have been developed for synthesis of (Zr,Nb,Ta,Ti,W)C compositionally complex carbide (CCC) via reactive sintering of a powder mixture of constitute monocarbides. X‐ray diffraction analysis confirmed that the single‐phase CCC can be formed by both SPS and SLS. While a homogenous microstructure with uniform metal element distributions was developed during SPS, three‐layer microstructures with a thin TiC‐rich layer and two TaC‐rich layers along with a TiO 2 ‐rich surface layer containing W nanoparticles were formed during SLS. In addition, cellular structures with W, Zr, and Ti element segregation and dislocations on cell boundaries were observed in the SLS‐CCC sample, indicating the effect of nonequilibrium conditions on microstructure formation during laser melting followed by rapid cooling and solidification process. Compared to the SPS‐CCC sample, the SLS‐CCC showed enhanced hardness and reduced thermal conductivity, which may be related to their unique cellular structures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multiscale water drop contact angles at selected silica surfaces

In this paper, multiscale advancing contact angles for glycerol/water drops at silica surfaces are reported for millidrops, submicron-drops, and nanodrops. Selected silica surfaces were muscovite, silicon, and talc. The contact angles for millidrops (1–2 mm) were determined by the traditional sessile drop technique. For submicron-drops (0.1–1.0 μm), a hollow tip Atomic Force Microscope (AFM) procedure was used. The contact angles for nanodrops (~7 nm) were examined from Molecular Dynamics (MD) simulation. The results were compared to evaluate the effect of drop size on the contact angle. In the case of the hydrophobic talc surface, the 75° advancing contact angle did not vary significantly with drop size. For the hydrophilic muscovite surface, the water drop wet the surface and an advancing contact angle of about 10° was found for the millidrops and submicron-drops. However, for the MD simulated nanodrops, attachment and spreading of the ~7 nm drop created a 2D film of molecular dimensions, the contact angle of which was difficult to define and varied from 0° to 17°. Perhaps of equal interest from the MD simulation results was that the spreading of the glycerol/water nanodrop at the muscovite surface resulted in crystallographic directional transport of water molecules to the extremities of the 2D film. Such separation and segregation left the center of the film with an increased concentration of glycerol. Based on these results, the line tension, which has been found in other investigations to account for contact angle decrease with a decrease in drop size, does not seem to be a significant factor in this study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗