Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode interfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Physical and Electrochemical Characterization of Aluminum Electrodes during Electrocoagulation

Electrocoagulation (EC) of synthetic groundwater was conducted using a sacrificial aluminum electrode in a flow-through EC reactor with short retention times (<1 min) under varying hydrodynamic and electrochemical conditions. The treated water was allowed to settle for 24 h and achieved silicate removal of up to 50 ± 4%, and hardness removal of 11 ± 1%. Physical, chemical, and electrochemical characterization was performed to explore changes in electrode surface morphology and composition. Electrochemical impedance spectroscopy (EIS) showed that chemical reactions at the electrode/water interface are sensitive to changes in the immediate chemical environment. We demonstrate that the most energy-intensive step in EC is aluminum dissolution at the anode, which remained fairly constant due to the continuous renewal of the anode’s surface, a result of aluminum dissolution. At the cathode, a structural change in the oxide layer, from γ-Al 2 O 3 to gibbsite, was detected by grazing-incidence X-ray diffraction, which decreased the resistance to charge transfer at the cathode surface, resulting in decreased electrode resistance. The high flow rate in the system minimized the accumulation of aluminum hydroxide solids and aluminum ions at the electrode/water interface, which minimized the formation of thick scalants and amorphous Al(OH) 3 on the cathode and anode, respectively. In conclusion, it was further demonstrated by EIS that under these conditions the resistance to charge transfer was constant throughout the duration of the experiment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Cobalt-free and high-rate stable 5V lithium nickel manganese oxide spinel cathodes enabled via surface oxygen vacancies

Spinel LiNi 0.5 Mn 1.5 O 4 offers both the high-rate, low-cost and safety advantages of LiFePO 4 and the high energy density of LiNiₓMnᵧCo₁₋ₓ₋ᵧO₂ and LiNiₓCoᵧAlzO₂ cathodes. However, the large operating voltage of these materials induces electrolyte oxidation, which degrades the interface and drives Mn dissolution. These reactions are further exacerbated at high rates due to temperature rise. In this study, we discover that ammoniacal treatment followed by annealing introduces a high density of oxygen vacancies in the “near-surface region” of LiNi 0.5 Mn 1.5 O 4 particles. These vacancies release electrons changing the oxidation state of Mn and suppressing its tendency to oxidize the electrolyte. Further, these vacancies enhance the electrode’s electronic conductivity (by ∼3-fold) and Li + diffusivity (by ∼2-fold) greatly improving charge transport, especially when operated at high rates. This results in an across-the-board improvement in self-discharge, specific capacity, energy density, rate capability, coulombic efficiency and cycling stability. When cycled at ∼200 mA g −1 , the capacity fade averaged over 3000 cycles for the surface vacancy-enriched material is ∼0.0167% per cycle compared to an order of magnitude higher fade rate for the baseline material. In conclusion, these findings reveal the potential of targeted surface oxygen vacancy doping to develop cobalt-free and high energy density cathodes that tolerate fast charging and deliver improved cycle life.

Cobalt-free cathodes↗
DOE OSTI2022

Direct Recycling of Lithium-Ion Battery Cathodes: A Multi-Stage Annealing Process to Recover the Pristine Structure and Performance

Direct recycling is an alternative low-cost process that retains the structure of the lithium-ion battery cathode rather than going through materials dissolution and repurification. While the process shows promise, various steps need to be better understood and studied to identify possible roadblocks, cost intensive steps, and needed variations in protocol that may be necessary based on the feedstock of recycled cathodes available. In this study, we have evaluated the process of thermal relithiation as it applies to end-of-life cathode materials. For recovered end-of-life cathodes, approximately 20% of the useable lithium has been lost due to solid electrolyte interface formation, parasitic reactions, and particle isolation; this lost lithium contributes to higher cell impedance and a gradual shift in electrode potentials. As a first step in the direct recycling process, this lithium needs to be restored not only to recover capacity but also to eliminate surface vacancies and hinder surface reconstruction that may increase impedance and impact performance. Here, we have optimized a coating method followed by a two-stage annealing process that restores a model delithiated NMC333 material to pristine performance. Comparisons to single-stage processes are made, and new characterization tools have been used to better understand the processes.

25 ENERGY STORAGE↗
DOE OSTI2025

Decoupling electrode kinetics to elucidate reaction mechanisms in alkaline water electrolysis

Alkaline water electrolysis (AWE) presents key advantages, including reduced material costs, enhanced operational stability, and compatibility with non-precious metal catalysts, positioning it as a scalable route for hydrogen production. In this study, we introduce a minimally invasive single-cell configuration incorporating a reference electrode via diaphragm extension to form an internal ion channel. This setup, combined with an interfaced potentiostat and auxiliary electrometer, enables real-time, independent monitoring of anode and cathode behavior, offering high-resolution electrochemical diagnostics. While it is well established that the hydrogen evolution reaction (HER) exhibits sluggish kinetics in alkaline media, our study reveals that this limitation persists even in practical AWE systems where nickel-based substrates are used as electrodes. This observation is supported by both experimental data and voltage breakdown modeling. Arrhenius-type analysis reveals that localized electric fields induced by catalysts shift the reaction kinetics from classical Butler–Volmer behavior toward a Marcus-like regime, where interfacial molecular dynamics and bimolecular charge transfer dominate. We propose a semi-empirical model and a surficial reaction mechanism to describe these dynamics. This work underscores the critical need for cathode innovation and provides a rational framework for designing advanced catalysts and electrode architectures to optimize AWE performance.

08 HYDROGEN↗
DOE OSTI2023

Unraveling the core of fuel cell performance: engineering the ionomer/catalyst interface

The biggest obstacle to the widespread implementation of polymer electrolyte membrane fuel cells (PEMFCs) is their cost, primarily due to the use of platinum catalysts. The high intrinsic catalyst activity exhibited on a rotating disk electrode (RDE) is rarely realized in a membrane electrode assembly (MEA), which is a long-standing challenge for PEMFCs and a cause of low catalyst utilization. To translate the high RDE performance of a catalyst into a MEA, the design of an ideal ionomer/catalyst interface is proposed: a thin, conformal ionomer film covers the maximum surface of a Pt nanoparticle and thus simultaneously maximizes catalyst utilization, (i.e., high mass activity and electrochemically active surface area) and O 2 diffusion rate (i.e., high current density performance) without compromising proton conduction. Building such an interface is a long-standing challenge due to the lack of interaction between the ionomer and catalyst particles, resulting in large ionomer agglomerates and inhomogeneous ionomer coverage over the catalyst nanoparticle, with consequent poor fuel cell performance. In this work, this ionomer/catalyst interface has been engineered, utilizing the electrostatic attraction between positively charged catalyst and negatively charged ionomer particles in a catalyst ink and preserved in a solid catalyst layer. As a result, this interface leads to previously unachieved proton exchange membrane fuel cell performance in terms of both catalyst utilization (75% vs. 45%) and peak/rated power density (i.e., 1.430/0.930 W cm -2 , H 2 /air, cathode Pt loading: 0.1 mgPt cm -2 ) for pure Pt catalysts, even better than those of Pt alloy catalysts. This work demonstrates the formation of an interface in the liquid phase (using ultra-small-angle X-ray scattering in combination with cryo-TEM, isothermal–titration–calorimetry) and the preservation of the interface in the solid catalyst layer (using TEM) and estimates the effective coverage and thickness of the ionomer film (using limiting current density, RDE and fuel cell performance).

25 ENERGY STORAGE↗
DOE OSTI2022

Regulation of Surface Defect Chemistry toward Stable Ni-Rich Cathodes

Surface reconstruction of Ni-rich layered oxides (NLO) degrades the cycling stability and safety of high-energy-density lithium-ion batteries (LIBs), which challenges typical surface-modification approaches to build a robust interface with electrochemical activity. Here, a strategy of leveraging the low-strain analogues of Li- and Mn-rich layered oxides (LMR) to reconstruct a stable surface on the Ni-rich layered cathodes is proposed. The new surface structure not only consists of a gradient chemical composition but also contains a defect-rich structure regarding the formation of oxygen vacancies and cationic ordering, which can simultaneously facilitate lithium diffusion and stabilize the crystal structure during the (de)lithiation. These features in the NLO lead to a dramatic improvement in electrochemical properties, especially the cyclability under high voltage cycling, exhibiting the 30% increase in capacity retention after 200 cycles at the current density of 1 C (3.0-4.6 V). We report the findings offer a facile and effective way to regulate defect chemistry and surface structure in parallel on Ni-rich layered structure cathodes to achieve high-energy density LIBs.

25 ENERGY STORAGE↗
NASA NTRS2005

Moisture-Induced Spallation and Interfacial Hydrogen Embrittlement of Alumina Scales

Thermal expansion mismatch stresses and interfacial sulfur activity are the major factors producing primary Al2O3 scale spallation on high temperature alloys. However, moisture-induced delayed spallation appears as a secondary, but often dramatic, illustration of an additional mechanistic detail. A historical review of delayed failure of alumina scales and TBC s on superalloys is presented herein. Similarities with metallic phenomena suggest that hydrogen embrittlement from ambient humidity, resulting from the reaction Al+3H2O=Al(OH)3+3H(+)+3e(-), is the operative mechanism. This proposal was tested by standard cathodic hydrogen charging in 1N H2SO4, applied to Rene N5 pre-oxidized at 1150 C for 1000 1-hr cycles, and monitored by weight change, induced current, and microstructure. Here cathodic polarization at -2.0 V abruptly stripped mature Al2O3 scales at the oxide-metal interface. Anodic polarization at +2.0 V, however, produced alloy dissolution. Finally, with no applied voltage, the electrolyte alone produced neither scale spallation nor alloy dissolution. These experiments thus highlight the detrimental effects of hydrogen charging on alumina scale adhesion. It is proposed that interfacial hydrogen embrittlement is produced by moist air and is the root cause of both moisture-induced, delayed scale spallation and desktop TBC failures.

Smialek, James L.↗
NASA NTRS2008

Moisture-Induced Delayed Spallation and Interfacial Hydrogen Embrittlement of Alumina Scales

While interfacial sulfur is the primary chemical factor affecting Al2O3 scale adhesion, moisture-induced delayed spallation appears as a secondary, but impressive, mechanistic detail. Similarities with bulk metallic phenomena suggest that hydrogen embrittlement from ambient humidity, resulting from the reaction Al(sub alloy)+3(H2O)(sub air) = Al(OH)(-) (sub 3) +3H(+) may be the operative mechanism. This proposal was tested on pre-oxidized Rene N5 by standard cathodic hydrogen charging in 1N H2SO4, as monitored by weight change, induced current, and microstructure. Cathodic polarization at -2.0 V abruptly stripped mature Al2O3 scales at the oxide-metal interface. Anodic polarization at +2.0 V, however, produced alloy dissolution. Finally, with no applied voltage, the acid electrolyte produced neither scale spallation nor alloy dissolution. Thus, hydrogen charging was detrimental to alumina scale adhesion. Moisture-induced interfacial hydrogen embrittlement is concluded to be the cause of delayed scale spallation and desktop thermal barrier coating failures.

Smialek, James L.↗
DOE OSTI2026

Conformal hetero-electrolyte interface between soft oxyhalides and garnet enables low-pressure lithium-reservoir-free solid-state batteries

The operation of solid-state batteries with a lithium metal anode and a high voltage cathode requires solid electrolytes (SEs) that are chemically stable with lithium, have a wide electrochemical window, and accommodate volume changes in the electrodes. Unfortunately, no SE has exhibited satisfactory mechanical and electrochemical properties that fit these requirements to date. Dual solid electrolyte systems that use a different SE for the anolyte and catholyte present a viable solution. Here, we focus on oxyhalide SEs that demonstrate superior ionic conductivity and cathode compatibility, where their lithium metal reactivity and poor reduction stability can be resolved using a lithium garnet (Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 , LLZTO) separator. Nonetheless, this imposes a new hetero-electrolyte (H-E) interface at the anolyte|catholyte contact that defines the ion transport across the boundary. We report its promising properties, which are deconvoluted from the electrical measurements of bilayer symmetric cells, for three representative oxyhalide catholytes, LiNbOCl 4 , LiTaOCl 4 , and Li 3 Al 3 O 2 Cl 8 . Pressure-dependent measurements reveal that the relative softness of the oxyhalides (hardness ≤0.4 GPa) enables H-E resistances lower than 150 Ω cm 2 at 2–3 MPa. Mesoscale modelling reveals that the transfer-active contact area of oxyhalides with LLZTO is about 2–3-fold higher than that of argyrodite, Li 6 PS 5 Cl. The low H-E resistance of the LiNbOCl 4 |Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 dual electrolyte enables the cycling of a Li|LiNi 0.82 Mn 0.07 Co 0.11 O 2 full cell with a high discharge capacity (200 mA h g −1 ) at 60 °C and ∼7 MPa. Importantly, we demonstrate a Li-reservoir-free full cell with high Coulombic efficiency (>99.5%) and capacity at 1 MPa using this approach coupled with a garnet-silver interlayer.

Palmer, Max [University of California, Santa Barba↗
DOE OSTI2020

Cathode Electrolyte Diagnostics Based on Scanning Probe Microscopy

Various processes lead to degradation of cathodes in lithium-ion batteries. Questions remain regarding mechanisms of many of these processes. Probe microscopy methods including scanning electrochemical microscopy (SECM) are capable of directly probing processes at the cathode/electrolyte interface. SECM uses a small electrode to perform rapid electrochemical analysis of transient species generated at an active cathode/electrolyte interface. This paper discusses the background of the SECM instrument and its application to lithium-ion battery research. We also describe the application of SECM methods to the study of cathode degradation processes observed in lithium-ion batteries. Specifically, we focus on characterizing the dissolution of manganese from LiMn2O4 (LMO) based on recent debate in the literature. We describe experiments to observe and characterize the electrochemical properties of manganese complexes emerging from degrading LMO electrode materials.

cathode/electrolyte interface↗
DOE OSTI2021

Redox-stable symmetrical solid oxide fuel cells with exceptionally high performance enabled by electrode/electrolyte diffuse interface

Here, in this study, we report a high performance and redox-stable symmetrical solid oxide fuel cell (SOFC) based on (Ba 0.5 Sr 0.5 ) (Mo 0.1 Fe 0.9 )O 3-δ (BSMF) electrode and La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ (LSGM) electrolyte. BSMF is able to operate both as anode and cathode. Excellent electrocatalytic activity has been achieved on BSMF towards hydrogen oxidation and oxygen reduction. Due to its closely matched lattice parameter to LSGM electrolyte, a unique diffuse interface is formed between BSMF and LSGM. Compared to a clean interface, e.g. BSMF/gadolinium doped ceria interface, this diffuse interface promotes the performance of BSMF electrode 1–1.8 times in 600–800 °C. Polarization resistance of the BSMF/LSGM specimen is as low as 0.047 and 0.007 Ωcm 2 in humidified H 2 and in air at 800 °C, respectively. On the BSMF/LSGM/BSMF symmetrical cell, a maximum power density of 2.28 W/cm 2 is achieved at 800 °C, the highest among with redox-stable ceramic electrodes to the best of our knowledge. Redox stability of this cell is confirmed. The role of anode and cathode is reversed back and forth in different operation modes. No apparent degradation is observed through 4 cycles within a 110 h operation period. These findings demonstrate that (Ba 0.5 Sr 0.5 ) (M o0.1 Fe 0.9 )O 3-δ coupled with LSGM electrolyte is an excellent choice to build a high performance, redox-stable SOFC.

25 ENERGY STORAGE↗
DOE OSTI2020

Multifunctional Films Deposited by Atomic Layer Deposition for Tailored Interfaces of Electrochemical Systems

A new strategy for electrochemical interfaces that utilizes multilayer films deposited by atomic layer deposition (ALD) is introduced. Manganese-rich and nickel-rich cathode oxides were coated with a novel bilayer film of metal fluorides. Subsequent exposure to prolonged, high-voltage electrochemical cycling vs graphite electrodes revealed that the bilayer film can greatly enhance the high-voltage stability of cathode oxides. In particular, in manganese-rich cells, capacity fade due to manganese dissolution was substantially reduced and impedance rise was virtually eliminated. Furthermore, in nickel-rich NMC-811 cells, impedance rise was reduced by ~80%, compared to the NMC-811 baseline, after ~300 h of high-voltage exposure during cycling. Here, the multilayer film strategy presents an exciting opportunity for tailoring designs and materials for electrochemical interfaces in advanced lithium-ion batteries and beyond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enabling High Capacity and Coulombic Efficiency for Li-NCM811 Cells Using a Highly Concentrated Electrolyte

Lithium metal batteries suffer from dendrite formation and the associated safety hazards of thermal runaway reactions. In this study, we report the performances of a highly concentrated electrolyte (HCE) and a dilute LiPF6 electrolyte in lithium metal cells using LiNi 0.8 Co 0.1 Mn0.1O 2 . While the HCE exhibits lower bulk ionic conductivity than the dilute LiPF6 electrolyte, the cell conductivity is higher for the HCE system, indicating higher thermodynamic stability of the electrolyte against the electrodes. Full cell cycling demonstrates higher capacity for the HCE system, which declines as a function of cycle number due to the formation of decomposition products, similar to the dilute LiPF 6 system. The origin of the enhanced performance is the higher stability of the HCE against a Li metal anode as compared to the dilute LiPF 6 electrolyte. Cycling at higher temperatures further enhances the performance of the HCE, which is more thermally stable than the dilute LiPF 6 electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2020

New Approaches to Improved PEM Fuel Cell Catalyst Layers

Polymer-electrolyte membrane (PEM) fuel-cells are one of the most promising energy conversion technologies for renewable clean energy applications. A major challenge preventing their widespread commercialization is achieving high performance with lowloadings of platinum group metal (PGM) catalysts. One of the factors driving performance limitations in the cell is the mass transport losses within the cathode catalyst layers due to sluggish oxygen-reduction reactions occurring at the platinum-ionomer interface, which is believed to be linked to reduced transport of ions and oxygen. A viable solution to reduce the transport resistances in the catalyst layers is to create new ionomers that can provide good ion and oxygen transport needed to accomplish high-performing fuel cell catalysts. Characterization of transport properties of ionomers for various molecular architectures is the key step, in the effort to create and identify the optimized polymer structure with improved transport. Using this approach, Tetramer Technologies and LBNL propose improved fuel-cell catalyst ionomers based on Tetramers proprietary polymer chemistry, as highlighted under subtopic 17a Innovative Approaches Toward Discovery and Development of Improved Ionomers for Polymer Electrolyte Membrane Fuel Cell Catalyst Layer.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Elucidating the Link Between Alkali Metal Ions and Reaction-Transport Mechanisms in Cathode Electrodes for Alkali-ion Batteries

Our long-term goal is to improve the reliability of electrode materials and their ability to transport and store various metal ions for electrochemical energy storage applications. The main objective of this work was to investigate the intrinsic relationship between the role of alkali metal ions and electrochemically driven mechanical stability and kinetic properties of battery materials. The overall question was “What is the role of alkali metal ions on the electrochemical and mechanical behavior of cathode electrodes? Our guiding hypothesis was that intercalation of larger alkali metal ions (Na and K) inevitably alters the coupled transport-reaction processes during battery operation in organic electrolytes, leading to more intensive chemo-mechanical instabilities in cathode electrodes, resulting in rapid capacity fade. To validate the hypothesis, we experimentally characterized the reaction-transport processes and governing forces driving the instability of electrode materials in different alkali metal-ion environments. The project had three main tasks. The first one was to investigate intercalation-induced strains and associated stress generation, and their impact on structural deformations in composite cathode electrodes. The second task focused on identifying potential-dependent dynamic changes in the electrode-electrolyte interface in alkali metal ion batteries. The last task was focused on determining how larger alkali metal ions with slower diffusivity affect the transport-mechanics coupling at faster scan rates, compared to smaller ions with faster diffusivity in electrodes. We shortly provided the outcome of each task in the accomplishment section. This project produced 10 peer-reviewed publications (9 research papers and one review manuscript) and supported two Ph.D. students, who graduated from Oklahoma State University.

25 ENERGY STORAGE↗
DOE OSTI2025

Pristine Interface between Lithium Lanthanum Zirconate and Lithium Manganese Oxide by Pulsed Laser Deposition

Solid state lithium-ion batteries have garnered increasing interest in recent years due to several potential advantages over liquid-electrolyte based systems. The possibility of integrating the lithium garnet oxide, Li 6.75 La 3 Zr 1.75 Ta 0.25 O 12 (LLZTO), with the high voltage cathode, spinel Li x Mn 2 O 4 (LMO), is evaluated here. Thin film bilayer structures are prepared by pulsed laser deposition on MgO (001) substrates and characterized by x-ray diffraction and transmission electron microscopy. The LLZTO is grown by an alternating layer-by-layer deposition of LLZTO and Li 3 N and subsequently annealed for several hours at 575 °C to promote crystallinity. Growth of crystalline LMO with a pristine interface to LLZTO is achieved by gentle heat treatment (500 °C) to remove surface carbonate from the electrolyte and by cathode growth at a low temperature of 250 °C. Higher temperature depositions (330 – 450 °C) result in reaction between the two materials and the appearance of Li 2 MnO 3 , which may be in part due to the presence of excess lithium in the electrolyte layer. Because fully lithiated LiMn 2 O 4 has a voltage of ≈3.7 V versus Li+/Li, the observation of a well-defined interface, free of impurity phases and with no interdiffusion of elements, indicates LLZTO is stable to at least 3.7 V.

Garnet LLZO↗
DOE OSTI2022

Anomalous Thermal Decomposition Behavior of Polycrystalline LiNi 0.8 Mn 0.1 Co 0.1 O 2 in PEO-Based Solid Polymer Electrolyte

we report that replacing liquid electrolytes (LEs) with polymer electrolytes has been considered a promising approach to developing next-generation lithium-ion batteries (LIBs) with high energy density and superior safety. Nevertheless, compared with the extensive research on the electrochemical stability of the cathode/polymer electrolyte interfaces, reports on their thermal behaviors are rare to date. Herein, this work systematically investigates the thermal stability of two typical layered oxide cathodes, LiCoO 2 (LCO) and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811), with poly(ethylene oxide) (PEO) electrolyte and with carbonate LEs, respectively. It is found that the oxygen release from the cathodes plays a central role in thermal runaway. Replacing the LE with PEO electrolyte can considerably improve the thermal stability of LCO, but surprisingly, deteriorate that of NMC811. The reason is that the surface of single-crystalline LCO particles can be effectively passivated by the PEO electrolyte during heating, but PEO cannot sufficiently passivate all the primary particles of NMC811 owing to insufficient interface wettability of PEO electrolyte within the polycrystalline secondary NMC811 particles. The findings in this work collectively formulate valuable guidance for improving the safety of polymer-electrolyte-based as well as other types of all-solid-state lithium-ion batteries.

25 ENERGY STORAGE↗