Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrical conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Efficiency enhancement of InGaN/GaN solar cells with nanostructures

We demonstrate InGaN/GaN multi-quantum-well solar cells with nanostructures operating at a wavelength of 520 nm. Nanostructures with a periodic nanorod or nanohole array are fabricated by means of modified nanosphere lithography. Under 1 sun air-mass 1.5 global spectrum illumination, a fill factor of 50 and an open circuit voltage of 1.9 V are achieved in spite of very high indium content in InGaN alloys usually causing degradation of crystal quality. Both the nanorod array and the nanohole array significantly improve the performance of solar cells, while a larger enhancement is observed for the nanohole array, where the conversion efficiency is enhanced by 51%.

30 DIRECT ENERGY CONVERSION↗

Enhanced photovoltaic performance of nanocrystalline CdTe/ZnO solar cells using sol-gel ZnO and positive bias treatment

The effect of doping and porosity of the n-type ZnO layer on the performance of solution-processed, sintered p-CdTe/n-ZnO nanocrystal photovoltaic (PV) devices is investigated. Amorphous sol-gel ZnO is found to be the best candidate with overall energy conversion efficiencies above 8% obtained if the ZnO is also indium doped. We demonstrate that when such PV devices are left under forward bias (in dark or light), the device efficiency values are raised to at least 9.8%, due to a substantially increased open-circuit voltage and fill-factor. This drastic enhancement is attributed to improved band alignment at the ITO/CdTe interface. The forward-bias treatment is slowly reversed over a period of days to weeks on standing under open circuit conditions, but is readily restored with further voltage treatment. The moderate processing conditions and high efficiency of such devices demonstrate that nanocrystal-based systems are a promising technology for photovoltaics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Studying the Effect of Doping with Nickel on Silicon-Based Solar Cells with a Deep p–n-Junction

It has been shown that the doping of the front side of a solar cell with a deep-level p–n junction with nickel atoms increases short-circuit current density J{sub sc} by 89% and open-circuit voltage V{sub oc} by 19.7%. Additional thermal treatment at 700°C for 1 h increases J{sub sc} by 98.4% and V{sub oc} by 13.18%. It is presumed that the IR radiation conversion efficiency grows because nickel atoms form clusters, these being getter centers for uncontrolled recombinant impurities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Progress in the Development of Fe-Based PGM-Free Electrocatalysts for the Oxygen Reduction Reaction

Development of alternative energy sources is crucial to tackle challenges encountered by the growing global energy demand. Hydrogen fuel, a promising way to store energy produced from renewable power sources, can be converted into electrical energy at high efficiency via direct electrochemical conversion in fuel cells, releasing water as the sole byproduct. One important drawback to current fuel-cell technology is the high content of platinum-group-metal (PGM) electrocatalysts required to perform the sluggish oxygen reduction reaction (ORR). Addressing this challenge, remarkable progress has been made in the development of low-cost PGM-free electrocatalysts synthesized from inexpensive, earth-abundant, and easily sourced materials such as iron, nitrogen, and carbon (Fe–N–C). PGM-free Fe–N–C electrocatalysts now exhibit ORR activities approaching that of PGM electrocatalysts but at a fraction of the cost, promising to significantly reduce overall fuel-cell technology costs. Here in this paper, recent developments in PGM-free electrocatalysis, demonstrating increased fuel-cell performance, as well as efforts aimed at understanding the key limiting factor, i.e., the nature of the PGM-free active site, are summarized. Further improvements will be accomplished through the controlled and/or rationally designed synthesis of materials with higher active-site densities, while at the same time establishing methods to mitigate catalyst degradation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of basic physical properties of Sb 2 Se 3 and its relevance for photovoltaics

Antimony selenide (Sb 2 Se 3 ) is a promising absorber material for thin film photovoltaics because of its attractive material, optical and electrical properties. In recent years, the power conversion efficiency (PCE) of Sb 2 Se 3 thin film solar cells has gradually enhanced to 5.6%. In this article, we systematically studied the basic physical properties of Sb 2 Se 3 such as dielectric constant, anisotropic mobility, carrier lifetime, diffusion length, defect depth, defect density and optical band tail states. Here, we believe such a comprehensive characterization of the basic physical properties of Sb 2 Se 3 lays a solid foundation for further optimization of solar device performance.

14 SOLAR ENERGY↗

MHD thermohydraulics analysis and supporting R&D for DCLL blanket in the FNSF

A Fusion Nuclear Science Facility (FNSF) has been recognized in the fusion community as a necessary facility to resolve the critical technology issues of in-vessel components prior to the construction of a DEMO reactor (Abdou et al., 1996) [1]. Among these components, development of a reliable, low-cost and safe blanket system that provides self-sufficient tritium breeding and efficient conversion of the extracted fusion energy to electricity, while meeting all material, design and configuration limitations is among the most important but still challenging goals. In the recent FNSF study in the US (Kesel et al., 2015) [2], a Dual-Coolant Lead-Lithium (DCLL) blanket has been selected as the main breeding blanket concept. This paper summarizes the most important details of the proposed DCLL blanket design, presents the MHD thermohydraulic analysis for the PbLi flows in the blanket conduits and introduces supporting R&D studies, which are presently ongoing at UCLA. We also discuss the required pre-FNSF R&D in the area of MHD Thermofluids to support the further work on the DCLL blanket design & analysis and its integration into the fusion facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Non-equilibrium processing leads to record high thermoelectric figure of merit in PbTe–SrTe

The broad-based implementation of thermoelectric materials in converting heat to electricity hinges on the achievement of high conversion efficiency. Here we demonstrate a thermoelectric figure of merit ZT of 2.5 at 923 K by the cumulative integration of several performance-enhancing concepts in a single material system. Using non-equilibrium processing we show that hole-doped samples of PbTe can be heavily alloyed with SrTe well beyond its thermodynamic solubility limit of <1 mol%. The much higher levels of Sr alloyed into the PbTe matrix widen the bandgap and create convergence of the two valence bands of PbTe, greatly boosting the power factors with maximal values over 30 μWcm -1 K -2 . Exceeding the 5 mol% solubility limit leads to endotaxial SrTe nanostructures which produce extremely low lattice thermal conductivity of 0.5 Wm -1 K -1 but preserve high hole mobilities because of the matrix/precipitate valence band alignment. The best composition is hole-doped PbTe-8% SrTe.

36 MATERIALS SCIENCE↗

TCF Base Technology-Specific Final Report: Negative Cracked Film Lithography for PERC CdTe

NLR worked with the world's leading thin-film photovoltaic manufacturer - First Solar, an American company - to develop electrical contacting methods that improve the power conversion efficiency of First Solar's cells by 0.5% absolute. We met this milestone but contrary to our hypothesis, these performance gains are not passivation (PERC)-based. Instead, we identified another mechanism by which our micropatterned Al 2 O 3 contacts improve efficiency. Using the results of this project, we will adapt NLR's cracked film lithography intellectual property (IP) toward the application we identified, which is a new route to commercialization.

14 SOLAR ENERGY↗

Pyroelectric Energy Scavenging Techniques for Self-Powered Nuclear Reactor Wireless Sensor Networks

Recent advances in technologies for harvesting waste thermal energy from ambient environments present an opportunity to implement truly wireless sensor nodes in nuclear power plants. These sensors could continue to operate during extended station blackouts and during periods when operation of the plant s internal power distribution system has been disrupted. The energy required to power the wireless sensors must be generated using energy harvesting techniques from locally available energy sources, and the energy consumption within the sensor circuitry must therefore be low to minimize power and hence the size requirements of the energy harvester. Harvesting electrical energy from thermal energy sources can be achieved using pyroelectric or thermoelectric conversion techniques. Recent modeling and experimental studies have shown that pyroelectric techniques can be cost competitive with thermoelectrics in self powered wireless sensor applications and, using new temperature cycling techniques, has the potential to be several times as efficient as thermoelectrics under comparable operating conditions. The development of a new thermal energy harvester concept, based on temperature cycled pyroelectric thermal-to-electrical energy conversion, is outlined. This paper outlines the modeling of cantilever and pyroelectric structures and single element devices that demonstrate the potential of this technology for the development of high efficiency thermal-to-electrical energy conversion devices.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Coordination Polymer Electrocatalysts Enable Efficient CO‐to‐Acetate Conversion

Abstract Upgrading carbon dioxide/monoxide to multi‐carbon C 2+ products using renewable electricity offers one route to more sustainable fuel and chemical production. One of the most appealing products is acetate, the profitable electrosynthesis of which demands a catalyst with higher efficiency. Here, a coordination polymer (CP) catalyst is reported that consists of Cu(I) and benzimidazole units linked via Cu(I)‐imidazole coordination bonds, which enables selective reduction of CO to acetate with a 61% Faradaic efficiency at −0.59 volts versus the reversible hydrogen electrode at a current density of 400 mA cm −2 in flow cells. The catalyst is integrated in a cation exchange membrane‐based membrane electrode assembly that enables stable acetate electrosynthesis for 190 h, while achieving direct collection of concentrated acetate (3.3 molar) from the cathodic liquid stream, an average single‐pass utilization of 50% toward CO‐to‐acetate conversion, and an average acetate full‐cell energy efficiency of 15% at a current density of 250 mA cm −2 .

Luo, Mingchuan↗

Ferroelectric field effect of the bulk heterojunction in polymer solar cells

A ferroelectric field effect in the bulk heterojunction was found when an external electric field (EEF) was applied on the active layer of polymer solar cells (PSCs) during the annealing process of the active layer spin-coated with poly(3-hexylthiophene):[6,6]-phenyl-C{sub 61} butyric acid methyl ester. For one direction field, the short circuit current density of PSCs was improved from 7.2 to 8.0 mA/cm{sup 2}, the power conversion efficiency increased from 2.4% to 2.8%, and the incident photon-to-current conversion efficiency increased from 42% to 49% corresponding to the different EEF magnitude. For an opposite direction field, the applied EEF brought a minus effect on the performance mentioned above. EEF treatment can orientate molecular ordering of the polymer, and change the morphology of the active layer. The authors suggest a explanation that the ferroelectric field has been built in the active layer, and therefore it plays a key role in PSCs system. A needle-like surface morphology of the active film was also discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrical and photovoltaic characteristics of MoS{sub 2}/Si p-n junctions

Bulk-like molybdenum disulfide (MoS{sub 2}) thin films were deposited on the surface of p-type Si substrates using dc magnetron sputtering technique and MoS{sub 2}/Si p-n junctions were formed. The vibrating modes of E{sup 1}{sub 2g} and A{sub 1g} were observed from the Raman spectrum of the MoS{sub 2} films. The current density versus voltage (J-V) characteristics of the junction were investigated. A typical J-V rectifying effect with a turn-on voltage of 0.2 V was shown. In different voltage range, the electrical transporting of the junction was dominated by diffusion current and recombination current, respectively. Under the light illumination of 15 mW cm{sup −2}, the p-n junction exhibited obvious photovoltaic characteristics with a short-circuit current density of 3.2 mA cm{sup −2} and open-circuit voltage of 0.14 V. The fill factor and energy conversion efficiency were 42.4% and 1.3%, respectively. According to the determination of the Fermi-energy level (∼4.65 eV) and energy-band gap (∼1.45 eV) of the MoS{sub 2} films by capacitance-voltage curve and ultraviolet-visible transmission spectra, the mechanisms of the electrical and photovoltaic characteristics were discussed in terms of the energy-band structure of the MoS{sub 2}/Si p-n junctions. The results hold the promise for the integration of MoS{sub 2} thin films with commercially available Si-based electronics in high-efficient photovoltaic devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Tetrahydroquinoxaline Based Small Molecule: PCBM Bulk Heterojunction Solar Cell

We have fabricated solution processed bulk heterojuction (BHJ) solar cell from small molecule (SM) as donor blended with PCBM as an acceptor. The BHJ showed power conversion efficiency (PCE) up to 2.80%. The PCE has been further improved up to 3.80 % after thermal annealing of the SM: PCBM layer. The higher PCE of the photovoltaic devices based on the thermal annealed SM: PCBM blend as compared to SM: PCBM blend is attributed to the increase in the crystalline nature of the blend and hole mobility. The thermal annealing allows not only a broad absorption but also tuning of the inter energy level leading to a higher short circuit current (Jsc) and open circuit voltage (Voc).

14 SOLAR ENERGY↗

A Novel Current Angle Control Scheme in a Current Source Inverter Fed Permanent Magnet Synchronous Motor Drive for Automotive Applications

This paper describes a novel speed control scheme to operate a current source inverter (CSI) driven surface-mounted permanent magnet synchronous machine (SPMSM) for hybrid electric vehicles (HEVs) applications. The idea is to use the angle of the current vector to regulate the rotor speed while keeping the two dc-dc converter power switches on all the time to boost system efficiency. The effectiveness of the proposed scheme was verified with a 3 kW CSI-SPMSM drive prototype.

33 ADVANCED PROPULSION SYSTEMS↗

The potential impact of ZT=4 thermoelectric materials on solar thermal energy conversion technologies.

State-of-the-art methodologies for the conversion of solar thermal power to electricity are based on conventional electromagnetic induction techniques. If appropriate ZT = 4 thermoelectric materials were available, it is likely that conversion efficiencies of 30-40% could be achieved. The availability of all solid state electricity generation would be a long awaited development in part because of the elimination of moving parts. This paper presents a preliminary examination of the potential performance of ZT = 4 power generators in comparison with Stirling engines taking into account specific mass, volume and cost as well as system reliability. High-performance thermoelectrics appear to have distinct advantages over magnetic induction technologies.

36 MATERIALS SCIENCE↗

Back-junction back-contact n-type silicon solar cell with diffused boron emitter locally blocked by implanted phosphorus

The highest energy conversion efficiencies in the field of silicon-based photovoltaics have been achieved with back-junction back-contact (BJBC) silicon solar cells by several companies and research groups. One of the most complex parts of this cell structure is the fabrication of the locally doped p- and n-type regions, both on the back side of the solar cell. In this work, we introduce a process sequence based on a synergistic use of ion implantation and furnace diffusion. This sequence enables the formation of all doped regions for a BJBC silicon solar cell in only three processing steps. We observed that implanted phosphorus can block the diffusion of boron atoms into the silicon substrate by nearly three orders of magnitude. Thus, locally implanted phosphorus can be used as an in-situ mask for a subsequent boron diffusion which simultaneously anneals the implanted phosphorus and forms the boron emitter. BJBC silicon solar cells produced with such an easy-to-fabricate process achieved conversion efficiencies of up to 21.7%. An open-circuit voltage of 674 mV and a fill factor of 80.6% prove that there is no significant recombination at the sharp transition between the highly doped emitter and the highly doped back surface field at the device level.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A new class of tandems: Optically coupled III-V/silicon module with outdoor efficiency exceeding 30%

The aim of this project was to introduce a new class of technology—that of high-efficiency silicon-based tandem photovoltaic (PV) modules—that, with follow-on development, has a clear path to reduced levelized cost of electricity (LCOE) for utility-scale power generation. In particular, the objective of the project was to demonstrate the first 30%-efficient III-V/silicon module in outdoor conditions using a tandem geometry in which the sub-cells are detached physically but coupled optically. In present PV power plants installed in the US, the module makes up only approximately one-third of the cost; area-dependent balance-of-systems (BOS) costs such as installation materials, labor, land, and site prep made up an additional third, and area-independent BOS costs round out the final third. With this pricing structure, (annually averaged) module efficiency is a clear market driver: increase the annual energy output per module and the effective costs translated into $/W of both the module and the area-dependent BOS—two-thirds of the total cost—decrease proportionately. However, the dominant PV technology—flat-plate silicon modules—is reaching its theoretical efficiency limit, and thus a tandem technology in which silicon is coupled with a wider-bandgap cell is a promising route to remain responsive to market forces. As it is not trivial to couple silicon with other cells in conventional two-terminal geometries due to, e.g., lattice mismatch, this project introduced a new, four-terminal configuration using a “PVMirror.” A PVMirror utilizes PV cells as a three-in-one technology—they act as a concentrating mirror, spectrum splitter, and high-efficiency light-to-electricity converter. Light is incident upon a full-aperture dichroic mirror that reflects visible light and transmits infrared light. The transmitted light is absorbed in silicon PV cells that are placed behind the dichroic mirror and that convert IR photons to electricity with high efficiency. The dichroic mirror and silicon PV cells are affixed to a curved glass trough that tracks the sun about a single, North-South axis such that the reflected VIS light is concentrated at a common line focus, at which is placed a second, wider-bandgap GaAs PV cell having high efficiency at shorter wavelengths. The innovation of PVMirrors lies in their design, which maximizes annual energy output and minimizes the constraints placed on the sub-cells. In particular, the cells are free of lattice- and current-matching restrictions, neither cell requires a transparent rear electrode, and either sub-cell can be placed at the focus depending on their relative costs. Furthermore, the greatest benefit of PVMirrors is that they make use of a portion of the diffuse light whereas concentrator tandems cannot. This results in a benefit in energy yield and extends PVMirrors’ competitive range. Over the course of this one-year project, a silicon PVMirror and GaAs receiver were fabricated, characterized, and placed outdoors on a sun tracker, where the efficiency of the tandem “module” was measured for three days. Notable results include the first demonstration of this flexible tandem configuration, a maximum tandem efficiency of 29.6% (just shy of the 30% overall project goal), successful conversion of diffuse light into electricity, a thorough loss analysis indicating a path to over 31% efficiency, and a roadmap to cost-competitive PVMirror tandems using a wide-bandgap polycrystalline PVMirror and a silicon receiver. Development of a >18%-efficient wide-bandgap polycrystalline cell—the key enabler of this envisioned tandem—should be a future research focus. This project has laid the groundwork for a PV technology that, with continued development, has the potential to reach LCOEs as low as $0.03/kWh according to our calculations. Such a system would provide the public with inexpensive, clean solar power.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗