Search NASA⌕ Search

SEARCH · Search NASA

Results for “passivation layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Stratospheric sulfate aerosol in and near the Northern Hemisphere polar vortex - The morphology of the sulfate layer, multimodal size distributions, and the effect of denitrification

Measurements were made of stratospheric sulfate aerosols using a passive cavity aerosol spectrometer and a condensation nucleus counter on a NASA ER-2 aircraft in the Airborne Arctic Stratospheric Experiment of 1989. The problems of representative and accurate sampling and particle evaporation were explicitly addressed in the design of the inlets and reduction of the data. The measurements suggest that the sulfate aerosol is bimodal in the polar vortex above the mass mixing ratio maximum in the sulfate layer. It appears that a nuclei mode of small, newly formed particles exists in this region. A stronger case is made for a nuclei mode in the upper few kilometers of the troposphere and in the lower few kilometers of the stratosphere. This mode is probably a global phenomenon occurring in all seasons. Comparison of denitrified and nondenitrified air suggests that denitrification removes some of the larger sulfate particles.

Wilson, J. G.↗
NASA NTRS2016

Transition Delay in Hypersonic Boundary Layers via Optimal Perturbations

The effect of nonlinear optimal streaks on disturbance growth in a Mach 6 axisymmetric flow over a 7deg half-angle cone is investigated in an e ort to expand the range of available techniques for transition control. Plane-marching parabolized stability equations are used to characterize the boundary layer instability in the presence of azimuthally periodic streaks. The streaks are observed to stabilize nominally planar Mack mode instabilities, although oblique Mack mode disturbances are destabilized. Experimentally measured transition onset in the absence of any streaks correlates with an amplification factor of N = 6 for the planar Mack modes. For high enough streak amplitudes, the transition threshold of N = 6 is not reached by the Mack mode instabilities within the length of the cone, but subharmonic first mode instabilities, which are destabilized by the presence of the streaks, reach N = 6 near the end of the cone. These results suggest a passive flow control strategy of using micro vortex generators to induce streaks that would delay transition in hypersonic boundary layers.

Boundary layer transition↗
NASA NTRS1994

Microwave backscattering and emission model for grass canopies

Microwave radar and radiometer measurements of grasslands indicate a substantial reduction in sensor sensitivity to soil moisture in the presence of a thatch layer. When this layer is wet it masks changes in the underlying soil, making the canopy appear warm in the case of passive sensors (radiometer) and decreasing backscatter in the active case (scatterometer). A model for a grass canopy with thatch will be presented in this paper to explain this behavior and to compare with observations. The canopy model consists of three layers: grass, thatch, and the underlying soil. The grass blades are modeled by elongated elliptical discs and the thatch is modeled as a collection of disk shaped water droplets (i.e., the dry matter is neglected). The ground is homogeneous and flat. The distorted Born approximation is used to compute the radar cross section of this three layer canopy and the emissivity is computed from the radar cross section using the Peake formulation for the passive problem. Results are computed at L-band (1.4 GHz) and C-band (4.75 GHz) using canopy parameters (i.e., plant geometry, soil moisture, plant moisture, etc.) representative of Konza Prairie grasslands. The results are compared to C-band scatterometer measurements and L-band radiometer measurements at these grasslands.

TRT-THEORETICAL↗
NASA NTRS2007

Thin Sea-Ice Thickness as Inferred from Passive Microwave and In Situ Observations

Since microwave radiometric signals from sea-ice strongly reflect physical conditions of a layer near the ice surface, a relationship of brightness temperature with thickness is possible especially during the early stages of ice growth. Sea ice is most saline during formation stage and as the salinity decreases with time while at the same time the thickness of the sea ice increases, a corresponding change in the dielectric properties and hence the brightness temperature may occur. This study examines the extent to which the relationships of thickness with brightness temperature (and with emissivity) hold for thin sea-ice, approximately less than 0.2 -0.3 m, using near concurrent measurements of sea-ice thickness in the Sea of Okhotsk from a ship and passive microwave brightness temperature data from an over-flying aircraft. The results show that the brightness temperature and emissivity increase with ice thickness for the frequency range of 10-37 GHz. The relationship is more pronounced at lower frequencies and at the horizontal polarization. We also established an empirical relationship between ice thickness and salinity in the layer near the ice surface from a field experiment, which qualitatively support the idea that changes in the near-surface brine characteristics contribute to the observed thickness-brightness temperature/emissivity relationship. Our results suggest that for thin ice, passive microwave radiometric signals contain, ice thickness information which can be utilized in polar process studies.

Naoki, Kazuhiro↗
NASA NTRS1989

Hydrogen-silicon carbide interactions

A study of the thermochemistry and kinetics of hydrogen environmental attack of silicon carbide was conducted for temperatures in the range from 1100 C to 1400 C. Thermodynamic maps based on the parameters of pressure and oxygen/moisture content were constructed. With increasing moisture levels, four distinct regions of attack were identified. Each region is defined by the thermodynamically stable solid phases. The theoretically stable solid phases of Region 1 are silicon carbide and silicon. Experimental evidence is provided to support this thermodynamic prediction. Silicon carbide is the single stable solid phase in Region 2. Active attack of the silicon carbide in this region occurs by the formation of gases of SiO, CO, CH4, SiH4, and SiH. Analysis of the kinetics of reaction for Region 2 at 1300 C show the attack of the silicon carbide to be controlled by gas phase diffusion of H2O to the sample. Silicon carbide and silica are the stable phases common to Regions 3 and 4. These two regions are characterized by the passive oxidation of silicon carbide and formation of a protective silica layer.

Eckel, Andrew J.↗
NASA NTRS1990

Hydrogen-silicon carbide interactions

A study of the thermochemistry and kinetics of hydrogen environmental attack of silicon carbide was conducted for temperatures in the range from 1100 C to 1400 C. Thermodynamics maps based on the parameters of pressure and oxygen/moisture content were constructed. With increasing moisture levels, four distinct regions of attack were identified. Each region is defined by the thermodynamically stable solid phases. The theoretically stable solid phases of region 1 are silicon carbide and silicon. Experimental evidence is provided to support this thermodynamic prediction. Silicone carbide is the single stable solid phase in region 2. Active attack of the silicon carbide in this region occurs by the formation of gases of SiO, CO, CH4, SiH4 and SiH. Analyses of the kinetics of reaction for region 2 at 1300 C show the attack of the silicon carbide to be controlled by gas phase diffusion of H2O to the sample. Silicon carbide and silica are the stable phases common to regions 3 and 4. These two regions are characterized by the passive oxidation of silicon carbide and formation of a protective silica layer.

Eckel, Andrew J.↗
NASA NTRS1997

Energy Calibration of the Scintillating Optical Fiber Calorimeter Chamber (SOFCAL)

The Scintillating Optical Fiber Calorimeter (SOFCAL) detector is designed to make direct measures of the primary cosmic ray spectrum from -200 GeV/amu - 20 TeV/amu. The primary particles are resolved into groups according to their charge (p, He, CNO, Medium Z, Heavy Z) using both active and passive components integrated into the detector. The principal part of SOFCAL is a thin ionization calorimeter that measures the electromagnetic cascades that result from these energetic particles interacting in the detector. The calorimeter is divided into two sections: a thin passive emulsion/x-ray film calorimeter, and a fiber calorimeter that uses crossing layers of small scintillating optical fibers to sample the energy deposition of the cascades. The energy determination is made by fitting the fiber data to transition curves generated by Monte Carlo simulations. The fiber data must first be calibrated using the electron counts from the emulsion plates in the calorimeter for a small number of events. The technique and results of this calibration will be presented together with samples of the data from a balloon flight.

Christl, M. C.↗
NASA NTRS2011

What Supergranule Flow Models Tell Us About the Sun's Surface Shear Layer and Magnetic Flux Transport

Models of the photospheric flows due to supergranulation are generated using an evolving spectrum of vector spherical harmonics up to spherical harmonic wavenumber l~1500. Doppler velocity data generated from these models are compared to direct Doppler observations from SOHO/MDI and SDO/HMI. The models are adjusted to match the observed spatial power spectrum as well as the wavenumber dependence of the cell lifetimes, differential rotation velocities, meridional flow velocities, and relative strength of radial vs. horizontal flows. The equatorial rotation rate as a function of wavelength matches the rotation rate as a function of depth as determined by global helioseismology. This leads to the conclusions that the cellular structures are anchored at depths equal to their widths, that the surface shear layer extends to at least 70 degrees latitude, and that the poleward meridional flow decreases in amplitude and reverses direction at the base of the surface shear layer (approx.35 Mm below the surface). Using the modeled flows to passively transport magnetic flux indicates that the observed differential rotation and meridional flow of the magnetic elements are directly related to the differential rotation and meridional flow of the convective pattern itself. The magnetic elements are transported by the evolving boundaries of the supergranule pattern (where the convective flows converge) and are unaffected by the weaker flows associated with the differential rotation or meridional flow of the photospheric plasma.

Hathaway, David↗
NASA NTRS2013

Bismuth Passivation Technique for High-Resolution X-Ray Detectors

The Athena-plus team requires X-ray sensors with energy resolution of better than one part in 3,000 at 6 keV X-rays. While bismuth is an excellent material for high X-ray stopping power and low heat capacity (for large signal when an X-ray is stopped by the absorber), oxidation of the bismuth surface can lead to electron traps and other effects that degrade the energy resolution. Bismuth oxide reduction and nitride passivation techniques analogous to those used in indium passivation are being applied in a new technique. The technique will enable improved energy resolution and resistance to aging in bismuth-absorber-coupled X-ray sensors. Elemental bismuth is lithographically integrated into X-ray detector circuits. It encounters several steps where the Bi oxidizes. The technology discussed here will remove oxide from the surface of the Bi and replace it with nitridized surface. Removal of the native oxide and passivating to prevent the growth of the oxide will improve detector performance and insulate the detector against future degradation from oxide growth. Placing the Bi coated sensor in a vacuum system, a reduction chemistry in a plasma (nitrogen/hydrogen (N2/H2) + argon) is used to remove the oxide and promote nitridization of the cleaned Bi surface. Once passivated, the Bi will perform as a better X-ray thermalizer since energy will not be trapped in the bismuth oxides on the surface. A simple additional step, which can be added at various stages of the current fabrication process, can then be applied to encapsulate the Bi film. After plasma passivation, the Bi can be capped with a non-diffusive layer of metal or dielectric. A non-superconducting layer is required such as tungsten or tungsten nitride (WNx).

Chervenak, James↗
NASA NTRS1984

A comparison between active and passive sensing of soil moisture from vegetated terrains

A comparison between active and passive sensing of soil moisture over vegetated areas is studied via scattering models. In active sensing three contributing terms to radar backscattering can be identified: (1) the ground surface scatter term; (2) the volume scatter term representing scattering from the vegetation layer; and (3) the surface volume scatter term accounting for scattering from both surface and volume. In emission three sources of contribution can also be identified: (1) surface emission; (2) upward volume emission from the vegetation layer; and (3) downward volume emission scattered upward by the ground surface. As ground moisture increases, terms (1) and (3) increase due to increase in permittivity in the active case. However, in passive sensing, term (1) decreases but term (3) increases for the same reason. This self conpensating effect produces a loss in sensitivity to change in ground moisture. Furthermore, emission from vegetation may be larger than that from the ground. Hence, the presence of vegetation layer causes a much greater loss of sensitivity to passive than active sensing of soil moisture.

Fung, A. K.↗
NASA NTRS1985

A comparison between active and passive sensing of soil moisture from vegetated terrains

A comparison between active and passive sensing of soil moisture over vegetated areas is studied via scattering models. In active sensing three contributing terms to radar backscattering can be identified: (1) the ground surface scatter term; (2) the volume scatter term representing scattering from the vegetation layer; and (3) the surface volume scatter term accounting for scattering from both surface and volume. In emission three sources of contribution can also be identified: (1) surface emission; (2) upward volume emission from the vegetation layer; and (3) downward volume emission scattered upward by the ground surface. As ground moisture increases, terms (1) and (3) increase due to increase in permittivity in the active case. However, in passive sensing, term (1) decreases but term (3) increases for the same reason. This self compensating effect produces a loss in sensitivity to change in ground moisture. Furthermore, emission from vegetation may be larger than that from the ground. Hence, the presence of vegetation layer causes a much greater loss of sensitivity to passive than active sensing of soil moisture.

Fung, A. K.↗
NASA NTRS1985

N/P GaAs concentrator solar cells with an improved grid and bushbar contact design

The major requirements for a solar cell used in space applications are high efficiency at AMO irradiance and resistance to high energy radiation. Gallium arsenide, with a band gap of 1.43 eV, is one of the most efficient sunlight to electricity converters (25%) when the the simple diode model is used to calculate efficiencies at AMO irradiance, GaAs solar cells are more radiation resistant than silicon solar cells and the N/P GaAs device has been reported to be more radiation resistant than similar P/N solar cells. This higher resistance is probably due to the fact that only 37% of the current is generated in the top N layer of the N/P cell compared to 69% in the top layer of a P/N solar cell. This top layer of the cell is most affected by radiation. It has also been theoretically calculated that the optimized N/P device will prove to have a higher efficiency than a similar P/N device. The use of a GaP window layer on a GaAs solar cell will avoid many of the inherent problems normally associated with a GaAlAs window while still proving good passivation of the GaAs surface. An optimized circular grid design for solar cell concentrators has been shown which incorporates a multi-layer metallization scheme. This multi-layer design allows for a greater current carrying capacity for a unit area of shading, which results in a better output efficiency.

Desalvo, G. C.↗
NASA NTRS2011

Assessment of Resistance of Bacillus Horneckiae Endospores to UV Radiation and Function of Their Extraneous Layer in Resistance

Spore-forming microbes are highly resistant to various physical and chemical conditions, which include ionizing and UV radiation, desiccation and oxidative stress, and the harsh environment of outer space or planetary surfaces. The spore's resistance might be due to their metabolically dormant state, and/or by the presence of a series of protective structures that encase the interior-most compartment, the core, which houses the spore chromosome. These spores have multiple layers surrounding the cell that are not found in vegetative cells, and some species have an outer layer of proteins and glycoproteins termed the "exosporium" or a fibrous "extraneous layer" (EL). Bacillus horneckiae is an EL-producing novel sporeformer isolated from a Phoenix spacecraft assembly clean room, and it has previously demonstrated resistance to UV radiation up to 1000 J/m(sup 2). The EL appears to bind B. horneckiae spores into large aggregations, or biofilms, and may confer some UV resistance to the spores. Multiple culturing and purification schemes were tried to achieve high purity spores because vegetative cells would skew UV resistance results. An ethanol-based purification scheme produced high purity spores. Selective removal of the EL from spores was attempted with two schemes: a chemical extraction method and physical extraction (sonication). Results from survival rates in the presence and absence of the external layer will provide a new understanding of the role of biofilms and passive resistance that may favor survival of biological systems in aggressive extra-terrestrial environments. The chemical extraction method decreased viable counts of spores and lead to an inconclusive change UV resistance relative to non-extracted spores. The physical extraction method lead to non-aggregated spores and did not alter viability; however, it produced UV resistance profiles similar to non-extracted spores. In addition to the EL-removal study, samples of B. horneckiae spores dried on aluminum coupons and exposed to increasing UV (200-400 nm range) levels (0 to 8.0 x 105 kJ/m(sup 2)) were tested for viability, which indicated that the maximum UV exposure level that still resulted in viable spores was 5.0 x 10? kJ/m(sup 2).

resistance↗
NASA NTRS2008

A Sample of What We Have Learned from A-Train Cloud Measurements

The A-train active sensors CloudSat and CALIPSO provide detailed information about cloud vertical structure. Coarse vertical information can also be obtained from a combination of passive sensors (e.g. cloud liquid water content from AMSR-E, cloud ice properties from MLS and HIRDLS, cloud-top pressure from MODIS and AIRS, and UVNISINear IR absorption and scattering from OMI, MODIS, and POLDER). In addition, the wide swaths of instruments such as MODIS, AIRS, OMI, POLDER, and AMSR-E can be exploited to create estimates of the three-dimensional cloud extent. We will show how data fusion from A-train sensors can be used, e.g., to detect and map the presence of multiple layer/phase clouds. Ultimately, combined cloud information from Atrain instruments will allow for estimates of heating and radiative flux at the surface as well as UV/VIS/Near IR trace-gas absorption at the overpass time on a near-global daily basis. CloudSat has also dramatically improved our interpretation of visible and UV passive measurements in complex cloudy situations such as deep convection and multiple cloud layers. This has led to new approaches for unique and accurate constituent retrievals from A-train instruments. For example, ozone mixing ratios inside tropical deep convective clouds have recently been estimated using the Aura Ozone Monitoring Instrument (OMI). Field campaign data from TC4 provide additional information about the spatial variability and origin of trace-gases inside convective clouds. We will highlight some of the new applications of remote sensing in cloudy conditions that have been enabled by the synergy between the A-train active and passive sensors.

Joiner, Joanna↗
NASA NTRS2020

Assessing the Impact of Soil Layer Depth Specification on the Observability of Modeled Soil Moisture and Brightness Temperature

The utility of hydrologic land surface models (LSMs) can be enhanced by using information from observational platforms, but mismatches between the two are common.This study assesses the degree to which model agreement with observations (observability) is affected by two mechanisms in particular: 1) physical incongruities between the support volumes being characterized and 2) inadequateor inconsistent parameterizations of physical processes. The Noah and Noah-MP LSMs by default characterize surface soil moisture (SSM) in the top 10 cm of the soil column. This depth may be reasonable when comparing against soil moisture from in situ probes centered at 5 cm,but it is notably different from the 5 cm (or less) sensing depth of NASA’s Soil Moisture Active Passive (SMAP) satellite mission. These depth inconsistencies are examined by using thinner model layers in the Noah and Noah-MP LSMs and comparing resultant simulations to in situ and SMAP soil moisture. In addition, a forward radiative transfer model to simulate microwave brightness temperatures (Tbs) is used to facilitate direct comparisons of LSM-based and SMAP-based L-band Tb retrievals. Observability is quantified using Kolmogorov-Smirnov distance values, calculated from empirical cumulative distribution functions of SSM and Tb time series. Experiment results depend on the particular subspace being analyzed (SSM or Tb). This study concludes that therole of increasedsoil layer discretizationon LSM observability is secondary to the influence of component parameterizations, the effects of which dominate systematic differences with observations

SMAP↗
NASA NTRS2020

Determining the Shallow Surface Velocity at the Apollo 17 Landing Site

Many studies have been performed to determine the shallow surface velocity model at the Apollo 17 landing site. The Lunar Seismic Profiling Experiment (LSPE) had both an active component with eight explosive packages (EPs) and a passive experiment collecting data at various time intervals. Using the eight EPs, the initial shallow surface velocity model was determined to be 250 m/s in the first layer of depth 248 m, 1200 m/s with a depth of 927 m in the second layer, and 4000 m/s down to a depth of 2 km in the third layer. Have performed variations on this study to produce new velocity models shown. Recent studies have also been reanalyzing the passive LSPE data and have found three different thermal moonquake event types occurring at different times within the lunar day. The current goal of the project is to collocate the thermal moonquakes to physical surface features to determine the breakdown of lunar rocks. However, to locate shallow surface events, an accurate velocity model is needed. Presented a thermal moonquake location algorithm using first order approximation, including surface events only. To improve these approximations, a shallow surface velocity is needed.

Phillips, D.↗
NASA NTRS2019

An L-Band Brightness Temperature Disaggregation Method Using S-Band Radiometer Data for the Water Cycle Observation Mission (WCOM)

The Water Cycle Observation Mission (WCOM) will build upon previous L and C band passive microwave soil moisture satellite missions. WCOM will consist of a passive microwave synthetic aperture radiometer operating at L, S, and C bands. The WCOM requirements for passive soil moisture are to estimate soil moisture in the top 5 cm of soil layer with an error less than 0.04 cu m/cu m, at 15 km resolution and with a 3-day revisit. A new set of algorithms for these multi-frequency platforms will need to be developed for estimating the data products at the desired resolution. To accomplish this, a brightness temperature (TB) downscaling methodology is developed that uses passive S-band TB (30 km) to downscale L-band TB (50 km) and to estimate soil moisture at a 30 km resolution, based on the linear relationships between the passive signals of L-band and S-band. To test this downscaling method, analysis was performed using PALS data from the Soil Moisture Experiments in 2002 (SMEX02). For this study, 4 km L-band observations were downscaled to 800 m. The root mean square errors (RMSE) between the downscaled TBL at 800m with the observed TBL at 800m are 2.63 K and 1.60 K for H and V polarizations respectively. The results also showed that it was possible to use these disaggregated TB to estimate soil moisture to meet the mission requirement of 0.04 cu m/cu m. These results showed that we can obtain higher resolution soil moisture from L band passive TB with a high accuracy (<0.04 cu m/cu m) by using S-band information.

Disaggregation↗
NASA NTRS1990

Remote measurement of ice thickness on the shuttle external tank surface

A passive technique is proposed for remote measurement of thickness of the ice layer formed on the external tank surface of the Shuttle during the T-2 hours period before launch. It is based on the comparison of the ratios of the intensities of three preselected near-IR wavelength bands scattered from the (test spot) and a neighboring (reference spot) on the tank surface. The Shuttle is uniformly illuminated by a battery of strategically located solar simulator lamps and banks of incadescent lamps during prelaunch period. Thus, there should be adequate radiation in the three selected bands incident on the external tank surface during the test period. It is planned to conduct a feasibility study of the proposed technique before recommending it to the KSC/SSC teams for adoption.

Singh, Jag J.↗