Search NASA⌕ Search

SEARCH · Search NASA

Results for “polymer, ceramic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Microscopy and microstructure of Shuttle thermal protection system materials

Examples of the contribution of microstructural analysis to the development of the Space Shuttle tile insulation system are presented, with photographic examples of the scanning electron microscope (SEM) investigations. After the basic thermal protection system materials had been selected, it was neccessary to analyze the mechanical responses of the combined materials; which included: (1) the polymer strain isolation pad (SIP), (2) the room temperature-vulcanizing silicone rubber bond, (RTV), and (3) rigid ceramic fiber reusable surface insulation (RSI). Microstructural analysis was used to provide information on deformation and fracture mechanisms, load transfer mechanisms, and structural alterations occurring before final failure. Both quantitative and qualitative information was obtained in the open, three-dimensional fibrous structures of the ceramic tiles by means of novel techniques of encapsulation and dissolution.

Newquist, C. W.↗
NASA NTRS2006

The Cutting Edge of High-Temperature Composites

NASA s Ultra-Efficient Engine Technology (UEET) program was formed in 1999 at Glenn Research Center to manage an important national propulsion program for the Space Agency. The UEET program s focus is on developing innovative technologies to enable intelligent, environmentally friendly, and clean-burning turbine engines capable of reducing harmful emissions while maintaining high performance and increasing reliability. Seven technology projects exist under the program, with each project working towards specific goals to provide new technology for propulsion. One of these projects, Materials and Structures for High Performance, is concentrating on developing and demonstrating advanced high-temperature materials to enable high-performance, high-efficiency, and environmentally compatible propulsion systems. Materials include ceramic matrix composite (CMC) combustor liners and turbine vanes, disk alloys, turbine airfoil material systems, high-temperature polymer matrix composites, and lightweight materials for static engine structures.

Source record↗
NASA NTRS2004

Atomic Oxygen Durability Evaluation of a UV Curable Ceramer Protective Coating

The exposure of most silicones to atomic oxygen in low Earth orbit (LEO) results in the oxidative loss of methyl groups with a gradual conversion to oxides of silicon. Typically there is surface shrinkage of oxidized silicone protective coatings which leads to cracking of the partially oxidized brittle surface. Such cracks widen and branch crack with continued atomic oxygen exposure ultimately allowing atomic oxygen to reach any hydrocarbon polymers under the silicone coating. A need exists for a paintable silicone coating that is free from such surface cracking and can be effectively used for protection of polymers and composites in LEO. A new type of silicone based protective coating holding such potential was evaluated for atomic oxygen durability in an RF atomic oxygen plasma exposure facility. The coating consisted of a UV curable inorganic/organic hybrid coating, known as a ceramer, which was fabricated using a methyl substituted polysiloxane binder and nanophase silicon-oxo-clusters derived from sol-gel precursors. The polysiloxane was functionalized with a cycloaliphatic epoxide in order to be cured at ambient temperature via a cationic UV induced curing mechanism. Alkoxy silane groups were also grafted onto the polysiloxane chain, through hydrosilation, in order to form a network with the incorporated silicon-oxo-clusters. The prepared polymer was characterized by H-1 and Si-29 NMR, FT-IR, and electrospray ionization mass spectroscopy. The paper will present the results of atomic oxygen protection ability of thin ceramer coatings on Kapton H as evaluated over a range of atomic oxygen fluence levels.

Banks, Bruce A.↗
NASA NTRS1989

Ceramic Honeycomb Panels

Ceramic honeycomb panels serve as lightweight, heat-resistant structural members. Depending on choice of ceramic materials, panels expected to withstand temperatures as high as 1,800 degree C. Honeycomb structure made by vapor-depositing ceramic on fabric substrate woven in honeycomb pattern, then eliminating substrate by oxidizing it. Fabric made of loosely woven polymer such as polyacrylonitrile. Impregnated with organic binder such as phenolic resin for stiffness.

Cagliostro, Domenick E.↗
NASA NTRS2008

Polymer Coats Leads on Implantable Medical Device

Langley Research Center s Soluble Imide (LaRC-SI) was discovered by accident. While researching resins and adhesives for advanced composites for high-speed aircraft, Robert Bryant, a Langley engineer, noticed that one of the polymers he was working with did not behave as predicted. After putting the compound through a two-stage controlled chemical reaction, expecting it to precipitate as a powder after the second stage, he was surprised to see that the compound remained soluble. This novel characteristic ended up making this polymer a very significant finding, eventually leading Bryant and his team to win several NASA technology awards, and an "R&D 100" award. The unique feature of this compound is the way that it lends itself to easy processing. Most polyimides (members of a group of remarkably strong and incredibly heat- and chemical-resistant polymers) require complex curing cycles before they are usable. LaRC-SI remains soluble in its final form, so no further chemical processing is required to produce final materials, like thin films and varnishes. Since producing LaRC-SI does not require complex manufacturing techniques, it has been processed into useful forms for a variety of applications, including mechanical parts, magnetic components, ceramics, adhesives, composites, flexible circuits, multilayer printed circuits, and coatings on fiber optics, wires, and metals. Bryant s team was, at the time, heavily involved with the aircraft polymer project and could not afford to further develop the polymer resin. Believing it was worth further exploration, though, he developed a plan for funding development and submitted it to Langley s chief scientist, who endorsed the experimentation. Bryant then left the high-speed civil transport project to develop LaRC-SI. The result is an extremely tough, lightweight thermoplastic that is not only solvent-resistant, but also has the ability to withstand temperature ranges from cryogenic levels to above 200 C. The thermoplastic s unique characteristics lend it to many commercial applications; uses that Bryant believed would ultimately benefit industry and the Nation. "LaRC-SI," he explains, "is a product created in a government laboratory, funded with money from the tax-paying public. What we discovered helps further the economic competitiveness of the United States, and it was our goal to initiate the technology transfer process to ensure that our work benefited the widest range of people." Several NASA centers, including Langley, have explored methods for using LaRC-SI in a number of applications from radiation shielding and as an adhesive to uses involving replacement of conventional rigid circuit boards. In the commercial realm, LaRC-SI can now be found in several commercial products, including the thin-layer composite unimorph ferroelectric driver and sensor (THUNDER) piezoelectric actuator, another "R&D 100" award winner (Spinoff 2005).

Source record↗
NASA NTRS1983

Application of modern surface analytical tools in the investigation of surface deterioration processes

Surface profilometry and scanning electron microscopy were utilized to study changes in the surface of polymers when eroded. The X-ray photoelectron spectroscopy (XPS) and depth profile analysis indicate the corrosion of metal and ceramic surfaces and reveal the diffusion of certain species into the surface to produce a change in mechanical properties. Ion implantation, nitriding and plating and their effects on the surface are characterized. Auger spectroscopy analysis identified morphological properties of coatings applied to surfaces by sputter deposition.

Buckley, D. H.↗
NASA NTRS2005

New Fiber Reinforced Waterless Concrete for Extraterrestrial Structural Applications

Commercial use of sulfur concrete on Earth is well established, particularly in corrosive, e.g., acid and salt, environments. Having found troilite (FeS) on the Moon raises the question of using extracted sulfur as a lunar construction mate: iii an attractive alternative to conventional concrete as it does not require water For the purpose of this paper it is assumed that lunar ore is mined, refined, and the raw sulfur processed with appropriate lunar regolith to form, for example, brick and beam elements. Glass fibers produced from regolith were used as a reinforcement to improve the mechanical properties of the sulfur concrete. Glass fibers and glass rebar were produced by melting the lunar regolith simulant. Lunar regolith stimulant was melted in a 25 cc Pt-Rh crucible in a Sybron Thermoline 46100 high temperature MoSi2 furnace at melting temperatures of 1450 to 1600G. The glass melt wets the ceramic rod and long continuous glass fibers were easily hand drawn. The glass fibers were immediately coated with a protective polymer to maintain the mechanical strength. The viability of sulfur concrete as a construction material for extraterrestrial application is presented. The mechanical properties of the glass fiber reinforced sulfur concrete were investigated.

Toutanji, H.↗
NASA NTRS2008

Mechanical Properties and Durability of "Waterless Concrete"

Waterless concrete consists of molten elementary sulfur and aggregate. The aggregates in lunar environment will be lunar rocks and soil. Sulfur is present on the Moon in Troilite soil (FeS) and by oxidation soil iron and sulfur can be produced. Iron can be used to reinforce the sulfur concrete. Sulfur concrete specimens were cycled between liquid nitrogen (approximately 191 C) and room temperature (approximately 21 C) to simulate exposure to a lunar environment. Cycled and control specimens were subsequently tested in compression at room temperatures (approximately 21 C) and approximately 101 C. Test results showed that due to temperature cycling, compressive strength of cycled specimens was 20% of those non-cycled. Microscopic examination of the fracture surfaces from the cycled samples showed clear de-bonding of the sulfur from the aggregate material whereas it was seen well bonded in those non-cycled. This reduction in strength can be attributed to the large differences in thermal coefficients of expansion of the materials constituting the concrete which promoted cracking. Similar sulfur concrete mixtures were strengthened with short and long glass fibers. The glass fibers from lunar regolith simulant was melted in a 25 cc Pt-Rh crucible in a Sybron Thermoline high temperature MoSi2 furnace at melting temperatures of 1450 to 1600 C for times of 30 min to 1 hour. Glass fibers were cast from the melt into graphite crucibles and were annealed for a couple of hours at 600 C. Glass fibers and small rods were pulled from the melt. The glass melt wets the ceramic rod and long continuous glass fibers were easily hand drawn. The glass fibers were immediately coated with a protective polymer to maintain the mechanical strength. The glass fibers were used to reinforce sulfur concrete plated to improve the flexural strength of the sulfur concrete. Prisms beams strengthened with glass fibers were tested in 4-point bending test. Beams strengthened with glass fiber showed to exhibit an increase in the flexura strength by as much as 45%.

Toutanji, Houssam↗
NASA NTRS1991

Material issues for lunar/Martian structures

Development of structures in the lunar/Martian environment depends upon the use of the most appropriate materials. Advanced composite materials are apparently the best candidates for use in structures on planetary surfaces and in space in view of their unique properties, tailorability and light weight. The physical and mechanical properties of advanced composite materials as related to their use in lunar/Martian structures are reviewed. Polymer matrix composites are recommended as the best materials in the first exploration stages of a lunar/Martian base. Increased use of ceramic and metal matrix composites is expected in the more advanced exploration stages. The pressing need for the development of tailored radiation shielding composite materials is discussed.

Radford, Donald W.↗
NASA NTRS1998

A Novel Ultrasonic Method for Characterizing Microstructural Gradients in Tubular Structures

Ultrasonic velocity and time-of-flight (TOF) imaging that uses back surface reflections to gage volumetric material quality is highly suited for quantitative characterization of microstructural gradients including those due to pore fraction, density, fiber fraction, and chemical composition variations. However, a weakness of conventional pulse echo ultrasonic velocity and TOF imaging is that the image shows the effects of thickness as well as microstructural variations, unless the part is uniformly thick. This limits this imaging method's usefulness in practical applications. Prior studies have described a pulse echo TOF based ultrasonic imaging method that requires using a single transducer in combination with a reflector plate placed behind samples which, eliminates the effect of thickness variation in the image. In those studies, this method was successful at isolating ultrasonic variations due to material in plate like samples of silicon nitride, metal matrix composite, and polymer matrix composite. In this study, the method is engineered for inspection of more complex shaped structures- those having (hollow) tubular or curved geometry. The experimental inspection technique and results are described as applied to a polymer matrix composite "proof of concept" tube that contains machined patches of various depths and an as manufactured monolithic silicon nitride ceramic tube that might be used in "real world" applications.

Roth, Don J.↗
NASA NTRS1990

Polysiloxanes derived from the controlled hydrolysis of tetraethoxysilane as precursors to silica for use in ceramic processing

Synthesis, properties, and potential applications in ceramic processing for two polysiloxane silica precursors derived from the controlled hydrolysis of tetraethoxysilane (TEOS) are presented. The higher molecular weight TEOS-A is a thick adhesive liquid of viscosity 8000 to 12,000 c.p. having a SiO2 char yield of about 55 percent. The lower molecular weight TEOS-B is a more fluid liquid of viscosity 150 to 200 c.p. having a SiO2 char yield of about 52 percent. The acid catalyzed hydrolysis of TEOS to hydrated silica gel goes through a series of polysiloxane intermediates. The rate of this transition increases with the quantity of water added to the TEOS; thus, for ease of polymer isolation, the amount of water added must be carefully determined so as to produce the desired polymer in a reasonable time. The water to TEOS mole ratio falls in the narrow range of 1.05 for TEOS-A and 0.99 for TEOS-B. Further polymerization or gelation is prevented by storing at -5 C in a freezer. Both polysiloxanes thermoset to a glassy solid at 115 C. The liquid polymers are organic in nature in that they are miscible with toluene and ethanol, slightly souble in heptane, but immiscible with water. For both polymers, results on viscosity versus time are given at several temperatures and water additions. Based on these results, some examples of practical utilization of the precursors for ceramic fabrication are given.

Philipp, Warren H.↗
NASA NTRS2017

2017 NEPP Tasks Update for Ceramic and Tantalum Capacitors

This presentation gives an overview of current NEPP tasks on ceramic and tantalum capacitors and plans for the future. It includes tasks on leakage currents, gas generation and case deformation in wet tantalum capacitors; ESR degradation and acceleration factors in MnO2 and polymer cathode capacitors. Preliminary results on the effect of moisture on degradation of reverse currents in MnO2 tantalum capacitors are discussed. Latest results on mechanical characteristics of MLCCs and modeling of degradation of leakage currents in BME capacitors with defects are also presented.

ceramic capacitors↗
NASA NTRS1994

Metal-Ion Additives Reduce Thermal Expansion Of Polyimides

Polyimides widely used as high-performance polymers because of their excellent thermal stability and toughness. However, their coefficients of thermal expansion (CTE's) greater than those of metals, ceramics, and glasses. Decreasing CTE's of polyimides increase usefulness for aerospace and electronics applications in which dimensional stability required. Additives containing metal ions reduce coefficients of thermal expansion of polyimides. Reductions range from 11 to over 100 percent.

Stoakley, Diane M.↗
NASA NTRS2003

Carbon Nanotubes for Human Space Flight

Single-wall carbon nanotubes offer the promise of a new class of revolutionary materials for space applications. The Carbon Nanotube Project at NASA Johnson Space Center has been actively researching this new technology by investigating nanotube production methods (arc, laser, and HiPCO) and gaining a comprehensive understanding of raw and purified material using a wide range of characterization techniques. After production and purification, single wall carbon nanotubes are processed into composites for the enhancement of mechanical, electrical, and thermal properties. This "cradle-to-grave" approach to nanotube composites has given our team unique insights into the impact of post-production processing and dispersion on the resulting material properties. We are applying our experience and lessons-learned to developing new approaches toward nanotube material characterization, structural composite fabrication, and are also making advances in developing thermal management materials and electrically conductive materials in various polymer-nanotube systems. Some initial work has also been conducted with the goal of using carbon nanotubes in the creation of new ceramic materials for high temperature applications in thermal protection systems. Human space flight applications such as advanced life support and fuel cell technologies are also being investigated. This discussion will focus on the variety of applications under investigation.

Scott, Carl D.↗
NASA NTRS2000

Solid Freeform Fabrication of Continuous Fiber Reinforced Composites for Propulsion Applications

For propulsion related applications, materials must be able to demonstrate excellent ablation and oxidation resistance at temperature approaching 3500'C, adequate load bearing capabilities, non-catastrophic failure modes, and ability to withstand transient thermal shock. A potential list of propulsion-material property requirements includes, low density, high elastic modulus, low thermal-expansion coefficient, high thermal conductivity, excellent erosion and oxidation/corrosion resistance, and flaw-insensitivity. In many cases, they will also need to be able to be joined, survive thermal cycling and multi-axial stress states, and for reusable applications, the materials must maintain the above attributes after prolonged exposure to extremely harsh chemical environments. The final and possibly most important attribute for these materials are the need to be lower cost and readily available in large quantities. Recently, Advanced Ceramics Research, Inc. (ACR) has developed low cost, flexible- manufacturing processes for Zr & Hf-based carbon fiber reinforced composites, materials with good oxidation and ablation resistance up to 3500 C. This process, called Continuous Composite Co-extrusion (C(sup 3)), incorporates carbon fibers to fabricate 'in-situ' carbide and boride-matrix/carbon fiber composites. This is a variation of ACR's manufacturing process for low-cost structural ceramic materials called Fibrous Monoliths With carbon fiber reinforcements. Fibrous Monolithic materials have a distinct fibrous texture, consist of intertwined cells of a primary phase, separated by cell boundaries of a tailored secondary phase and show very high fracture energies, damage tolerance, and graceful failure. Since they are monolithic powder based composites-, they can be manufactured by conventional powder processing techniques using inexpensive raw materials. This combination of high performance and low cost is a breakthrough that could enable wider application of ceramics in high temperature applications. Typical volume fractions of the two phases are 80 to 95% for the cell phase and 5 to 20% for the interpenetrating cell boundary phase. ACR is currently developing an innovative solid freeform form fabrication (SFF) approach to produce Hf and Zr based ceramic composite components reinforced with continuous carbon fiber tows for critical structural components such as tubes and blisks. The process is simple, robust and will be widely applicable to a number of material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The current process is being developed in collaboration with UD-CCM. The paper will detail the freeform fabrication process to create low-cost ceramic fiber reinforced composites for high-temperature applications. The results of mechanical properties and microstructural characterization will be presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts for propulsion applications at an order of magnitude lower cost than current CVI and PIP process.

Vaidyanathan, R.↗
NASA NTRS2001

Solid Free-Form Fabrication of Continuous Fiber Reinforced Composites for Propulsion Application

For propulsion related applications, materials must be able to demonstrate excellent ablation and oxidation resistance at temperature approaching 3500 C, adequate load bearing capabilities, non-catastrophic failure modes, and ability to withstand transient thermal shock. A potential list of propulsion-material property requirements includes, low density, high elastic modulus, low thermal-expansion coefficient, high thermal conductivity, excellent erosion and oxidation/corrosion resistance, and flaw-insensitivity. In many cases, they will also need to be able to be joined, survive thermal cycling and multi-axial stress states, and for reusable applications, the materials must maintain the above attributes after prolonged exposure to extremely harsh chemical environments. The final and possibly most important attribute for these materials are the need to be lower cost and readily available in large quantities. Recently, Advanced Ceramics Research, Inc. (ACR) has developed low cost, flexible-manufacturing processes for Zr & Hf-based carbon fiber reinforced composites, materials with good oxidation and ablation resistance up to 3500 C. This process, called Continuous Composite Co-extrusion (C(sup 3)), incorporates carbon fibers to fabricate 'in-situ' carbide and boride-matrix/carbon fiber composites. M is a variation of ACR's manufacturing process for low-cost structural ceramic materials called Fibrous Monoliths with carbon fiber reinforcements. Fibrous Monolithic materials have a distinct fibrous texture, consist of intertwined cells of a primary phase, separated by cell boundaries of a tailored secondary phase and show very high fracture energies, damage tolerance, and graceful failure. Since they are monolithic powder based composites; they can be manufactured by conventional powder processing techniques using inexpensive raw materials. This combination of high performance and low cost is a breakthrough that could enable wider application of ceramics in high temperature applications. Typical volume fractions of the two phases are 80 to 95% for the cell phase and 5 to 20% for the interpenetrating cell boundary phase. ACR is currently developing an innovative solid freeform form fabrication (SFF) approach to produce Hf and Zr based ceramic composite components reinforced with continuous carbon fiber tows for critical structural components such as tubes and blisks. The process is simple, robust and will be widely applicable to a number of material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The current process is being developed in collaboration with UD-CCM. The paper will detail the freeform fabrication process to create low-cost ceramic fiber reinforced composites for high-temperature applications. The results of mechanical properties and microstructural characterization will be presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts for propulsion applications at an order of magnitude lower cost than current CVI and PIP processes.

Vaidyanathan, R.↗
NASA NTRS2008

NASA Tech Briefs, July 2008

Topics covered include: Torque Sensor Based on Tunnel-Diode Oscillator; Shaft-Angle Sensor Based on Tunnel-Diode Oscillator; Ground Facility for Vicarious Calibration of Skyborne Sensors; Optical Pressure-Temperature Sensor for a Combustion Chamber; Impact-Locator Sensor Panels; Low-Loss Waveguides for Terahertz Frequencies; MEMS/ECD Method for Making Bi(2-x)Sb(x)Te3 Thermoelectric Devices; Low-Temperature Supercapacitors; Making a Back-Illuminated Imager with Back-Side Contact and Alignment Markers; Compact, Single-Stage MMIC InP HEMT Amplifier; Nb(x)Ti(1-x)N Superconducting-Nanowire Single-Photon Detectors; Improved Sand-Compaction Method for Lost-Foam Metal Casting; Improved Probe for Evaluating Compaction of Mold Sand; Polymer-Based Composite Catholytes for Li Thin-Film Cells; Using ALD To Bond CNTs to Substrates and Matrices; Alternating-Composition Layered Ceramic Barrier Coatings; Variable-Structure Control of a Model Glider Airplane; Axial Halbach Magnetic Bearings; Compact, Non-Pneumatic Rock-Powder Samplers; Biochips Containing Arrays of Carbon-Nanotube Electrodes; Nb(x)Ti(1-x)N Superconducting-Nanowire Single-Photon Detectors; Neon as a Buffer Gas for a Mercury-Ion Clock; Miniature Incandescent Lamps as Fiber-Optic Light Sources; Bidirectional Pressure-Regulator System; and Prism Window for Optical Alignment. Single-Grid-Pair Fourier Telescope for Imaging in Hard-X Rays and gamma Rays Range-Gated Metrology with Compact Optical Head Lossless, Multi-Spectral Data Compressor for Improved Compression for Pushbroom-Typetruments.

Source record↗
NASA NTRS2016

Tool for Generation of MAC/GMC Representative Unit Cell for CMC/PMC Analysis

This document describes a recently developed analysis tool that enhances the resident capabilities of the Micromechanics Analysis Code with the Generalized Method of Cells (MAC/GMC) 4.0. This tool is especially useful in analyzing ceramic matrix composites (CMCs), where higher fidelity with improved accuracy of local response is needed. The tool, however, can be used for analyzing polymer matrix composites (PMCs) as well. MAC/GMC 4.0 is a composite material and laminate analysis software developed at NASA Glenn Research Center. The software package has been built around the concept of the generalized method of cells (GMC). The computer code is developed with a user friendly framework, along with a library of local inelastic, damage, and failure models. Further, application of simulated thermomechanical loading, generation of output results, and selection of architectures to represent the composite material have been automated to increase the user friendliness, as well as to make it more robust in terms of input preparation and code execution. Finally, classical lamination theory has been implemented within the software, wherein GMC is used to model the composite material response of each ply. Thus, the full range of GMC composite material capabilities is available for analysis of arbitrary laminate configurations as well. The primary focus of the current effort is to provide a graphical user interface (GUI) capability that generates a number of different user-defined repeating unit cells (RUCs). In addition, the code has provisions for generation of a MAC/GMC-compatible input text file that can be merged with any MAC/GMC input file tailored to analyze composite materials. Although the primary intention was to address the three different constituents and phases that are usually present in CMCs-namely, fibers, matrix, and interphase-it can be easily modified to address two-phase polymer matrix composite (PMC) materials where an interphase is absent. Currently, the tool capability includes generation of RUCs for square packing, hexagonal packing, and random fiber packing as well as RUCs based on actual composite micrographs. All these options have the fibers modeled as having a circular cross-sectional area. In addition, a simplified version of RUC is provided where the fibers are treated as having a square cross section and are distributed randomly. This RUC facilitates a speedy analysis using the higher fidelity version of GMC known as HFGMC. The first four mentioned options above support uniform subcell discretization. The last one has variable subcell sizes due to the primary intention of keeping the RUC size to a minimum to gain the speed ups using the higher fidelity version of MAC. The code is implemented within the MATLAB (The Mathworks, Inc., Natick, MA) developmental framework; however, a standalone application that does not need a priori MATLAB installation is also created with the aid of the MATLAB compiler.

Materials Engineering↗