SEARCH · Search NASA

Results for “Adverse pressure gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1995

An experimental study of a turbulent boundary layer in the trailing edge region of a circulation-control airfoil

This report describes the development of a new near-wall LDV technique and its use to measure the full turbulent stress tensor in a highly three-dimensional separated boundary layer flow. Laser Doppler velocimetry, with small diameter laser beams allowing small beam-crossing angles (i.e., larger fringe spacings), was used, resulting in measurements close to solid surfaces. Dennis Johnson of NASA/Ames combined the advantages offered by FFT signal processors with a beam-steering probe inserted in the flow to devise a new self-aligning, near-wall LDV approach capable of making direct measurements of the transverse velocity component. This new technique was applied to a 2D, zero-pressure-gradient, flat-plate boundary layer in the High Reynolds Number Pilot Channel at Ames. Accurate and repeatable measurements of U and uu to within 30 mm of the wall were obtained. Next, the near-wall LDV technique was employed in a 3D separated boundary layer flow, consisting of a 2-dimensional wall boundary layer approaching a right-angle wedge. The resulting lateral and adverse streamwise pressure gradients generated significant spanwise velocities and turbulent stresses, and a large reverse-flow region. The near-wall LDV was modified further to facilitate measurements in the 3D Wedge Flow.

Brown, Jeffrey↗

NASA NTRS1975

Design of low-speed airfoils by numerical optimization

A practical procedure for the optimum design of low-speed airfoils is demonstrated. The procedure uses an optimization program based on a gradient algorithm coupled with an aerodynamic analysis program that uses a relaxation solution of the inviscid, full-potential equation. The analysis program is valid for both incompressible and compressible flow, thereby making optimum design of high-speed, shock-free airfoils possible. Results are presented for the following three constrained optimization problems at fixed angle of attack and Mach number: (1) adverse pressure-gradient minimization, (2) pitching-moment minimization; and (3) lift maximization. All three optimization problems were studied with various aerodynamic and geometric constraints.

Hicks, R. M.↗

NASA NTRS1985

A Method for Computing the Core Flow in Three-Dimensional Leading-Edge Vortices

A theory is presented for calculating the flow in the core of a separation-induced leading-edge vortex. The method is based on matching inner and outer representations of the vortex. The inner model of the vortex is based on the quasicylindrical Navier-Stokes equations; the flow is assumed to be steady, axially symmetric, and incompressible and in addition, gradients in the radial direction are assumed to be much larger then gradients in the axial direction. The outer model is based on the three-dimensional free-vortex-sheet theory, a higher-order panel method which solves the Prandtl-Glauert equation including nonlinear boundary conditions pertinent to the concentrated vorticity representation of the leading edge vortex. The resultant flow is evaluated a posteriori for evidence of incipient vortex breakdown and the critical helix angle concept, in conjunction with an adverse longitudinal pressure gradient, is found to correlate well with the occurrence of vortex breakdown at the trailing edge of delta, arrow, and diamond wings.

Luckring, J. M.↗

NASA NTRS2003

Turbulent Plane Wakes Subjected to Successive Strains

Six direct numerical simulations of turbulent time-evolving strained plane wakes have been examined to investigate the response of a wake to successive irrotational plane strains of opposite sign. The orientation of the applied strain field has been selected so that the flow is the time-developing analogue of a spatially developing wake evolving in the presence of either a favourable or an adverse streamwise pressure gradient. The magnitude of the applied strain rate a is constant in time t until the total strain e(sup at) reaches about four. At this point, a new simulation is begun with the sign of the applied strain being reversed (the original simulation is continued as well). When the total strain is reduced back to its original value of one, yet another simulation is begun with the sign of the strain being reversed again back to its original sign. This process is done for both initially "favourable" and initially "adverse" strains, providing simulations for each of these strain types from three different initial conditions. The evolution of the wake mean velocity deficit and width is found to be very similar for all the adversely strained cases, with both measures rapidly achieving exponential growth at the rate associated with the cross-stream expansive strain e(sup at). In the "favourably" strained cases, the wake widths approach a constant and the velocity deficits ultimately decay rapidly as e(sup -2at). Although all three of these cases do exhibit the same asymptotic exponential behaviour, the time required to achieve this is longer for the cases that have been previously adversely strained (by at approx. equals 1). These simulations confirm the generality of the conclusions drawn in Rogers (2002) regarding the response of plane wakes to strain. The evolution of strained wakes is not consistent with the predictions of classical self-similar analysis; a more general equilibrium similarity solution is required to describe the results. At least for the cases considered here, the wake Reynolds number and the ratio of the turbulent kinetic energy to the square of the wake mean velocity deficit are determined nearly entirely by the total strain. For these measures the order in which the strains are applied does not matter and the changes brought about by the strain are nearly reversible. The wake mean velocity deficit and width, on the other hand, differ by about a factor of three when the total strain returns to one, depending on whether the wake was first "favourably" or "adversely" strained. The strain history is important for predicting the evolution of these quantities.

Rogers, Michael M.↗

DOE OSTI2024

A streamline coordinate analysis of a turbulent boundary layer subject to pressure gradients and curvature on the windward side of a bump

Direct numerical simulation (DNS) of a turbulent boundary layer over the Gaussian (Boeing) bump is performed. This boundary layer exhibits a series of adverse and favourable pressure gradients and convex and concave curvature effects before separating. These effects on turbulent boundary layers are characterised and compared with a lower-Reynolds-number flow over the same geometry. The momentum budgets are analysed in the streamline-aligned coordinate system upstream of the separation region. These momentum budgets allow the simplification of equations to facilitate an integral analysis. Integral-analysis-based approximations for Reynolds stresses in the inner and outer regions of the boundary layer are also formulated. The shear and wall-normal Reynolds stress profiles normalised by these approximations exhibit a better collapse compared with friction velocity and Zagarola–Smits normalisations in the strong favourable pressure gradient region and in the mild adverse pressure region that precedes it in this flow. Simplification of these Reynolds stress approximations along with results from the DNS are used to obtain semi-empirical approximations that are able to provide stress closure in terms of wall solution fields for the turbulent boundary layer under consideration.

42 ENGINEERING↗

NASA NTRS2019

Nonlinear Görtler Vortices and Their Secondary Instability in a Hypersonic Boundary Layer

Nonlinear development of the Görtler instability over a concave surface gives rise to a highly distorted inflectional flow field in the boundary layer that leads to both wall-normal and spanwise gradients in the flow. Such nonlinear structures are susceptible to strong, high-frequency secondary instabilities that may lead to the onset of laminar-turbulent transition. The present numerical study uses direct numerical simulations and linear secondary instability theory to investigate finite amplitude Görtler vortices and their secondary instability characteristics, respectively, in the hypersonic flow over an axisymmetric cone with a concave aft body. To complement previous studies in the literature wherein the Görtler instability was usually studied for a flat plate and initiated at some upstream location by imposing an eigenfunction as the inflow condition or by blowing and suction at the wall, the present investigation is focused on fully realizable Görtler instability that is excited by an azimuthally periodic array of surface protuberances. Furthermore, while the previous work had mostly focused on the secondary instability of Görtler vortices with cross-plane velocity contours that resembled bell-shaped structures, the present results confirm that fully developed mushroom structures also exist in the hypersonic regime when the Görtler vortex amplitude is sufficiently large. Computations further reveal that the dominant modes of secondary instability in these mushroom-shaped structures correspond to an antisymmetic (i.e., sinuous) “stem” mode that concentrates within the strong, nearly wall-normal internal shear layers surrounding the stem regions underneath the caps of the mushroom structures. Additionally, there exist a multitude of other significantly unstable secondary instability modes of both symmetric and antisymmetric types. Analogous to the secondary instability of crossflow vortices in hypersonic flows, secondary instability modes of both symmetric and antisymmetric types. Analogous to the secondary instability of crossflow vortices in hypersonic flows, secondary instability modes originating from the Mack mode instability play an important role during the nonlinear breakdown process.

Laminar turbulent transition↗

NASA NTRS1978

Interaction between step fuel injectors on opposite walls in a supersonic combustor model

Results are presented from an experimental investigation of perpendicular, hydrogen fuel injection and combustion from opposing walls in a scramjet combustor model using a longitudinally staged laterally inline step-injection configuration. The model represents a portion of the flow in the Langley integrated modular scramjet engine combustor operating at a flight Mach number of 7. When operating at a ratio of jet pressure to free-stream dynamic pressure of 3, the injectors produce a bulk equivalence ratio of unity. This investigation represents part of a continuing study of the modular engine fuel injectors and is specifically designed to eliminate the adverse lateral pressure gradient observed at the injector location in a previous test. Flow survey contours at three axial locations, ranging from one-third of the engine combustor length to the total engine combustor length, are used to determine mixing efficiency and fuel distribution. Wall static pressures are analyzed by using one-dimensional theory to determine the combustion efficiency. Results show a significant improvement over previous injector designs tested in this duct geometry.

Mcclinton, C. R.↗

NASA NTRS1982

Stability of flow over axisymmetric bodies with porous suction strips

Linear triple deck, closed form solutions for mean-flow quantities are developed for axisymmetric incompressible flow past a body with porous strips. The solutions account for upstream influence and are linear superpositions of the flow past the body without suction plus the perturbations due to the suction strips. Flow past the suctionless body is calculated using the Transition Analysis Program System, and a simple linear optimization scheme to determine number, spacing, and mass flow rate through the strips on an axisymmetric body is developed using the linear, triple-deck, closed-form solutions. The theory is demonstrated by predicting optimal strip distributions, and the effect of various adverse pressure-gradient situations on stability is studied.

Nayfeh, A. H.↗

NASA NTRS1990

Improvements to a nonequilibrium algebraic turbulence model

It has been noted that while the nonequilibrium turbulence model of Johnson and King (1985, 1987) performed significantly better than alternative methods, differences between predicted and observed shock locations for certain weak interactions are produced due to a defficiency in the model's inner eddy viscosity formulation. A novel formulation for the model is presented which removes this deficiency, while satisfying the law of the wall for adverse pressure-gradient conditions better than either the original formulation or mixing-length theory.

Johnson, D. A.↗

NASA NTRS1992

Influence of freestream values on k-omega turbulence model predictions

The Wilcox (1988, 1991) k-omega model for eddy-viscosity turbulence does not require damping functions in the viscous sublayer, and its equations are less stiff near the wall. It has been designed to predict the requisite wake length in equilibrium, adverse pressure-gradient boundary-layer flows. When applied to free shear layers, however, a strong dependency of its results on the freestream value of omega has been noted. This feature is presently investigated via the self-similar equations for incompressible equilibrium boundary layers.

Menter, F. R.↗

NASA NTRS1993

Measurements Of Turbulence In Boundary-Layer Flows

Report describes experimental study of turbulence in two boundary-layer flows with adverse gradients of pressure. Flows produced about cylinder oriented with axis along that of low-speed wind tunnel of rectangular cross section. Fluctuations of velocities analyzed with respect to various mathematical models of turbulence.

Driver, David M.↗

NASA NTRS1992

Flow prediction over a transport multi-element high-lift system and comparison with flight measurements

Accurate prediction of surface-pressure distributions, merging boundary-layers, and separated-flow regions over multi-element high-lift airfoils is required to design advanced high-lift systems for efficient subsonic transport aircraft. The availability of detailed measurements of pressure distributions and both averaged and time-dependent boundary-layer flow parameters at flight Reynolds numbers is critical to evaluate computational methods and to model the turbulence structure for closure of the flow equations. Several detailed wind-tunnel measurements at subscale Reynolds numbers were conducted to obtain detailed flow information including the Reynolds-stress component. As part of a subsonic-transport high-lift research program, flight experiments are conducted using the NASA-Langley B737-100 research aircraft to obtain detailed flow characteristics for support of computational and wind-tunnel efforts. Planned flight measurements include pressure distributions at several spanwise locations, boundary-layer transition and separation locations, surface skin friction, as well as boundary-layer profiles and Reynolds stresses in adverse pressure-gradient flow.

Vijgen, P. M. H. W.↗

NASA NTRS1991

A general approach for the prediction of localized instability generation in boundary layer flows

The present approach to the prediction of instability generation that is due to the interaction of freestream disturbances with regions of subscale variations in surface boundary conditions can account for the finite Reynolds number effects, while furnishing a framework for the study of receptivity in compressible flow and in 3D boundary layers. The approach is illustrated for the case of Tollmien-Schlichting wave generation in a Blasius boundary layer, due to the interaction of a freestream acoustic wave with a localized wall inhomogeneity. Results are presented for the generation of viscous and inviscid instabilities in adverse pressure-gradient boundary layers, supersonic boundary layer instabilities, and cross-flow vortex instabilities.

Choudhari, Meelan↗

NASA NTRS1996

Comparative Study Of Four Models Of Turbulence

Report presents comparative study of four popular eddy-viscosity models of turbulence. Computations reported for three different adverse pressure-gradient flowfields. Detailed comparison of numerical results and experimental data given. Following models tested: Baldwin-Lomax, Johnson-King, Baldwin-Barth, and Wilcox.

Menter, Florian R.↗

NASA NTRS2020

Streak Instability Analysis for BOLT Configuration

The BOLT configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. A numerical study of the boundary layer instabilities over this configuration has been performed with the goal of applying state-of-the-art tools in multidimensional stability analysis that complement the other ongoing research related to the BOLT flight campaign. Specifically, the paper outlines modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane of a 1/3 rd scale BOLT configuration that was tested in the low-disturbance hypersonic wind tunnel at Purdue University and both quiet and conventional tunnels at Texas A&M University (TAMU). The basic state computations agree well with the heat flux measurements in the Purdue quiet tunnel as well as with the off-body velocity field described in a previous DNS study at the University of Minnesota. The encouraging agreement between the predicted frequency spectra of the streak instability in the region of increased boundary layer thickness and the surface pressure spectra measured during the TAMU experiments suggests that these streak instabilities may play an important role during the transition process near the symmetry plane. The modest value of the predicted peak N-factor (N max ≈ 5) for the streak instabilities provides a potential explanation for why transition is not observed under quiet flow conditions, but may occur in a noisy wind tunnel. Similar instability analyses are performed for the flight configuration at two selected flow conditions from the ascent portion of the planned flight trajectory. The predicted values of the peak N-factor suggest that transition onset in the vicinity of the center plane is possible at the ascent time of t = 26.98 seconds (N max ≈ 12.5 at X/L = 0.77), but the streak instabilities weaken sufficiently at the later time of t = 28.88 seconds (N max ≈ 11.5 at X/L ≈ 1.00) and are less likely to cause transition at that time.

Laminar turbulent transition↗

NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration

Boundary layer transition↗

NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration

The complex boundary layer flow over the BOLT flight configuration is known to exhibit multiple and potentially interacting instability mechanisms. This paper represents a continuation of our numerical investigation of the flow instabilities over the main test surface of the BOLT configuration by using state-of-the-art tools in multidimensional instability analysis. Specifically, the paper extends our previous computations by considering the separate effects of a nonzero angle of attack and a nonzero yaw on the modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane, specifically near both ends of the azimuthal region of a thick boundary layer in the middle, where this region rapidly changes to a thinner boundary layer on either side. At the t = 28.8767 s condition from the ascent part of the anticipated flight trajectory with a flight Mach number of M ∞ = 5.53 and unit Reynolds number of 4.25 x 10 6 /m, either type of departure from the design condition is shown to have a considerable impact on the structure of the basic state rollup within the region of interest and, hence, also on the amplification characteristics of instability waves within the resulting streaks. Yet, for a yaw angle of β = 4 degrees, the computations indicate only a slight reduction with respect to the peak N-factor of nearly 11 at the design condition of zero degrees yaw and zero degrees angle of attack. In contrast, an angle of attack equal to α = 4 degrees, the peak N-factor decreases to nearly 6 on the leeward side and increases above 16 on the windward side, making the onset of transition highly likely on the windward side. Computations also highlight the role of streak instabilities that originate as Mack mode disturbances and also demonstrate the potential pitfalls in using surface pressure sensors alone to gauge the magnitude of instability amplification.

Boundary layer transition↗

NASA NTRS2021

Wake Instability Behind Isolated Trip Near the Leading Edge of the BOLT-II Configuration

The BOLT-II (Holden Mission) configuration is an extended version of the BOLT flight article and depicts hypersonic boundary-layer transition in the presence of multiple and potentially interacting instability mechanisms. Several numerical studies of the boundary-layer instabilities over these configurations have been reported in the recent literature, including our previous studies of the modal instability characteristics of boundary-layer streaks adjacent to the minor-axis symmetry plane of the BOLT configuration and the wake instabilities behind a diamond planform (“pizza-box”) trip along the symmetry plane on the secondary side of the BOLT-II configuration. The present work extends the latter study to a scaled version of the same trip that is located in the region of nonzero crossflow in the vicinity of the leading edge at X/L = 0.5. Collectively, the trips along the symmetry plane and near the leading edge are the focus of the NASA roughness experiment on the secondary side of the BOLT-II configuration. The laminar basic state computation at the nominal flight design condition of Re ∞ = 5.44 x 10 6 /m and Re ∞ = 2.5 x 10 6 /m shows that the leading-edge trip with k/δ ≈ 0.70 and planform-side-length-to-height ratio of b/k = 3.0 induces multiple asymmetric, longitudinal streaks within the trip wake. The most prominent streak among these resembles a finite amplitude crossflow vortex, and it supports the amplification of multiple families of unstable modes. The application of multi-dimensional instability analysis to the wake flow reveals that the most amplified unstable mode can achieve a peak N-factor of up to 20 by X/L = 0.80, indicating that the onset of transition is more than likely to occur within eighty percent of the model length. To the best of our knowledge, the present study represents the first analysis including nonparallel and curvature effects on hypersonic tripwake instabilities in the presence of boundary-layer crossflow over a three-dimensional configuration.

Boundary layer transition↗