Search NASA⌕ Search

SEARCH · Search NASA

Results for “Experimental Evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Step Bunch Evolution on Vicinal Faces of KDP

For in-situ studies of the formation and evolution of step patterns in solution growth, we have assembled an experimental setup based on Michelson interferometry with the growing crystal surface as one of the reflective surfaces. The device allows data collection over a relatively large area (approximately 4 sq. mm) in situ and in real time during growth. The depth resolution is improved over traditional interferometry using phase-shifted images combining by a suitable algorithm. We achieve a depth resolution of approximately 50 Angstroms. Lateral resolution, dependent on the degree of magnification, is around 0.3 to 5 microns. The crystal chosen as a model in this work is potassium dihydrogen phosphate (KDP), the optically non-linear material widely used in frequency doubling applications. Kinetics of KDP crystallization is well studied so that KDP can serve as a benchmark for our investigations. We present quantitative results on the onset, initial stages and development of instabilities in moving step trains on vicinal crystal surfaces at varying supersaturation, flow rate, and flow direction. The kinetics data suggest that at low supersaturations, step bunching is caused by impurity retardation of the steps, while at higher supersaturations, we link the non-linearity during growth to interdependence of the velocity and density of the steps evidenced in independent experiments. The behavior on the surface is very dynamic, small bunches both merge and split from larger bunches as they travel across the facet. We present evidence that despite these dynamics, under steady conditions there exists a limiting value to step bunch height. This height is reached at distances between 600 and 1000 microns from the step source. In our experiments, we observed the retention of this step bunch height limit up to the path of 1500 microns.

Booth, N. A.↗
NASA NTRS2003

Intrinsic Hardware Evolution for the Design and Reconfiguration of Analog Speed Controllers for a DC Motor

Evolvable hardware provides the capability to evolve analog circuits to produce amplifier and filter functions. Conventional analog controller designs employ these same functions. Analog controllers for the control of the shaft speed of a DC motor are evolved on an evolvable hardware platform utilizing a second generation Field Programmable Transistor Array (FPTA2). The performance of an evolved controller is compared to that of a conventional proportional-integral (PI) controller. It is shown that hardware evolution is able to create a compact design that provides good performance, while using considerably less functional electronic components than the conventional design. Additionally, the use of hardware evolution to provide fault tolerance by reconfiguring the design is explored. Experimental results are presented showing that significant recovery of capability can be made in the face of damaging induced faults.

Gwaltney, David A.↗
NASA NTRS2008

Geostationary Lightning Mapper for GOES-R and Beyond

The Geostationary Lightning Mapper (GLM) is a single channel, near-IR imager/optical transient event detector, used to detect, locate and measure total lightning activity over the full-disk as part of a 3-axis stabilized, geostationary weather satellite system. The next generation NOAA Geostationary Operational Environmental Satellite (GOES-R) series with a planned launch readiness in December 2014 will carry a GLM that will provide continuous day and night observations of lightning from the west coast of Africa (GOES-E) to New Zealand (GOES-W) when the constellation is fUlly operational. The mission objectives for the GLM are to 1) provide continuous, full-disk lightning measurements for storm warning and nowcasting, 2) provide early warning of tornadic activity, and 3) accumulate a long-term database to track decadal changes of lightning. The GLM owes its heritage to the NASA Lightning Imaging Sensor (1997-Present) and the Optical Transient Detector (1995-2000), which were developed for the Earth Observing System and have produced a combined 13 year data record of global lightning activity. Instrument formulation studies were completed in March 2007 and the implementation phase to develop a prototype model and up to four flight models will be underway in the latter part of 2007. In parallel with the instrument development, a GOES-R Risk Reduction Team and Algorithm Working Group Lightning Applications Team have begun to develop the Level 2 algorithms and applications. Proxy total lightning data from the NASA Lightning Imaging Sensor on the Tropical Rainfall Measuring Mission (TRMM) satellite and regional test beds (e.g., Lightning Mapping Arrays in North Alabama and the Washington DC Metropolitan area) are being used to develop the pre-launch algorithms and applications, and also improve our knowledge of thunderstorm initiation and evolution. Real time lightning mapping data are being provided in an experimental mode to selected National Weather Service (NWS) forecast offices in Southern and Eastern Region. This effort is designed to help improve our understanding of the application of these data in operational settings.

Goodman, Steven J.↗
NASA NTRS2010

The Geostationary Lighting Mapper (GLM) for GOES-R: A New Operational Capability to Improve Storm Forecasts and Warnings

The next generation Geostationary Operational Environmental Satellite (GOES-R) series is a follow on to the existing GOES system currently operating over the Western Hemisphere. Superior spacecraft and instrument technology will support expanded detection of environmental phenomena, resulting in more timely and accurate forecasts and warnings. Advancements over current GOES capabilities include a new capability for total lightning detection (cloud and cloud-to-ground flashes) from the Geostationary Lightning Mapper (GLM), and improved spectral (3x), spatial (4x), and temporal (5x) resolution for the Advanced Baseline Imager (ABI). The GLM, an optical transient detector and imager operating in the near-IR at 777.4 nm will map all (in-cloud and cloud-to-ground) lighting flashes continuously day and night with near-uniform spatial resolution of 8 km with a product refresh rate of less than 20 sec over the Americas and adjacent oceanic regions, from the west coast of Africa (GOES-E) to New Zealand (GOES-W) when the constellation is fully operational. This will aid in forecasting severe storms and tornado activity, and convective weather impacts on aviation safety and efficiency. In parallel with the instrument development (a prototype and 4 flight models), a GOES-R Risk Reduction Team and Algorithm Working Group Lightning Applications Team have begun to develop the Level 2 algorithms and applications. Proxy total lightning data from the NASA Lightning Imaging Sensor on the Tropical Rainfall Measuring Mission (TRMM) satellite and regional test beds are being used to develop the pre-launch algorithms and applications, and also improve our knowledge of thunderstorm initiation and evolution. Real time lightning mapping data are being provided in an experimental mode to selected National Weather Service (NWS) national centers and forecast offices via the GOES-R Proving Ground to help improve our understanding of the application of these data in operational settings and facilitate Day-1 user readiness for this new capability.

Goodman, Steven J.↗
NASA NTRS2015

Modeling of Non-Isothermal Cryogenic Fluid Sloshing

A computational fluid dynamic model was used to simulate the thermal destratification in an upright self-pressurized cryostat approximately half-filled with liquid nitrogen and subjected to forced sinusoidal lateral shaking. A full three-dimensional computational grid was used to model the tank dynamics, fluid flow and thermodynamics using the ANSYS Fluent code. A non-inertial grid was used which required the addition of momentum and energy source terms to account for the inertial forces, energy transfer and wall reaction forces produced by the shaken tank. The kinetics-based Schrage mass transfer model provided the interfacial mass transfer due to evaporation and condensation at the sloshing interface. The dynamic behavior of the sloshing interface, its amplitude and transition to different wave modes, provided insight into the fluid process at the interface. The tank pressure evolution and temperature profiles compared relatively well with the shaken cryostat experimental test data provided by the Centre National D'Etudes Spatiales.

Cryogenics↗
NASA NTRSDate not supplied

Multi-Anvil Experimentation Applied to Planetary Differentiation

Planets undergo differentiation that includes segregation of metal from silicate at high temperatures and pressures ranging from deep planetary core pressures (>300 GPa for Earth)to very shallow conditions of asteroids (<100 MPa).The multi-anvil solid media apparatus accesses the middle part of this range from 3 to 30 GPa –pressure relevant to the interior of Mercury, Venus, Earth, Earth’s Moon, and Mars. Early planets are thought to have experienced high temperatures from a combination of heat sources including radioactive decay, gravitational and accretional heating, and impact processes. These heating events led to melting of mantles and cores, thus requiring an understanding of solid-liquid equilibria in metal-silicate systems. In 2006 we established a multi-anvil facility at NASA-JSC combining an 880 ton press and a Kawai/Walker type module from Rockland Research. Our high PT work has been greatly facilitated by use of the COMPRES multi-anvil assemblies (1). Our recent work has included studies of element partitioning between liquid metal and liquid silicate(e.g., 2), as well as between minerals and melts(e.g., 3), both of which have led to better constraints on the timing and conditions of planetary differentiation(e.g. 4). Several examples involving sustained efforts will be summarized below and for the presentation. The distribution of siderophile (iron-loving) elements between core and mantle is controlled by metal-silicate equilibrium across a wide range of pressures. Therefore, experimentation across this pressure range helps to calibrate elemental partitioning models that can be applied to planets, and used to predict mantle chemistry and composition during planetary differentiation. Our studies have focused on a wide range of siderophile elements (refractory Ni, Co, W, Mo; volatile P, Ga, Cu, Sn, Sb; highly siderophile Au, Pd) that have constrained partitioning, valence, and isotopic fractionation, and applied to Earth, Moon, and Mars. When molten mantles (magma oceans) cool enough to initiate crystallization, the solids precipitate at depth and in large planets this involves high pressure phases like garnet, majorite, akimotoite, and ringwoodite. As these solids precipitate they can segregate from liquid by density contrasts, thus causing elemental fractionation which can be used to decipher timing of differentiation. Mineral/melt and metal/silicate equilibria in our lab have helped to better understand high pressure fractionation of isotopic parent/daughter pairs Hf/W, Mn/Cr, Pd/Ag, Pt/Os, Re/Os, and U/Pb, and their application to Earth, Moon and Mars. There remains great potential for multi-anvil experimentation to shed light on many pressure–dependent aspects of planetary evolution such as core formation, high pressure phase equilibria, redox equilibria, and volatile evolution and storage. References1. Leinenweber, K., et al.(2012) American Mineralogist,97, 353–368. 2.Righter, K., et al.(2020) Geochem. Persp. Lett.15, 1-6.3. Righter, K., et al.(2020) Met. Planet. Sci 55, 2741-2757.4. Righter, K., et al.(2020)Earth and Planetary Science Letters,552, 116590.

pressure↗
NASA NTRSDate not supplied

Silicon Partitioning Between Iron-Rich Metal and Silicate Melt: New Constraints From Aerodynamic Laser Levitation Furnace Experiments

The partitioning of light elements (e.g., Si, C, H, etc.) between silicate melts and iron metal alloys as a function of pressure and temperature is a critical constraint in defining the compositional evolution of planetary interiors. While there are a significant number of experimental studies in the literature that examine the various influences of oxygen fugacity, temperature, pressure, and composition on the metal-melt partitioning of silicon, it is difficult to disentangle the effects of each variable due to the nominally independent parameters (e.g., pressure, temperature, composition) being collinear. To better test for the independent effects of pressure, temperature, and melt composition on the partitioning of silicon between iron alloy and silicate melt, new high temperature (1800°–2500°C), rapid quench (~700°C/s) aerodynamic levitation laser-heating experiments in the Fe-Si-Mg-O (En65-Fa5-Si3-Fe27) system were conducted. This high temperature, low pressure method is ideal for these experiments because it eliminates the metal container as a sink for elements of interest to partition into, and it has a rapid quench rate that minimizes potential exsolution of silicon from the metal phase during quench cooling. Given the short run times of the levitation experiments (30–60 seconds), a time series at a lower temperature (1700°C) in a vertical gas-mixing muffle tube furnace was also conducted to assess equilibrium times of the bulk composition. All successful runs were imaged using back-scatter electron imaging and analyzed for phase composition using a JEOL 8530F field emission microprobe. These new data were added to a comprehensive and internally consistent data set created from published experiments, and subsequently modeled using parameters designed to minimize collinearity (e.g., optical basicity is used as a proxy for melt composition). High collinearity is found in the data set however between temperature and oxygen fugacity, precluding any model that contains both as nominally independent variables. The resulting model demonstrates a statistically significant effect of pressure, temperature, and melt composition on the partitioning of silicon in Fe-rich metal, which has implications for the formation of planetary cores in rocky planets and provides important constraints on potential bulk core compositions.

Metal↗
NASA NTRS1991

Volcanic aerosols: Chemistry, evolution, and effects

Stratospheric aerosols have been the subject of scientific speculation since the 1880s, when the powerful eruption of Krakatoa attracted worldwide attention to the upper atmosphere through spectacular optical displays. The presence of a permanent tenuous dust layer in the lower stratosphere was postulated in the 1920s following studies of the twilight glow. Junge collected the first samples of these 'dust' particles and demonstrated that they were actually composed of sulfates, most likely concentrated sulfuric acid (Junge and Manson, 1961; Junge, 1963). Subsequent research has been spurred by the realization that stratospheric particles can influence the surface climate of earth through their effects on atmospheric radiation. Such aerosols can also influence, through chemical and physical effects, the trace composition of the atmosphere, ozone concentrations, and atmospheric electrical properties. The properties of stratospheric aerosols (both the background particles and those enhanced by volcanic eruptions) were measured in situ by balloon ascents and high altitude aircraft sorties. The aerosols were also observed remotely from the ground and from satellites using both active (lidar) and passive (solar occultation) techniques (remote sensing instruments were carried on aircraft and balloon platforms as well). In connection with the experimental work, models were developed to test theories of particle formation and evolution, to guide measurement strategies, to provide a means of connecting laboratory and field data, and to apply the knowledge gained to answer practical questions about global changes in climate, depletion of the ozone layer, and related environmental problems.

Turco, Richard↗
DOE OSTI2025

Status and prospects of Muon g-2 experiment

This article reviews the muon g-2 experiment, a cornerstone in precision tests of the Standard Model of particle physics. The experiment measures the anomalous magnetic moment of the muon with unprecedented accuracy, seeking potential discrepancies between theoretical predictions and experimental results that might indicate physics beyond the Standard Model. We trace the evolution of this measurement from its beginnings at CERN in the 1960s to the current state-of-the-art experiment at Fermilab, highlighting the remarkable engineering achievements required to achieve parts-per-billion precision. Recent results from Runs 1-3 have achieved a systematic uncertainty of 70 ppb, exceeding design goals, while ongoing theoretical calculations continue to refine predictions. Despite these advances, the analysis remains statistics-limited, with continued data collection and novel experimental approaches at MUonE and J-PARC promising further insights into this fundamental physical quantity.

Karuza, Marin [INFN, Trieste; Rijeka U.] (ORCID:00↗
DOE OSTI2025

HPC for Optimizing Process Parameters to Control Material Evolution in Seamless Induction Hardening of Wind Turbine Main Shaft Bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Time evolution of a pumped molecular magnet—A time-resolved inelastic neutron scattering study

Introducing an experimental technique of time-resolved inelastic neutron scattering (TRINS), we explore the time-dependent effects of resonant pulsed microwaves on the molecular magnet Cr 8 F 8 Piv 16 . The octagonal rings of magnetic Cr 3+ atoms with antiferromagnetic interactions form a singlet ground state with a weakly split triplet of excitations at 0.8 meV. A 4.6 tesla field was applied to tune the splitting between two members of the triplet excited level |1$\rangle$ ↔ |2$\rangle$ to resonance with 105 GHz (0.434 meV) microwaves. The time-dependent occupations of the ground state |0$\rangle$, lower lying levels |1$\rangle$ and |2$\rangle$, and higher energy states |λ ≥ 3$\rangle$ were extracted during and after 20 s long microwave pulses incident along the (101) direction of a Cr 8 F 8 Piv 16 crystal held at 1.9 K. At significantly elevated spin temperatures, we found underpopulation relative to thermal equilibrium of |2$\rangle$ and spin-lattice thermalization time scales ranging from 1.6(2) s to 5.7(2) s depending on the power level. This contrasts with the relaxation time τ 1 (T → 0) = 27(5) 𝛍 s inferred for |2$\rangle$ from in situ Electron Spin Resonance measurements. By probing a broad range of excited states during intense microwave pumping, TRINS thus provides a first view of long lived excited states in a molecular antiferromagnet.

Science & Technology - Other Topics↗
DOE OSTI2024

Single-Shot Diagnosis of Electron Energy Evolution via Streaked Betatron X Rays in a Curved Laser Wakefield Accelerator

We report on an experimental observation of the streaking of betatron x rays in a curved laser wakefield accelerator. The streaking of the betatron x rays was realized by launching a laser pulse into a plasma with a transverse density gradient. By controlling the plasma density and the density gradient, we realized the steering of the laser driver, electron beam, and betatron x rays simultaneously. Furthermore, we observed an energy-angle correlation of the streaked betatron x rays and utilized it in diagnosing the electron acceleration process in a single-shot mode. Our work could also find applications in advanced control of laser beam and particle propagation. More importantly, the angular streaked betatron x ray has an intrinsic spatiotemporal correlation, which makes it a promising tool for single-shot pump-probe applications.

43 PARTICLE ACCELERATORS↗
NASA NTRS1986

Carbon dioxide evolution rate as a method to monitor and control an aerobic biological waste treatment system

An experimental system was developed to study the microbial growth kinetic of an undefined mixed culture in an erobic biological waste treatment process. The experimental results were used to develop a mathematical model that can predict the performance of a bioreactor. The bioreactor will be used to regeneratively treat waste material which is expected to be generated during a long term manned space mission. Since the presence of insoluble particles in the chemically undefined complex media made estimating biomass very difficult in the real system, a clean system was devised to study the microbial growth from the soluble substrate.

Lee, S. S.↗
DOE OSTI2025

Structure evolution and tin redistribution during oxidation of Zircaloy-4 at 500°C

Zirconium (Zr) alloys are widely used as fuel cladding in nuclear power reactors due to their thermal stability, mechanical durability, corrosion resistance, and low neutron absorption cross-section. However, their performance is challenged by oxidation in reactor environments, making the study of Zr alloy corrosion behavior crucial for ensuring the safety, longevity, and economic viability of nuclear power systems. While the oxidation behavior of Zr-based cladding materials has been extensively studied since the 1950s, a mechanistic understanding into the relationship between structure evolution, solute element redistribution, and properties remains elusive. Valuable insights may be obtained through advanced experimental methods, such as in-situ and high resolution microscopy techniques. Here, in this study, the oxidation behavior of Zircaloy-4 at 500 °C in O 2 is characterized using a multimodal advanced characterization approach. Using in-situ X-ray diffraction, the phase evolution from metastable to stable oxides is tracked in real time. Complementary high-resolution techniques, including electron microscopy and atom probe tomography, reveal nanoscale insights into the microstructural changes and solute redistribution across the oxide/metal interface. Nanohardness mapping across the oxide/metal interface highlights localized mechanical property variations that may be linked to changes in microstructure and crystal structure within the oxide layer. These findings offer valuable insights into the microstructure and property evolution of Zircaloy-4 during oxidation, contributing to a better understanding of microstructural changes in Zr-based alloys under oxidative environments.

APT↗
NASA NTRS2005

The Origin and Early Evolution of Membrane Proteins

Membrane proteins mediate functions that are essential to all cells. These functions include transport of ions, nutrients and waste products across cell walls, capture of energy and its transduction into the form usable in chemical reactions, transmission of environmental signals to the interior of the cell, cellular growth and cell volume regulation. In the absence of membrane proteins, ancestors of cell (protocells), would have had only very limited capabilities to communicate with their environment. Thus, it is not surprising that membrane proteins are quite common even in simplest prokaryotic cells. Considering that contemporary membrane channels are large and complex, both structurally and functionally, a question arises how their presumably much simpler ancestors could have emerged, perform functions and diversify in early protobiological evolution. Remarkably, despite their overall complexity, structural motifs in membrane proteins are quite simple, with a-helices being most common. This suggests that these proteins might have evolved from simple building blocks. To explain how these blocks could have organized into functional structures, we performed large-scale, accurate computer simulations of folding peptides at a water-membrane interface, their insertion into the membrane, self-assembly into higher-order structures and function. The results of these simulations, combined with analysis of structural and functional experimental data led to the first integrated view of the origin and early evolution of membrane proteins.

Pohorille, Andrew↗
DOE OSTI2024

Velocity Dependence of Rate‐And‐State Friction in Granular Fault Gouge and Implications for Slow‐Slip Events

Abstract The standard rate‐and‐state friction (RSF) has extensively captured frictional behaviors, but it fails to explain the velocity dependence of frictional stability transition and widespread slow‐slip events (SSEs) in experiments and nature adequately. An alternative microphysical Chen‐Niemeijer‐Spiers (CNS) model can well describe the velocity dependence of frictional behaviors of granular gouges. Using the original CNS model, standard RSF parameters can be quantified microphysically. However, some micro‐parameters are not easy to estimate quantitatively, making it difficult to extrapolate to natural and experimental conditions. Here, we simplify the microphysically‐derived RSF parameters including direct effect a , evolution effect b , and critical slip distance D c , as well as equivalent values ( a eq , b eq , and D eq ). The simplified friction parameters directly illustrate their velocity dependence, namely the essentially constant a , a eq , and D c , negatively velocity‐dependent b and b eq , as well as varying D eq for different laws. They are roughly consistent with experimental results in various fault gouges. A modified CNS model is further derived from the original CNS model, establishing a direct link between the standard RSF and CNS models. The modified CNS model exhibits virtually identical frictional behaviors to the original CNS, but differs from the standard RSF at large velocity perturbations. Moreover, the linearized stability analysis indicates that the critical stiffness for the modified CNS model is velocity‐dependent. Compared with the standard RSF, the modified CNS model not only explains the velocity dependence of frictional stability transition, but also exhibits a more gradual transition for SSEs with a broader range of stiffness ratios.

Geochemistry & Geophysics↗
DOE OSTI2025

HPC for optimizing process parameters to control material evolution in seamless induction hardening of wind turbine main shaft bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

17 WIND ENERGY↗
NASA NTRS1982

The dryout region in frictionally heated sliding contacts

Some conditions under which boiling and two-phase flow can occur in or near a wet sliding contact are determined and illustrated. The experimental apparatus consisted of a tool pressed against an instrumented slider plate and motion picture sequences at 4000 frames/sec. The temperature and photographic data demonstrated surface conditions of boiling, drying, trapped gas evolution (solutions), and volatility of fluid mixture components. The theoretical modeling and analysis are in reasonable agreement with experimental data.

Hendricks, R. C.↗