Search NASA⌕ Search

SEARCH · Search NASA

Results for “LED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The lipidomics reporting checklist a framework for transparency of lipidomic experiments and repurposing resource data

The rapid increase in lipidomic studies has led to a collaborative effort within the community to establish standards and criteria for producing, documenting, and disseminating data. Creating a dynamic checklist that condenses key information about lipidomic experiments into common terminology will enhance the field's consistency, comparability, and repeatability. Here, we describe the structure and rationale of the established Lipidomics Minimal Reporting Checklist to increase transparency in lipidomics research.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Integrated process-structure–property–performance optimization of cold-sprayed zinc coatings on AZ91 magnesium alloy

High-pressure die cast (HPDC) AZ91 magnesium alloy is widely used in automotive components such as transmission housings and brackets for its excellent strength-to-weight ratio. Zinc-based cold spray coatings can be applied selectively to vulnerable areas to enhance corrosion resistance, minimize galvanic coupling with dissimilar metals, and eliminate the need for full-surface oxide coatings, making the process more efficient and targeted. A comprehensive evaluation of 16 combinations of nitrogen carrier gas temperatures and pressures led to the identification of an optimal range of process parameters, yielding Zn coatings with porosity <0.5 % by area, wear rates reduced by a factor of two compared to uncoated AZ91, and adhesion strengths up to 35 MPa. The enhanced mechanical performance of the coating is attributed to the low porosity and the formation of a metallurgical bond at the coating-substrate interface. Corrosion studies using macroscale potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) revealed a significant decrease in corrosion rate and a shift to more noble corrosion potentials (ZCP) for coated substrates. Furthermore, the Zn cold-sprayed samples exhibited significantly lower corrosion-induced evolved hydrogen content compared to the base AZ91 substrate and AZ91 coated with industrial coatings, demonstrating that the Zn layer effectively protects the substrate from the corrosive environment. Overall, cold spray Zn coatings significantly improve the mechanical and corrosion performance of AZ91 Mg alloys, addressing key material challenges and enabling their broader use in automotive applications.

Corrosion performance↗
DOE OSTI2025

Optimization of overhang printing in ceramic binder jetting additive manufacturing

Cylindrical-shaped horizontally-hanging overhangs with different heights on a solid cubic body were printed via binder jetting additive manufacturing with sililcon carbide powder feedstock. Cracking on the overhang neck and sagging on the overhang body were observed both pre- and post-curing, especially on printed design with a smaller particle size of 10 μm. Here, it was found that the width of cracking and depth of sagging were dependent on the height relative to the solid body in the powder bed, and elevated position of overhang with large volume of underneath loose powder led to increased extend of cracking and sagging. Overhang diameter and weight were varied, which were found with no apparent effects on its deformation extend. To mitigate cracking and sagging, contactless support was designed and tested, which could significantly improve the overhang stability and avoid any overhang deformations. Support gap and support distance were studied for their effects on support capability. The printing processes with and without contactless support were simulated by a finite element modeling approach to understand the stress distribution and evolution of the overhang structures, which revealed stress concentrations on the upper neck point of the designed overhang.

Binder jetting↗
DOE OSTI2024

Multinuclear PFGSTE NMR description of 39 K, 23 Na, 7 Li, and 1 H specific activation energies governing diffusion in alkali nitrite solutions

While pulsed field gradient stimulated echo nuclear magnetic resonance (PFGSTE NMR) spectroscopy has found widespread use in the quantification of self-diffusivity for many NMR-active nuclei, extending this technique to uncommon nuclei with unfavorable NMR properties remains an active area of research. Potassium-39 ( 39 K) is an archetypical NMR nucleus exhibiting an unfavorable gyromagnetic ratio combined with a very low Larmor frequency. Despite these unfavorable properties, this work demonstrates that 39 K PFGSTE NMR experiments are possible in aqueous solutions of concentrated potassium nitrite. Further, analysis of the results indicates that 39 K NMR diffusometry is feasible when the nuclei exhibit spin–lattice and spin–spin relaxation coefficients on the order of 60–100 ms and 50–100 ms, respectively. The diffusivity of 39 K followed Arrhenius behavior, and comparative 23 Na, 7 Li, and 1 H PFGSTE NMR studies of equimolal sodium nitrite and lithium nitrite solutions led to correlations between the enthalpy of hydration with the activation energy governing self-diffusion of the cations and also of water. Realizing the feasibility of 39 K PFGSTE NMR spectroscopy has a widespread impact across energy sciences because potassium is a common alkali element in energy storage materials and other applications.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

Effects of Zn and Ca on the deformation texture evolution of Mg–Zn–Ca alloys at elevated temperatures

This work utilized crystal plasticity simulations and experimental thermo-mechanical processing to examine how Zn and Ca content affects texture evolution in Mg–Zn–Ca alloys during simulated hot rolling. Four different compositions were studied: unalloyed Mg and three Mg alloys of ZX0p50 (Mg- 0.5 wt% Zn- 0.1 wt% Ca), ZX30 (Mg-3 wt% Zn- 0.1 wt% Ca), and ZX31 (Mg-3 wt% Zn- 0.3 wt% Ca). Multi-pass Gleeble experiments simulated hot rolling using plane strain conditions. Unalloyed Mg developed a strong basal texture, while the addition of Zn and Ca significantly weakened the texture in ZX30 and ZX31; this reduction was not seen in ZX0p50. Notably, ZX31 exhibited a split basal texture aligned with the rolling direction. Crystal plasticity simulations revealed that the weaker basal texture in ZX30 and ZX31 resulted from reduced activation of basal and twinning modes compared to unalloyed Mg and Zx0p50. Increased Zn and Ca content raised the ratios of basal to pyramidal critical resolved sheer stress (CRSS) and twin to pyramidal CRSS, enhancing pyramidal slip activity and weakening the basal texture. Extension twinning played a critical role in texture development during the first deformation pass. In unalloyed Mg and ZX0p50, twinning led to a strong basal texture, while ZX30 and ZX31 had weak basal textures that increased only slightly with further deformation. The split basal poles simulated in ZX31 were consistent with the experimental findings, highlighting the interplay between alloy composition and texture evolution.

Crystal plasticity finite element↗
DOE OSTI2025

Densification, microstructure, and mechanical properties of Mo–30W alloys fabricated from conditioned powders

Refractory alloys, such as molybdenum-based systems, are attracting growing interest for applications in extreme environments, such as in the nuclear and aerospace industries. Recent advances in sintering technologies, coupled with mechanical alloying, have enabled the tailored design of these alloys by leveraging powder characteristics to control final microstructures and mechanical properties. In this study, Mo-30W alloys were fabricated using electric field-assisted sintering (EFAS) from ball-milled powders with and without hydrogen treatment to investigate the influence of surface oxides on material properties and sintering behavior. The results revealed that samples processed from as-ball-milled powder contained a high density of oxides within the microstructure, whereas oxide presence was significantly reduced in samples fabricated from hydrogen-treated powders. Interestingly, the two powder types led to opposite trends in grain size distribution: samples from untreated powders exhibited grain refinement from sample periphery to the center, while samples from hydrogen-treated powders showed grain coarsening toward the center. This behavior is attributed to temperature gradients present during sintering due to electrical percolation pathway differences during Joule heating. The powder surface oxides may have influenced the temperature distribution and grain evolution. Microhardness profiles measured along both axial and thickness directions were consistent with the grain size distribution. Furthermore, oxide films on powder surfaces have delayed densification by hindering particle necking and atomic diffusion during sintering.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Effect of post-weld heat treatment on microstructure and mechanical properties of rotary inertia friction welded dissimilar 422-4140 martensitic steel piston joints

The study investigated how post‐weld heat treatment (PWHT) temperature affects the microstructure and localized deformation/fracture during bend testing of rotary inertia friction welds (RIFW) between AISI 422 stainless steel and AISI 4140 steel. RIFW produced a fully martensitic interface with approximately 550 HV hardness in both the thermo-mechanically affected (TMAZ) and heat‐affected zones (HAZ). Due to differences in temper resistance, the 4140 TMAZ/HAZ softened progressively under PWHT temperatures from 525 °C to 700 °C, while the 422 TMAZ unexpectedly maintained about 550 HV up to 600 °C before significantly softening at temperatures ≥625 °C. This asymmetric softening generated steep hardness gradients across the interface at temperatures ≤600 °C. Furthermore, carbon migration across the interface was minimal up to 600 °C, moderate at 625 °C, and by 700 °C produced a carbide‐rich eutectoid layer in the 422 TMAZ alongside a carbon‐depleted soft ferrite layer in the 4140 TMAZ. Strain during bending was PWHT‐dependent, concentrating on the 4140 side; in as-welded joints, the high hardness led to deformation and crack initiation in the base metals, whereas in PWHT samples, cracking initiated in the softened 4140 TMAZ near the interface. The intermediate PWHT temperature of 625 °C offered the best balance of limited carbon diffusion across the interface, relatively low peak weld hardness and minimized hardness gradients across the interface, more homogenous deformation, and good bend test performance.

4140 low-alloy steel↗
DOE OSTI2024

Microstructural evolution in doped high entropy alloys NiCoFeCr-3X (X=Pd/Al/Cu) under irradiation

Commonly studied equatomic single-phase FCC high entropy alloys based on 3d transition metals like NiCoFeCr do not provide adequate strength and radiation resistance at high doses for nuclear structural applications. In the current study, the major alloying effects like lattice distortion, ordering and clustering tendencies were investigated by adding low concentration of Pd, Al, or Cu respectively to study the doping effects on the ion irradiation response of NiCoFeCr alloy. The alloys were irradiated with 3 MeV Ni 2+ ions at 500 °C to a fluence of 1 × 10 17 /cm 2 at a beam flux of approximately 2.8 × 10 12 ions/cm 2 /s. The microstructural evolution upon irradiation i.e., formation of dislocation networks, radiation induced segregation and precipitation, and void formation were studied in detail. Further, post-irradiation characterization results showed that a Pd addition leads to a high void nucleation rate but controlled void growth, which may be attributed to increased lattice distortion. In Al added HEA, our microstructural analysis indicates that radiation induced ordered L1 2 precipitates do not affect void swelling significantly. Cu addition led to Cu precipitation that drastically suppressed dislocation density and void swelling of the alloy. Additionally, a model was developed to qualitatively describe the trend in void swelling of typical FCC alloys under ion irradiation. This model was able to qualitatively explain the suppression and reappearance of void swelling in ion irradiated alloys that generally occurs near the region with peak implanted ion concentration.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hot Hydrogen Exposure of U x Zr 1-x C y Nuclear Fuel: The Effect of Additional Carbon

Nuclear thermal propulsion (NTP) using hydrogen as propellant in a solid-state fission reactor to reach temperatures of up to 3000K can achieve significantly higher specific impulse than chemical propulsion. A promising fuel that is again considered for NTP is U x Zr 1-x C y . To reduce the overall mass loss as well as the uranium fuel loss, a range of experiments using additional carbon in hot hydrogen (2600 K, 6 SLPM flow rate) were performed for up to 5-6 h. Both a CH 4 addition (0.1 and 0.2 vol%) in the hydrogen stream and the use of sacrificial graphite pieces upstream of the samples were tested, with sample compositions from 5 at% UC to 30 at% UC. The results showed a strong reduction of mass loss, up to a factor of 3, as well as a reduction of surface uranium losses in the presence of additional carbon in the atmosphere. Even with additional carbon in the atmosphere, material with 30 at% UC was not stable, but material with 20 at% UC was stable for up to 6h. The sample surfaces showed texturing after processing, possibly by grain growth on the surface. This led to a separation into grains with high uranium content close to the (100)-orientation, and with low uranium content in grains close to the (111)-orientation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Energy innovation in the US buildings sector: Setting the stage and mapping the future

Jared Langevin is a staff scientist at Lawrence Berkeley National Laboratory, where he leads modeling of US buildings sector innovation and its implications for energy demand, consumer costs, and the power grid. Eric Wilson is a senior research engineer in the Building Technologies and Sciences Center at the National Renewable Energy Laboratory (NREL). Much of his 15-year career at NREL has revolved around modeling and analysis of the US building stock. Jared and Eric co-led the development of a National Blueprint for buildings sector innovation while serving as advisors to the US Department of Energy’s Deputy Assistant Secretary for Buildings and Industry.

Langevin, Jared↗
DOE OSTI2026

Microstructural stability of irradiated yttrium hydride under thermal cycles

Hydrides that retain their hydrogen in service are critical for advanced microreactor and space nuclear systems. Hydrogen retention is affected by evolving microstructure under temperature and irradiation extremes. This study investigated microstructural features in neutron-irradiated yttrium hydride and the stability of these features under thermal cycles. Differential scanning calorimetry was used to determine hydrogen desorption and temperatures at which significant phase changes are occurring, and transmission electron microscopy was used for microstructural analysis after each thermal cycle. Cyclic heating led to crystallization and epitaxial growth of surface oxidation and dehydriding of the matrix. Other features such as the bulk matrix crystal structure, irradiation-induced cavities, and matrix precipitation remained constant after thermal cycling. Results allow us to design better hydride alloys through microstructure tailoring and potential irradiation conditioning treatments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exceptional strength and wear resistance in an AA7075/TiB 2 composite fabricated via friction consolidation

The friction consolidation method successfully reinforced aluminum 7075 alloy (AA7075) with high-volume fractions (12 and 24 vol%) of titanium diboride (TiB 2 ) by high pressure and severe plastic deformation at elevated temperatures. The consolidated AMCs have a uniform dispersion of submicron- and micron-sized TiB 2 particles in the AA7075 matrix, with significant refinement of the matrix grain size and the particles. The addition of TiB 2 significantly increases hardness by up to 50 %, Young’s modulus by up to 62 %, and ultimate tensile strength by up to 28 % to 672 MPa, while reducing ductility by 80 %. Wear resistance of 7075/24 vol% TiB 2 improves seven-fold compared to baseline, making it comparable to that of carburized steels. Microstructure-based finite element modeling provided a theoretical strength limit of ~730 MPa for the composites and indicated that high triaxiality in conjunction with severe equivalent plastic strain in a narrow area between the TiB 2 particles led to early fracture initiations, limiting the ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Wetting mechanism and alteration of nano-sized shale pores: Insights from contrast variation small angle neutron scattering

Wettability of tight shale is crucial for fluid flow and mass transport process in energy geosciences. However, understanding the interfacial chemistry and wetting mechanisms at sub-nano-pore scales remains a formidable challenge. Here, in this study, the Contrast Variation technique of Small Angle Neutron Scattering (CV-SANS) is employed to investigate shale’s interfacial chemistry using reagents that possess a range of different polarities, including water, n-decane, toluene, and dimethyl methanamide. Through five different experimental strategies, we have demonstrated a successful modification of shale wettability, ranging from enhancement, weakening, to reversal. Delving into the mechanisms, we illustrated the crucial role of pre-existing liquid films in these changes, where the uniquely co-existing polar and non-polar functional groups in dimethyl methanamide acted as a conduit for interfacial chemistry adjustments. Furthermore, a solvent immersion led to matrix dilation as well as liberation of residual oil-occupied pores, resulting in altered pore size distributions, with hydrogen bonding playing a significant role in the polar groups. Interestingly, despite shale exhibiting a stronger affinity for oil over water, hydrophilic solvents induced more substantial dilation than lipophilic ones. Collectively, this work elucidates the dynamic change of interfacial chemistry via the configuration of polarity using chemical reagents, and the CV-SANS technique underscores its invaluable utilities in decoding the interfacial wettability traits in nanopore space of shale.

58 GEOSCIENCES↗
DOE OSTI2024

Probing the potential of type V Deep eutectic solvents as sustainable electrolytes

The increasing interest within the scientific community in environmentally friendly solvents has led to a focus on Deep Eutectic Solvents (DES), which have natural components. DES are viewed as alternatives to traditional organic solvents and have the potential to be used as electrolytes. For the first time, transport properties of four Type V Deep Eutectic Salt Solutions (DESS) were accessed to investigate the potential of this technology, selecting precursors ranked as excellent in Eco-Scale metrics. The DESS were composed of terpene and trioctylphosphine oxide (TOPO), and varying concentrations of lithium bis(trifluoromethane)sulfonimide (LiTFSI), and their properties were assessed through self-diffusion, viscosity, density, and conductivity measurements. While Type V DESS are capable of dissolving significant amounts of LiTFSI (up to 30 % molar), their ionic conductivity is low, with values ranging from 3.6·10 –3 to 9.3·10 –2 mS·cm –1 at 25 °C, thus limiting their suitability as electrolytes, for instance, for lithium-ions batteries applications. Similar diffusion coefficients for Li + and TFSI – ions suggest the formation of long-lived ion pairs moving as a neutral species. As a result, future research aims to introduce additives to disrupt contact ion pairs and enhance transport properties, leveraging the sustainable appeal of DES and their use in advanced energy storage technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Hydrogen embrittlement of Zircaloy-4 fabricated by ultrasonic additive manufacturing

Ultrasonic additive manufacturing (UAM) was successfully applied to the zirconium material system to create a planar geometry. Following fabrication, SS-J3 type tensile specimens of the UAM and wrought Zircaloy-4 with a nominal gage section of 5×1.2×0.75 mm were machined for hydriding studies and mechanical testing. The SS-J3 type tensile specimens were gas-charged with hydrogen using a custom system that precisely controls hydrogen gas flow rate, hydrogen partial pressure, and temperature. To avoid altering the UAM material, the maximum process temperature was limited to 550°C. Using different initial hydrogen gas pressures and flow rates, various hydrogen contents (70–1755 wppm) were achieved for Zircaloy-4 specimens. Tensile testing shows that, regardless of hydrogen content, all UAM specimens measured yield strengths in the range of 557±16 MPa and ultimate tensile strengths of 660±4MPa. However, total elongation clearly decreased as a function of increasing hydrogen content. Further, at the lowest hydrogen content, the total plastic elongation measured 21.5%, and this value decreased to less than 2% when the hydrogen content was increased to 1000 wppm. Cross-sectional optical microscopy images revealed that the hydride distributions are randomly oriented. For the low hydrogen content specimen, these randomly distributed hydrides are isolated from each other. A sandwiched structure, consisting of high-density and low-density layers, was also observed for the specimens with hydrogen content between 200 and 400 wppm. As the hydrogen content increases, the hydrides diffuse into the low-density hydride layers to form a network across the whole specimen. Although the tensile properties of UAM and wrought Zircaloy-4 exhibit the same behavior with increasing hydrogen content, the distinctions in grain orientations led to differences in the hydride orientations at low and intermediate hydrogen concentrations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Friction surface layer deposition of triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high entropy alloy: Process optimization and microstructural evolution

A high-strength Co-free triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high-entropy alloy (HEA) was successfully fabricated using Friction Surface Layer Deposition (FSLD), a bulk manufacturing method. Multiple single-layer deposits were produced by varying forging force (F) and traverse speeds (T r ) to optimize the process parameters. The optimized conditions (F = 40 kN & T r = 200 mm/min) were then applied to manufacture a scaled-up multi-layer specimen. The initial microstructure of the HEA consisted of coarse grains of the soft FCC-phase, long columnar dendrites of the hard BCC-phase, and small precipitates of the harder B2-phase within the BCC-dendrites. During FSLD, the FCC-matrix underwent continuous dynamic recrystallization due to high-temperature severe plastic deformation, forming finer equiaxed grains. Simultaneously, the BCC-dendrites fractured into smaller fragments, some of which experienced partial growth and coarsening under applied stress, resulting in an hourglass morphology. In contrast, the small B2-precipitates within the BCC-fragments dissolved during the elevated temperatures of FSLD and reprecipitated as substantially finer precipitates during continuous cooling post-FSLD. Additionally, the orientation relationships between the FCC and BCC/B2 phases were completely destroyed by the severe thermoplastic deformation inherent to FSLD. The microstructural refinements led to a substantial improvement in hardness from 177 HV to 283 HV, driven by Hall-Petch strengthening. The increased number of interfaces, including coherent BCC-B2 interfaces, potentially enhances the sink strength and radiation tolerance of the HEA, making it a promising candidate for nuclear applications. In conclusion, this study also highlights FSLD as a versatile technique for achieving tunable properties in HEAs, with detailed schematics illustrating the complex mechanisms of phase transformations during processing.

Additive Manufacturing↗
DOE OSTI2026

Microstructural evolution, defect mitigation, and precipitation behavior in AA6061 via laser powder bed fusion with high-temperature substrate heating

Defects, particularly solidification cracking, remain persistent challenges in the laser powder bed fusion (LPBF) processing of AA6061 aluminum alloy. This study systematically investigates defect mitigation, microstructural evolution, and mechanical properties associated with high-temperature substrate preheating at 500 °C. Comprehensive microstructural analyses, including characterization of defects, grain structures, and precipitation behavior, were performed on samples in both as-built and T6 heat-treated states. Elevated preheating substantially reduced solidification cracking across a wide processing window, while demonstrating decreased crack sensitivity to laser parameters. Columnar cracks along the build direction were observed despite substrate preheating. Lack-of-fusion and keyhole porosity were effectively eliminated, though gas-induced microporosity persisted at higher powers. In-depth characterization of two distinct laser power and speed conditions confirmed the formation of micron-sized, non-coherent Mg 2 Si precipitates under heated substrate conditions, alongside α-AlFeCrMnSi intermetallic phases indicative of in-situ thermal effects during fabrication. Subsequent T6 heat treatment revealed the formation of fine, coherent needle-shaped β″ strengthening precipitates. Despite substantial differences in processing parameters, comparable mechanical properties were measured in the as-built samples (∼52 MPa yield strength, ∼130 MPa tensile strength), primarily due to reduced strain hardening effects and consistent precipitation characteristics. Meanwhile, the T6 heat treatment led to significant improvement in properties, enhancing yield strength by over 400%, aligning closely with the performance of conventional wrought AA6061-T6. These findings underscore that high-temperature substrate preheating offers an effective means to suppress cracks, control precipitation, and enhance mechanical performance in LPBF-processed AA6061.

36 MATERIALS SCIENCE↗