Search NASA⌕ Search

SEARCH · Search NASA

Results for “PALLADIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Development of a hydrogen gas sensor using microfabrication technology

Microfabrication and micromachining technologies are used to produce a hydrogen gas sensor based on a palladium-silver film. The sensor uses a heater that is fabricated by diffusing p-type borones into the substrate, forming a resistance heater. A diode for temperature measurement is produced using p-type boron and n-type phosphor diffused into the substrate. A thickness of the palladium-silver film is approximately 300 arcsec. The hydrogen gas sensor employs the proven palladium-silver diode structure and is surrounded by a phosphor doped resistance heater which can be heated up to a temperature of 250 C. Experimental results show that the sensor is capable of operating over a wide range of hydrogen concentration levels between 0-95 percent without any hysteresis effects.

Liu, Chung-Chiun↗
NASA NTRS1999

Effects of Hydrogen on Tantalum Nitride Resistors

This document is a presentation about the investigation of drift reported in static frequency output from the analog circuit of a Multichannel Microwave Integrated circuit hybrid microelectronic filter module for space flight application. Electron Dispersion X-Ray Detector )EDAX) Analysis of the 35k ohm thin film Tantalum Nitride Chip resistors identified Palladium in the film. A catalytic reaction of Palladium and hydrogen produces mono atomic hydrogen. When the filter module cavities were filled with a 4 % hydrogen 96 % Nitrogen gas mixture at 25C and monitored the electrical performance for 24 hours. Some channels drifted in a similar pattern as the channel being investigated. Palladium was found on the resistors. The corrective actions taken are reviewed, which resulted in a stable circuit.

Weiler, James↗
NASA NTRS2008

Miniaturized metal (metal alloy)/ PdO.sub.x/SiC hydrogen and hydrocarbon gas sensors

A miniaturized Schottky diode hydrogen and hydrocarbon sensor and the method of making same is disclosed and claimed. The sensor comprises a catalytic metal layer, such as palladium, a silicon carbide substrate layer and a thin barrier layer in between the catalytic and substrate layers made of palladium oxide (PdO.sub.x). This highly stable device provides sensitive gas detection at temperatures ranging from at least 450 to 600.degree. C. The barrier layer prevents reactions between the catalytic metal layer and the substrate layer. Conventional semiconductor fabrication techniques are used to fabricate the small-sized sensors. The use of a thicker palladium oxide barrier layer for other semiconductor structures such as a capacitor and transistor structures is also disclosed.

Hunter, Gary W.↗
NASA NTRS2008

Miniaturized Metal (Metal Alloy)/PdO(x)/SiC Hydrogen and Hydrocarbon Gas Sensors

A miniaturized Schottky diode hydrogen and hydrocarbon sensor and the method of making same is disclosed and claimed. The sensor comprises a catalytic metal layer, such as palladium, a silicon carbide substrate layer and a thin barrier layer in between the catalytic and substrate layers made of palladium oxide (PdO(x)). This highly stable device provides sensitive gas detection at temperatures ranging from at least 450 to 600 C. The barrier layer prevents reactions between the catalytic metal layer and the substrate layer. Conventional semiconductor fabrication techniques are used to fabricate the small-sided sensors. The use of a thicker palladium oxide barrier layer for other semiconductor structures such as a capacitor and transistor structures is also disclosed.

Hunter, Gary W.↗
NASA NTRS2010

Process for Making a Noble Metal on Tin Oxide Catalyst

To produce a noble metal-on-metal oxide catalyst on an inert, high-surface-area support material (that functions as a catalyst at approximately room temperature using chloride-free reagents), for use in a carbon dioxide laser, requires two steps: First, a commercially available, inert, high-surface-area support material (silica spheres) is coated with a thin layer of metal oxide, a monolayer equivalent. Very beneficial results have been obtained using nitric acid as an oxidizing agent because it leaves no residue. It is also helpful if the spheres are first deaerated by boiling in water to allow the entire surface to be coated. A metal, such as tin, is then dissolved in the oxidizing agent/support material mixture to yield, in the case of tin, metastannic acid. Although tin has proven especially beneficial for use in a closed-cycle CO2 laser, in general any metal with two valence states, such as most transition metals and antimony, may be used. The metastannic acid will be adsorbed onto the high-surface-area spheres, coating them. Any excess oxidizing agent is then evaporated, and the resulting metastannic acid-coated spheres are dried and calcined, whereby the metastannic acid becomes tin(IV) oxide. The second step is accomplished by preparing an aqueous mixture of the tin(IV) oxide-coated spheres, and a soluble, chloride-free salt of at least one catalyst metal. The catalyst metal may be selected from the group consisting of platinum, palladium, ruthenium, gold, and rhodium, or other platinum group metals. Extremely beneficial results have been obtained using chloride-free salts of platinum, palladium, or a combination thereof, such as tetraammineplatinum (II) hydroxide ([Pt(NH3)4] (OH)2), or tetraammine palladium nitrate ([Pd(NH3)4](NO3)2).

Davis, Patricia↗
NASA NTRS2011

Miniaturized metal (metal alloy)/ PdO.sub.x/SiC hydrogen and hydrocarbon gas sensors

A miniaturized Schottky diode hydrogen and hydrocarbon sensor and the method of making same is disclosed and claimed. The sensor comprises a catalytic metal layer, such as palladium, a silicon carbide substrate layer and a thin barrier layer in between the catalytic and substrate layers made of palladium oxide (PdO.sub.x ). This highly stable device provides sensitive gas detection at temperatures ranging from at least 450 to 600.degree. C. The barrier layer prevents reactions between the catalytic metal layer and the substrate layer. Conventional semiconductor fabrication techniques are used to fabricate the small-sized sensors. The use of a thicker palladium oxide barrier layer for other semiconductor structures such as a capacitor and transistor structures is also disclosed.

Hunter, Gary W.↗
DOE OSTI2020

Mesoporous PdAg Nanospheres for Stable Electrochemical CO 2 Reduction to Formate

Palladium is a promising material for electrochemical CO 2 reduction to formate with high Faradaic efficiency near the equilibrium potential. It unfortunately suffers from problematic operation stability due to CO poisoning on surface. In this work, it is demonstrated that alloying is an effective strategy to alleviate this problem. Mesoporous PdAg nanospheres with uniform size and composition are prepared from the co-reduction of palladium and silver precursors in aqueous solution using dioctadecyldimethylammonium chloride as the structure-directing agent. The best candidate can initiate CO 2 reduction at zero overpotential and achieve high formate selectivity close to 100% and great stability even at <-0.2 V versus reversible hydrogen electrode. The high selectivity and stability are believed to result from the electronic coupling between Pd and Ag, which lowers the d-band center of Pd and thereby significantly enhances its CO tolerance, as evidenced by both electrochemical analysis and theoretical simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2026

DNA Crystals as a Template for Patterned Functional Materials

DNA nanotechnology offers a wide toolkit of molecular functionalities and scales, including intricate motifs less than 10 nm and periodic structures exceeding 100 µm. At larger scales, however, there are often significant tradeoffs for DNA structures, namely stability and mechanical strength. This work describes the design, synthesis, and characterization of a functionalized DNA crystal. Using a ligated DNA crystal grants significant freedom for various functional materials to be applied, in this case, semiconducting cadmium sulfide and palladium metal. Properties investigated in this study include stability, mechanical strength, and optoelectronic properties such as photoluminescence (PL) and electric conductivity. Significant changes are observed based on the functional material applied to DNA crystals. The Young's modulus of the crystal varies by about five orders of magnitude when functionalized with palladium. PL and semiconductive behaviors were observed when cadmium sulfide was attached. These crystals represent an expansion of the capabilities of DNA structures at these length scales, and additionally a platform for future studies exchanging the materials or altering the ligation scheme.

CdS↗
DOE OSTI2020

PdAu/YSZ composite hydrogen separation membranes with enhanced stability in the presence of CO

The effects of gold composition on the tolerance of palladium-based composite membranes to CO exposure was studied under the presence of high CO concentrations. Membranes with PdAu compositions ranging up to 41% by mass were exposed to binary 50/50 H 2 /CO gas atmospheres and both hydrogen flux and purity were monitored over time. It was observed that the highest gold composition (41%) suffered no degradation in membrane performance in terms of permeate hydrogen purity and hydrogen permeation flux during the 48 h exposure. Furthermore, for lower gold compositions, X-ray diffraction patterns suggested that carbon entered the film and could be removed by exposure to a non-CO containing gas mixture over time. However, removal of the carbon adversely affected purity; interestingly, some of the purity decline could be reversed upon re-exposure to the CO gas mixture. It is hypothesized that carbon loading in the palladium films causes lattice expansion and may even fill pore defects, thus lowering leaks through the Pd films. Furthermore, this study suggests that a membrane exposed to a CO mixture should not be cycled between CO and non-CO environments, but rather run continuously for best performance. Additionally, the choice of Pd-alloy and metal composition should be considered in regard to its carbon solubility to best predict lifetime performance.

08 HYDROGEN↗
DOE OSTI2023

Comparison of Designs of Hydrogen Isotope Separation Columns by Numerical Modeling

Mixtures of gas-phase hydrogen isotopologues (diatomic combinations of protium, deuterium, and tritium) can be separated using columns containing a solid such as palladium that reversibly absorbs hydrogen. A temperature-swing process can transport hydrogen into or out of a column by inducing temperature-dependent absorption or desorption reactions. Here, we consider two designs: a thermal cycling absorption process, which moves hydrogen back and forth between two columns, and a simulated moving bed (SMB), where columns are in a circular arrangement. We present a numerical mass and heat transport model of absorption columns for hydrogen isotope separation. It includes a detailed treatment of the absorption–desorption reaction for palladium. By comparing the isotope concentrations within the columns as a function of position and time, we observe that SMB can lead to sharper separations for a given number of thermal cycles by avoiding the remixing of isotopes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

The Surface Chemistry of Methanol on Cu 3 Pd(111): Effects of Metal Alloying and Reaction with Hydrogen

Synchrotron-based ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) was used to study the adsorption and surface chemistry of methanol on a Cu 3 Pd(111) model surface. The composition and morphological properties of the pristine Cu 3 Pd(111) substrate were analyzed using a combination of low-energy electron diffraction (LEED), scanning tunneling microscopy (STM), and low-energy ion scattering (LEIS). The results of ion scattering showed segregation of Pd toward the surface, with a Pd/Cu ratio close to 0.5, a larger value than the ratio of 0.33 expected for a Cu 3 Pd bimetallic structure. The surface of the alloy exhibited a good LEED pattern with three-fold long-range periodicities. In STM, clusters of palladium with hexagonal arrays and Pd- Pd distances of 2.7-2.8 Å were detected. Bonding to copper perturbed the electronic properties of the atoms in the Pd clusters, shifting their 4d states toward higher binding energy with respect to the Fermi level. Further, the valence band spectrum of Cu 3 Pd(111) exhibited a line shape that was very different from those displayed by Cu(111) or Pd(111). At low pressures, the adsorption of methanol on Cu 3 Pd(111) at 300 K mainly produced CH 3 O, CO and CH x species. AP-XPS showed that most Pd atoms in the surface of the Cu 3 Pd(111) alloy interacted with the decomposition products of methanol. No significant changes were observed in the core levels of copper upon the adsorption and dissociation of methanol, suggesting that the molecule mainly interacted with Pd sites of the alloy. Reaction with hydrogen led to fast removal of CH x , C and PdC x species from Cu 3 Pd(111) at moderate (< 450 K) temperatures and prevented a CH x → C transformation. If the stability of adsorbed CH 3 O is used as a descriptor for the hydrogenation of CO 2 to methanol, Cu 3 Pd should be a much better catalyst than monometallic palladium. This may be a consequence of electronic and ensemble effects in the alloy that moderate the reactivity of Pd sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

PdCu Electrocatalysts for Selective Nitrate and Nitrite Reduction to Nitrogen

Electrocatalytic conversion of nitrate in waste can enable efficient waste remediation (NO 3 - to N 2 ) or waste valorization (NO 3 - to NH 4 + ) depending on the selectivity of the catalyst. Palladium and copper electrocatalysts typically exhibit ideal nitrate and nitrite binding properties, allowing for effective destruction of nitrate. However, rational steering of selectivity through material design remains a critical challenge for PdCu electrocatalyst. Here, we use the electrochemical underpotential deposition method to synthesize palladium nanocube electrocataysts with controlled copper surface coverage (e.g., partial and full copper coatings). We then examine the potential for NO 3 - destruction (conversion) and NO 2 - reduction reaction. We identify that partial copper-coated Pd nanocubes not only effectively facilitate the reduction of 95% of NO 3 - but also increase the reduction of NO 2 - to N 2 with 89% selectivity over 20 consecutive cycles (80 h). We also show that under these conditions, the Pd(100) surface facet is exposed. Complete copper-covered Pd nanocubes effectively facilitate the reduction of ~99% of NO 3 - . Complete coverage of copper; however, prevented exposure of Pd(100) surface facet, promoting the selective reduction of NO 2 - to NH 4 + with a 70% selectivity over 20 consecutive cycles (80 h). Density functional theory (DFT) calculations show that NO 3 - and NO 2 - adsorb more strongly on the Cu(100) surface compared to the Pd(100) surface, while the NO* intermediate generated from NO 3 - or NO 2 - reduction adsorbs more strongly on the Pd surface. Furthermore, barrier calculations show that NO* can readily migrate from the Cu domain to the Pd domain and that the N–N coupling barrier on Pd is significantly diminished at high NO* coverage. Together, these results suggest that the high N 2 selectivity observed on the PdCu electrocatalyst is caused by the spillover of NO* from the Cu domains to the Pd domains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Interface synergism and engineering of Pd/Co@N-C for direct ethanol fuel cells

Direct ethanol fuel cells have been widely investigated as nontoxic and low-corrosive energy conversion devices with high energy and power densities. It is still challenging to develop high-activity and durable catalysts for a complete ethanol oxidation reaction on the anode and accelerated oxygen reduction reaction on the cathode. The materials’ physics and chemistry at the catalytic interface play a vital role in determining the overall performance of the catalysts. Herein, we propose a Pd/Co@N-C catalyst that can be used as a model system to study the synergism and engineering at the solid-solid interface. Particularly, the transformation of amorphous carbon to highly graphitic carbon promoted by cobalt nanoparticles helps achieve the spatial confinement effect, which prevents structural degradation of the catalysts. The strong catalyst-support and electronic effects at the interface between palladium and Co@N-C endow the electron-deficient state of palladium, which enhances the electron transfer and improved activity/durability. The Pd/Co@N-C delivers a maximum power density of 438 mW cm -2 in direct ethanol fuel cells and can be operated stably for more than 1000 hours. This work presents a strategy for the ingenious catalyst structural design that will promote the development of fuel cells and other sustainable energy-related technologies.

25 ENERGY STORAGE↗
DOE OSTI2022

Flexible Copper Metal Circuits via Desktop Laser Printed Masks

A novel process is demonstrated that produces patterns of electrically conductive copper on a flexible polyimide film substrate using standard desktop laser printed toner and near room temperature aqueous chemistry. The laser toner acts as a mask to selectively block the ion exchange self-metallization (IESM) reduction reaction that forms nanoscale silver or palladium coatings at the polyimide surface. The silver or palladium IESM coating is then used as a catalyst for electroless deposition of copper. Under appropriate conditions, the copper is deposited selectively on top of the catalyst layer. The resulting copper layer has a measured sheet resistance as low as 0.3 Ohms/sq. Electrical isolation was measured between copper traces spaced as close as 300 microns, and high conductivity was measured along traces with widths as low as 200 microns. The minimum pattern size appears to be limited primarily by the resolution of the laser toner pattern, as the IESM metal layer was observed to follow the contours of individual toner particles. Here, the process avoids the use of high temperature, vacuum, and organic solvents and is thus suitable for very low cost prototyping or distributed manufacturing of simple electronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

π‐Extended Donor–Acceptor Porphyrins and Metalloporphyrins for Antimicrobial Photodynamic Inactivation

Abstract Free base, zinc and palladium π‐extended porphyrins containing fused naphthalenediamide units were employed as photosensitizers in antimicrobial photodynamic therapy (aPDT). Their efficacy, assessed by photophysical and in vitro photobiological studies on Gram‐positive bacteria, was found to depend on metal coordination, showing a dramatic enhancement of photosensitizing activity for the palladium complex.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Volcano‐like Activity Trends in Au@Pd Catalysts: The Role of Pd Loading and Nanoparticle Size

The addition of palladium (Pd) to preformed gold nanoparticles (Au NPs) enables the formation of core‐shell structures with enhanced catalytic performance in oxidation reactions. However, predicting the precise palladium content required to achieve maximum catalytic activity remains difficult based on current understanding. Herein, Pd was systematically introduced onto titania‐supported Au NPs (2, 6, and 10 nm) to evaluate their performance in benzyl alcohol oxidation. A volcano‐like trend in catalytic activity was observed, where activity increased with Pd addition, peaked, and then declined. The Pd loading required for maximum activity depended on Au NP size: ≈40 at% Pd/Au for 2.6 nm, ≈20 at% Pd/Au for 6.4 nm, and ≈12.5 at% Pd/Au for 10.6 nm. For Au NPs > 6 nm, peak activity aligned with monolayer Pd coverage, while for smaller NPs (2–3 nm), optimal Pd content was below monolayer predictions. X‐ray absorption spectroscopy revealed a core‐shell structure at low Pd content, but higher Pd loadings led to Pd diffusion into the Au core. This structural transformation likely caused activity decline, indicating that AuPd alloying negatively impacts catalysis. These results highlight that core‐shell Au@Pd catalysts outperform AuPd alloys and provide crucial insights for designing highly active bimetallic catalysts.

X-ray absorption spectroscopy↗
DOE OSTI2026

RuKY Catalyst‐Packed Permeation Membrane for Quantitative Ammonia and d3‐Ammonia Dehydrogenation to Ultrapure Hydrogen

Ammonia is a promising carbon-free hydrogen carrier, but incomplete ammonia dehydrogenation (cracking) generates atmospheric emissions of NO x , a potent greenhouse gas. Additionally, incomplete cracking of ammonia leads to regulatory challenges in nuclear and fusion power, where tritiated ammonia (NT 3 ) emissions are strictly controlled. Therefore, we report the use of low-temperature ammonia dehydrogenation catalysts (3%Ru/1%Y/12%K/Al 2 O 3 ) in a palladium alloy H 2 permeation membrane for quantitative conversion of ammonia into hydrogen and nitrogen at industry-relevant conditions. This catalytic membrane reactor system achieved an astonishing effluent concentration of <1 ppm at 450°C under a 100% NH 3 stream, which is far beyond the 99.6% conversion target required for the adoption of ammonia as a vehicle fuel. The low-temperature ammonia dehydrogenation catalyst was tested in a packed bed reactor with NH 3 and ND 3 to both elucidate the reaction mechanism and to quantify the kinetic isotope effect of the membrane reactor. The rate-limiting step at temperatures relevant to the palladium membrane are isotope independent, indicating that the isotopologue content will not modify the desired reaction kinetics. By reducing emissions to below-trace levels with no additional separation, this work provides a path to greatly simplified and miniaturized ammonia cracking processes.

ammonia decomposition↗