Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESSED SKIN - CUT-OUTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Direct Numerical Simulation of Transitional and Turbulent Flow Over a Heated Flat Plate Using Finite-Difference Schemes

The work in this report was conducted at NASA Ames Research Center during the period from August 1993 to January 1995 deals with the direct numerical simulation of transitional and turbulent flow at low Mach numbers using high-order-accurate finite-difference techniques. A computation of transition to turbulence of the spatially-evolving boundary layer on a heated flat plate in the presence of relatively high freestream turbulence was performed. The geometry and flow conditions were chosen to match earlier experiments. The development of the momentum and thermal boundary layers was documented. Velocity and temperature profiles, as well as distributions of skin friction, surface heat transfer rate, Reynolds shear stress, and turbulent heat flux were shown to compare well with experiment. The numerical method used here can be applied to complex geometries in a straightforward manner.

Madavan, Nateri K.↗
NASA NTRS2004

A Micromachined Geometric Moire Interferometric Floating-Element Shear Stress Sensor

This paper presents the development of a floating-element shear stress sensor that permits the direct measurement of skin friction based on geometric Moir interferometry. The sensor was fabricated using an aligned wafer-bond/thin-back process producing optical gratings on the backside of a floating element and on the top surface of the support wafer. Experimental characterization indicates a static sensitivity of 0.26 microns/Pa, a resonant frequency of 1.7 kHz, and a noise floor of 6.2 mPa/(square root)Hz.

Horowitz, S.↗
NASA NTRS2018

Test and Analysis of Full-Scale 27.5-Foot-Diameter Stiffened Metallic Launch Vehicle Cylinders

The Shell Buckling Knockdown Factor Project (SBKF) was established with the goal of developing improved (i.e., less-conservative, more robust) shell buckling knockdown factors (KDFs) for modern launch-vehicle structures. To this end, SBKF has engaged in several activities to support the development, validation, and implementation of the new design factors, including subscale and full-scale structural testing. Tests on eight different subscale, 8-foot-diameter, integrally stiffened aluminum-lithium 2195 (Al-Li 2195) cylinders were conducted in order to obtain the majority of the required validation data. In addition, two full-scale, 27.5-foot-diameter, Al-Li 2195, integrally stiffened cylinders were tested to provide additional validation data and to determine structural scaling trends. Presented herein are the details of a recent analysis model development and test and analysis correlation effort on the full-scale test articles. The effects of selected modeling assumptions and approaches are discussed, and results from a modeling sensitivity study are presented. It was found that simplified finite element models, that assume nominal test article geometry and material properties, can predict the overall response characteristics well. However, several discrepancies in the test and analysis results were observed. A sensitivity study was performed to determine the effects of several modeling assumptions and address the observed discrepancies. The results from the study indicated that the evolution of local skin pocket buckling and the presence of residual stresses due to the manufacturing process can have a significant influence on the predicted buckling response of the cylinders considered.

Lovejoy, Andrew E.↗
NASA NTRSDate not supplied

Wall-modeled LES of the Three-dimensional Speed Bump Experiment

We evaluate the performance of wall-modeled large eddy simulation (WMLES) in predicting smooth-body turbulent flow separation for a three-dimensional Gaussian-shaped speed bump geometry. The Reynolds number based on the bump length is 2 million, and an unstructured compressible finite-volume solver is used with an equilibrium wall model and dynamic subgrid scale model. Spanwise periodic simulations of the centerline two-dimensional bump were used to assess grid resolution requirements, and resolving the thin internal layer in the accelerating region was found to be necessary to correctly capture the downstream separated flow region. Based on these insights, an optimized grid that was smaller by a factor of two provided comparable accuracy to a finer grid that has been used by us and other researchers in past studies. Using insights gained from the spanwise periodic simulation, an unstructured polyhderal grid with about 250 million cells was used for the three-dimensional (3D) configuration with inviscid tunnel side and top walls. Detailed comparisons of wall skin-friction coefficient, wall pressure, velocity and turbulent stresses with available experimental data indicated excellent agreement. While the low-Reynolds Number Spalart-Allmaras RANS model with rotation/curvature correction gave qualitatively good agreement with experiments, WMLES showed significantly more accurate quantitative predictions of the flowfield. The 3D WMLES showed good agreement with experiments in the separated region, and the centerplane results indicated a different separation topology compared to the spanwise periodic simulation.

Computational Fluid Dynamics↗
NASA NTRS1954

Experimental Stress Analysis of Stiffened Cylinders with Cutouts : Shear Load

A cylindrical semimonocoque shell of circular cross section was mounted as a cantilever and loaded by a direct shear at the tip. The cylinder was tested with no cutout, with a rectangular cutout on the tension side, and with the cutout centered on the neutral axis on one side of the cylinder. The cutout was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 and 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each case, and the stresses obtained are presented in tables. (author)

Rosecrans, Richard↗
NASA NTRS1981

Simple approximations for the asymptotic description of the interaction between a normal shock wave and a turbulent boundary layer at transonic speeds

The asymptotic description of the interaction between a normal shock wave and a turbulent boundary layer is reviewed. The layers necessary in a rational analysis of the interaction are discussed with emphasis on the differences from an interaction with a laminar boundary layer, the uncoupling of solutions for the distribution of pressure and skin friction at the wall, and the role of the Reynolds shear stress in these solutions. The accuracy of asymptotic solutions in flows at Reynolds numbers of technical interest is discussed. Solutions for the distribution of pressure and skin friction at the wall and the shape of the shock are considered for the case where the flow is near separation. For the pressure and skin friction, it is possible to write two simplified partial solutions, one valid at the beginning of the interaction and one valid somewhat downstream of the shock wave. A solution composed of these two parts and a linear interpolation between them appears to give good comparison with experiment; one unknown constant, independent of the parameters of the interaction, must be found from experiment. The simplified relations are presented. Comparison of numerical computations with experimental data indicates a possible value for the constant and shows quite satisfactory results.

Adamson, T. C., Jr.↗
NASA NTRS2001

Absence of arterial baroreflex modulation of skin sympathetic activity and sweat rate during whole-body heating in humans

1. Prior findings suggest that baroreflexes are capable of modulating skin blood flow, but the effects of baroreceptor loading/unloading on sweating are less clear. Therefore, this project tested the hypothesis that pharmacologically induced alterations in arterial blood pressure in heated humans would lead to baroreflex-mediated changes in both skin sympathetic nerve activity (SSNA) and sweat rate. 2. In seven subjects mean arterial blood pressure was lowered (approximately 8 mmHg) and then raised (approximately 13 mmHg) by bolus injections of sodium nitroprusside and phenylephrine, respectively. Moreover, in a separate protocol, arterial blood pressure was reduced via steady-state administration of sodium nitroprusside. In both normothermia and heat-stress conditions the following responses were monitored: sublingual and mean skin temperatures, heart rate, beat-by-beat blood pressure, skin blood flow (laser-Doppler flowmetry), local sweat rate and SSNA (microneurography from peroneal nerve). 3. Whole-body heating increased skin and sublingual temperatures, heart rate, cutaneous blood flow, sweat rate and SSNA, but did not change arterial blood pressure. Heart rate was significantly elevated (from 74 +/- 3 to 92 +/- 4 beats x min(-1); P < 0.001) during bolus sodium nitroprusside-induced reductions in blood pressure, and significantly reduced (from 92 +/- 4 to 68 +/- 4 beats x min(-1); P < 0.001) during bolus phenylephrine-induced elevations in blood pressure, thereby demonstrating normal baroreflex function in these subjects. 4. Neither SSNA nor sweat rate was altered by rapid (bolus infusion) or sustained (steady-state infusion) changes in blood pressure regardless of the thermal condition. 5. These data suggest that SSNA and sweat rate are not modulated by arterial baroreflexes in normothermic or moderately heated individuals.

Clinical Trial↗
NASA NTRS1977

Design and fabrication of graphite-epoxy bolted wing skin splice specimens

Graphite-epoxy bolted joint specimens were designed and fabricated. These specimens were to be representative of a side-of-body wing skin splice with a 20-year life expectancy in a commercial transport environment. Preliminary tests were performed to determine design values of bearing and net tension stresses. Based upon the information developed, a three-fastener-wide representative wing skin splice was designed for a load of 2627 KN/m (15,000 lbf/in.). One joint specimen was fabricated and tested at NASA. The wing skin splice failed at 106 percent of design ultimate load. This joint design achieved all static load objectives. Fabrication of six specimens, together with their loading fixtures, was completed, and the specimens were delivered to NASA-LRC.

Johnson, R. W.↗
NASA NTRS1988

Skin friction measurements by laser interferometry in swept shock wave/turbulent boundary-layer interactions

The laser interferometric skin friction meter was used to measure wall shear stress distributions in two interactions of fin-generated swept shock waves with turbulent boundary layers. The basic research configuration was an unswept sharp-leading-edge fin of variable angle mounted on a flatplate. The results indicate that such measurements are practical in high-speed interacting flows, and that a repeatability of + or - 6 percent or better is possible. Marked increases in wall shear were observed in both swept interactions tested.

Kim, Kwang-Soo↗
NASA NTRS1996

Colors Of Liquid Crystals Used To Measure Surface Shear Stresses

Developmental method of mapping shear stresses on aerodynamic surfaces involves observation, at multiple viewing angles, of colors of liquid-crystal surface coats illuminated by white light. Report describing method referenced in "Liquid Crystals Indicate Directions Of Surface Shear Stresses" (ARC-13379). Resulting maps of surface shear stresses contain valuable data on magnitudes and directions of skin friction forces associated with surface flows; data used to refine mathematical models of aerodynamics for research and design purposes.

Reda, D. C.↗
NASA NTRS1978

Bi-directional, buried-wire skin-friction gage

A compact, nonobtrusive, bi-directional, skin-friction gage was developed to measure the mean shear stress beneath a three-dimensional boundary layer. The gage works by measuring the heat flux from two orthogonal wires embedded in the surface. Such a gage was constructed and its characteristics were determined for different angles of yaw in a calibration experiment in subsonic flow with a Preston tube used as a standard. Sample gages were then used in a fully three-dimensional turbulent boundary layer on a circular cone at high relative incidence, where there were regimes of favorable and adverse pressure gradients and three-dimensional separation. Both the direction and magnitude of skin friction were then obtained on the cone surface.

Higuchi, H.↗
NASA NTRS1988

Correlations of velocity and temperature fluctuations in the stagnation-point flow of circular cylinder in turbulent flow

The present analyses of boundary layer flow and turbulence transport attempt to characterize the influence of freestream turbulence on the surface heat-transfer rate and stagnation point region skin friction of a circular cross-section cylinder in turbulent flow. The Reynolds stress-transport equations and k-epsilon two-equation turbulence modeling are used, yielding time-averaged turbulence double-correlations, mean-flow properties, surface heat-transfer rate, and skin-friction with freestream isotropic turbulence. A comparison of analytical results with experimental data indicates that large Reynolds normal stresses are induced at the boundary layer edge by the kinetic energy of the turbulence.

Wang, C. R.↗
NASA NTRS1953

Experimental Stress Analysis of Stiffened Cylinders with Cutouts.pure Torsion

Torsion tests were made on a cylindrical semimonocoque shell of circular cross section. The cylinder was first tested without a cutout, and then with a rectangular cutout which was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 to 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each size of cutout, and the stresses obtained are presented in tables. (author)

LOADS AND STRESSES, STRUCTURAL - TORSION↗
NASA NTRS1954

Experimental Stress Analysis of Stiffened Cylinders with Cutouts : Pure Bending

Bending tests were made on a cylindrical semimonocoque shell of circular cross section. The cylinder was tested without a cutout and then with a rectangular cutout which was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 to 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each size of cutout, and the stresses obtained are presented in tables. (author)

Schlechte, Floyd R↗
NASA NTRS2000

Effects of whole body heating on dynamic baroreflex regulation of heart rate in humans

The purpose of this project was to identify whether dynamic baroreflex regulation of heart rate (HR) is altered during whole body heating. In 14 subjects, dynamic baroreflex regulation of HR was assessed using transfer function analysis. In normothermic and heat-stressed conditions, each subject breathed at a fixed rate (0. 25 Hz) while beat-by-beat HR and systolic blood pressure (SBP) were obtained. Whole body heating significantly increased sublingual temperature, HR, and forearm skin blood flow. Spectral analysis of HR and SBP revealed that the heat stress significantly reduced HR and SBP variability within the high-frequency range (0.2-0.3 Hz), reduced SBP variability within the low-frequency range (0.03-0.15 Hz), and increased the ratio of low- to high-frequency HR variability (all P < 0.01). Transfer function gain analysis showed that the heat stress reduced dynamic baroreflex regulation of HR within the high-frequency range (from 1.04 +/- 0.06 to 0.54 +/- 0.6 beats. min(-1). mmHg(-1); P < 0.001) without significantly affecting the gain in the low-frequency range (P = 0.63). These data suggest that whole body heating reduced high-frequency dynamic baroreflex regulation of HR associated with spontaneous changes in blood pressure. Reduced vagal baroreflex regulation of HR may contribute to reduced orthostatic tolerance known to occur in humans during heat stress.

Non-NASA Center↗
NASA NTRS1976

Structural analysis of wind turbine rotors for NSF-NASA Mod-0 wind power system

Preliminary estimates are presented of vibratory loads and stresses in hingeless and teetering rotors for the proposed NSF-NASA Mod-0 wind power system. Preliminary blade design utilizes a tapered tubular aluminum spar which supports nonstructural aluminum ribs and skin and is joined to the rotor hub by a steel shank tube. Stresses in the shank of the blade are calculated for static, rated, and overload operating conditions. Blade vibrations were limited to the fundamental flapping modes, which were elastic cantilever bending for hingeless rotor blades and rigid-body rotation for teetering rotor blades. The MOSTAB-C computer code was used to calculate aerodynamic and mechanical loads. The teetering rotor has substantial advantages over the hingeless rotor with respect to shank stresses, fatigue life, and tower loading. The hingeless rotor analyzed does not appear to be structurally stable during overloads.

Spera, D. A.↗
NASA NTRS1992

Flow prediction over a transport multi-element high-lift system and comparison with flight measurements

Accurate prediction of surface-pressure distributions, merging boundary-layers, and separated-flow regions over multi-element high-lift airfoils is required to design advanced high-lift systems for efficient subsonic transport aircraft. The availability of detailed measurements of pressure distributions and both averaged and time-dependent boundary-layer flow parameters at flight Reynolds numbers is critical to evaluate computational methods and to model the turbulence structure for closure of the flow equations. Several detailed wind-tunnel measurements at subscale Reynolds numbers were conducted to obtain detailed flow information including the Reynolds-stress component. As part of a subsonic-transport high-lift research program, flight experiments are conducted using the NASA-Langley B737-100 research aircraft to obtain detailed flow characteristics for support of computational and wind-tunnel efforts. Planned flight measurements include pressure distributions at several spanwise locations, boundary-layer transition and separation locations, surface skin friction, as well as boundary-layer profiles and Reynolds stresses in adverse pressure-gradient flow.

Vijgen, P. M. H. W.↗
NASA NTRS2005

Computational Study of Separating Flow in a Planar Subsonic Diffuser

A computational study of the separated flow through a 2-D asymmetric subsonic diffuser has been performed. The Wind Computational Fluid Dynamics code is used to predict the separation and reattachment behavior for an incompressible diffuser flow. The diffuser inlet flow is a two-dimensional, turbulent, and fully-developed channel flow with a Reynolds number of 20,000 based on the centerline velocity and the channel height. Wind solutions computed with the Menter SST, Chien k-epsilon, Spalart-Allmaras and Explicit Algebraic Reynolds Stress turbulence models are compared with experimentally measured velocity profiles and skin friction along the upper and lower walls. In addition to the turbulence model study, the effects of grid resolution and use of wall functions were investigated. The grid studies varied the number of grid points across the diffuser and varied the initial wall spacing from y(sup +) = 0.2 to 60. The wall function study assessed the applicability of wall functions for analysis of separated flow. The SST and Explicit Algebraic Stress models provide the best agreement with experimental data, and it is recommended wall functions should only be used with a high level of caution.

DalBello, Teryn↗