Search NASA⌕ Search

SEARCH · Search NASA

Results for “coupon”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Environmental effects on composites for aircraft

A number of ongoing, long-term environmental effects programs for composite materials are evaluated. The flight service experience was evaluated for 142 composite aircraft components after more than 5 years and 1 million successful component flight hours. Ground-based outdoor exposures of composite material coupons after 3 years of exposure at 5 sites have reached equilibrium levels of moisture pickup which are predictable. Solar ultraviolet-induced material loss is discussed for these same exposures. No significant degradation was observed in residual strength for either stressed or unstressed specimens, or for exposures to aviation fuels and fluids.

Pride, R. A.↗
NASA NTRS1978

Development of advanced composite structures

Composite structure programs: the L-1011 Advanced Composite Vertical Fin (ACVF), the L-1011 Advanced Composite Aileron, and a wing study program were reviewed. These programs were structured to provide the technology and confidence for the use of advanced composite materials for primary and secondary structures of future transport aircraft. The current status of the programs is discussed. The results of coupon tests for both material systems are presented as well as the ACVF environmental (moisture and temperature) requirements. The effect of moisture and temperature on the mechanical properties of advanced composite materials is shown. The requirements set forth in the FAA Certification Guidelines for Civil Composite Aircraft Structures are discussed as they relate to the ACVF.

Stauffer, W. A.↗
NASA NTRS1978

Microstructure and mechanical properties of quenched and tempered 300M steel

Type 300M steel, which is being used for the landing gear on the space shuttle orbiter, was subjected to a wide range of quenched and tempered heat treatments. The plane-strain fracture toughness and the tensile ultimate and yield strengths were evaluated. Cryogenic mechanical properties were obtained for conventionally heat-treated steel. The microstructure of all heat-treated test coupons was studied both optically and by transmission electron microscopy. Fracture surfaces were studied by means of scanning electron microscopy. Results indicate that substantial improvement in toughness with no loss in strength can be accomplished in quenched and tempered steel by austenitizing at 1255 K or higher. Low fracture toughness in conventionally austenitized 300M steel (1144 K) appears to be caused by undissolved precipitates, seen both in the submicrostructure and on the fracture surface, which promote failure by quasi-cleavage. The precipitates appeared to dissolve in the range 1200 to 1255 K.

Youngblood, J. L.↗
NASA NTRS1978

Design and Fabrication of a Ring-Stiffened Graphite-Epoxy Corrugated Cylindrical Shell

Design and fabrication of supplement test panels that represent key portions of the cylinder are described, as are supporting tests of coupons, sample joints, and stiffening ring elements. The cylindrical shell is a ring-stiffened, open corrugation design that uses T300/5208 graphite-epoxy tape as the basic material for the shell wall and stiffening rings. The test cylinder is designed to withstand bending loads producing the relatively low maximum load intensity in the shell wall of 1,576 N/cm. The resulting shell wall weight, including stiffening rings and fasteners, is 0.0156 kg/m. The shell weight achieved in the graphite-epoxy cylinder represents a weight saving of approximately 23 percent, compared to a comparable aluminum shell. A unique fabrication approach was used in which the cylinder wall was built in three flat segments, which were then wrapped to the cylindrical shape. Such an approach, made possible by the flexibility of the thin corrugated wall in a radial direction, proved to be a simple approach to building the test cylinder. Based on tooling and fabrication methods in this program, the projected costs of a production run of 100 units are reported.

Johnson, R., Jr.↗
NASA NTRS1977

Tensile and compressive behavior of Borsic/aluminum

The results of an experimental investigation of the mechanical behavior of Borsic/aluminum are presented. Composite laminates were tested in tension and compression for monotonically increasing load and also for variable loading cycles in which the maximum load was increased in each successive cycle. It is shown that significant strain-hardening, and corresponding increase in yield stress, is exhibited by the metal matrix laminates. For matrix dominated laminates, the current yield stress is essentially identical to the previous maximum stress, and unloading is essentially linear with large permanent strains after unloading. For laminates with fiber dominated behavior, the yield stress increases with increase in the previous maximum stress, but the increase in yield stress does not keep pace with the previous maximum stress. These fiber dominated laminates exhibit smaller nonlinear strains, reversed nonlinear behavior during unloading, and smaller permanent strains after unloading. Compression results from sandwich beams and flat coupons are shown to differ considerably. Results from beam specimens tend to exhibit higher values for modulus, yield stress, and strength.

Herakovich, C. T.↗
NASA NTRS1978

Design and fabrication of a large graphite-epoxy cylindrical shell

This paper describes the design and fabrication of a 10-foot diameter by 10-foot long graphite-epoxy cylinder and reports the results of developmental tests conducted with sample joints, material coupons, and stiffening ring elements. The cylindrical shell is a ring-stiffened, open corrugation design using T300/5208 graphite-epoxy tape as the basic material for the shell wall and stiffening rings. The cylinder is designed to withstand bending loads producing the relatively low maximum load intensity of 900 lb/in. The resulting shell wall weight, including stiffening rings and fasteners, is 0.37 lb/sq ft. The shell weight expected in the graphite-epoxy cylinder represents a weight savings of approximately 23 percent over that of a comparable aluminum shell. The cylinder wall was built in three flat segments which were wrapped to the cylindrical shape upon assembly. Such an approach, made possible by the flexibility of the thin corrugated wall in a radial direction, proved to be a simple one.

Johnson, R., Jr.↗
NASA NTRS1979

Fatigue and fracture

The effects of the load/temperature environment of the shuttle on the fatigue life of the body-flap were investigated by conducting real time and accelerated flight-by-flight tests up to 500 flights on coupons containing holes. On the fracture side, much is known about the sensitivity of the tensile strengths of composites to holes and other flaws, predominantly at room temperature. The effects of notches were assessed for graphite/polyimides at the expected temperature extremes of the body-flap: 117K (-250 F) to 589K (600 F). Results indicate that the shuttle temperature extremes may affect fatigue properties HTS/PMR-15. There is no significant effect of temperature on notch-strength. Tensile strengths for specimens with holes and slots are equal.

Illg, W.↗
NASA NTRS1979

High temperature - low mass solar blanket

Interconnect materials and designs for use with ultrathin silicon solar cells are discussed, as well as the results of an investigation of the applicability of parallel-gap resistance welding for interconnecting these cells. Data relating contact pull strength and cell electrical degradation to variations in welding parameters such as time, voltage and pressure are presented. Methods for bonding ultrathin cells to flexible substances and for bonding thin (75 micrometers) covers to these cells are described. Also, factors influencing fabrication yield and approaches for increasing yield are discussed. The results of vacuum thermal cycling and thermal soak tests on prototype ultrathin cell test coupons and one solar module blanket are presented.

Mesch, H. G.↗
NASA NTRS1978

Interim results of long-term environmental exposures of advanced composites for aircraft applications

Interim results from a number of ongoing, long-term environmental effects programs for composite materials are reported. The flight service experience is evaluated for 142 composite aircraft components after more than five years and one million successful component flight hours. Ground-based outdoor exposures of composite material coupons after 3 years of exposure at five sites have reached equilibrium levels of moisture pickup which are predictable. Solar ultraviolet-induced material loss is discussed for these same exposures. No significant degradation has been observed in residual strength for either stressed or unstressed specimens, or for exposures to aviation fuels and fluids.

Pride, R. A.↗
NASA NTRS1978

Static evaluation of surface coatings for compliant gas bearings in an oxidizing atmosphere to 650 C

Hard wear-resistant coatings and soft low shear strength coatings were developed for an air-lubricated compliant journal bearing for a future automotive gas turbine engine. The coatings were expected to function in either 540 or 650 C ambient. Soft lubricant coatings were generally limited in temperature. Therefore emphasis was on the hard wear-resistant coatings. The coating materials covered were TiC, B4C, Cr3C2, WC, SiC, CrB2, TiB2, Cr2O3, Al2O3, Si3N4, Tribaloy 800, CaF2, CaF2-BaF2 eutectic, Ni-Co, silver, CdO-graphite and proprietary compounds. The coatings on test coupons were subjected to static oven screening tests. The test consisted of exposure of material samples in an oven for 300 h at the maximum temperature (540 or 650 C) and ten temperature cycles from room temperature to the maximum service temperature. On the basis of the specimen examinations the following coatings were recommended for future wear tests: TiC (sputtered), Cr2O3 (sputtered), Si3N4 (sputtered), CdO and graphite (fused), Kaman DES (a proprietary coating), CrB2 (plasma sprayed), Cr3C2 (detonation gun) and NASA PS-106 (plasma sprayed).

Bhushan, B.↗
NASA NTRS1979

High temperature, low mass solar blanket development

This paper presents methods of incorporating ultrathin silicon solar cells into photovoltaic blankets for space applications. This type of cell has the highest power-to-mass ratio and best performance under space radiation of any silicon solar cell. Interconnect materials and designs, and the results of the investigation of the applicability of parallel-gap resistance welding for interconnecting ultrathin cells are discussed. Data relating contact pull strength and cell electrical degradation to welding parameters such as time, voltage, and pressure are presented. Methods for bonding ultrathin cells to flexible substrates and for bonding thin covers to these cells are described, and the results of vacuum thermal cycling and thermal soak tests on prototype ultrathin cell test coupons are included.

Mesch, H. G.↗
NASA NTRS1980

Effects of method of loading and specimen configuration on compressive strength of graphite/epoxy composite materials

Three test schemes were examined for testing graphite/epoxy (Narmco T300/5208) composite material specimens to failure in compression, including an adaptation of the IITRI "wedge grip" compression fixture, a face-supported-compression fixture, and an end-loaded-coupon fixture. The effects of specimen size, specimen support arrangement and method of load transfer on compressive behavior of graphite/epoxy were investigated. Compressive stress strain, strength, and modulus data obtained with the three fixtures are presented with evaluations showing the effects of all test parameters, including fiber orientation. The IITRI fixture has the potential to provide good stress/strain data to failure for unidirectional and quasi-isotropic laminates. The face supported fixture was found to be the most desirable for testing + or - 45 s laminates.

Clark, R. K.↗
NASA NTRS1982

Double-Adhesive Tape Test Reduces Waste

New method for testing peel strength of particular thermal-control tape used on Space Shuttle orbiter radiators requires only half amount of tape of method previously employed. Thermal-control tape consists of layers of FEP, silver, Inconel metal, adhesive, Kapton Film, and second adhesive layer. Method also avoids cost of labor and materials to prepare second test coupon and can be adapted for testing other types of double-faced adhesive tapes in military, industrial and consumer applications.

Lee, L. C.↗
NASA NTRS1980

Three dimensional inelastic finite element analysis of laminated composites

Formulations of the inelastic response of laminated composites to thermal and mechanical loading are used as the basis for development of the computer NALCOM (Nonlinear Analysis of Laminated Composites) computer program which uses a fully three dimensional isoparametric finite element with 24 nodes and 72 degrees of freedom. An incremental solution is performed with nonlinearities introduced as pseudoloads computed for initial strains. Equilibrium iteration may be performed at every step. Elastic and elastic-plastic response of boron/epoxy and graphite/epoxy graphite/epoxy and problems of curing 0/90 sub s Gr/Ep laminates with and without circular holes are analyzed. Mechanical loading of + or - 45sub s Gr/Ep laminates is modeled and symmetry conditions which exist in angle-ply laminates are discussed. Results are compared to experiments and other analytical models when possible. All models are seen to agree reasonably well with experimetnal results for off-axis tensile coupons. The laminate analyses show the three dimensional effects which are present near holes and free corners.

Griffin, O. H., Jr.↗
NASA NTRS1980

Ceramic applications in turbine engines

Ceramic material characterization and testing of ceramic nozzle vanes, turbine tip shrouds, and regenerators disks at 36 C above the baseline engine TIT and the design, analysis, fabrication and development activities are described. The design of ceramic components for the next generation engine to be operated at 2070 F was completed. Coupons simulating the critical 2070 F rotor blade was hot spin tested for failure with sufficient margin to quality sintered silicon nitride and sintered silicon carbide, validating both the attachment design and finite element strength. Progress made in increasing strength, minimizing variability, and developing nondestructive evaluation techniques is reported.

Hudson, M. S.↗
NASA NTRS1981

Approximate analysis of postbuckled through-width delaminations

An approximate analysis was developed to analyze the postbuckling behavior of through-width delaminations in a laminated coupon. The analysis contains two parameters which are determined using a finite element analysis. After calculating the parameters for a few configurations, the approximate analysis was used to analyze many other configurations. Lateral deflections and mode I strain-energy release rates obtained with the approximate analysis were compared with results from the finite element analysis. For the configurations analyzed, the approximate analysis agreed very well with the finite element results.

Whitcomb, J. D.↗
NASA NTRS1981

Statistical distribution of mechanical properties for three graphite-epoxy material systems

Graphite-epoxy composites are playing an increasing role as viable alternative materials in structural applications necessitating thorough investigation into the predictability and reproducibility of their material strength properties. This investigation was concerned with tension, compression, and short beam shear coupon testing of large samples from three different material suppliers to determine their statistical strength behavior. Statistical results indicate that a two Parameter Weibull distribution model provides better overall characterization of material behavior for the graphite-epoxy systems tested than does the standard Normal distribution model that is employed for most design work. While either a Weibull or Normal distribution model provides adequate predictions for average strength values, the Weibull model provides better characterization in the lower tail region where the predictions are of maximum design interest. The two sets of the same material were found to have essentially the same material properties, and indicate that repeatability can be achieved.

Reese, C.↗
NASA NTRS1981

An investigation of adhesive/adherend and fiber matrix interactions

Research during the report period focused on continued scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) of lap shear samples and flatwise tensile specimens and on the surface characterization of TiO2, Ti 6-4, and Ti powders with particular emphasis on their interaction with primer solutions of both polyphenylquinoxaline and LaRC-13 polyimide. The use of SEM and XPS in the analysis of Ti 6-4 adherend surfaces is described as well as differences in Ti 6-4 surface composition after different chemical pretreatments. Analysis of fractured surfaces is used to established the failure mode. The surface acidity of Ti 6-4 coupons can be established by reflectance visible spectroscopy using indicator dyes.

Beck, B.↗