SEARCH · Search NASA

Results for “directional heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Solar wind theory and modelling

The outflow of coronal plasma into interplanetary space is a consequence of the coronal heating process. Therefore the formation of the corona and the acceleration of the solar wind should be treated as a single problem. Traditionally the mass or particle flux emanating from the extended corona has been thought of as being determined by the coronal temperature or scale height and the coronal (base) density. This argument follows from considerations of the momentum balance of the corona-wind system from which one obtains models of a close to hydrostatic corona out to the critical point where the flow becomes supersonic. With this approach to the acceleration of the wind is has been difficult to reconcile the relatively small variation observed in the proton flux at 1 AU with the predicted exponential dependence of the proton flux on the coronal temperature. In this talk we would like to emphasize another approach in which coronal energetics play the primary role. The deposition of energy into the corona through some 'mechanical' energy flux is balanced by the various energy sinks available to the corona and the sum of these processes determine the coronal structure, i.e. its temperature and density. The corona loses energy through heat conduction into the transition region, through radiative losses, and through the gravitational potential energy and kinetic energy put into the solar wind itself. We will show from a series of models of the chromosphere transition region-corona-solar wind system that most of the energy deposited in a magnetically open region will go into the solar wind, with roughly half going into kinetic energy and half into lifting the plasma out of the solar gravity field. The coronal base density will adjust itself in such a way that the heat conductive flux flowing into the transition region is radiated away in the upper chromosphere. The coronal temperature is set by the requirements that most of the deposited energy goes into accelerating the solar wind; the coronal scale height will adjust itself so that the solar wind energy losses conform to the amplitude of the input energy. These processes are modified by the 'mode' of energy deposition, and we will show the effects on coronal structure of changing the parameters describing coronal heating as well as the effects of including a helium fluid in the models. However, the location, scale height and/or form of the energy deposition (i.e. heating or direct acceleration) are not too important for the solar wind, the coronal density and temperature structure will vary with the 'mode' of energy deposition, but the solar wind mass flux depends mainly on the amplitude of the energy flux.

Hansteen, Viggo H.↗

NASA NTRS1996

Toward an Astrophysical Theory of Chondrites

Sunlike stars are born with disks. Based on our recently developed model to understand how a magnetized new star interacts with its surrounding accretion disk, we advanced an astrophysical theory for the early solar system. The aerodynamic drag of a magnetocentrifugally driven wind out of the inner edge of a shaded disk could expose solid bodies lifted into the heat of direct sunlight, when material is still accreting onto the protosun. Chondrules, calcium-aluminum-rich inclusions (CAI's), and rims could form along the flight for typical self-consistent parameters of the outflow in different stages of star formation. The process gives a natural sorting mechanism that explains the size distribution of CAI's and chondrules, as well as their associated rims. Chondritic bodies then subsequently form by compaction of the processed solids with the ambient nebular dust comprising the matrices after their reentry at great distances from the original launch radius.

Shang, Hsien↗

NASA NTRS1996

Optical Properties of Selective Emitter Materials for Thermophotovoltaic Applications

We investigate the optical properties of new "selective emitter" materials for possible use in high-efficiency thermophotovoltaic power systems. These are systems which directly convert heat to radiation at a wavelength closely matched to the bandgap energy of the solar cell. Candidate materials which have strong absorption lines fairly close to the bandgap of good solar-cell materials were chosen for study. Their emittance was measured as a function of wavelength to evaluate their promise as selective TPV emitters. Useful and informative results were obtained. Some of these results were presented at a January 1996 solar energy conference of the American Institute of Aeronautics and Astronautics.

Hambourger, Paul D.↗

NASA NTRS1998

SOHO Ultraviolet Coronagraph Spectrometer (UVCS) Mission Operations and Data Analysis

The scientific goal of UVCS is to obtain detailed empirical descriptions of the extended solar corona as it evolves from a period of minimum activity to maximum and to use these descriptions to identify and understand the physical processes responsible for coronal heating, solar wind acceleration, coronal mass ejections (CME's), and the phenomena that establish the plasma properties of the solar wind as measured by the CELIAS/SOHO experiment. We must observe a wide range of conditions (e.g., heating rate, impulsive mass ejections, magnetic field opening) in order to choose among competing theoretical explanations of the observed coronal structures and dynamics. During the first year of scientific observations (1 April 1996 through 31 March 1997), the LTVCS made the first extensive ultraviolet spectroscopic observations above the base of the solar corona. Those observations revealed extremely high most probable speeds along the line of sight for O(5+) in polar coronal holes above 2 solar radii from sun center and smaller such speeds for H(0) and protons. Doppler dimming and pumping diagnostics indicated that O(5+) and H(0) I reached supersonic outflow velocities within 2 solar radii. The observations appeared to be consistent with O95+) heating and direct momentum transfer by high frequency MHD waves through ion cyclotron resonance. Equatorial streamers were found to appear much different when observed in O VI, Fe XII and Mg X than when observed in H I Lyman-alpha or visible light. This led G. Noci to suggest that the elemental abundance of O, Fe, and Mg are lower in the dark center region of the O VI streamer image than it is in the brighter outer legs of the streamer. The O VI line ratio indicated a much smaller outflow speed in streamers than in the surrounding coronal holes. Spectroscopic observations of CME's in June and December 1996 showed large Doppler shifts indicating macroscopic flows of up to 200 km/s transverse to the apparent motion of the CME. The December event displayed factor of 500 intensity increases in H I Lyman lines and bright emissions in cool ion lines like C III 977 A indicating that the origin of some of the gas was a prominence. UVCS also observed two comets, several stars and interplanetary hydrogen. In the current reporting period, the initial results were published and detailed analyses including self consistent empirical models were developed. The research results were reported, published or submitted/accepted for publication. New observations were made to uncover additional information about the surprising results of the first year and other new observations revealed more surprises. A UVCS Tutorial was developed to familiarize potential users of UVCS data with the data products, analysis techniques and coronal models needed to analyze the data.

Kohl, John L.↗

NASA NTRS2004

Microlith Based Sorber for Removal of Environmental Contaminants

The development of energy efficient, lightweight sorption systems for removal of environmental contaminants in space flight applications is an area of continuing interest to NASA. The current CO2 removal system on the International Space Station employs two pellet bed canisters of 5A molecular sieve that alternate between regeneration and sorption. A separate disposable charcoal bed removes trace contaminants. An alternative technology has been demonstrated using a sorption bed consisting of metal meshes coated with a sorbent, trademarked and patented as Microlith by Precision Combustion, Inc. (PCI); thesemeshes have the potential for direct electrical heating for this application. This allows the bed to be regenerable via resistive heating and offers the potential for shorter regeneration times, reduced power requirement, and net energy savings vs. conventional systems. The capability of removing both CO2 and trace contaminants within the same bed has also been demonstrated. Thus, the need for a separate trace contaminant unit is eliminated resulting in an opportunity for significant weight savings. Unlike the charcoal bed, zeolites for trace contaminant removal are amenable to periodic regeneration. This paper describes the design and performance of a prototype sorber device for simultaneous CO2 and trace contarninant removal and its attendant weight and energy savings.

Roychoudhury, S.↗

NASA NTRS1979

Infrared Heaters

The heating units shown in the accompanying photos are Panelbloc infrared heaters, energy savers which burn little fuel in relation to their effective heat output. Produced by Bettcher Manufacturing Corporation, Cleveland, Ohio, Panelblocs are applicable to industrial or other facilities which have ceilings more than 12 feet high, such as those pictured: at left the Bare Hills Tennis Club, Baltimore, Maryland and at right, CVA Lincoln- Mercury, Gaithersburg, Maryland. The heaters are mounted high above the floor and they radiate infrared energy downward. Panelblocs do not waste energy by warming the surrounding air. Instead, they beam invisible heat rays directly to objects which absorb the radiation- people, floors, machinery and other plant equipment. All these objects in turn re-radiate the energy to the air. A key element in the Panelbloc design is a coating applied to the aluminized steel outer surface of the heater. This coating must be corrosion resistant at high temperatures and it must have high "emissivity"-the ability of a surface to emit radiant energy. The Bettcher company formerly used a porcelain coating, but it caused a production problem. Bettcher did not have the capability to apply the material in its own plant, so the heaters had to be shipped out of state for porcelainizing, which entailed extra cost. Bettcher sought a coating which could meet the specifications yet be applied in its own facilities. The company asked The Knowledge Availability Systems Center, Pittsburgh, Pennsylvania, a NASA Industrial Applications Center (IAC), for a search of NASA's files

Source record↗

NASA NTRS2007

Thermodynamic Vent System Performance Testing with Subcooled Liquid Methane and Gaseous Helium Pressurant

Due to its high specific impulse and favorable thermal properties for storage, liquid methane (LCH4) is being considered as a candidate propellant for exploration architectures. In order to gain an -understanding of any unique considerations involving micro-gravity pressure control with LCH4, testing was conducted at the Marshall Space Flight Center using the Multipurpose Hydrogen Test Bed (MHTB) to evaluate the performance of a spray-bar thermodynamic vent system (TVS) with subcooled LCH4 and gaseous helium (GHe) pressurant. Thirteen days of testing were performed in November 2006, with total tank heat leak conditions of about 715 W and 420 W at a fill level of approximately 90%. The TVS system was used to subcool the LCH4 to a liquid saturation pressure of approximately 55.2 kPa before the tank was pressurized with GHe to a total pressure of 165.5 kPa. A total of 23 TVS cycles were completed. The TVS successfully controlled the ullage pressure within a prescribed control band but did not maintain a stable liquid saturation pressure. This was likely. due to a TVS design not optimized for this particular propellant and test conditions, and possibly due to a large artificially induced heat input directly into the liquid. The capability to reduce liquid saturation pressure as well as maintain it within a prescribed control band, demonstrated that the TVS could be used to seek and maintain a desired liquid inlet temperature for an engine (at a cost of propellant lost through the TVS vent). One special test was conducted at the conclusion of the planned test activities. Reduction of the tank ullage pressure by opening the Joule-Thomson valve (JT) without operating the pump was attempted. The JT remained open for over 9300 seconds, resulting in an ullage pressure reduction of 30 kPa. The special test demonstrated the feasibility of using the JT valve for limited ullage pressure reduction in the event of a pump failure.

Flachbart, R. H.↗

NASA NTRS2012

Solar Spectral Irradiance and Climate

Spectrally resolved solar irradiance is recognized as being increasingly important to improving our understanding of the manner in which the Sun influences climate. There is strong empirical evidence linking total solar irradiance to surface temperature trends - even though the Sun has likely made only a small contribution to the last half-century's global temperature anomaly - but the amplitudes cannot be explained by direct solar heating alone. The wavelength and height dependence of solar radiation deposition, for example, ozone absorption in the stratosphere, absorption in the ocean mixed layer, and water vapor absorption in the lower troposphere, contribute to the "top-down" and "bottom-up" mechanisms that have been proposed as possible amplifiers of the solar signal. New observations and models of solar spectral irradiance are needed to study these processes and to quantify their impacts on climate. Some of the most recent observations of solar spectral variability from the mid-ultraviolet to the near-infrared have revealed some unexpected behavior that was not anticipated prior to their measurement, based on an understanding from model reconstructions. The atmospheric response to the observed spectral variability, as quantified in climate model simulations, have revealed similarly surprising and in some cases, conflicting results. This talk will provide an overview on the state of our understanding of the spectrally resolved solar irradiance, its variability over many time scales, potential climate impacts, and finally, a discussion on what is required for improving our understanding of Sun-climate connections, including a look forward to future observations.

Pilewskie, P.↗

NASA NTRSDate not supplied

Establishing the Feasibility of the Centrifugal Nuclear Thermal Rocket

The Centrifugal Nuclear Thermal Rocket (CNTR) is a Nuclear Thermal Propulsion (NTP) concept designed to heat propellant directly by the reactor fuel. The primary difference between the CNTR concept and traditional NTP systems is that rather than using traditional solid fuel elements, the CNTR uses liquid fuel with the liquid contained in rotating cylinders by centrifugal force. If the concept can be successfully realized, the CNTR would have a high specific impulse (~1800 s) at high thrust, which may enable viable near-term human Mars exploration by reducing round-trip times to ~420 days. The CNTR could also use storable propellants such as ammonia, methane, or hydrazine at an Isp of ~900 s, enabling long-term in-space storage of a dormant system. Significant engineering challenges must be addressed to establish the technical viability of the CNTR, and the plan for addressing these engineering challenges is the subject of this paper.

Dale Thomas↗

NASA NTRSDate not supplied

Using Thermal Desktop to Determine Equivalent Solar Hours on Spacecraft Surfaces

Equivalent solar hours (ESH) are the duration of exposure of a surface to solar radiation, particularly ultraviolet (UV) radiation. Since UV light causes degradation to optical properties of thermal control surfaces, the determination of ESH is important to calculate end of life (EOL) optical properties for spacecraft external surfaces. A higher ESH value generally correlates to greater UV degradation experienced by the surface, resulting in an increase in solar absorptivity. This paper details a novel approach for calculating ESH using Thermal Desktop. Since the ESH value is useful for thermal analysts, this technique is beneficial to quickly perform the analysis internally with tools readily available without relying on external support and funding. The example presented in this paper shows how this method was developed and used for NASA's lunar Gateway spacecraft. This method of analysis is used to calculate ESH for the transit, assembly in orbit, and operational phases for Gateway, utilizing each of the program’s planned configurations throughout its 15-year lifetime. ESH values were calculated using the Monte-Carlo ray tracing capability of Thermal Desktop using both direct solar heating and indirect solar heating due to reflections from other surfaces. The output of this analysis includes an ESH gradient map across the spacecraft. Post-processing of these results enabled identification of the average and maximum ESH on critical surfaces such as radiators. The final ESH values for each surface are then used for determination of EOL optical properties.

Thermal Control↗

NASA NTRS2026

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

This paper highlights one aspect of NASA’s ongoing technology-infusion effort to design, fabricate, and test a next-generation outer shell fabric for a lunar Extravehicular Activity (EVA) space suit, a critical component of sustained lunar exploration. Managing thermal loads on the Moon is essential for astronaut safety and suit performance. The suit’s exterior fabric directly influences heat gain and loss through its optical properties: low solar absorptivity minimizes sunlight absorption, while high infrared emissivity aids radiative cooling. Lunar regolith complicates this balance. Its fine, abrasive particles possess unique optical behavior that can lower reflectivity and raise emissivity when embedded in or adhered to fabric surfaces, degrading thermal control and increasing the risk of overheating or cooling inefficiency. To quantify these effects, the Artemis Suit Materials (ASM) team measured solar absorptance and infrared emissivity of clean and dust-soiled Ortho Fabric, establishing beginning-of-life (BOL) and end-of-life (EOL) benchmarks. EOL conditions were simulated with a rotary tumbler abrasion process using lunar dust simulant and ceramic media to reproduce cumulative wear expected during surface operations. Tests also included unmodified fabrics and a fabric/film laminate system containing titanium dioxide to evaluate potential improvements in dust resistance and optical performance. Results from these evaluations provide critical insight into how lunar dust alters fabric thermal behavior and inform the design of bespoke suit materials that maintain required optical properties throughout mission life, supporting safe and effective long-duration EVA on the lunar surface.

space↗

NASA NTRS2026

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

Textile↗

NASA NTRS1987

Effect of heat treatment on the fracture behaviour of directionally solidified (gamma/gamma-prime)-alpha alloy

An investigation is conducted into the influence of various heat treatments on the work of fracture and its relation to microstructure for a directionally solidified Ni-33Mo-5.7Al (wt pct) (gamma/gamma-prime)-alpha alloy. The jagged crack propagation observed is due to delamination of the ligaments and associated plastic deformation. Fracture behavior is examined with respect to alloy microstructures and load-deflection curves. The four heat-treatment conditions considered are: (1) as-directionally solidified, (2) solutionized, (3) directionally solidified and thermally cycled, and (4) solutionized and thermally cycled.

Sriramamurthy, A. M.↗

NASA NTRS1999

Microwave Induced Direct Bonding of Single Crystal Silicon Wafers

We have heated polished doped single-crystal silicon wafers in a single mode microwave cavity to temperatures where surface to surface bonding occurred. The absorption of microwaves and heating of the wafers is attributed to the inclusion of n-type or p-type impurities into these substrates. A cylindrical cavity TM (sub 010) standing wave mode was used to irradiate samples of various geometry's at positions of high magnetic field. This process was conducted in vacuum to exclude plasma effects. This initial study suggests that the inclusion of impurities in single crystal silicon significantly improved its microwave absorption (loss factor) to a point where heating silicon wafers directly can be accomplished in minimal time. Bonding of these substrates, however, occurs only at points of intimate surface to surface contact. The inclusion of a thin metallic layer on the surfaces enhances the bonding process.

Budraa, N. K.↗

NASA NTRS1996

Determination of Highly Accurate Heats of Formation

Two approaches for directly computing a molecular heat of formation based on sophisticated ab initio electronic structure theory axe discussed and example calculations are presented for several molecules of interest in atmospheric chemistry including HNO and CICN. The accuracy of these approaches for a small subset of the molecules is demonstrated by comparison to very accurate experimental data. A third approach for evaluating accurate heats of formation consists of combining experimental and theoretical data. The potential for this method to provide reliable thermochemical data on many molecules using accurate experimental beats of formation for only a small number of species is demonstrated by giving accurate (Delta)H(sup 0, sub f) quantities for a host of fluorine, chlorine, and bromine oxide and nitrogen oxide compounds. Potential pitfalls in all three approaches are discussed.

Lee, Timothy J.↗

NASA NTRS1993

Thermal Protection System design studies for lunar crew module

The results of a study to predict aeroheating and Thermal Protection System (TPS) requirements for manned entry vehicles returning to Earth from the moon are presented. The effects of vehicle size and lunar-return strategies on the aerothermodynamic environment and TPS design were assessed. Study guidelines were based on an Apollo Command Module (CM) configuration and lunar return strategies included direct entry and aerocapture followed by Low Earth Orbit entry (LEO). Convective heating was obtained by the boundary layer integral matrix procedure (BLIMP) code, and radiative heating was computed with the QRAD program. The AESOP-STAB code and the AESOP-THERM code were used for TPS analysis for ablating materials and nonablating materials respectively. Results indicated that there was an optimum size for minimum heating and that direct entry had higher heating rates than aerocapture. Aerocapture resulted in higher heat loads and TPS weight. The TPS weight factor was 6-8 percent for all lunar return strategies, with the TPS weight being about 50 percent less than that of the original Apollo CM vehicle.

Williams, S. D.↗

NASA NTRS1982

Heat flow control and segregation in directional solidification

Optimization of the vertical Bridgman technique for growth of electronic materials in single crystal form was investigated. The limitations of the crystal growth configuration were experimentally determined and heat transfer related deficiencies identified. Design of an alternate system was based on the use of heat pipes separated by a gradient region. Heat transfer analyses based on one and two dimensional models indicated the necessity of a flexible gradient zone configuration. Directional melting of binary systems as encountered during seeding in melt growth was analysed for concurrent compositional changes at the crystal-metal interface, and the theoretical treatment numerically applied to HgCdTe and Ga doped germanium. A theoretical and experimental study of the thermal effects associated with current flow was conducted. It was found that experimental measurements of dc induced growth during crystal pulling can be used for the precise determination of the Peltier coefficient.

Witt, A. F.↗

NASA NTRS1974

Structural heat pipe

A combined structural reinforcing element and heat transfer member is disclosed for placement between a structural wall and an outer insulation blanket. The element comprises a heat pipe, one side of which supports the outer insulation blanket, the opposite side of which is connected to the structural wall. Heat penetrating through the outer insulation blanket directly reaches the heat pipe and is drawn off, thereby reducing thermal gradients in the structural wall. The element, due to its attachment to the structural wall, further functions as a reinforcing member.

Ollendorf, S.↗