Results for “electricity use” — Page 16

DOE OSTI2024

A Novel Dew Point Meter: Application to the Measurement of the Sulfuric Acid Dew Point for Combustion Flue Gas

Accurate knowledge of acid dew point is essential for industrial and applied combustion applications. Sulfur in the fuel or raw materials is converted to sulfur dioxide (SO2) during combustion, and a portion of the SO2 is oxidized to sulfur trioxide (SO3). The SO3 will react to form H2SO4 vapor when in the presence of water vapor. Even with just trace levels of H2SO4 vapor in the gas phase (1-10 ppm), the dew point can reach 100°C and higher. To avoid acid condensation and the resulting corrosion on heat recovery equipment, plant engineers must ensure that surface temperatures are above the acid dew point, but this decreases the efficiency of thermal energy recovery. Thus, there is a trade-off between minimizing equipment corrosion and maximizing thermal energy recovery, and the acid dew point is a key parameter for this optimization. Commercially available acid dew point meters use electric conductivity sensors. These sensors are known to greatly underestimate the dew point due to their low sensitivity. In addition, no validation testing has been reported for these units and they are often expensive. In this work, we analyze the theory of the sulfuric acid condensation and develop a novel dew point meter based on this analysis. The meter consists of a novel optical instrument that is designed to monitor the slightest appearance of condensation on a hydrophobic window surface as the surface temperature of the window is slowly decreased. In this way, an accurate measurement of the dew point is obtained under a wide range of concentrations. The basis of the instrument is that a collimated beam from a diode laser will generate forward scattered light when the beam encounters surface condensate, and a sophisticated array detector is used to sensitively monitor the onset of light scattering. The measurement procedures are established to rapidly find the acid dew point, while minimizing error. Further, to calibrate the dew point meter we developed a calibration system based on a liquid bubbler that can generate a stable gas flow with a known sulfuric acid dew point. Test results show that the dew point meter can accurately measure acid dew point over a wide range. For H2SO4 vapor concentrations as low as 6 ppm the acid dew point is measured with an error of only ~1°C. To demonstrate the versatility of this instrument, the dew point meter was adapted for use with a high-pressure flow cell to allow for measurements of the dew point of flue gas from pressurized oxy-fuel combustion in a 100 kWth pressurized reactor.

Cheng, Mao↗

DOE OSTI2022

ATR Fuel Management

The sixth Core Internals Changeout (CIC) of ATR was completed on March 21, 2022, and Nuclear Testing (NT) commenced shortly thereafter. In support of NT, 235U flux wires were attached to flux wands using electrical tape and installed in water channels 2, 6, 11, 15 and 19 in each of the 40 ATR Mark VII fuel elements that comprise an ATR core to perform low power flux measurements during ATR Cycle 170CIC NT-3. The flux wands were fabricated from Poly (Methyl Methacrylate), or PMMA. Irradiated cobalt capsules were loaded in the ATR Northeast Irradiation Housing Assembly (NEIHA), the East Flux Trap (EFT), South Flux Trap (SFT), inboard A-positions and various H-positions as a 170CIC NT-3 core reactivity hold-down mechanism. The PMMA flux wands received significant gamma dose from the irradiated cobalt during NT-3 which caused discoloration, embrittlement and swelling of the flux wands. The removal of the degraded flux wands from the 0.078 in. wide by 50 in. long fuel element coolant channels has been a unique challenge. This presentation summarizes the cleaning techniques used to remove the flux wand debris from the elements, an aggressive PMMA irradiation experiment performed concomitantly with initial cleaning efforts, and planned inspection and qualification techniques that will be applied in the future to potentially requalify the impacted elements for re-use.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Data-Driven Optimization of the Processing Window for 316H Components Fabricated Using Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development and deployment of advanced materials and components fabricated via additive manufacturing with a specific focus on laser powder bed fusion (LPBF). As an initial case study, the program has selected 316H stainless steel (SS) as an initial material around which to develop a code case development strategy. This strategy involves two parallel approaches: (1) an equivalency approach whereby round-robin testing across multiple collaborating laboratories demonstrates repeatability in processing and direct comparisons with conventional wrought 316H material and (2) a revolutionary approach to code qualification combining in situ data collection and high-fidelity modeling to capture, predict, and bound the performance of LPBF 316HSS components. As part of this campaign, this work package has initiated an extensive process optimization campaign across three laboratories, each printing variations of LPBF 316HSS using three different LPBF units (Concept Laser, EOS, and Renishaw). In FY23, ORNL has focused on unique experimental designs spanning wide ranges in energy inputs and turning knobs such as scan speed, laser power, hatch spacing, layer thickness, spot size, scan rotation, and more. On the Concept Laser M2, 72 different combinations of processing variables were investigated with duplicate samples and different powder compositions. In total, 252 samples were printed with combined in situ sensing data. A parallel design of experiments was conducted on the Renishaw AM400 with an additional 390 printed specimens for analysis. All 642 miniature specimens, each with unique features included in each print to capture geometry-related heterogeneity, were subjected to high-throughput x-ray computed tomography (XCT) analysis to enable the downselection of specific processing parameters of interest. Then, using electrical discharge machining (EDM), miniature tensile specimens were extracted for mechanical testing and microscopy investigations. From the analysis performed in FY23, it was found that powder composition drastically affects the resulting microstructure and mechanical performance of 316SS. Specifically, changing from 316L to 316HSS powder results in a wide range of grain sizes with varying degrees of preferred grain orientation, which increases as a function of energy density. It was also found that due to stored heat in thin fin–type features, large microstructural differences can be seen within one part printed with one set of processing parameters. These variations in microstructure features, including grain size, the nanoscale dislocation structure, and grain texture, will all affect the irradiation performance and high-temperature mechanical performance of LPBF 316HSS parts. Two sets of concept laser processing parameters, spanning both refined and columnar grain structures, were scaled to print larger 316H builds for campaign testing (high-temperature creep and irradiation). In addition, at least two optimized processing parameter sets were identified for the Renishaw AM400 for round-robin testing in FY24 with Argonne National Laboratory. Future work includes printing samples using identical parameters identified by partner institutions, providing material for corrosion and high-temperature mechanical testing, and continuing evaluations of heterogeneity in larger printed parts.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Data-Driven Optimization of the Processing Window for 316H Components Fabricated Using Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development and deployment of advanced materials and components fabricated via additive manufacturing with a specific focus on laser powder bed fusion (LPBF). As an initial case study, the program has selected 316H stainless steel (SS) as an initial material around which to develop a code case development strategy. This strategy involves two parallel approaches: (1) an equivalency approach whereby round-robin testing across multiple collaborating laboratories demonstrates repeatability in processing and direct comparisons with conventional wrought 316H material and (2) a revolutionary approach to code qualification combining in situ data collection and high-fidelity modeling to capture, predict, and bound the performance of LPBF 316HSS components. As part of this campaign, this work package has initiated an extensive process optimization campaign across three laboratories, each printing variations of LPBF 316HSS using three different LPBF units (Concept Laser, EOS, and Renishaw). In FY23, ORNL has focused on unique experimental designs spanning wide ranges in energy inputs and turning knobs such as scan speed, laser power, hatch spacing, layer thickness, spot size, scan rotation, and more. On the Concept Laser M2, 72 different combinations of processing variables were investigated with duplicate samples and different powder compositions. In total, 252 samples were printed with combined in situ sensing data. A parallel design of experiments was conducted on the Renishaw AM400 with an additional 390 printed specimens for analysis. All 642 miniature specimens, each with unique features included in each print to capture geometry-related heterogeneity, were subjected to high-throughput x-ray computed tomography (XCT) analysis to enable the downselection of specific processing parameters of interest. Then, using electrical discharge machining (EDM), miniature tensile specimens were extracted for mechanical testing and microscopy investigations. From the analysis performed in FY23, it was found that powder composition drastically affects the resulting microstructure and mechanical performance of 316SS. Specifically, changing from 316L to 316HSS powder results in a wide range of grain sizes with varying degrees of preferred grain orientation, which increases as a function of energy density. It was also found that due to stored heat in thin fin–type features, large microstructural differences can be seen within one part printed with one set of processing parameters. These variations in microstructure features, including grain size, the nanoscale dislocation structure, and grain texture, will all affect the irradiation performance and high-temperature mechanical performance of LPBF 316HSS parts. Two sets of concept laser processing parameters, spanning both refined and columnar grain structures, were scaled to print larger 316H builds for campaign testing (high-temperature creep and irradiation). In addition, at least two optimized processing parameter sets were identified for the Renishaw AM400 for round-robin testing in FY24 with Argonne National Laboratory. Future work includes printing samples using identical parameters identified by partner institutions, providing material for corrosion and high-temperature mechanical testing, and continuing evaluations of heterogeneity in larger printed parts.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Reaction mechanisms for electrical doping of organic semiconductors using complex dopants

Electrical doping of organic semiconductors (OSCs) can be achieved using simple one-electron reductants and oxidants as n- and p-dopants, respectively, but for such dopants, increased doping strength is accompanied by increased sensitivity to ambient moisture and/or oxygen. “Indirect” or “complex” dopants—defined here as those that generate OSC radical cations or anions via pathways more complex than a single simple electron transfer, i.e., by multistep reactions—represent a means of circumventing this problem. Further, this review highlights the importance of understanding the reaction mechanisms by which such dopants operate for: (i) ensuring a researcher knows the composition of a doped material; (ii) predicting the thermodynamic feasibility of achieving doping with related dopant:OSC combinations; and (iii) predicting whether thermodynamically feasible doping reactions are likely to be rapid or slow, or to require subsequent activation. The mechanistic information available to date for some of the wide variety of complex n- and p-dopants that have been reported is then reviewed, emphasizing that in many cases our knowledge is far from complete.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Characterization of fluid inside pipe using multi frequency electrical signal

A multi-frequency signal may be used to induce voltage difference across a portion of a pipe. The voltage difference may be induced to take multi-frequency measurement of impedance characteristics of fluid inside the pipe. The multi-frequency measurement of the impedance characteristic of the fluid inside the pipe may be used to determine a characteristic of the fluid inside the pipe. This may be achieved by active integration of experimental data with high-resolution multi-frequency electrical impedance tomography (MFEIT) modeling.

Chillara, Vamshi Krishna↗

DOE OSTI2022

Evaluating the demand response potential of ammonia plants

Demand-side management/demand response (DSM/DR) are key strategies for mitigating the inherent variability in electricity generation rates by renewable sources. This article represents—to our knowledge—the first foray into assessing the DR potential of ammonia plants. Ammonia plants are interesting candidates for DR initiatives because of their significant electricity use (for operating compressors driving the synthesis loop) and the ability to store the ammonia product relatively easily and safely. Our approach is based on formulating and solving an optimal DR scheduling problem for an ammonia plant while accounting for the process dynamics. To this end, we introduce a new Hammerstein–Wiener-inspired modeling framework based on injecting linear dynamics in a first-principles static nonlinear model of the process. The results are encouraging; for the cases considered, peak-time power consumption decreases between 3.57% and 7.40%, coupled with 1.39% to 3.70% reductions in operating cost.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Covalent Organic Framework (COF) Derived Ni–N–C Catalysts for Electrochemical CO 2 Reduction: Unraveling Fundamental Kinetic and Structural Parameters of the Active Sites

Electrochemical CO 2 reduction is a potential approach to convert CO 2 into valuable chemicals using electricity as feedstock. Abundant and affordable catalyst materials are needed to upscale this process in a sustainable manner. Nickel-nitrogen-doped carbon (Ni-N-C) is an efficient catalyst for CO 2 reduction to CO, and the single-site Ni-N x motif is believed to be the active site. However, critical metrics for its catalytic activity, such as active site density and intrinsic turnover frequency, so far lack systematic discussion. In this work, we prepared a set of covalent organic framework (COF)-derived Ni-N-C catalysts, for which the Ni-N x content could be adjusted by the pyrolysis temperature. The combination of high-angle annular dark-field scanning transmission electron microscopy and extended X-ray absorption fine structure evidenced the presence of Ni single-sites, and quantitative X-ray photoemission addressed the relation between active site density and turnover frequency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Ion separations with membranes

Ion separations are important for resource recovery, water treatment, and energy production and storage. Techniques such as chemical precipitation, selective adsorption, and solvent extraction are effective, but membranes may separate ions continuously with less waste and lower energy costs. Separation of monovalent and multivalent ions with nanofiltration or electrodialysis membranes already enables water softening and edible salt purification. Similar membranes are attractive as separators in vanadium redox flow batteries. Selective partitioning of divalent counter-ions into ion-exchange membranes even allows transport of these ions against their concentration gradients in salt mixtures. However, separations of ions with the same charge is more challenging. Recent research demonstrated highly selective ion “sieving” at small scales. Here, separations using electrical potentials and differences in ion electrophoretic mobilities are promising, but relatively unexplored. Carrier-mediated transport affords high selectivity in liquid membranes, but these systems are not very stable, and selective transport via hopping between anchored carriers has proven elusive. Finally, this paper discusses how concentration polarization decreases selectivities in many membrane processes. Although development of selective, inexpensive ion-separation membranes is a work in progress, successes in water softening and edible salt purification suggests that future selective membranes will serve as complementary methods to traditional purification techniques.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Generation and representation of synthetic smart meter data

Advanced energy algorithms running at big-data scale will be necessary to identify, realize, and verify energy savings to meet government and utility goals of building energy efficiency. Any algorithm must be well characterized and validated before it is trusted to run at these scales. Smart meter data from real buildings will ultimately be required for the development, testing, and validation of these energy algorithms and processes. However, for initial development and testing, smart meter data are difficult to work with due to privacy restrictions, noise from unknown sources, data accessibility, and other concerns which can complicate algorithm development and validation. This paper describes a new methodology to generate synthetic smart meter data of electricity use in buildings using detailed building energy modeling, which aims to capture the variability and stochastics of real energy use in buildings. The methodology can create datasets tailored to represent specific scenarios with known truth and controllable amounts of synthetic noise. Knowledge of ground truth also allows the development and validation of enhanced processes which leverage building metadata, such as building type or size (floor area), in addition to smart meter data. The methodology described in this paper includes the key influencing factors of real-world building energy use including weather data, occupant-driven loads, building operation and maintenance practices, and special events. Data formats to support workflows leveraging both synthetic meter data and associated metadata are proposed and discussed. Finally, example use cases of the synthetic meter data are described to illustrate potential applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Simulating dispatchable grid services provided by flexible building loads: State of the art and needed building energy modeling improvements

End-use electrical loads in residential and commercial buildings are evolving into flexible and cost-effective resources to improve electric grid reliability, reduce costs, and support increased hosting of distributed renewable generation. This article reviews the simulation of utility services delivered by buildings for the purpose of electric grid operational modeling. We consider services delivered to (1) the high-voltage bulk power system through the coordinated action of many, distributed building loads working together, and (2) targeted support provided to the operation of low-voltage electric distribution grids. Although an exhaustive exploration is not possible, we emphasize the ancillary services and voltage management buildings can provide and summarize the gaps in our ability to simulate them with traditional building energy modeling (BEM) tools, suggesting pathways for future research and development.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

Evaluating the energy impact potential of energy efficiency measures for retrofit applications: A case study with U.S. medium office buildings

Quantifying the energy savings of various energy efficiency measures (EEMs) for an energy retrofit project often necessitates an energy audit and detailed whole building energy modeling to evaluate the EEMs; however, this is often cost-prohibitive for small and medium buildings. In order to provide a defined guideline for projects with assumed common baseline characteristics, this paper applies a sensitivity analysis method to evaluate the impact of individual EEMs and groups these into packages to produce deep energy savings for a sample prototype medium office building across 15 climate zones in the United States. We start with one baseline model for each climate zone and nine candidate EEMs with a range of efficiency levels for each EEM. Three energy performance indicators (EPIs) are defined, which are annual electricity use intensity, annual natural gas use intensity, and annual energy cost. Then, a Standard Regression Coefficient (SRC) sensitivity analysis method is applied to determine the sensitivity of each EEM with respect to the three EPIs, and the relative sensitivity of all EEMs are calculated to evaluate their energy impacts. For the selected range of efficiency levels, the results indicate that the EEMs with higher energy impacts (i.e., higher sensitivity) in most climate zones are high-performance windows, reduced interior lighting power, and reduced interior plug and process loads. However, the sensitivity of the EEMs also vary by climate zone and EPI; for example, improved opaque envelope insulation and efficiency of cooling and heating systems are found to have a high energy impact in cold and hot climates.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Chapter 3 - Harvesting Thermal Energy with Ferroelectric Materials

Thermal energy is considered the ubiquitous form of energy as all other forms of energy ultimately degrade to thermal energy. Thermal to electrical energy conversion is currently an important method for electricity generation. The traditional power cycles, however, become technically and economically unviable when heat source temperature reduces below 100 °C. Thermal energy harvesting has been proposed as a viable alternative for low-grade thermal to electrical energy conversion. Thermal energy harvesting is a method of generating electricity using temperature-induced variations in material properties. It is particularly useful when the heat sources are available free-of-cost, either in the form of natural heat or waste heat. While there are several thermal energy harvesting techniques, pyroelectricity is the most promising as it can be used in situations where spatial thermal gradients are difficult to establish or the temperature of the heat source is changing. Despite the fact that the pyroelectric effect in ferroelectric materials has been known for past several decades, thermal energy harvesting using ferroelectric materials has not been much explored in the literature. In this chapter, we would explore various aspects of thermal energy harvesting using ferroelectric materials. We have first established the physics behind ferroelectricity, then provided a detailed description on ferroelectric thermal energy harvesting, discussed various ferroelectric thermodynamic cycles and devices proposed in the literature, and finally described various other emerging applications of ferroelectricity.

DIRECT ENERGY CONVERSION,MATERIALS SCIENCE,OTHER I↗

DOE OSTI2022

Network Optimization of the Electrosynthesis of Chemicals from CO2

Carbon dioxide electroreduction (ECO2R) is gaining attention due to its capacity to mitigate CO2 emissions while using electricity that would otherwise be curtailed. Its foreseeable industrial implementation requires of holistic methods to assess the technological and economic performance of ECO2R processes and integrate them in current chemical supply chains and power systems. Here, we combine techno-economic assessment and mathematical programming to find the optimal paths to electroreduce CO2 into valuable chemicals under variable electricity prices. The proposed approach is tested with a case study addressing the CO2 capture from flue gas or direct air and its electricity-powered reduction into carbon monoxide, formic acid or multi-carbon compounds. The results obtained demonstrate the ability of the framework to build ECO2R networks and provide operation profiles that respond to fluctuating electricity prices.

carbon dioxide↗

DOE OSTI2020

An encoder–decoder LSTM-based EMPC framework applied to a building HVAC system

Numerous studies have demonstrated the benefit of economic model predictive control (EMPC) applied to building heating, ventilation, and air conditioning (HVAC) systems. However, the construction and training of predictive models for building HVAC systems are widely recognized as a key technological barrier preventing large-scale adoption of EMPC for buildings. In this work, an encoder–decoder long short-term memory-based EMPC framework is developed. The key advantage of the approach is that a model may be automatically generated from a list of inputs and outputs. From the definition of inputs and outputs, the constructed model may be trained and automatically embedded into the EMPC framework for real-time estimation and control. The overall end-to-end EMPC framework from model training to on-line estimation and control are described. To this end, the encoder–decoder model provides a natural framework for state estimation (encoder), which is required to provide an initial condition for the predictive model of EMPC (decoder). Closed-loop simulations using EnergyPlus are performed to demonstrate the approach. The simulated closed-loop system consists of a building zone from a multi-zone building, which is served by an air handling unit-variable air volume HVAC system. For the HVAC example considered, the trained encoder–decoder model can predict the indoor air temperature and HVAC sensible cooling rate of a building zone over a two-day horizon with high accuracy. Overall, we find that considering a time-of-use electric rate structure, the EMPC, which manipulates the zone temperature setpoint, can reduce the HVAC power consumption cost relative to keeping the zone temperature setpoint at its maximum value (i.e., minimum energy approach).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

Potential benefits and optimization of cool-coated office buildings: A case study in Chongqing, China

Increasing envelope facet albedos considerably reduces solar heat gain, thus yielding building cooling energy savings. Few studies have explored the potential benefits of utilizing cool coatings on building envelopes (“cool-coated buildings”) based on life-cycle cost analysis. A holistic approach integrating the field testing, building energy simulation, and a 20-year life-cycle-based optimization was developed to explore cool-coated building performance and the maximum net savings of optimal building envelope retrofit and design. Experimental results showed that applying cool coatings to a west wall of an office building in Chongqing, China reduced its exterior surface temperature by up to 9.3 °C in summer. Additionally, simulation results showed that in Chongqing, making the roof and walls cool could reduce annual HVAC electricity use by up to 11.9% in old buildings (with poorly insulated envelopes) and up to 5.9% in new buildings. Retrofitting old buildings with a cool roof provided the net savings per modified area with present values up to 42.8 CNY/m2; retrofitting a new building with a cool roof or cool walls was not cost-effective. Optimizing both envelope insulation and envelope albedo can achieve 5.6 times the net savings of optimizing the insulation only, and 1.6 times that of optimizing albedo only.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Dirty dishes or dirty laundry? Comparing two methods for quantifying American consumers' preferences for load management in a smart home

One challenge of transitioning to renewable energy is that household electricity use and renewable generation are often misaligned. Smart home energy management systems hold promise for shifting usage to match generation, but these systems need to be designed with the occupants’ preferences in mind. The purpose of the present research is to compare two approaches for collecting and modeling consumers’ load management preferences, both of which are amenable to use in a home energy management system. Specifically, we examine the performance of Simple Multi-Attribute Rating Technique Exploiting Ranks (SMARTER) and Analytic Hierarchy Process (AHP) in quantifying consumers’ preferences regarding air temperature (air conditioning and heating), water heating, dishwashing, clothes washing and drying, monetary costs, environmental impacts, and comfort/convenience. Two studies are presented: Study 1 examines the SMARTER approach, and Study 2 focuses on the AHP approach. In both studies, online surveys (N SMARTER = 956 and N AHP = 1023) were conducted to elicit preferences from participants across the United States. The preferences modeled by both approaches were validated based on (a) their ability to predict participants’ choices in a Discrete Choice Experiment and (b) their convergence with previous research on load-shifting behavior. The validation procedure suggests that the SMARTER approach is superior in modeling consumers’ preferences for load management. Overall, this research lays the groundwork for designing a smart home interface capable of collecting occupants’ preferences and using those preferences to deliver improved occupant comfort, lower operating costs, reduced environmental impact, and more significant demand response than exists today.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

Densification, microstructure, and mechanical properties of Mo–30W alloys fabricated from conditioned powders

Refractory alloys, such as molybdenum-based systems, are attracting growing interest for applications in extreme environments, such as in the nuclear and aerospace industries. Recent advances in sintering technologies, coupled with mechanical alloying, have enabled the tailored design of these alloys by leveraging powder characteristics to control final microstructures and mechanical properties. In this study, Mo-30W alloys were fabricated using electric field-assisted sintering (EFAS) from ball-milled powders with and without hydrogen treatment to investigate the influence of surface oxides on material properties and sintering behavior. The results revealed that samples processed from as-ball-milled powder contained a high density of oxides within the microstructure, whereas oxide presence was significantly reduced in samples fabricated from hydrogen-treated powders. Interestingly, the two powder types led to opposite trends in grain size distribution: samples from untreated powders exhibited grain refinement from sample periphery to the center, while samples from hydrogen-treated powders showed grain coarsening toward the center. This behavior is attributed to temperature gradients present during sintering due to electrical percolation pathway differences during Joule heating. The powder surface oxides may have influenced the temperature distribution and grain evolution. Microhardness profiles measured along both axial and thickness directions were consistent with the grain size distribution. Furthermore, oxide films on powder surfaces have delayed densification by hindering particle necking and atomic diffusion during sintering.

36 - MATERIALS SCIENCE↗