Search NASA⌕ Search

SEARCH · Search NASA

Results for “moisture content”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Utilizing Calibrated GPS Reflected Signals to Estimate Soil Reflectivity and Dielectric Constant: Results from SMEX02

Extensive reflected GPS data was collected using a GPS reflectometer installed on an HC130 aircraft during the Soil Moisture Experiment 2002 (SMEX02) near Ames, Iowa. At the same time, widespread surface truth data was acquired in the form of point soil moisture profiles, areal sampling of near-surface soil moisture, total green biomass and precipitation history, among others. Previously, there have been no reported efforts to calibrate reflected GPS data sets acquired over land. This paper reports the results of two approaches to calibration of the data that yield consistent results. It is shown that estimating the strength of the reflected signals by either (1) assuming an approximately specular surface reflection or (2) inferring the surface slope probability density and associated normalization constants give essentially the same results for the conditions encountered in SMEX02. The corrected data is converted to surface reflectivity and then to dielectric constant as a test of the calibration approaches. Utilizing the extensive in-situ soil moisture related data this paper also presents the results of comparing the GPS-inferred relative dielectric constant with the Wang-Schmugge model frequently used to relate volume moisture content to dielectric constant. It is shown that the calibrated GPS reflectivity estimates follow the expected dependence of permittivity with volume moisture, but with the following qualification: The soil moisture value governing the reflectivity appears to come from only the top 1-2 centimeters of soil, a result consistent with results found for other microwave techniques operating at L-band. Nevertheless, the experimentally derived dielectric constant is generally lower than predicted. Possible explanations are presented to explain this result.

Katzberg, Stephen J.↗
NASA NTRS1984

Estimating net rainfall, evaporation and water storage of a bare soil from sequential L-band emissivities

A general method to use a time series of L-band emissivities as an input to a hydrological model for continuously monitoring the net rainfall and evaporation as well as the water content over the entire soil profile is proposed. The model requires a sufficiently accurate and general relation between soil emissivity and surface moisture content. A model which requires the soil hydraulic properties as an additional input, but does not need any weather data was developed. The method is shown to be numerically consistent.

Stroosnijder, L.↗
NASA NTRS1983

Monte Carlo simulation of the effect of soil moisture variation on the microwave emission from soils

In this paper, results of a Monte Carlo simulation of the effect of noise on the relationship between the microwave emissivity of soil and its moisture content are presented. It is found that whenever the magnitude of the noise for the independent variable, in this case the soil moisture, is increased, both the slope of the regression and the correlation coefficient decrease. In particular, when the noise has magnitude equivalent to a coefficient of variation of 0.25, the slope and correlation coefficient are in good agreement with those obtained from the data of a 21-cm airborne microwave radiometer which was flown over a test site in hand county, South Dakota. The comparison was made using a linear relationship to determine the estimated emissivity from the ground measurements of soil moisture. The linear relationship was derived from a radiative transfer model calculation of the microwave emissivities using realistic soil-moisture profiles. The effect of surface roughness was included in the relationship, and the variability of the surface roughness was also simulated by a Monte Carlo technique.

Mo, T.↗
NASA NTRS1980

Joint microwave and infrared studies for soil moisture determination

The feasibility of using a combined microwave-thermal infrared system to determine soil moisture content is addressed. Of particular concern are bare soils. The theoretical basis for microwave emission from soils and the transport of heat and moisture in soils is presented. Also, a description is given of the results of two field experiments held during vernal months in the San Joaquin Valley of California.

Njoku, E. G.↗
NASA NTRS2004

Radar for Measuring Soil Moisture Under Vegetation

A two-frequency, polarimetric, spaceborne synthetic-aperture radar (SAR) system has been proposed for measuring the moisture content of soil as a function of depth, even in the presence of overlying vegetation. These measurements are needed because data on soil moisture under vegetation canopies are not available now and are necessary for completing mathematical models of global energy and water balance with major implications for global variations in weather and climate.

Moghaddam, Mahta↗
NASA NTRS1976

Monitoring wheat growth with radar

The scattering properties of wheat in the 8-18 GHz band were studied as a function of frequency, polarization, incidence angle, and crop maturity. Supporting ground truth was collected at the time of measurement. The data indicate the radar backscattering coefficient is sensitive to both radar system parameters and crop characteristics, particularly at incidence angles near nadir. Linear regression analysis of the backscattering coefficient (dB) on both time and plant moisture content result in rather good correlation, as high as 0.9, with the slope of these regression lines being 0.55 dB/day and -0.275 dB% plant moisture at 9.4 GHz at nadir. It is found that the coefficient undergoes rapid variations shortly before and after the wheat is harvested. Both of these analyses suggest methods for estimating wheat maturity and for monitoring the progress of harvest.

Bush, T. F.↗
NASA NTRS1984

Surface-Moisture Monitoring Technique

Technique monitors drying of continuous sheets of thin material. Ribbon sensing element samples moisture content of web material during each rotation of roller. Change in resistivity of thermally and electrically conductive ribbon is parameter used to measure web moisture; measurements insensitive to ribbon contact pressure. Application in industrial production of sheet materials such as paper and fabric.

Yang, L. C.↗
NASA NTRS2016

Transitioning Enhanced Land Surface Initialization and Model Verification Capabilities to the Kenya Meteorological Department (KMD)

Flooding, severe weather, and drought are key forecasting challenges for the Kenya Meteorological Department (KMD), based in Nairobi, Kenya. Atmospheric processes leading to convection, excessive precipitation and/or prolonged drought can be strongly influenced by land cover, vegetation, and soil moisture content, especially during anomalous conditions and dry/wet seasonal transitions. It is thus important to represent accurately land surface state variables (green vegetation fraction, soil moisture, and soil temperature) in Numerical Weather Prediction (NWP) models. The NASA SERVIR and the Short-term Prediction Research and Transition (SPoRT) programs in Huntsville, AL have established a working partnership with KMD to enhance its regional modeling capabilities. SPoRT and SERVIR are providing experimental land surface initialization datasets and model verification capabilities for capacity building at KMD. To support its forecasting operations, KMD is running experimental configurations of the Weather Research and Forecasting (WRF; Skamarock et al. 2008) model on a 12-km/4-km nested regional domain over eastern Africa, incorporating the land surface datasets provided by NASA SPoRT and SERVIR. SPoRT, SERVIR, and KMD participated in two training sessions in March 2014 and June 2015 to foster the collaboration and use of unique land surface datasets and model verification capabilities. Enhanced regional modeling capabilities have the potential to improve guidance in support of daily operations and high-impact weather and climate outlooks over Eastern Africa. For enhanced land-surface initialization, the NASA Land Information System (LIS) is run over Eastern Africa at ~3-km resolution, providing real-time land surface initialization data in place of interpolated global model soil moisture and temperature data available at coarser resolutions. Additionally, real-time green vegetation fraction (GVF) composites from the Suomi-NPP VIIRS instrument is being incorporated into the KMD-WRF runs, using the product generated by NOAA/NESDIS. Model verification capabilities are also being transitioned to KMD using NCAR's Model *Corresponding author address: Jonathan Case, ENSCO, Inc., 320 Sparkman Dr., Room 3008, Huntsville, AL, 35805. Email: Jonathan.Case-1@nasa.gov Evaluation Tools (MET; Brown et al. 2009) software in conjunction with a SPoRT-developed scripting package, in order to quantify and compare errors in simulated temperature, moisture and precipitation in the experimental WRF model simulations. This extended abstract and accompanying presentation summarizes the efforts and training done to date to support this unique regional modeling initiative at KMD. To honor the memory of Dr. Peter J. Lamb and his extensive efforts in bolstering weather and climate science and capacity-building in Africa, we offer this contribution to the special Peter J. Lamb symposium. The remainder of this extended abstract is organized as follows. The collaborating international organizations involved in the project are presented in Section 2. Background information on the unique land surface input datasets is presented in Section 3. The hands-on training sessions from March 2014 and June 2015 are described in Section 4. Sample experimental WRF output and verification from the June 2015 training are given in Section 5. A summary is given in Section 6, followed by Acknowledgements and References.

land surface modeling↗
NASA NTRS1976

Remote sensing of soil moisture with microwave radiometers

Results are presented that were derived from measurements made by microwave radiometers during the March 1972 and February 1973 flights of National Aeronautics and Space Administration (NASA) Convair-9900 aircraft over agricultural test sites in the southwestern part of United States. The purpose of the missions was to study the use of microwave radiometers for the remote sensing of soil moisture. The microwave radiometers covered the 0.8- to 21-cm wavelength range. The results show a good linear correlation between the observed microwave brightness temperature and moisture content of the 0- to 1-cm layer of the soil. The results at the largest wavelength (21 cm) show the greatest sensitivity to soil moisture variations and indicate the possibility of sensing these variations through a vegetative canopy. The effect of soil texture on the emission from the soil was also studied and it was found that this effect can be compensated for by expressing soil moisture as a percent of field capacity for the soil. The results were compared with calculations based on a radiative transfer model for layered dielectrics and the agreement is very good at the longer wavelengths. At the shorter wavelengths, surface roughness effects are larger and the agreement becomes poorer.

Schmugge, T.↗
DOE OSTI2022

Liquefaction of pelleted corn cobs

Liquid slurries at high loadings (pumpable slurries) are critical to handle the streams between the unit operations in a biorefinery. Their liquefaction potential was initially tested with a small-scale method using 3FPU Ctec-2 /g dry biomass, and results were confirmed in 1L bioreactors experiments. Liquid slurries of cobs were observed in small scale tests (based on visual appearance, and reducing sugars released). Results were confirmed in 1L bioreactors under similar experimental conditions. Yield stress value in bioreactor was 34 ± 6Pa at 96 h, and glucan and xylan conversion to glucose and xylose, respectively, were 41 and 21%. In addition, work has been initiated with liquefaction of other pelleted corn stover fractions: Husk/Leaf (A),Husk (B), Stems (D) and controls (whole corn stover; F and G). Compositional analysis of the pellets showed glucan content (%) in the samples ranged from 31.9 to 36.1, xylan from 19.1 to 20.9, total lignin 13.1 to 18.8,and total ash 1.73 to 10.19. The moisture content ranged from 6.21 to 11.66%. Given these similar characteristics, we also examined liquefaction of these other samples, and they also showed that liquid slurries are possible. Work is continuing to define favourable conditions for liquid slurries formation.

Cruz, Antonio↗
NASA NTRS1975

A radiative transfer model for microwave emissions from bare agricultural soils

A radiative transfer model for microwave emissions from bare, stratified agricultural soils was developed to assist in the analysis of data gathered in the joint soil moisture experiment. The predictions of the model were compared with preliminary X band (2.8 cm) microwave and ground based observations. Measured brightness temperatures at vertical and horizontal polarizations can be used to estimate the moisture content of the top centimeter of soil with + or - 1 percent accuracy. It is also shown that the Stokes parameters can be used to distinguish between moisture and surface roughness effects.

Burke, W. J.↗
NASA NTRS1977

Theory for passive microwave remote sensing of near-surface soil moisture

The theory of microwave thermal emission from a nonscattering half-space medium is developed for application to regions with nonuniform subsurface soil-moisture and temperature variations. A coherent stratified model is presented which is valid for nonuniform temperature profiles and rapidly varying moisture profiles, under which conditions the commonly used emissivity and radiative-transfer approaches become inaccurate. For naturally occurring profiles the stratified model gives more accurate results than the other approaches at frequencies below about 4 GHz. Experimental results from ground-based radiometric observations of a controlled target area compare systematically with brightness temperatures predicted from the theoretical model to within approximately 10 K. Results of dielectric-constant measurements of the sand are given at seven frequencies in the microwave range and for moisture contents in the range from 0% to 30% by volume. By using this model, the thermal microwave emission spectrum is computed for a number of representative moisture and temperature profiles in the frequency range from 0.25 to 25 GHz.

Njoku, E. G.↗
NASA NTRS1979

Grain quality inspection system

A review of grain quality indicators and measurement methods was conducted in order to assess the feasibility of using remote sensing technology to develop a continuous monitoring system for use during grain transfer operations. Most detection methods were found to be too slow or too expensive to be incorporated into the normal inspection procedure of a grain elevator on a continuous basis. Two indicators, moisture content and broken corn and foreign material, show potential for automation and are of an economic value. A microprocessor based system which utilizes commercially available electronic moisture meter was developed and tested. A method for automating BCFM measurement is described. A complete system description is presented along with performance test results.

Flood, C. A., Jr.↗
NASA NTRS1986

Spectral reflectance relationships to leaf water stress

Spectral reflectance data were collected from detached snapbean leaves in the laboratory with a multiband radiometer. Four experiments were designed to study the spectral response resulting from changes in leaf cover, relative water content of leaves, and leaf water potential. Spectral regions included in the analysis were red (630-690 nm), NIR (760-900 nm), and mid-IR (2.08-2.35 microns). The red and mid-IR bands showed sensitivity to changes in both leaf cover and relative water content of leaves. The NIR was only highly sensitive to changes in leaf cover. Results provided evidence that mid-IR reflectance was governed primarily by leaf moisture content, although soil reflectance was an important factor when leaf cover was less than 100 percent. High correlations between leaf water potentials and reflectance were attributed to covariances with relative water content of leaves and leaf cover.

Ripple, William J.↗
NASA NTRS1991

Environmental exposure effects on composite materials for commercial aircraft

A study was conducted to determine the effects of long term flight and ground exposure on three commercially available graphite-epoxy material systems: T300/5208, T300/5209, and T300/934. Sets of specimens were exposed on commercial aircraft and ground racks for 1, 2, 3, 5, and 10 years. Inflight specimen sites included both the interior and exterior of aircraft based in Hawaii, Texas, and New Zealand. Ground racks were located at NASA-Dryden and the above mentioned states. Similar specimens were exposed to controlled lab conditions for up to 2 years. After each exposure, specimens were tested for residual strength and a dryout procedure was used to measure moisture content. Both room and high temperature residual strengths were measured and expressed as a pct. of the unexposed strength. Lab exposures included the effects of time alone, moisture, time on moist specimens, weatherometer, and simulated ground-air-ground cycling. Residual strengths of the long term specimens were compared with residual strengths of the lab specimens. Strength retention depended on the exposure condition and the material system. Results showed that composite materials can be successfully used on commercial aircraft if environmental effects are considered.

Hoffman, Daniel J.↗
NASA NTRS1974

Remote sensing of soil moisture with microwave radiometers

Microwave radiometry has been used for the remote sensing of soil moisture in a series of aircraft flights over an agricultural test area in the vicinity of Phoenix, Arizona. The radiometers covered the wavelength range 0.8-21 cm. Ground truth in the form of gravimetric measurements of the soil moisture in the top 15 cm were obtained for 200 fields at this site. The results indicate that it is possible to monitor moisture variations with airborne radiometers. The emission is a function of the radiometer wavelength and the distribution of the moisture in the soil. At a wavelength of 1.55 cm there is little or no variation in the emission for soil moisture values below 10 or 15% moisture content by weight. Above this value, there is a linear decrease in the emission with a slope of approximately 3 K for each percentage point increase in soil moisture.

Schmugge, T.↗
NASA NTRSDate not supplied

State of Wildfires

Fire is an essential component of ecosystems and acts as key driver of biogeochemical cycling with impacts on vegetation structure and composition, soil conditions, and climate feedbacks. Fire behavior and effects vary based on the types of fuel, fuel dryness, and frequency of ignition. Due to changing climate and land use patterns, fire danger is increasing in many regions globally, and fires are having increasingly devastating impacts on human health, infrastructure, and ecosystem services. Recurrent fires help to determine the distribution of trees and grasses, and overall fuel load, which inform the behavior of future fires. Process-based models can be used to capture multi-scale impacts at the forest stand-level up to the landscape level, and across minutes to centuries, but must capture variation in fire behavior and intensity as a function of the fuel and climate, from high intensity forest crown fires within boreal regions to low intensity rapid grass fires of the tropics. Fire model development demonstrates our ability to capture large scale fire influenced biogeography and vegetation distribution at the earth system scale through vegetation traits and fire feedbacks. At the individual stand scale the importance of interactions and feedbacks between above and below ground process is essential to capturing the vegetation dynamics across boreal forest systems. Improving the mechanics of including plant physiology and specifically live fuel moisture content is the next step to advancing the capability of process based models to inform fire research. Advances in the testing and creation of a mechanistic live fuel moisture model demonstrate the foundation for future live fuel dynamics research that can be informed by field and remote sensing information. Improved remote sensing, technological and modeling capabilities support a more comprehensive and cohesive fire response that will be better equipped to overcome current barriers and anticipate the new reality of fires in a warming world.

wildfires↗
DOE OSTI2025

Evaluation of desiccation cracking characteristics of inorganic micro-fiber-reinforced engineered barrier material (IMEBM) for geological repository

Abstract Buffer material is crucial for the engineering barrier system to dispose of high-level radioactive waste in a geological repository. A reliable buffer material should be able to maintain good sealing characteristics and minimize desiccation cracking. In this study, the effectiveness of inorganic fiber-reinforced engineering barrier material in reducing desiccation cracks in bentonite was evaluated via desiccation tests, image analysis, and air permeability tests. The effects of fiber type (E-glass fiber and basalt fiber) and fiber content (0.0%, 0.5%, 1.0%, 1.5%, 3.0%, and 5.0% of dry weight of the bentonite) on the development of desiccation cracks in the fiber–bentonite mixtures with the same given initial moisture content were evaluated. The results indicated that the addition of fibers could significantly reduce the crack size and area in bentonite during the drying. Basalt fibers showed a slightly better reinforcement effect than E-glass fibers when the fiber content was lower than 3.0%. The addition of fibers prevented the development of penetrating cracks and significantly reduced the permeability of the bentonite after drying. The permeabilities of basalt fiber- and E-glass fiber-reinforced bentonite composites with 3% reinforcement were 5.81 × 10 –11 m 2 and 7.24 × 10 –11 m 2 , respectively, which were 64 and 51 times smaller than that of pure bentonite. X-ray–CT observation of the internal structure of the samples after drying showed that the addition of fibers significantly changed the crack morphology and potentially increased the tortuosity.

Feng, Yuan↗