SEARCH · Search NASA

Results for “Crystal System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1971

The kinetics of crystallization of molten binary and ternary oxide systems and their application to the origination of high modulus glass fibers

Emphasis on the consideration of glass formation on a kinetic process made it possible to think of glass compositions different from those normally employed in the manufacture of glass fibers. Approximately 450 new glass compositions were prepared and three dozen of these compositions have values for Young's modulus measured on bulk specimens greater than nineteen million pounds per square inch. Of the new glasses about a hundred could be drawn into fibers by mechanical methods at high speeds. The fiber which has a Young's modulus measured on the fiber of 18.6 million pounds per square inch and has been prepared in quantity as a monofilament (to date more than 150 million lineal feet of 0.2 to 0.4 mil fiber have been produced). This fiber has also been successfully incorporated both in epoxy and polyimide matrices. The epoxy resin composite has shown a modulus forty percent better than that achievable using the most common grade of competitive glass fiber, and twenty percent better than that obtainable with the best available grade of competitive glass fiber. Other glass fibers of even higher modulus have been developed.

Bacon, J. F.↗

NASA NTRS1979

Wideband EMG telemetry system

Miniature, individual crystal-controlled RF transmitters located in EMG pressure sensors simplifies multichannel EMG telemetry for electronic gait monitoring. Transmitters which are assigned operating frequencies within 174 - 216 MHz band have linear frequency response from 20 - 2000 Hz and operate over range of 15 m.

Rosatino, S. A.↗

NASA NTRS1990

Magnetism and superconductivity of some Tl-Cu oxides

Many copper oxide based Thallium compounds have now been discovered. In comparison to the Bi-compounds, the Tl-system shows a richer diversity; viz., High Temperature Superconductors (HTSC) can be obtained with either one or two Tl-0 layers (m = 1,2); also, the triple-digit phases are easier to synthesize. The value of d, oxygen stoichiometry, is critical to achieving superconductivity. The Tl system is robust to oxygen loss; Tl may be lost or incorporated by diffusion. A diffusion coefficient equal to 10 ms at 900 C was determined. Both ortho-rhombic and tetragonal structures are evidenced, but HTSC behavior is indifferent to the crystal symmetry. This system has the highest T(sub c) confirmed. T(sub c) generally increases with p, the number of CuO layers, but tends to saturate at p = 3. Zero resistance as high as 125K has been observed. Most of these HTSC's are hole type, but the Ce-doped specimens may be electronic. The magnetic aspects were studied; because in addition to defining the perfectly diamagnetic ground state as in the conventional superconductors, magnetism of the copper oxides show a surprising variety. This is true of both the normal and the superconducting states. Also, due to the large phonon contribution to the specific heat at the high T(sub c) accurate thermal measurement of important parameters such as the sp. heat jump, electronic density of states, D(Ef) and coherence length are uncertain, and thus, are estimated from the magnetic results. Results from the Tl-system CuO, LaBaCuO, 120 and the Bi-CuO compounds are discussed. The emphasis is on the role of magnetism in the TlCuO HTSC, but technological aspects are also pointed out.

Datta, Timir↗

NASA NTRS1991

Magnetism and superconductivity of some Tl-Cu oxides

Many copper oxide based Thallium compounds are now known. In comparison to the Bi-compounds, the Tl-system shows a richer diversity; i.e., High Temperature Superconductors (HTSC) can be obtained with either one or two Tl-0 layers (m = 1,2); also, the triple-digit phases are easier to synthesize. The value of d, oxygen stoichiometry, is critical to achieving superconductivity. The Tl system is robust to oxygen loss; Tl may be lost or incorporated by diffusion. A diffusion coefficient equal to 10 ms at 900 C was determined. Both ortho-rhombic and tetragonal structures are found, but HTSC behavior is indifferent to the crystal symmetry. This system has the highest T(sub c) confirmed. T(sub c) generally increases with p, the number of CuO layers, but tends to saturate at p = 3. Zero resistance was observed at temperatures as great as 125 K. Most of these HTSC's are hole type, but the Ce-doped specimens may be electronic. The magnetic aspects were studied; because in addition to defining the perfectly diamagnetic ground state as in conventional superconductors, magnetism of the copper oxides show a surprising variety. This is true of both the normal and the superconducting states. Also, due to the large phonon contribution to the specific heat at the high T(sub c) jump, electronic density of states, D(Ef), and coherence length are uncertain, and thus, are estimated from the magnetic results. Results from the Tl-system CuO, LaBaCuO,120 and the Bi-CuO compounds are discussed. The emphasis is on the role of magnetism in the Tl-CuO HTSC, but technological aspects are also pointed out.

Datta, Timir↗

NASA NTRS2014

Detection of the Impact of Ice Crystal Accretion in an Aircraft Engine Compression System During Dynamic Operation

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation community. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. Here a detection algorithm is developed which has the capability to detect the impact of ice accretion in the Low Pressure Compressor of an aircraft engine during steady flight as well as during changes in altitude. Unfortunately, the algorithm as implemented was not able to distinguish throttle changes from ice accretion and thus more work remains to be done.

high ice water content↗

NASA NTRS2014

Detection of the Impact of Ice Crystal Accretion in an Aircraft Engine Compression System During Dynamic Operation

detection↗

NASA NTRS1987

Soft x ray window encapsulant for HgI2 detectors

HgI2 is an excellent semiconductor material for a low energy, room temperature x-ray spectrometer. The high values of the atomic numbers for its constituent elements gives high x-ray and gamma ray stopping power. The band gap of HgI2 is significantly higher than other commonly used semiconductors. Owing to the large value band gap, the leakage current for HgI2 devices is smaller, thus allowing low noise performance. Devices fabricated from HgI2 crystals have demonstrated energy resolution sufficient to distinguish the x-ray emission from the neighboring elements on the periodic table. Also the power requirements of HgI2 are very low. These characteristics make a HgI2 spectrometer an ideal component in a satellite based detection system. Unfortunately, HgI2 crystals tend to deteriorate with time, even if protected by standard semiconductor encapsulants. This degradation ruins the performance of the device in terms of its energy resolution and pulse amplitude. The degrading mechanism is believed to be material loss occurring from below the electrodes, due to high vapor pressure of HgI2 at room temperature. To address this major obstacle to rapid expansion of HgI2 technology, a research program aimed at improving device stability by encapsulation with inert polymeric materials was carried out. The program focused specifically on optimizing the encapsulant materials and their deposition techniques. The principal objectives for this program were device encapsulation, device testing, and accelerated testing to ensure very long term stability of these high resolution sensors. A variety of encapsulants were investigated with the selection criteria based on their chemical diffusion barrier properties, mechanical stability, reactivity, and morphology of encapsulant films. The investigation covered different classes of encapsulants including solvent based encapsulants, vapor deposited encapsulants, and plasma polymerized encapsulants. A variety of characterization techniques were employed to examine their effectiveness in stabilizing HgI2 devices; these included permeability evaluation, vacuum and heat testing, scanning electron microscopy (SEM) as well as studying the detector performance of coated detectors. The plasma polymerized films appear to have entirely solved the HgI2 degradation problem. Another achievement of this program was the development of an accelerated testing technique which correlates extremely well with long term tesing.

Entine, G.↗

NASA NTRS1995

Stress Tuning of Laser Crystals

The topic of stress tunable laser crystals is addressed in this study with the purpose of determining the piezo-optic coefficients of a new laser material. This data was collected using a quadruple pass birefringence technique because of its high degree of sensitivity relative to the other methods examined including fringe shift analysis using a Mach-Zender interferometer. A green He-Ne laser was passed through a light chopper and Glan-Thompson prism before entering a crystal of Erbium doped Yttrium Aluminum Garnet (Er:YAG) (used in order to validate the experimental technique). The Er:YAG crystal is mounted in a press mechanism and the laser is quadruple passed through test specimen before being returned through the prism and the orthogonally polarized portion of the beam measured with a optical sensor. At a later stage, the Er:YAG crystal was replaced with a new crystal in order to determine the piezo-optic coefficients of this uncharacterized material. The applied load was monitored with the use of a 50 lb. load cell placed in line with the press. Light transmission readings were taken using a lock-in amplifier while load cell measurements were taken with a voltmeter from a 5 volt, 0.5 amp power supply. Despite the fact that an effective crystal press damping system was developed, size limitations precluded the use of the complete system. For this reason, data points were taken only once per full turn so as to minimize the effect of non uniform load application on the collected data. Good correlation was found in the transmission data between the experimentally determined Er:YAG and the previously known peizo-optic constants of non-doped crystal with which it was compared. The variation which was found between the two could be accounted for by the aforementioned presence of Erbium in the experimental sample (for which exact empirical data was not known). The same test procedure was then carried out on a Yttrium Gallium Aluminum garnet (YGAG) for the purpose of establishing values of its unknown piezo-optic constant tensor using experimentally collected transmission data. Significant variation between the piezo-optic constants of YAG and YGAG crystals was found however, the excellent data correlation of separate experimental runs carried out on the YGAG sample demonstrates the validity of these results. The data collected during the stressing of the YGAG was of high quality, however the amount of data collected was somewhat limited by a fracture of YGAG specimen which undoubted altered the crystalline lattice structure and hence precluded any further testing.

Carty, Atherton A.↗

DOE OSTI2024

Understanding the effect of crystal anisotropy on grain growth, texturing and transport via the orthorhombic ?-U system [Slides]

The alpha phase of uranium exhibits the orthorhombic crystal structure, resulting in significant physical property anisotropy. These complex properties make the material challenging to work with in engineering settings but provide a rich arena to investigate the fundamental, multi-scale effects of anisotropy on physical behaviors such as grain growth and microstructure evolution under irradiation. We apply molecular dynamics and phase field modeling to study mass transport and grain growth in alpha-uranium. We characterize the mobilities of crystalline defects and the interfacial energy, and We find that the grain boundary energy is highly variable depending on the interface structure and that the relative rates of defect transport change with temperature. We also find that anisotropic thermal expansion has a significant impact on grain growth kinetics and texture development. Our results are used to explain experimental observations and to provide a basis for further hypotheses into the complex physical behavior of alpha-uranium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS2013

Advanced Optical Diagnostics for Ice Crystal Cloud Measurements in the NASA Glenn Propulsion Systems Laboratory

A light extinction tomography technique has been developed to monitor ice water clouds upstream of a direct connected engine in the Propulsion Systems Laboratory (PSL) at NASA Glenn Research Center (GRC). The system consists of 60 laser diodes with sheet generating optics and 120 detectors mounted around a 36-inch diameter ring. The sources are pulsed sequentially while the detectors acquire line-of-sight extinction data for each laser pulse. Using computed tomography algorithms, the extinction data are analyzed to produce a plot of the relative water content in the measurement plane. To target the low-spatial-frequency nature of ice water clouds, unique tomography algorithms were developed using filtered back-projection methods and direct inversion methods that use Gaussian basis functions. With the availability of a priori knowledge of the mean droplet size and the total water content at some point in the measurement plane, the tomography system can provide near real-time in-situ quantitative full-field total water content data at a measurement plane approximately 5 feet upstream of the engine inlet. Results from ice crystal clouds in the PSL are presented. In addition to the optical tomography technique, laser sheet imaging has also been applied in the PSL to provide planar ice cloud uniformity and relative water content data during facility calibration before the tomography system was available and also as validation data for the tomography system. A comparison between the laser sheet system and light extinction tomography resulting data are also presented. Very good agreement of imaged intensity and water content is demonstrated for both techniques. Also, comparative studies between the two techniques show excellent agreement in calculation of bulk total water content averaged over the center of the pipe.

Bencic, Timothy J.↗

NASA NTRS1974

Assessment of the technology required to develop photovoltaic power system for large scale national energy applications

A technical assessment of a program to develop photovoltaic power system technology for large-scale national energy applications was made by analyzing and judging the alternative candidate photovoltaic systems and development tasks. A program plan was constructed based on achieving the 10 year objective of a program to establish the practicability of large-scale terrestrial power installations using photovoltaic conversion arrays costing less than $0.50/peak W. Guidelines for the tasks of a 5 year program were derived from a set of 5 year objectives deduced from the 10 year objective. This report indicates the need for an early emphasis on the development of the single-crystal Si photovoltaic system for commercial utilization; a production goal of 5 x 10 to the 8th power peak W/year of $0.50 cells was projected for the year 1985. The developments of other photovoltaic conversion systems were assigned to longer range development roles. The status of the technology developments and the applicability of solar arrays in particular power installations, ranging from houses to central power plants, was scheduled to be verified in a series of demonstration projects. The budget recommended for the first 5 year phase of the program is $268.5M.

Lutwack, R.↗

NASA NTRS1999

Growth of Solid Solution Single Crystals

The objective of the study is to establish the effects of processing semiconducting, solid solution, single crystals in a microgravity environment on the metallurgical, compositional, electrical, and optical characteristics of the crystals. The alloy system being investigated is the solid solution semiconductor Hg(1-x)Cd(x)Te, with x-values appropriate for infrared detector applications in the 8 to 14 mm wavelength region. Both melt and Te-solvent growth are being performed. The study consists of an extensive ground-based experimental and theoretical research effort followed by flight experimentation where appropriate. The ground-based portion of the investigation also includes the evaluation of the relative effectiveness of stabilizing techniques, such as applied magnetic fields, for suppressing convective flow during the melt growth of the crystals.

Lehoczky, Sandor L.↗

NASA NTRS1981

Recent progress in the NASA-Goddard Space Flight Center atomic hydrogen standards program

At NASA Goddard Space Flight Center and through associated contractors, a broad spectrum of work is being carried out to develop improved hydrogen maser frequency standards for field use, improved experimental hydrogen maser frequency standards, and improved frequency and time distribution and measurement systems for hydrogen maser use. Recent progress in the following areas is reported: results on the Nr masers built by the Applied Physics Laboratory of Johns Hopkins University, the development of a low cost hydrogen maser at Goddard Space Flight Center, and work on a low noise phase comparison system and digitally phase locked crystal oscillator called the distribution and measurement system.

Reinhardt, V. S.↗

NASA NTRS1985

Processing of Complex Compound Semiconductors in Space

The purpose of this first year ground based research effort was to develop growth and characterization facilities for bulk single crystals of compound semiconductor alloys. As a system of 2-6 alloy crystal growth, C sub x Mn sub (1-x)Te was chosen since it has a relatively narrow solidus-liquidus separation serving as a suitable first model for zone melting and solution growth. Also, it allows, in principle, perfect lattice matching to Cd sub x Hg sub(1-x)Te that needs to be studied as a model for the investigation of heteroepitaxial growth from Te-solutions. A vertical zone melting furnace was built and used in the synthesis of Cd sub x Mn sub(1-x)Te from the elements and crystal growth in carbon coated fused silica crucibles of Bridgman growth geometry. Photoluminescence spectra of the crystals reveal band to band recombination at energies that agree with the reported literature data. In addition, deep luminescence is present at energies corresponding to proportional shifts from the 1.4 eV deep emission observed for bulk single crystals of CdTe.

Bachmann, K.↗

NASA NTRS2017

Design of Multifunctional Materials: Chalcogenides and Chalcopyrites

There is a strong need for developing multifunctional materials to reduce the cost of applied material without compromising the performance of the detectors, devices and sensors. The materials design, processing, growth and fabrication of bulk and nanocrystals and fabrication into devices and sensors involve huge cost and resources including a multidisciplinary team of experts. Because of this reason, prediction of multifunctionality of materials before design and development should be evaluated. Chalcogenides and chalcopyrites are a very exciting class of materials for developing multifunctionality. Materials such as Gallium selenide GaSe and zinc selenide ZnSe have been proven to be excellent examples. GaSe is a layered material and very difficult to grow in large crystal. However, it's ternary and quaternary analogs such as thallium gallium selenide TlGaSe2, thallium gallium selenide sulfide TlGaSe2-xSs, thallium arsenic selenide Tl3AsSe3, silver gallium selenide AgGaGe3Se8, AgGaGe5Se12 and several others have shown great promise for multifunctionality. Several of these materials have shown good efficiency for frequency conversion (nonlinear optical NLO), electro-optic modulation, and acousto-optic tunable filters and imagers suitable for the visible, near-infrared wavelength, mid wave infrared (MWIR), long wave infrared (LWIR) and even up to Tera hertz wavelength (THW) regions. In addition, this class of materials have demonstrated low absorption coefficients and power handling capability in the systems. Also, these crystals do not require post growth annealing, show very large transparency range and fabricability.

Singh, N. B.↗

DOE OSTI2025

Thermodynamic phase transitions of nematic order in magnetic helices

A nematic phase lacks translation order but has orientational order. Nematic phases have been discovered in a variety of systems, including liquid crystals, correlated materials, and superconductors. Here, we report on a magnetic nematic phase, where the basis components are composed of magnetic helices. We directly probed the order parameters associated with the magnetic helices using resonant soft x-ray scattering and find two distinct nematic phases with complex spatiotemporal signatures. Using x-ray correlation spectroscopy, we find that near the phase boundary between the two nematic phases, fluctuations coexist on multiple disparate timescales. Our micromagnetic simulations and density functional theory calculations show that the fluctuations occur concomitantly with a reorientation of the magnetic helices, indicating spontaneous symmetry breaking and the emergence of additional degrees of freedom. Our results provide a framework for characterizing exotic phases that can be extended to a broad class of physical systems.

36 MATERIALS SCIENCE↗

NASA NTRS1985

Solutal Convection and Its Effects on Crystal Growth and Segregation in Binary and Pseudo-Binary System with Large Liquidus-Solidus Separation

This research program is composed of theoretical and experimental studies of solutal convection and its effects on crystal growth and segregation in binary and pseudo-binary systems with large liquidus-solidus separation. The theoretical program has resulted in the development of a transient simulation of the growth of concentrated alloys in microgravity and has been used to study the dynamics of GeSi, PbSnTe, HgCdTe growth. Finite element analysis has also been developed for studying the interactions of buoyancy-driven convection in the melt caused by temperature and concentration variations with melt-solid interface morphology and alloy segregation in the grown crystal. These calculations are being compared directly to experimental measurements of segregation and interface shape for GeSi growth and GaGe growth. The results for SiGe indicate that careful design of the thermal system can result in almost diffusion-controlled growth on Earth because of the stablizing influence of the concentration gradient ahead of the solidification front.

Brown, R. A.↗

NASA NTRS2017

Shergottite Lead Isotope Signature in Chassigny and the Nakhlites

The nakhlites/chassignites and the shergottites represent two differing suites of basaltic martian meteorites. The shergottites have ages less than or equal to 0.6 Ga and a large range of initial Sr-/Sr-86 and epsilon (Nd-143) ratios. Conversely, the nakhlites and chassignites cluster at 1.3-1.4 Ga and have a limited range of initial Sr-87/Sr-86 and epsilon (Nd-143). More importantly, the shergottites have epsilon (W-182) less than 1, whereas the nakhlites and chassignites have epsilon (W-182) approximately 3. This latter observation precludes the extraction of both meteorite groups from a single source region. However, recent Pb isotopic analyses indicate that there may have been interaction between shergottite and nakhlite/chassignite Pb reservoirs.Pb Analyses of Chassigny: Two different studies haveinvestigated 207Pb/204Pb vs. 206Pb/204Pb in Chassigny: (i)TIMS bulk-rock analyses of successive leaches and theirresidue [3]; and (ii) SIMS analysis of individual minerals[4]. The bulk-rock analyses fall along a regression of SIMSplagioclase analyses that define an errorchron that is olderthan the Solar System (4.61±0.1 Ga); i.e., these define amixing line between Chassigny’s principal Pb isotopic components(Fig. 1). Augites and olivines in Chassingy (notshown) also fall along or near the plagioclase regression [4].This agreement indicates that the whole-rock leachateslikely measure indigenous, martian Pb, not terrestrial contamination[5]. SIMS analyses of K-spars and sulfides definea separate, sub-parallel trend having higher 207Pb/206Pbvalues ([4]; Fig. 1). The good agreement between the bulkrockanalyses and the SIMS analyses of plagioclases alsoindicates that the Pb in the K-spars and sulfides cannot be amajor component of Chassigny.The depleted reservoir sampled by Chassigny plagioclaseis not the same as the solar system initial (PAT) andrequires a multi-stage origin. Here we show a two-stagemodel (Fig. 1) with a 238U/204Pb (μ) of 0.5 for 4.5-2.4 Gaand a μ of 7 for 2.4-1.4 Ga. This is not a unique model butdoes produce a Pb composition that falls on the plagioclaseregression at 1.4 Ga, the approximate igneous age of Chassigny [1]. It should be noted that low-μ single-stage modelsare not capable of producing sufficiently radiogenic 206Pb/204Pb at 1.4 Ga.Relation to Shergottites: The Chassigny K-spars and sulfides fall along a second mixing line defined by leachesand residues of depleted and intermediate shergottites [6]. This mixing line falls above the plagioclase regression.Therefore, we also interpret the radiogenic component of this mixing line to represent indigenous martian Pb. It ispossible that the depleted and intermediate shergottites and the Chassigny plagioclases sample radiogenic Pb from thethe same source, i.e., the mixing lines may intersect at high 206Pb/204Pb.Both K-spar and sulfide are late-stage phases. At the time of their crystallization, the Chassigny system appearsto have remained open to a depleted shergottite Pb reservoir. The depleted component of the shergottite mixing linecan be generated by a single-stage evolution from PAT (4.5 to 1.4 Ga) in a reservoir having a μ ~2. A similar modelfor the most depleted shergottites is also possible: μ = 1.5 for 4.5 to 0.3 Ga.Nakhlites: Nakhlite analyses plot between the shergottite and Chassigny plagioclase regressions [3]. So again,members of the nakhlite/chassignite suite show affinities to shergottite Pb.

Jones, J. H.↗