Search NASA⌕ Search

SEARCH · Search NASA

Results for “SUPERALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

The effects of Cr, Al, Ti, Mo, W, Ta, and Cb on the cyclic oxidation behavior of cast Ni-base superalloys at 1100 and 1150 C

Fifty Ni-base superalloys with concentrations of Cr, Al, Ti, Mo, W, Ta, and Cb systematically varied between two nonzero levels, were tested for cyclic oxidation resistance at 1100 and 1150 C. Oxidation resistance was interpreted in terms of the rate of specific weight change and the types of oxides formed. It is found that the resistance of the alloys to cyclic oxidation is largely determined by Al content, with a sharp increase in the oxidation resistance observed in the Al concentration range 5-8 at. pct. The effects of the other elements studied were small compared with that of aluminum. Best oxidation resistance characteristics were predicted for high Al (13 at. pct), low Cr (10 at. pct), low Ti (2 at. pct), low Cb (1 at. pct), and high Mo, W, and Ta (3 at. pct each). The effects of the refractory metals, however, are somewhat ambiguous and should be investigated further. Higher boron contents, which were unintentionally varied, were clearly detrimental even for the most resistant compositions.

Barrett, C. A.↗
NASA NTRS1984

Creep-rupture behavior of six candidate Stirling engine superalloys tested in air

The creep-rupture behavior of six candidate Stirling engine iron-base superalloys was determined in air. The alloys included four wrought alloys (A-286, Alloy 800H, N-155, and 19-9DL) and two cast alloys (CRM-6D and XF-818). The specimens were tested to rupture for times up to 3000 h at 650 to 925 C. Rupture life, t(r) minimum creep rate, and time to 1-percent creep strain t(0.01) were statistically analyzed as a function of stress and temperature. Estimated stress levels at different temperatures to obtain 3500 h t(r) and t(0.01) lives were determined. These data will be compared with similar data being obtained under 15 MPa hydrogen.

Bhattacharyya, S.↗
NASA NTRS1984

Response of Inconel 617 superalloy to combined ground-based and STS reentry exposure

Inconel 617 is a nickel-based superalloy which is being considered for heat-shield applications because of its high-temperature strength, good oxidation resistance and high emittance of oxidized surfaces. While the effects of simulated reentry conditions on emittance and oxidation of Inconel 617 have been studied, the combined effects of the ground-based environment with sea salt exposure and the reentry environment have not been evaluated. Experimental results are presented to show the effects of environmental simulation including ground-based and reentry exposure on the emittance and oxidation of Inconel 617. Specimens were exposed to simulated reentry at a surface temperature of 2000 F in the Langley Research Center Hypersonic Materials Environmental Test System (HYMETS) Facility with and without alternate exposures to an atmospheric seashore environment or a laboratory sea salt environment. This paper presents emittance, mass loss, oxide chemistry, and alloy composition data for the specimens.

Clark, R. K.↗
NASA NTRS1984

Morphological changes of gamma prime precipitates in nickel-base superalloy single crystals

Changes in the morphology of the gamma prime precipitate were examined during tensile creep at temperatures between 927 and 1038 C in 001-oriented single crystals of a Ni-Al-Mo-Ta superalloy. In this alloy, which has a large negative misfit of -0.80%, the gamma prime particles link together during creep to form platelets, or rafts, which are aligned with their broad faces perpendicular to the applied tensile axis. The dimensions of the gamma and gamma prime phases were measured as directional coarsening developed in an attempt to trace the changing morphology under various stress levels. In addition, the effects of initial microstructure, as well as slight compositional variations, were related to raft development and creep properties. The results showed that directional coarsening of gamma prime began during primary creep, and under certain conditions, continued to develop after the onset of steady-state creep. The length of the rafts increased linearly with time up to a plateau region. The thickness of the rafts, however, remained equal to the initial gamma prime size at least up through the onset of tertiary creep; this is a clear indication of the stability of the finely-spaced gamma-gamma prime lamellar structure. It was found that the single crystals with the finest gamma prime size exhibited the longest creep lives, because the resultant rafted structure had a larger number of gamma-gamma prime interfaces per unit volume of material.

Mackay, R. A.↗
NASA NTRS1984

The Effects of Seven Alloying Elements on the Microstructure and Stress-Rupture Behavior of Nickel-Base Superalloys

Seven alloying elements: Al, Cr, Ti, Nb, Ta, Mo, and W were added at two levels of concentration to produce a series of experimental nickel-base superalloys. Fifty alloys, representing a fraction of a 2 to the 7th power factorial design, were cast, tested, and analyzed. Each alloy's microstructure was characterized by phase extractions, X-ray diffraction, metallography and energy dispersive X-ray spectroscopy. Regression analysis was used to determine the effect of alloying element content on microstructure and stress-rupture life.

Hull, D. R.↗
NASA NTRS1984

Studies on the hot corrosion of a nickel-base superalloy, Udimet 700

The hot corrosion of a nickel-base superalloy, Udimet 700, was studied in the temperature range of 884 to 965 C and with different amounts of Na2SO4. Two different modes of degradation were identified: (1) formation of Na2MoO4 - MoO3 melt and fluxing by this melt, and (2) formation of large interconnected sulfides. The dissolution of Cr2O3, TiO2 in the Na2SO4 melt does not play a significant role in the overall corrosion process. The conditions for the formation of massive interconnected sulfides were identified and a mechanism of degradation due to sulfide formation is described. The formation of Ns2MoO4 - MoO3 melt requires an induction period and various physiochemical processes during the induction period were identified. The factors affecting the length of the induction period were also examined. The melt penetration through the oxide appears to be the prime mode of degradation whether the degradation is due to the formation of sulfides or the formation of the Na2MoO4 - MoO3 melt.

Misra, A. K.↗
NASA NTRS1984

High temperature low-cycle fatigue mechanisms in single crystals of nickel-based superalloy Mar-M 200

Twenty three high temperature low-cycle fatigue tests were conducted on single crystals of the nickel-based superalloy Mar-M 200. Tests were conducted at 760 and 870 C. SEM fractography and transmission electron microscopy were used to determine mechanisms responsible for the observed orientation dependent fatigue behavior. It has been concluded that the plastic characteristics of the alloy lead to orientation-dependent strain hardening and fatigue lives at 760 C. At 870 C, the elastic characteristics of the alloy dominated the behavior, even though the plastic strain ranges were about the same as they were at 760 C. This led to orientation-dependent fatigue lives, but the trends were not the same as they were at 760 C.

Milligan, W. W.↗
NASA NTRS1984

The effects of Cr, Co, Al, Mo and Ta on the cyclic oxidation behavior of a prototype cast Ni-base superalloy based on a 2(5) composite statistically designed experiment

A series of cast Ni-base superalloys were systematically varied at selected levels of Co, Cr, Mo, Ta, and Al. The elemental levels varied were Mo, 0 to 4 percent; Cr, 6 to 18 percent; Co, 0 to 20 percent, Ta, 0 to 8 percent; and Al, 3.25 to 6.25 percent. The cyclic oxidation resistance was determined from specific weight change data as a function of time for 1 hr cycles in static air at 1100 C. The significant terms in decreasing order of their importance were Al, Ta, Cr2, Al-Cr, Cr-Co, Co2, Al-Mo, Cr-Mo, Al-Al, and Mo-Ta. The Al term alone accounted for close to 82 percent of the explained variability. The estimating equation showed that the Al level was the most important and should be at its 6.25 wt % maximum value. The Mo and Ta levels should also be at their maximum 4 and 8 wt % respectively. The cobalt composition should be as low as possible, i.e., 0 wt%. The Cr level optimum varies depending on the other 4 levels. The X-ray diffaction results indicate the most protective scales are alumina/aluminate spinel stabilizized with a tri-rutile oxide high in Ta and Mo.

Barrett, C. A.↗
NASA NTRS1984

Creep-rupture behavior of iron superalloys in high-pressure hydrogen

The creep-rupture properties of five iron-base and one cobalt-base high temperature alloys were investigated to assess the feasibility of using the alloys as construction materials in a Stirling engine. The alloys were heat treated and hardness measurements were taken. Typical microstructures of the alloys are shown. The creep-rupture properties of the alloys were determined at 760 and 815 C in 15.0 MPa H2 for 200 to 1000 hours. Plots of rupture life versus stress for the six superalloys are presented along with creep strain-time plots.

Bhattacharyya, S.↗
NASA NTRS1985

Nonlinear structural analysis for fiber-reinforced superalloy turbine blades

A computational capability for predicting the nonlinear thermomechanical structural response of fiber-reinforced superalloy (FRS) turbine blades is described. This capability is embedded in a special purpose computer code (COBSTRAN) developed at the NASA Lewis Research Center. Special features of this computational capability include accounting for: fiber/matrix reaction, nonlinear and anisotropic material behavior, complex stress distribution due to local and global heterogeneity, and residual stresses due to initial fabrication and/or inelastic behavior during subsequent missions. Numerical results are presented from analyses of a hypothetical FRS turbine blade subjected to a fabrication process and subsequent mission cycle. The results demonstrate the capabilities of this computational tool to; predict local stress/strain response and capture trends of local nonlinear and anisotropic material behavior, relate the effects of this local behavior to the global response of a multilayered fiber-composite turbine blade, and trace material history from fabrication through successive missions.

Hopkins, D. A.↗
NASA NTRS1985

Properties and microstructures for dual alloy combinations of three superalloys with alloy 901

Dual alloy combinations have potential for use in aircraft engine components such as turbine disks where a wide range of stress and temperature regimes exists during operation. Such alloy combinations may directly result in the conservation of elements which are costly or not available domestically. Preferably, a uniform heat treatment yielding good properties for both alloys should be used. Dual alloy combinations of iron rich Alloy 901 with nickel base superalloys Rene 95, Astroloy, or MERL 76 were not isostatically pressed from prealloyed powders. Individual alloys, alloy mixtures, and layered alloy combinations were given the heat treatments specified for their use in turbine disks or appropriate for Alloy 901. Selected specimens were overaged for 1500 hr at 650 C. Metallographic examinations revealed the absence of phases not originally present in either alloy of a combination. Mechanical tests showed adequate properties in combinations of Rene 95 or Astroloy with Alloy 901 when given the Alloy 901 heat treatment. Combinations with MERL 76 had better properties when given the MERL 76 heat treatment. The results indicate that these combinations are promising candidates for use in turbine disks.

Harf, F. H.↗
NASA NTRS1985

Constitutive Modeling of Superalloy Single Crystals and Directionally Solidified Materials

A unified viscoplastic constitutive relation based on crystallographic slip theory was developed for the deformation analysis of nickel base face centered cubic superalloy single crystals at elevated temperature. The single crystal theory is embedded in a self consistent method to derive a constitutive relation for a directionally solidified material comprised of a polycrystalline aggregate of columnar cylindrical grains. One of the crystallographic axes of the cylindrical crystals points in the columnar direction while the remaining crystallographic axes are oriented at random in the basal plane perpendicular to the columnar direction. These constitutive formulations are coded in FORTRAN for use in nonlinear finite element and boundary element programs.

Walker, K. P.↗
NASA NTRS1985

Vapor deposited emittance/catalysis coatings for superalloys in heatshield applications

Statically oxidized Inconel 617 and MA 956 superalloys were prepared with vapor deposited aluminosilicate layers and exposed to temperatures which simulated reentry conditions. The aluminosilicate layers were 1-2 microns thick. The trials consisted of exposures to 1500-2300 F heat while surface temperatures were monitored with pyrometers. Analyses were then performed of the catalytic activity, oxidation phenomena, and radiative properties after thermal cycling the specimens for 8 hr. Both alloys were found to be catalytic to the recombination processes of dissociated species in the reentry environment. The coatings reduced the catalytic activity by 40 percent for both alloys but did not change the emittance. An enhanced Cr depletion zone was detected in the Inconel samples, implying that the coating did not prevent diffusion loss of Cr. The coated MA 956, on the other hand, gained weight over the course of the trials.

Clark, R. K.↗
NASA NTRS1985

Elevated temperature creep-rupture behavior of the single crystal nickel-base superalloy NASAIR 100

The creep and rupture behavior of 001-line-oriented single crystals of the nickel-base superalloy NASAIR 100 was investigated at temperatures of 925 and 1000 C. In the stress and temperature ranges studied, the steady state creep rate, time to failure, time to the onset of secondary creep, and the time to the onset of tertiary creep all exhibited power law dependencies on the applied stress. The creep rate exponents for this alloy were between seven and eight, and the modulus-corrected activation energy for creep was approximately 350 kjoule/mole, which was comparable to the measured activation energy for Ostwald ripening of the gamma-prime precipitates. Oriented gamma-prime coarsening to form lamellae perpendicular to the applied stress was very prominent during creep. At 1000 C, the formation of a continuous gamma-gamma-prime lamellar structure was completed during the primary creep stage. Shear through the gamma-gamma-prime interface is considerd to be the rate limiting step in the deformation process. Gradual thickening of the lamellae appeared to be the cause of the onset of tertiary creep. At 925 C, the fully developed lamellar structure was not achieved until the secondary or tertiary creep stages. At this temperature, the gamma-gamma-prime lamellar structure did not appear to be as beneficial for creep resistance as at the higher temperature.

Nathal, M. V.↗
NASA NTRS1984

Factors which influence directional coarsening of gamma-prime during creep in nickel-base superalloy single crystals

Changes in the morphology of the gamma prime precipitate were examined as a function of the time during creep at 982 C in 001 oriented single crystals of a Ni-Al-Mo-Ta superalloy. In this alloy, which has a large negative misfit of -0.80 pct., the gamma prime particles link together during creep to form platelets, or rafts, which are aligned with their broad faces perpendicular to the applied tensile axis. The effects of initial microstructure and alloy composition of raft development and creep properties were investigated. Directional coarsening of gamma prime begins during primary creep and continues well after the onset of second state creep. The thickness of the rafts remains constant up through the onset of tertiary creep, a clear indication of the stability of the finely-spaced gamma/gamma prime lamellar structure. The thickness of the rafts which formed was equal to the initial gamma prime size which was present prior to testing. The single crystals with the finest gamma prime size exhibited the longest creep lives, because the resultant rafted structure had a larger number of gamma/gamma prime interfaces per unit volume of material. Reducing the Mo content by only 0.73 wt. pct. increased the creep life by a factor of three, because the precipitation of a third phase was eliminated.

Mackay, R. A.↗
NASA NTRS1984

Effects of cobalt on the hot workability of nickel-base superalloys

The effect of cobalt on the workability of nickel-base superalloys is examined with reference to experimental results for four heats of alloys based on the Nimonic 115 composition with varying amounts of nickel substituted for the nominal 14 percent cobalt. It is shown that Co lowers the gamma-prime solvus, which in turn lowers the Cr23C6 carbide solvus. It is further shown that these solvus temperatures bracket the hot working range for the alloys. However, thermomechanical processing modifications reflecting the effect of Co on the gamma-prime and carbide solvi are shown to restore the workability and the properties of alloys with little or no cobalt.

Jarrett, R. N.↗
NASA NTRS1984

Rapid solidification and dynamic compaction of Ni-base superalloy powders

A Ni-base superalloy containing 13Al-9Mo-2Ta (in at. percent) has been characterized in both the rapidly solidified condition and after dynamic compaction. Dynamically compacted specimens were examined in the as-compacted condition and observations related to current theories of interparticle bonding. In addition, the recrystallization behavior of the compacted material at relatively low temperature (about 0.5-0.75 Tm) was investigated.

Field, R. D.↗
NASA NTRS1985

PM superalloys - A troubled adolescent?

The history of powder metallurgy P/M superalloy technology is reviewed with a comment on the state of the art, and speculates on the technology's future potential growth and maturity.

Dreshfield, R. L.↗