SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Lifting body stability augmentation systems design, development, ground tests and flight data including frequency response, limit cycle and structural resonance
A program was undertaken to characterize Ryton-B resin, develop graphite filament prepregs, undirectional laminates and determine the strength and heat resistance of the composite system. Through the use of a water soluble resin binder, high quality prepreg tape, three inches wide with 4 tows of HM-S were produced. The tape laminated to 0.00175 inch per ply. A wide range of properties in the cured resin and laminate were found using different curing conditions. The thermal stability and strength of molded laminates appears to be very dependent upon the cure cycle used for polymerization.
An analysis has been developed which relates the effects of inelastic behavior of Y2O3 stabilized ZrO2 (YSZ) materials. The results show these materials to be sensitive to small changes in temperature and are supported by measurements of inelastic behavior in disk and bar specimens at temperatures as low as 1010 C (1850 F). At higher thermomechanical loads, the test specimens can deform to strains greater than 1 percent and for bar specimens, with sufficient strength, to remain bonded to the metallic substrate.
A temperature-compensated resistance static strain gage with potential to be used to 600 C was recently developed. Gages were fabricated from specially developed palladium-13 w/o chromium (Pd-13Cr) wire and platinum (Pt) compensator. When bonded to high temperature Hastelloy X, the apparent strain from room temperature to 600 C was within 400 microstrain for gages with no preheat treatment and within 3500 microstrain for gages with 16 hours prestabilization at 640 C. The apparent strain versus temperature relationship of stabilized PdCr gages were repeatable with the reproducibility within 100 microstrain during three thermal cycles to 600 C and an 11 hours soak at 600 C. The gage fabrication, construction and installation is described. Also, the coating system used for this compensated resistance strain gage is explained. The electrical properties of the strain sensing element and main characteristics of the compensated gage including apparent strain, drift and reproducibility are discussed.
The results are presented of a variety of spherically symmetric one-dimensional (1D) calculations intended to determine the robustness of the dynamical hiccup phenomenon in protostellar cores. The 1D models show that the phenomenon is relatively insensitive to changes in the equations of state, numerical resolution, initial density and temperature, and the radiative transfer approximation. In 1D, the hiccup results in an explosive destruction of the entire inner protostellar core. Inner core formation is studied with a sequence of three-dimensional models which show that rapid inner core rotation stabilizes the hiccup instability. Instead, the inner core becomes quite flat and undergoes a cycle of binary fragmentation, binary decay into a single object surrounded by a bar, breakup of the bar into a binary, etc. When lesser amounts of rotation are involved, the inner core does hiccup somewhat, but mass is ejected in only a few directions, leading to several broad streams of ejecta.
Determining structural design inputs and the structural margins following design completion is one of the major activities in space exploration. The end result is a statement of these margins as stability, safety factors on ultimate and yield stresses, fracture limits (fracture control), fatigue lifetime, reuse criteria, operational criteria and procedures, stability factors, deflections, clearance, handling criteria, etc. The process is normally called a load cycle and is time consuming, very complex, and involves much more than structures. The key to successful structural design is the proper implementation of the process. It depends on many factors: leadership and management of the process, adequate analysis and testing tools, data basing, communications, people skills, and training. This process and the various factors involved are discussed.
The objective of the task reported herein was to define, evaluate, and optimize variable geometry concepts suitable for use with a Rich-Quench-Lean (RQL) combustor. The specific intent was to identify approaches that would satisfy High Speed Civil Transport (HSCT) cycle operational requirements with regard to fuel-air ratio turndown capability, ignition, and stability margin without compromising the stringent emissions, performance, and reliability goals that this combustor would have to achieve. Four potential configurations were identified and three of these were refined and tested in a high-pressure modular RQL combustor rig. The tools used in the evolution of these concepts included models built with rapid fabrication techniques that were tested for airflow characteristics to confirm sizing and airflow management capability, spray patternation, and atomization characterization tests of these models and studies that were supported by Computational Fluid Dynamics analyses. Combustion tests were performed with each of the concepts at supersonic cruise conditions and at other critical conditions in the flight envelope, including the transition points of the variable geometry system, to identify performance, emissions, and operability impacts. Based upon the cold flow characterization, emissions results, acoustic behavior observed during the tests and consideration of mechanical, reliability, and implementation issues, the tri-swirler configuration was selected as the best variable geometry concept for incorporation in the RQL combustor evolution efforts for the HSCT.
This paper considers transonic flutter mechanisms of the Benchmark Supercritical Wing, a model under study in the Aeroelastic Prediction Workshop series. Flutter boundaries are mapped out across an angle of attack sweep at Mach 0.8, utilizing both time-domain and linearized frequency-domain solvers, manual meshes and adapted meshes, and various governing equations. With increased angle of attack, linearized and finite amplitude flutter predictions exhibit differences above 3◦ as the flow begins to separate; the latter predictions are found to be driven by subcritical limit cycle oscillations whose strength increases with angle of attack. Moderate perturbation values provide a stability boundary at 5◦ which matches the experimental data, but it is not clear how the experimental perturbation, from one test condition to the next, can be reasonably characterized.
The time-dependent behavior of a wing boundary layer immersed in a propeller slipstream has been studied experimentally in wind-tunnel tests and in flight. Hot-wire anemometer measurements were made through the boundary layer for time-dependent, ensemble-average velocity and turbulence-intensity profiles at various chord locations. The boundary layer has a coherent, time-dependent cycle of transitional behavior, varying from a laminar to a turbulent-transitional state. Local drag coefficients determined from the velocity profiles for the freewheeling propeller case in flight show that the time-dependent drag in the propeller slipstream varies from the undisturbed laminar value to a value less than that predicted for fully turbulent flow. Local drag coefficients determined from the thrusting propeller case in the wind tunnel indicate that the effects of the slipstream are to enhance the stability of the boundary layer and to reduce the drag coefficient in the laminar portion of the cycle below its undisturbed laminar value.
The moist convection parameterization used in the GISS 3-D GCM is adapted for use in a two-dimensional (2-D) zonally averaged statistical-dynamical model. Experiments with different versions of the parameterization show that its impact on the general circulation in the 2-D model does not parallel its impact in the 3-D model unless the effect of zonal variations is parameterized in the moist convection calculations. A parameterization of the variations in moist static energy is introduced in which the temperature variations are calculated from baroclinic stability theory, and the relative humidity is assumed to be constant. Inclusion of the zonal variations of moist static energy in the 2-D moist convection parameterization allows just a fraction of a latitude circle to be unstable and enhances the amount of deep convection. This leads to a 2-D simulation of the general circulation very similar to that in the 3-D model. The experiments show that the general circulation is sensitive to the parameterized amount of deep convection in the subsident branch of the Hadley cell. The more there is, the weaker are the Hadley cell circulations and the westerly jets. The experiments also confirm the effects of momentum mixing associated with moist convection found by earlier investigators and, in addition, show that the momentum mixing weakens the Ferrel cell. An experiment in which the moist convection was removed while the hydrological cycle was retained and the eddy forcing was held fixed shows that moist convection by itself stabilizes the tropics, reduces the Hadley circulation, and reduces the maximum speeds in the westerly jets.
Chemical breakdown of rocks, weathering, is an important but very slow part of the carbon cycle that ultimately leads to CO2 being locked up in carbonates on the ocean floor. Artificial acceleration of this carbon sink via distribution of pulverized silicate rocks across terrestrial landscapes may help offset anthropogenic CO2 emissions. We show that idealized enhanced weathering scenarios over less than a third of tropical land could cause significant drawdown of atmospheric CO2 and ameliorate ocean acidification by 2100. Global carbon cycle modelling driven by ensemble Representative Concentration Pathway (RCP) projections of twenty-first-century climate change (RCP8.5, business-as-usual; RCP4.5, medium-level mitigation) indicates that enhanced weathering could lower atmospheric CO2 by 30-300 ppm by 2100, depending mainly on silicate rock application rate (1 kg or 5 kg m(exp -2) yr (exp -1)) and composition. At the higher application rate, end-of-century ocean acidification is reversed under RCP4.5 and reduced by about two-thirds under RCP8.5. Additionally, surface ocean aragonite saturation state, a key control on coral calcification rates, is maintained above 3.5 throughout the low latitudes, thereby helping maintain the viability of tropical coral reef ecosystems. However, we highlight major issues of cost, social acceptability, and potential unanticipated consequences that will limit utilization and emphasize the need for urgent efforts to phase down fossil fuel emissions.
Biomass burning has been a regular practice for land clearing and land conversion in many countries, especially those in Africa, South America, and Southeast Asia. However, the unique climatology of Southeast Asia is very different than that of Africa and South America, such that large-scale biomass burning causes smoke to interact extensively with clouds during the peak-burning season of March to April. Significant global sources of greenhouse gases (e.g., CO2, CH4), chemically active gases (e.g., NO, CO, HC, CH3Br), and atmospheric aerosols are produced by biomass burning processes. These gases influence the Earth-atmosphere system, impacting both global climate and tropospheric chemistry. Some aerosols can serve as cloud condensation nuclei, which play an important role in determining cloud lifetime and precipitation, hence, altering the earth's radiation and water budget. Biomass burning also affects the biogeochemical cycling of nitrogen and carbon compounds from the soil to the atmosphere; the hydrological cycle (i.e., run off and evaporation); land surface reflectivity and emissivity; as well as ecosystem biodiversity and stability. Analyses from satellite measurements reveal that smoke is frequently present solar (emitted thermal) radiation from clouds due to smoke aerosols can be reduced (enhanced) by as much as 100 (20) W/sq m over the month of March 2000. In addition, the reduction in cloud spectral reflectance at 670 run is large enough to lead to significant errors in retrieving cloud properties (e.g., optical thickness and effective radius) from satellite measurements. The fresh water distribution in this region is highly dependent on monsoon rainfall; in fact, the predictability of the tropical climate system is much reduced during the boreal spring. Estimating the burning fuel (e.g., bark, branches, and wood), an important part of studying regional carbon cycle, may rely on utilizing a wide range of distinctive spectral features in the shortwave and longwave regions. Therefore, to accurately assess the impact of smoke aerosols in this region requires continuous observations from satellites, aircraft, networks of ground-based instruments and dedicated field experiments. A new initiative will be proposed and discussed.
Design concepts and plans for mass-production facilities and equipment, field installation, and maintenance were developed and used for cost analysis of a pneumatically stabilized plastic film point focus solar concentrator which has potential application in conjunction with Brayton cycle engines or supply of thermal energy. A sub-scale reflector was fabricated and optically tested by laser ray tracing to determine focal deviations of the surface slope and best focal plane. These test data were then used for comparisons with theoretical concentrator performance modeling and predictions of full-scale design performance. Results of the economic study indicate the concentrator design will have low cost when mass-produced and has cost/performance parameters that fall within current Jet Propulsion Laboratory goals.
THUNDER (THin UNimorph DrivER) actuators are pre-stressed piezoelectric devices developed at NASA Langley Research Center (LaRC) that exhibit enhanced strain capabilities. As a result, they are of interest in a variety of aerospace applications. Characterization of their performance as a function of electric field, temperature and frequency is needed in order to optimize their operation. Towards that end, a number of THUNDER devices were obtained from FACE International Co. with a stainless steel substrate varying in thickness from 1 mil to 20 mils. The various devices were evaluated to determine low-field and high-field displacement its well as the polarization hysteresis loops. The thermal stability of these drivers was evaluated by two different methods. First, the samples were thermally cycled under electric field by systematically increasing the maximum temperature from 25 C to 200 C while the displacement was being measured. Second, the samples were isothermally aged at 0 C, 50 C, 100 C. and 150 C in air, and the isothermal decay of the displacement was measured at room temperature as a function of time.
Russia and the U.S. provide the current International Space Station (ISS) food system. Each country contributes half of the food supply in their respective flight food packaging. All of the packaged flight food is stowed in Russian provided containers, which interface with the Service Module galley. Each country accepts the other's flight worthiness inspections and qualifications. Some of the food for the first ISS crew was launched to ISS inside the Service Module in July of 2000, and STS-106 in September 2000 delivered more food to the ISS. All subsequent food deliveries will be made by Progress, the Russian re-supply vehicle. The U.S. will ship their portion of food to Moscow for loading onto the Progress. Delivery schedules vary, but the goal is to maintain at least a 45-day supply onboard ISS at all times. The shelf life for ISS food must be at least one year, in order to accommodate the long delivery cycle and onboard storage. Preservation techniques utilized in the US food system include dehydration, thermo stabilization, intermediate moisture, and irradiation. Additional fresh fruits and vegetables will be sent with each Progress and Shuttle flights as permitted by volume allotments. There is limited refrigeration available on the Service Module to store fresh fruits and vegetables. Astronauts and cosmonauts eat half U.S. and half Russian food. Menu planning begins 1 year before a planned launch. The flight crews taste food in the U.S. and in Russia and rate the acceptability. A preliminary menu is planned, based on these ratings and the nutritional requirements. The preliminary menu is then evaluated by the crews while training in Russia. Inputs from this evaluation are used to finalize the menu and flight packaging is initiated. Flight food is delivered 6 weeks before launch. The current challenge for the food system is meeting the nutritional requirements, especially no more than 10 mg iron, and 3500 mg sodium. Experience from Shuttle[Mir also indicated insufficient caloric intake for many crewmembers. Additional thermostabilized and irradiated foods have been developed for ISS to improve the ease of preparation and overall acceptability. Dehydrated foods offer limited advantage, since water must be delivered to ISS. An effort is underway to introduce other International Partner's food into the ISS food system. At first this will be one or two selected foods with the potential for more as the program matures. An increase in the variety of available foods would improve the overall acceptability. Additional galley capability will be required when the crew size increases on ISS. Anticipated improvements include freezers, refrigerators and microwave ovens. All of the ISS food development efforts are devoted to improving the food acceptability and subsequent consumption and mission success
A system analysis and preliminary design were conducted for an organic Rankine-cycle system to bottom the high-temperature waste heat of an adiabatic diesel engine. The bottoming cycle is a compact package that includes a cylindrical air cooled condenser regenerator module and other unique features. The bottoming cycle output is 56 horsepower at design point conditions when compounding the reference 317 horsepower turbocharged diesel engine with a resulting brake specific fuel consumption of 0.268 lb/hp-hr for the compound engine. The bottoming cycle when applied to a turbocompound diesel delivers a compound engine brake specific fuel consumption of 0.258 lb/hp-hr. This system for heavy duty transport applications uses the organic working fluid RC-1, which is a mixture of 60 mole percent pentafluorobenzene and 40 mole percent hexafluorobenzene. The thermal stability of the RC-1 organic fluid was tested in a dynamic fluid test loop that simulates the operation of Rankine-cycle. More than 1600 hours of operation were completed with results showing that the RC-1 is thermally stable up to 900 F.
The GEOstationary Coastal and Air Pollution Events (GEO-CAPE) Airborne Simulator (GCAS) was developed at NASA’s Goddard Space Flight Center (GSFC) and has flown in multiple field campaigns to perform mapping of the regional-scale EPA criteria pollutants nitrogen dioxide, ozone, and formaldehyde. GCAS will also participate invalidation campaigns for NASA’s Tropospheric Emissions: Monitoring POllution (TEMPO) mission and the Korean Geostationary Environment Monitoring Spectrometer (GEMS) mission, both scheduled to launch in the early 2020s. GCAS houses two commercial Offner-type grating spectrometers that measure backscattered solar spectral radiance from the near-ultraviolet to near-infrared at high spatial resolution (typically 250 meters at 8.5 kilometer altitude). These radiances are used to retrieve spatial and temporal distributions of trace gases relevant to the boundary layer and free tropospheric atmospheric chemistry cycles. In this paper, we describe the field calibration techniques employed to characterize the spectral and temporal radiometric stability of the system during its most recent deployment in the 2018 Long Island Sound Trace Ozone Study (LISTOS) field campaign. Overall measurement uncertainty, retrieval impacts, and lessons learned for future deployments will also be described.
Many blunt-body entry vehicles have nonlinear dynamic stability characteristics that produce self-limiting oscillations in flight. Several different test techniques can be used to extract dynamic aerodynamic coefficients to predict this oscillatory behavior for planetary entry mission design and analysis. Most of these test techniques impose boundary conditions that alter the oscillatory behavior from that seen in flight. Three sets of test conditions, representing three commonly used test techniques, are presented to highlight these effects. Analytical solutions to the constant-coefficient planar equations-of-motion for each case are developed to show how the same blunt body behaves differently depending on the imposed test conditions. The energy equation is applied to further illustrate the governing dynamics. Then, the mean value theorem is applied to the energy rate equation to find the effective damping for an example blunt body with nonlinear, self-limiting dynamic characteristics. This approach is used to predict constant-energy oscillatory behavior and the equilibrium oscillation amplitudes for the various test conditions. These predictions are verified with planar simulations. The analysis presented provides an overview of dynamic stability test techniques and illustrates the effects of dynamic stability, static aerodynamics and test conditions on observed dynamic motions. It is proposed that these effects may be leveraged to develop new test techniques and refine test matrices in future tests to better define the nonlinear functional forms of blunt body dynamic stability curves.