Search NASA⌕ Search

SEARCH · Search NASA

Results for “routing problems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Exploring Management of Arrival Spacing Using Route Extensions with Terminal Spacing Tools

Airports with shared runway operations between arrivals and departures can experience severe departure gridlock and delays during a heavy arrival push due to insufficient gaps in the arrival stream for aircraft to depart. The problem is accentuated in situations when a large gap in the arrival spacing has to be created at the last minute due to wake vortex separation requirements. At LaGuardia airport, wake vortex separation problems arise when a heavy jet, such as a B757, departing on Runway 31 needs additional spacing between arrivals on Runway 22. A standard solution for controllers in many airports in situations such as this is to extend the downwind leg of arrival aircraft to create extra space between the arrivals. The question addressed in this paper is how such route extensions would work with terminal scheduling operations, namely (1) the automated Terminal Sequencing and Spacing (TSS) tools and (2) a new scheduling tool which increases the availability of gaps for departure aircraft (Departure Sensitive Arrival Spacing or DSAS). In a simulated LaGuardia airport (LGA) Terminal Radar Approach Control (TRACON) airspace, two new RNAV arrival routes were created along with extensions to these routes. The arrival route from the south had a downwind leg extension near the airport in the final sector. The arrival route from the north had an extension in a feeder sector further from the airport. An exploratory one-hour run with the route extensions was compared to an hour run without the extensions. Topics included in the paper are 1) how the route extensions were developed, 2) a procedure outlining how the aircraft could be scheduled to the extensions and who would do it, and 3) the results of the exploratory run compared to the original run without the extensions. The results indicated that the extended downwind leg route helped to create a B757 departure gap in the middle of a packed arrival stream, resulting in a reduction of 11 minutes in average wait time for the B757s, but at a cost of increased controller self-reported workload from low to moderate.

time based flow management↗

Dynamic Routing of Aircraft in the Presence of Adverse Weather Using a POMDP Framework

Each year weather-related airline delays result in hundreds of millions of dollars in additional fuel burn, maintenance, and lost revenue, not to mention passenger inconvenience. The current approaches for aircraft route planning in the presence of adverse weather still mainly rely on deterministic methods. In contrast, this work aims to deal with the problem using a Partially Observable Markov Decision Processes (POMDPs) framework, which allows for reasoning over uncertainty (including uncertainty in weather evolution over time) and results in solutions that are more robust to disruptions. The POMDP-based decision support system is demonstrated on several scenarios involving convective weather cells and is benchmarked against a deterministic planning system with functionality similar to those currently in use or under development.

Decision making↗

Prediction of an alternative high-pressure route to polymeric carbon dioxide as a metastable energetic material

The use of pressure to obtain new materials that can be recovered under ambient conditions is a central problem in high-pressure physics. Despite decades of research, this goal has only been achieved in the laboratory for a few notable examples, such as diamond and cubic boron nitride. An area of significant interest is the transformation under compression of light-element molecular compounds to extended covalent-bonded (polymeric) solids. Among them, CO 2 has been extensively studied because of its status as a prototypical simple molecular system with a rich phase diagram and due to its fundamental role in Earth’s physics and chemistry. One of its polymeric crystalline phases, accessible at extreme pressures and temperatures, has been recently quenched to ambient pressure, but below room temperature. Here we report ab initio calculations predicting that isothermal compression of a carbon monoxide and oxygen mixture (CO+O 2 ), rather than the compound CO 2 , lowers the onset of C-polymerization at room temperature from ~ 118 GPa to ~ 7 GPa (complete by ~ 23 GPa). Moreover, it leads to the formation of an intrinsically different polymer with enhanced metastability. We predict that this dense phase is an energetic material which can potentially be recovered to ambient pressure and temperature.

Paul, Reetam [Lawrence Livermore National Laborato↗

Future of Fuel Savings

Using automation to free up controllers for more strategic management of air traffic is one approach being studied by NASA as it seeks to boost airspace system capacity and efficiency, thereby saving fuel. Heinz Erzberger, a NASA Ames Research Center senior scientist, says the Advanced Airspace Concept (AAC) has been studied for several years. It could increase efficiency 15% by providing optimal routes that cut airlines direct operating costs. A 25% increase in landings on existing runways could follow an important benefit. AAC is one of the efforts to be reviewed by the Joint Planning and Development Organization, an FAA-led initiative by six federal agencies to redesign the U.S. air transportation system by 2025. The main goal is to triple air traffic capacity within 20 years to avert the sort of gridlock that would make fuel consumption only one of many travel nightmares. The automated system approach would allow aircraft to fly optimal trajectories. A trajectory would be defined in the standard three dimensions and eventually include the fourth, time. The management of air traffic by the data-linked exchange of trajectories would start at high altitude and eventually move down to lower altitudes. The automated concept is an outgrowth of the type of tools developed by NASA for use by FAA controllers in managing traffic flows over the years, including ones that optimize routings for the best fuel burn. But AAC would push automation further to reduce workload so controllers can focus on "solving strategic control problems, managing traffic flow during changing weather and ... other unusal events." One key component, the automated trajectory server (ATS), is a ground systems that would rely on software to manage flight path requests from aircrews and controllers. But, Erzberger acknowledges, "The FAA's current plan for upgrades to air traffic services does not include [allowing] the future ground system to issue separation-critical clearances of trajectory changes autonomously to aircraft via data link without explicit approval of a controller," as the AAC proposes. The AAC enables pilots or controllers to data link requests for a trajectory change to the ATS for approval after they are deconflicted with the paths of other aircraft. To divert around storms, for example, pilots could data link their trajectory preference to the ATS. Since several aircraft might request similar routes, the computer would then have to suggest alternatives. This could be accomplished without pilot-controller radio calls, a big bottleneck now. The ATS would have a built-in conflict monitor to call for a resolution (turn, climb or descend), when loss of separation is likely in 1-20 min. The AAC system would reduce controller errors by 90%, according to NASA Ames estimates. The AAC would have a back-up program to assure separation-Tactical Separation Assurance (TSAFE). It s designed to detect short-term traffic conflicts within 3-4 min. of loss of separation. The last line of defense would still be provided by traffic alert & collision avoidance systems (TCAS).

Hughes, David↗

Extremely durable biofouling-resistant metallic surfaces based on electrodeposited nanoporous tungstite films on steel

Formation of unwanted deposits on steels during their interaction with liquids is an inherent problem that often leads to corrosion, biofouling and results in reduction in durability and function. Here we report a new route to form anti-fouling steel surfaces by electrodeposition of nanoporous tungsten oxide (TO) films. TO-modified steels are as mechanically durable as bare steel and highly tolerant to compressive and tensile stresses due to chemical bonding to the substrate and island-like morphology. When inherently superhydrophilic TO coatings are converted to superhydrophobic, they remain non-wetting even after impingement with yttria-stabilized-zirconia particles, or exposure to ultraviolet light and extreme temperatures. Upon lubrication, these surfaces display omniphobicity against highly contaminating media retaining hitherto unseen mechanical durability. Furthermore, to illustrate the applicability of such a durable coating in biofouling conditions, we modified naval construction steels and surgical instruments and demonstrated significantly reduced marine algal film adhesion, Escherichia coli attachment and blood staining.

36 MATERIALS SCIENCE↗

Experimental demonstration of a quantum annealing algorithm for the traveling salesman problem in a nuclear-magnetic-resonance quantum simulator

The method of quantum annealing (QA) is a promising way for solving many optimization problems in both classical and quantum information theory. The main advantage of this approach, compared with the gate model, is the robustness of the operations against errors originated from both external controls and the environment. In this work, we succeed in demonstrating experimentally an application of the method of QA to a simplified version of the traveling salesman problem by simulating the corresponding Schroedinger evolution with a NMR quantum simulator. The experimental results unambiguously yielded the optimal traveling route, in good agreement with the theoretical prediction.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electricity Transmission, Pipelines, and National Trails: An Analysis of Current and Potential Intersections on Federal Lands in the Eastern United States, Alaska, and Hawaii

As has been noted in many reports and publications, acquiring new or expanded rights-of-way for transmission is a challenging process, because numerous land use and land ownership constraints must be overcome to develop pathways suitable for energy transmission infrastructure. In the eastern U.S., more than twenty federally protected national trails (some of which are thousands of miles long, and cross many states) pose a potential obstacle to the development of new or expanded electricity transmission capacity. However, the scope of this potential problem is not well-documented, and there is no baseline information available that could allow all stakeholders to study routing scenarios that could mitigate impacts on national trails. This report, Electricity Transmission, Pipelines, and National Trails: An Analysis of Current and Potential Intersections on Federal Lands in the Eastern United States, was prepared by the Environmental Science Division of Argonne National Laboratory (Argonne). Argonne was tasked by DOE to analyze the “footprint” of the current network of National Historic and Scenic Trails and the electricity transmission system in the 37 eastern contiguous states, Alaska, and Hawaii; assess the extent to which national trails are affected by electrical transmission; and investigate the extent to which national trails and other sensitive land use types may be affected in the near future by planned transmission lines. Pipelines are secondary to transmission lines for analysis, but are also within the analysis scope in connection with the overall directives of Section 368 of the Energy Policy Act of 2005, and because of the potential for electrical transmission lines being collocated with pipelines. Based on Platts electrical transmission line data, a total of 101 existing intersections with national trails on federal land were found, and 20 proposed intersections. Transmission lines and pipelines are proposed in Alaska; however there are no locations that intersect national trails. Source data did not indicate any planned transmission lines or pipelines in Hawaii. A map atlas provides more detailed mapping of the topics investigated in this study, and the accompanying GIS database provides the baseline information for further investigating locations of interest. In many cases the locations of proposed transmission lines are not accurately mapped (or a specific route may not yet be determined), and accordingly the specific crossing locations are speculative. However since both national trails and electrical transmission lines are long linear systems, the characteristics of the crossings reported in this study are expected to be similar to both observed characteristics of the existing infrastructure provided in this report, and of the new infrastructure if these proposed projects are built. More focused study of these siting challenges is expected to mitigate some of potential impacts by choosing routes that minimize or eliminate them. The current study primarily addresses a set of screening-level characterizations that provide insights into how the National Trail System may influence the siting of energy transport facilities in the states identified under Section 368(b) of the Energy Policy Act of 2005. As such, it initializes gathering and beginning analysis of the primary environmental and energy data, and maps the contextual relationships between an important national environmental asset and how this asset intersects with energy planning activities. Thus the current study sets the stage for more in-depth analyses and data development activities that begin to solve key transmission siting constraints. Our recommendations for future work incorporate two major areas: (1) database development and analytics and (2) modeling and scenario analysis for energy planning. These recommendations provide a path forward to address key issues originally developed under the Energy Policy Act of 2005 that are now being carried forward under the President’s Climate Action Plan.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Electricity Transmission, Pipelines, and National Trails: An Analysis of Current and Potential Intersections on Federal Lands in the Eastern United States, Alaska, and Hawaii

As has been noted in many reports and publications, acquiring new or expanded rights-of-way for transmission is a challenging process, because numerous land use and land ownership constraints must be overcome to develop pathways suitable for energy transmission infrastructure. In the eastern U.S., more than twenty federally protected national trails (some of which are thousands of miles long, and cross many states) pose a potential obstacle to the development of new or expanded electricity transmission capacity. However, the scope of this potential problem is not well-documented, and there is no baseline information available that could allow all stakeholders to study routing scenarios that could mitigate impacts on national trails. This report, Electricity Transmission, Pipelines, and National Trails: An Analysis of Current and Potential Intersections on Federal Lands in the Eastern United States, was prepared by the Environmental Science Division of Argonne National Laboratory (Argonne). Argonne was tasked by DOE to analyze the “footprint” of the current network of National Historic and Scenic Trails and the electricity transmission system in the 37 eastern contiguous states, Alaska, and Hawaii; assess the extent to which national trails are affected by electrical transmission; and investigate the extent to which national trails and other sensitive land use types may be affected in the near future by planned transmission lines. Pipelines are secondary to transmission lines for analysis, but are also within the analysis scope in connection with the overall directives of Section 368 of the Energy Policy Act of 2005, and because of the potential for electrical transmission lines being collocated with pipelines.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Data acquisition and path selection decision making for an autonomous roving vehicle

The feasibility of using range/pointing angle data such as might be obtained by a laser rangefinder for the purpose of terrain evaluation in the 10-40 meter range on which to base the guidance of an autonomous rover was investigated. The decision procedure of the rapid estimation scheme for the detection of discrete obstacles has been modified to reinforce the detection ability. With the introduction of the logarithmic scanning scheme and obstacle identification scheme, previously developed algorithms are combined to demonstrate the overall performance of the intergrated route designation system using laser rangefinder. In an attempt to cover a greater range, 30 m to 100 mm, the problem estimating gradients in the presence of positioning angle noise at middle range is investigated.

Shen, C. N.↗

Mechanical design problems associated with turbopump fluid film bearings

Most high speed cryogenic turbopumps for liquid propulsion rocket engines currently use ball or roller contact bearings for rotor support. The operating speeds, loads, clearances, and environments of these pumps combine to make bearing wear a limiting factor on turbopump life. An example is the high pressure oxygen turbopump (HPOTP) used in the Space Shuttle Main Engine (SSME). Although the HPOTP design life is 27,000 seconds at 30,000 rpms, or approximately 50 missions, bearings must currently be replaced after 2 missions. One solution to the bearing wear problem in the HPOTP, as well as in future turbopump designs, is the utilization of fluid film bearings in lieu of continuous contact bearings. Hydrostatic, hydrodynamic, and damping seal bearings are all replacement candidates for contact bearings in rocket engine high speed turbomachinery. These three types of fluid film bearings have different operating characteristics, but they share a common set of mechanical design opportunities and difficulties. Results of research to define some of the mechanical design issues are given. Problems considered include transient strat/stop rub, non-operational rotor support, bearing wear inspection and measurement, and bearing fluid supply route. Emphasis is given to the HPOTP preburner pump (PBP) bearing, but the results are pertinent to high-speed cryogenic turbomachinery in general.

Evces, Charles R.↗

A synopsis of the weather problems facing today's general aviation pilots

Concentration on weather to data has primarily been at the point of observation. There have been efforts to obtain and disseminate en route weather through pilot reports (PIREPS), but the efforts have been meager. What is needed is the cooperative efforts on the application of technology to the acquisition and dissemination of the en route weather data for those pilots in the air as well as those who are flight planning on the ground. A comprehensive three-dimensional computer storage system is proposed that receives weather information from all aircraft on IFR flight plans and stores this information by altitude and geographic coordinates. Also, a report on the Federal Aviation Administration's Research Engineering and Development Aviation Weather Program from the aspect of past, present and future is given.

Pope, J. C.↗

Phase retrieval of diffraction from highly strained crystals

An important application of phase retrieval methods is to invert coherent x-ray diffraction measurements to obtain real-space images of nanoscale crystals. The phase information is currently recovered from reciprocal-space amplitude measurements by the application of iterative projective algorithms that solve the nonlinear and nonconvex optimization problem. Various algorithms have been developed each of which apply constraints in real and reciprocal space on the reconstructed object. In general, these methods rely on experimental data that is oversampled above the Nyquist frequency. To date, support-based methods have worked well, but are less successful for highly strained structures, defined as those which contain (real-space) phase information outside the range of {+-}{pi}/2. As a direct result the acquired experimental data is, in general, inadvertently subsampled below the Nyquist frequency. In recent years, a new theory of 'compressive sensing' has emerged, which dictates that an appropriately subsampled (or compressed) signal can be recovered exactly through iterative reconstruction and various routes to minimizing the l{sub 1} norm or total variation in that signal. This has proven effective in solving several classes of convex optimization problems. Here we report on a 'density-modification' phase reconstruction algorithm that applies the principles of compressive sensing to solve the nonconvex phase retrieval problem for highly strained crystalline materials. The application of a nonlinear operator in real-space minimizes the l{sub 1} norm of the amplitude by a promotion-penalization (or 'propenal') operation that confines the density bandwidth. This was found to significantly aid in the reconstruction of highly strained nanocrystals. We show how this method is able to successfully reconstruct phase information that otherwise could not be recovered.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Prime factorization using magnonic holographic devices

Determining the prime factors of a given number $N$ is a problem that requires super-polynomial time for conventional digital computers. A polynomial-time algorithm was invented by Shor for quantum computers. In this paper, we present experimental data that demonstrate prime factorization using spin-wave interference but without quantum entanglement. Prime factorization includes three major steps. First, a general-type computer calculates the sequence of numbers m k mod($N$), where $N$ is the number to be factorized, m is a randomly chosen positive integer, and k = 1, 2, 3, 4, 5, 6…. Next, the period of the calculated sequence $r$ is determined by exploiting spin-wave interference. Finally, the general-type computer determines the primes based on the obtained $r$. The experiment for period finding was conducted on a six-terminal Y 3 Fe 2 (FeO 4 ) 3 device. We chose number 15 for testing and determined its primes using a sequence of measurements. The obtained experimental data for a micrometer-sized prototype aimed to demonstrate the benefits of using spin-wave devices to solve complex computational problems. Scalability is one of the major strengths inherent in this type of wave-based device, which may provide a route to nanometer-sized logic circuits. We discuss the physical and technological limitations of this approach, which define the maximum size of N and the computational speed. Although this classical approach cannot compete with the quantum algorithm in terms of efficiency, magnonic holographic devices can potentially be used as complementary logic units aimed at speeding up prime factorization for classical computers.

97 MATHEMATICS AND COMPUTING↗

Interference Moral Hazard in Large Multihop Networks

Cooperation between network nodes is critical for supporting services in ad hoc networks. Cooperation, however, is an idealized assumption that may not always be present. This assumption can fail because of moral hazard, a scenario in part caused by misaligned incentives between the requesting node and supporting node. In this paper, we characterize a moral hazard that perversely incentivizes nodes to increase their routing payments by transmitting interference into the multi-hop network. We refer to this as the interference moral hazard (IMH) problem which is inherent to strategyproof mechanisms with low overpayments. We investigate IMH as a non-cooperative game played by network nodes on a random graph. For large networks, we show that IMH can be solved in the network design space. Finally, we provide sufficient conditions on the network distribution that guarantee an equilibrium path with interference-free play. This is achieved by 1) lower-bounding the number of nodes and 2) bounding the network density slightly above the 2-connectedness threshold and below a proposed upper-bound. Simulations suggest that density plays a fundamental role in IMH.

42 ENGINEERING↗

An optimization model for the US Air-Traffic System

A systematic approach for monitoring U.S. air traffic was developed in the context of system-wide planning and control. Towards this end, a network optimization model with nonlinear objectives was chosen as the central element in the planning/control system. The network representation was selected because: (1) it provides a comprehensive structure for depicting essential aspects of the air traffic system, (2) it can be solved efficiently for large scale problems, and (3) the design can be easily communicated to non-technical users through computer graphics. Briefly, the network planning models consider the flow of traffic through a graph as the basic structure. Nodes depict locations and time periods for either individual planes or for aggregated groups of airplanes. Arcs define variables as actual airplanes flying through space or as delays across time periods. As such, a special case of the network can be used to model the so called flow control problem. Due to the large number of interacting variables and the difficulty in subdividing the problem into relatively independent subproblems, an integrated model was designed which will depict the entire high level (above 29000 feet) jet route system for the 48 contiguous states in the U.S. As a first step in demonstrating the concept's feasibility a nonlinear risk/cost model was developed for the Indianapolis Airspace. The nonlinear network program --NLPNETG-- was employed in solving the resulting test cases. This optimization program uses the Truncated-Newton method (quadratic approximation) for determining the search direction at each iteration in the nonlinear algorithm. It was shown that aircraft could be re-routed in an optimal fashion whenever traffic congestion increased beyond an acceptable level, as measured by the nonlinear risk function.

Mulvey, J. M.↗

Real-time processing of radar return on a parallel computer

NASA is working with the FAA to demonstrate the feasibility of pulse Doppler radar as a candidate airborne sensor to detect low altitude windshears. The need to provide the pilot with timely information about possible hazards has motivated a demand for real-time processing of a radar return. Investigated here is parallel processing as a means of accommodating the high data rates required. A PC based parallel computer, called the transputer, is used to investigate issues in real time concurrent processing of radar signals. A transputer network is made up of an array of single instruction stream processors that can be networked in a variety of ways. They are easily reconfigured and software development is largely independent of the particular network topology. The performance of the transputer is evaluated in light of the computational requirements. A number of algorithms have been implemented on the transputers in OCCAM, a language specially designed for parallel processing. These include signal processing algorithms such as the Fast Fourier Transform (FFT), pulse-pair, and autoregressive modelling, as well as routing software to support concurrency. The most computationally intensive task is estimating the spectrum. Two approaches have been taken on this problem, the first and most conventional of which is to use the FFT. By using table look-ups for the basis function and other optimizing techniques, an algorithm has been developed that is sufficient for real time. The other approach is to model the signal as an autoregressive process and estimate the spectrum based on the model coefficients. This technique is attractive because it does not suffer from the spectral leakage problem inherent in the FFT. Benchmark tests indicate that autoregressive modeling is feasible in real time.

Aalfs, David D.↗

Commercial opportunities in bioseparations and physiological testing aboard Space Station Freedom

The Center for Cell Research (CCR) is a NASA Center for the Commercial Development of Space which has as its main goal encouraging industry-driven biomedical/biotechnology space projects. Space Station Freedom (SSF) will provide long duration, crew-tended microgravity environments which will enhance the opportunities for commercial biomedical/biotechnology projects in bioseparations and physiological testing. The CCR bioseparations program, known as USCEPS (for United States Commercial Electrophoresis Program in Space), is developing access for American industry to continuous-flow electrophoresis aboard SSF. In space, considerable scale-up of continuous free-flow electrophoresis is possible for cells, sub cellular particles, proteins, growth factors, and other biological products. The lack of sedemination and buoyancy-driven convection flow enhances purity of separations and the amount of material processed/time. Through the CCR's physiological testing program, commercial organizations will have access aboard SSF to physiological systems experiments (PSE's); the Penn State Biomodule; and telemicroscopy. Physiological systems experiments involve the use of live animals for pharmaceutical product testing and discovery research. The Penn State Biomodule is a computer-controlled mini lab useful for projects involving live cells or tissues and macro molecular assembly studies, including protein crystallization. Telemicroscopy will enable staff on Earth to manipulate and monitor microscopic specimens on SSF for product development and discovery research or for medical diagnosis of astronaut health problems. Space-based product processing, testing, development, and discovery research using USCEPS and CCR's physiological testing program offer new routes to improved health on Earth. Direct crew involvement-in biomedical/biotechnology projects aboard SSF will enable better experimental outcomes. The current data base shows that there is reason for considerable optimism regarding what the CCDS program and the biomedical/biotechnology industry can expect to gain from a permanent manned presence in space.

Hymer, W. C.↗

NASA Solar Array Demonstrates Commercial Potential

A state-of-the-art solar-panel array demonstration site at NASA's Dryden Flight Research Center provides a unique opportunity for studying the latest in high-efficiency solar photovoltaic cells. This five-kilowatt solar-array site (see Figure 1) is a technology-transfer and commercialization success for NASA. Among the solar cells at this site are cells of a type that was developed in Dryden Flight Research Center s Environmental Research Aircraft and Sensor Technology (ERAST) program for use in NASA s Helios solar-powered airplane. This cell type, now denoted as A-300, has since been transferred to SunPower Corporation of Sunnyvale, California, enabling mass production of the cells for the commercial market. High efficiency separates these advanced cells from typical previously commercially available solar cells: Whereas typical previously commercially available cells are 12 to 15 percent efficient at converting sunlight to electricity, these advanced cells exhibit efficiencies approaching 23 percent. The increase in efficiency is due largely to the routing of electrical connections behind the cells (see Figure 2). This approach to increasing efficiency originated as a solution to the problem of maximizing the degree of utilization of the limited space available atop the wing of the Helios airplane. In retrospect, the solar cells in use at this site could be used on Helios, but the best cells otherwise commercially available could not be so used, because of their lower efficiencies. Historically, solar cells have been fabricated by use of methods that are common in the semiconductor industry. One of these methods includes the use of photolithography to define the rear electrical-contact features - diffusions, contact openings, and fingers. SunPower uses these methods to produce the advanced cells. To reduce fabrication costs, SunPower continues to explore new methods to define the rear electrical-contact features. The equipment at the demonstration site includes two fixed-angle solar arrays and one single-axis Sun-tracking array. One of the fixed arrays contains typical less-efficient commercial solar cells and is being used as a baseline for comparison of the other fixed array, which contains the advanced cells. The Sun-tracking array tilts to follow the Sun, using an advanced, real-time tracking device rather than customary pre-programmed mechanisms. Part of the purpose served by the demonstration is to enable determination of any potential advantage of a tracking array over a fixed array. The arrays are monitored remotely on a computer that displays pertinent information regarding the functioning of the arrays.

Creech, Gray↗