SEARCH · Search NASA

Results for “solid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1976

Analytical comparison of effects of solid-friction and viscous structural damping on panel flutter

A Galerkin modal analysis is presented that accounts for the effects of both solid friction and viscous structural damping on panel flutter, based on unsteady aerodynamic forces from supersonic potential flow. The eigensolutions are made by complex eigenvalue computer routines. Markedly different effects on the flutter boundary of the two types of structural damping are obtained. This result establishes that there is not, in general, an "equivalent viscous" damping for solid-friction damping. For the limiting case of the static-aerodynamic approximation, a substantially different flutter dynamic pressure is obtained for solid friction identically zero compared with solid friction approaching zero as a limit. Use of the quasi-static aerodynamic approximation eliminates that difference.

Cunningham, H. J.↗

NASA NTRS1976

Dynamics of solid lubrication as observed by optical microscopy

A bench metallograph was converted into a 'micro contact imager' by the addition of a tribometer employing a steel ball in sliding contact with a glass disk. The sliding contact was viewed in real time by means of projection microscope optics. The dynamics of abrasive particles and of solid lubricant particles within the contact were observed in detail. The contact was characterized by a constantly changing pattern of elastic strain with the passage of surface discontinuities and solid particles. Abrasive particles fragmented upon entering the contact, embedded in one surface and scratched the other; in contrast, the solid lubricant particles flowed plastically into thin films. The rheological behavior of the lubricating solids gave every appearance of a paste-like consistency within the Hertzian contact.

Sliney, H. E.↗

NASA NTRS1977

Gravity flow rate of solids through orifices and pipes

Lock-hopper systems are the most common means for feeding solids to and from coal conversion reactor vessels. The rate at which crushed solids flow by gravity through the vertical pipes and valves in lock-hopper systems affects the size of pipes and valves needed to meet the solids-handling requirements of the coal conversion process. Methods used to predict flow rates are described and compared with experimental data. Preliminary indications are that solids-handling systems for coal conversion processes are over-designed by a factor of 2 or 3.

Gardner, J. F.↗

NASA NTRS1977

Combustion response modeling for composite solid propellants

A computerized mathematical model of the combustion response function of composite solid propellants was developed with particular attention to the contributions of the solid phase heterogeneity. The one-dimensional model treats the solid phase as alternating layers of ammonium perchlorate and binder, with an exothermic melt layer at the surface. Solution of the Fourier heat equation in the solid provides temperature and heat flux distributions with space and time. The problem is solved by conserving the heat flux at the surface from that produced by a suitable model of the gas phase. An approximation of the BDP flame model is utilized to represent the gas phase. By the use of several reasonable assumptions, it is found that a significant portion of the problem can be solved in closed form. A method is presented by which the model can be applied to tetramodal particle size distributions. A computerized steady-state version of the model was completed, which served to validate the various approximations and lay a foundation for the combustion response modeling. The combustion response modeling was completed in a form which does not require an iterative solution, and some preliminary results were acquired.

Source record↗

NASA NTRS1979

Free energy of formation of Mo2C and the thermodynamic properties of carbon in solid molybdenum

As part of a study of the thermodynamical properties of interstitial elements in refractory metals, the free energy of formation of Mo2C is determined, and the thermodynamical properties of C in solution in solid Mo evaluated. The activity of C in the two-phase region Mo + Mo2C is obtained from the C content of iron rods equilibrated with metal + carbide powder mixtures. The free energy of formation of alpha-Mo2C is determined from the activity data. The thermodynamic properties of C in the terminal solid solution are calculated from available data on the solid solubility of C in Mo. Lattice distortion due to misfit of the C atoms in the interstitial sites appears to play a significant role in determining the thermodynamic properties of C in solid Mo.

Seigle, L. L.↗

NASA NTRS1980

Solid state SPS microwave generation and transmission study. Volume 1: Phase 2

The solid state sandwich concept for Solar Power Station (SPS) was investigated. The design effort concentrated on the spacetenna, but did include some system analysis for parametric comparison reasons. The study specifically included definition and math modeling of basic solid state microwave devices, an initial conceptual subsystems and system design, sidelobe control and system selection, an assessment of selected system concept and parametric solid state microwave power transmission system data relevant to the SPS concept. Although device efficiency was not a goal, the sensitivities to design of this efficiency were parametrically treated. Sidelobe control consisted of various single step tapers, multistep tapers, and Gaussian tapers. A preliminary assessment of a hybrid concept using tubes and solid state is also included. There is a considerable amount of thermal analysis provided with emphasis on sensitivities to waste heat radiator form factor, emissivity, absorptivity, amplifier efficiency, material and junction temperature.

Maynard, O. E.↗

NASA NTRS1980

Solid state SPS microwave generation and transmission study. Volume 2, phase 2: Appendices

The solid state sandwich concept for SPS was further defined. The design effort concentrated on the spacetenna, but did include some system analysis for parametric comparison reasons. Basic solid state microwave devices were defined and modeled. An initial conceptual subsystems and system design was performed as well as sidelobe control and system selection. The selected system concept and parametric solid state microwave power transmission system data were assessed relevant to the SPS concept. Although device efficiency was not a goal, the sensitivities to design of this efficiency were parametrically treated. Sidelobe control consisted of various single step tapers, multistep tapers and Gaussian tapers. A hybrid concept using tubes and solid state was evaluated. Thermal analyses are included with emphasis on sensitivities to waste heat radiator form factor, emissivity, absorptivity, amplifier efficiency, material and junction temperature.

Maynard, O. E.↗

NASA NTRS1981

Effects of solid particles suspended in fluid flow through an axial flow compressor stage

An approximate method for calculating the flow properties of gas-particle mixture flowing over blades in a cascade is studied. Using an analytical method, the solid particle trajectory and location of collisions between the solid particles and the blade surfaces are determined. In addition an experimental investigation of the trajectories and velocities of solid particles suspended in a fluid passing through an axial flow compressor cascade was performed. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand with average diameter of 165 microns. The following parameters were investigated: blade pressure distribution, and total pressure loss coefficient, both depending on the degree of erosion. In addition, a theoretical estimation of the blade erosion is compared with the experimental data.

Tabakoff, W.↗

NASA NTRS1980

SPS solid state antenna power combiner

Solid state dc-rf converters offer potential improvements in reliability, mass and low voltage operation, provided that anticipated efficiencies in excess of 80 percent can be realized. Field effect transistors offer the greatest potential in the SPS frequency band at 2.45 GHz. To implement this approach it is essential that means be found to sum the power of many relatively low power solid state sources in a low-loss manner, and that means be provided to properly control the phase of the outputs of the large number of solid state sources required. To avoid the power combining losses associated with circuit hybrids it was proposed that the power from multiple solid state amplifiers be combined by direct coupling of each amplifier's output to the radiating antenna structure. The selected power-combining antenna consists of a unique printed (metalized) microstrip circuit on a ceramic type dielectric substrate which is backed by a shallow lightweight aluminum cavity which sums the power of four microwave sources. The antenna behaves like two one-half wavelength slot-line antennas coupled together via their common cavity structure.

Fitzsimmons, G. W.↗

NASA NTRS1982

Turbulent boundary layer over solid and porous surfaces with small roughness

Skin friction and profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary layer were measured directly on a large diameter, axisymmetric body with: (1) a smooth, solid surface; (2) a sandpaper-roughened, solid surface; (3) a sintered metal, porous surface; (4) a smooth, perforated titanium surface; (5) a rough solid surface made of fine, diffusion bonded screening, and (6) a rough, porous surface of the same screening. Results obtained for each of these surfaces are discussed. It is shown that a rough, porous wall simply does not influence the boundary layer in the same way as a rough solid wall. Therefore, turbulent transport models for boundary layers over porous surfaces either with or without injection or suction, must include both surface roughness and porosity effects.

Kong, F. Y.↗

NASA NTRS1982

Basic investigation into the electrical performance of solid electrolyte membranes

The electrical performance of solid electrolyte membranes was investigated analytically and the results were compared with experimental data. It is concluded that in devices that are used for pumping oxygen the major power losses have to be attributed to the thin film electrodes. Relations were developed by which the effectiveness of tubular solid electrolyte membranes can be determined and the optimum length evaluated. The observed failure of solid electrolyte tube membranes in very localized areas is explained by the highly non-uniform current distribution in the membranes. The analysis points to a possible contact resistance between the electrodes and the solid electrolyte material. This possible contact resistance remains to be investigated experimentally. It is concluded that film electrodes are not appropriate for devices which operate with current flow, i.e., pumps though they can be employed without reservation in devices that measure oxygen pressures if a limited increase in the response time can be tolerated.

Richter, R.↗

NASA NTRS1982

Investigation of compositional segregation during unidirectional solidification of solid solution semiconducting alloys

Compositional segregation of solid solution semiconducting alloys in the radial direction during unidirectional solidification was investigated by calculating the effect of a curved solid liquid interface on solute concentration at the interface on the solid. The formulation is similar to that given by Coriell, Boisvert, Rehm, and Sekerka except that a more realistic cylindrical coordinate system which is moving with the interface is used. Analytical results were obtained for very small and very large values of beta with beta = VR/D, where V is the velocity of solidification, R the radius of the specimen, and D the diffusivity of solute in the liquid. For both very small and very large beta, the solute concentration at the interface in the solid C(si) approaches C(o) (original solute concentration) i.e., the deviation is minimal. The maximum deviation of C(si) from C(o) occurs for some intermediate value of beta.

Wang, J. C.↗

NASA NTRS1984

Status and New Directions for Solid Lubricant Coatings and Composite Materials

At one time, solid lubricants were used almost entirely in aerospace applications. Today there is a pronounced trend to use them over a much broader range of applications. For example, self-lubricating polymer-based composites have displaced traditional oil-lubricated, metallic composites for many journal bearings and thrust, washers in applications as diverse as earthmoving machinery and snow blowers to aircraft applications. For moderate temperatures below 200° C, glass filament-wound epoxy bearings with PTFE lubricating liners are useful; for temperatures up to 350° C, graphite fiber reinforced polyimide bearing materials are finding applications. Molybdenum disulfide, graphite, and PTFE are the most widely known and used solid lubricants, and there is increasing interest in the relatively new solid lubricant graphite fluoride. Advanced technology engines such as the adiabatic diesel and the small, efficient gas turbine have severe lubrication and wear problems at temperatures beyond the capabilities of any of these lubricants. Here, self-lubricating ceramics and inorganic composites for use at I000° C or higher are of interest. However, perhaps the most significant new direction for solid lubricant coatings and self-lubricating composites is their steadily increasing use in dry bearings for large volume, moderate temperature applications. This can be attributed to their simplicity of use (no supporting lubricant system needed), light weight, convenience, and general cost effectiveness.

Harold E Sliney↗

NASA NTRS1984

Accuracy of Three Dimensional Solid Finite Elements

The results of a study to determine the accuracy of the three dimensional solid elements available in NASTRAN for predicting displacements is presented. Of particular interest in the study is determining how to effectively use solid elements in analyzing thick optical mirrors, as might exist in a large telescope. Surface deformations due to thermal and gravity loading can be significant contributors to the determination of the overall optical quality of a telescope. The study investigates most of the solid elements currently available in either COSMIC or MSC NASTRAN. Error bounds as a function of mesh refinement and element aspect ratios are addressed. It is shown that the MSC solid elements are, in general, more accurate than their COSMIC NASTRAN counterparts due to the specialized numerical integration used. In addition, the MSC elements appear to be more economical to use on the DEC VAX 11/780 computer.

Case, W. R.↗

NASA NTRS1985

Apparatus and method to keep the walls of a free-space reactor free from deposits of solid materials

An apparatus and method is disclosed for keeping interior walls of a reaction vessel free of undesirable deposits of solid materials in gas-to-solid reactions. The apparatus includes a movable cleaning head which is configured to be substantially complementary to the interior contour of the walls of the reaction vessel. The head ejects a stream of gas with a relatively high velocity into a narrow space between the head and the walls. The head is moved substantially continuously to at least intermittently blow the stream of gas to substantially the entire surface of the walls wherein undesirable solid deposition is likely to occur. The disclosed apparatus and process is particularly useful for keeping the walls of a free-space silane-gas-to-solid-silicon reactor free of undesirable silicon deposits.

Yamakawa, K. A.↗

NASA NTRS1985

Solid-state Bonding of Superplastic Aluminum Alloy 7475 Sheet

Experimental works were carried out to study the feasibility of solid state bonding of superplastic aluminum 7475 sheet. Amount of deformation, bonding time, surface cleaning method and intermediate layer were the process parameters investigated. Other parameters, held constant by the superplastic forming condition which is required to obtain a concurrent solid state bonding, are bonding temperature, bonding pressure and atmosphere. Bond integrity was evaluated through metallographic examination, X-ray line scan analysis, SEM fractographic analysis and lap shear tests. The early results of the development program indicated that sound solid state bonding was accomplished for this high strength 7475 alloy with significant amounts of deformation. A thin intermediate layer of the soft 5052 aluminum alloy aided in achieving a solid state bonding by reducing the required amount of plastic deformation at the interface. Bond strength was substantially increased by a post bond heat treatment.

Byun, T. D. S.↗

NASA NTRS1983

Solid waste treatment processes for space station

The purpose of this study was to evaluate the state-of-the-art of solid waste(s) treatment processes applicable to a Space Station. From the review of available information a source term model for solid wastes was determined. An overall system is proposed to treat solid wastes under constraints of zero-gravity and zero-leakage. This study contains discussion of more promising potential treatment processes, including supercritical water oxidation, wet air (oxygen) oxidation, and chemical oxidation. A low pressure, batch-type treament process is recommended. Processes needed for pretreatment and post-treatment are hardware already developed for space operations. The overall solid waste management system should minimize transfer of wastes from their collection point to treatment vessel.

Marrero, T. R.↗

NASA NTRS1986

Display system software for the integration of an ADAGE 3000 programmable display generator into the solid modeling package C.A.D. software

A software system that integrates an ADAGE 3000 Programmable Display Generator into a C.A.D. software package known as the Solid Modeling Program is described. The Solid Modeling Program (SMP) is an interactive program that is used to model complex solid object through the composition of primitive geomeentities. In addition, SMP provides extensive facilities for model editing and display. The ADAGE 3000 Programmable Display Generator (PDG) is a color, raster scan, programmable display generator with a 32-bit bit-slice, bipolar microprocessor (BPS). The modularity of the system architecture and the width and speed of the system bus allow for additional co-processors in the system. These co-processors combine to provide efficient operations on and rendering of graphics entities. The resulting software system takes advantage of the graphics capabilities of the PDG in the operation of SMP by distributing its processing modules between the host and the PDG. Initially, the target host computer was a PRIME 850, which was later substituted with a VAX-11/785. Two versions of the software system were developed, a phase 1 and a phase 2. In phase 1, the ADAGE 3000 is used as a frame buffer. In phase II, SMP was functionally partitioned and some of its functions were implemented in the ADAGE 3000 by means of ADAGE's SOLID 3000 software package.

Montoya, R. J.↗