Search NASA⌕ Search

SEARCH · Search NASA

Results for “Batch processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

RINA: An interactive system for the rapid interpretation of NASTRAN results

RINA is a general post-processor system which performs data reduction, post processing and post analysis of NASTRAN results. RINA can be run in either batch or time-sharing mode. The system, which is an expansion of the NASDAT program, performs the following tasks: (1) scan of extreme values for displacements, forces, stresses and margins of safety, (2) computations of envelopes for displacements, forces, stresses and margins of safety, (3) computations of allowables and margins of safety; and (4) generation of NASTRAN tables needed for reanalysis computations. Usage of all these options provides the analyst with an efficient tool for the study and interpretation of NASTRAN analysis results and their presentation for project documentation.

Raibstone, A. I.↗
NASA NTRS1999

Effects of Fiber/Matrix Interface and its Composition on Mechanical Properties of Hi-Nicalon/Celsian Composites

To evaluate the effects of fiber coatings on composite mechanical properties. unidirectional celsian matrix composites reinforced with uncoated Hi-Nicalon fibers and those precoated with a dual BN/SiC layer in two separate batches (batch 1 and batch 2) were tested in three-point flexure. The uncoated-fiber reinforced composites showed catastrophic failure with strength of 210+/-35 MPa and a flat fracture surface. In contrast, composites reinforced with coated fibers exhibited graceful failure with extensive fiber pullout and showed significantly higher ultimate strengths, 904 and 759 MPa for the batch 1 and 2 coatings. respectively. Fiber push-in tests and microscopic examination indicated no chemical reaction at the uncoated or coated fiber-matrix interfaces that might be responsible for fiber strength degradation. Instead, the low strength of composite with uncoated fibers was due to degradation of the fiber strength from mechanical damage during composite processing. Despite identical processing, the first matrix cracking stresses (Sigma(sub mc)) of the composites reinforced with fibers coated in batch 1 and batch 2 were quite different, 436 and 122 MPa, respectively. The large difference in Sigma(sub mc) of the coated-fiber composites was attributed to differences in fiber sliding stresses (Tau(sub friction)), 121.2+/-48.7 and 10.4+/-3.1 MPa, respectively. for the two composites as determined by the fiber push-in method. Such a large difference in Tau(sub friction). for the two composites was found to be due to the difference in the compositions of the interface coatings. Scanning Auger microprobe analysis revealed the presence of carbon layers between the fiber and BN. and also between the BN and SiC coatings in the composite showing lower Tau(sub friction). This resulted in lower Sigma(sub mc) in agreement with the ACK theory. The ultimate strengths of the two composites depended mainly on the fiber volume fraction and were not significantly effected by Tau(sub friction) values, as expected. The poor reproducibility of the fiber coating composition between the two batches was judged to be the primary source of the large differences in performance of the two composites.

Bansal, Narottam P.↗
DOE OSTI2026

Chemical and Radiological Compatibility Testing of 3D Printed Materials

To dramatically increase the adaptability, performance, and safety of processes in support of the Defense Waste Processing Facility (DWPF), Savannah River National Lab (SRNL) plans to perform chemical and radiological compatibility testing on a wide variety of 3D printed materials of interest. The 3D printing process provides numerous strategic operational benefits such as rapid prototyping of complex designs and geometry specific to the needs of the nuclear waste disposition process, as well as on-demand rapid prototyping and iteration with materials that aren’t as accessible through traditional manufacturing methods. Reaction chemistry in simulated waste batches can be matched closely to its radioactive counterpart, but glass reactor vessels have limitations. Vessel geometry can play a big factor in mixing transport limitations, process chemistry, and degradation reaction kinetics. In addition, additive manufacturing allows for much more detailed vessel design than traditional alternatives. Waste processing techniques in DWPF also encounter extreme chemical environments including high pH, strong acids, abrasive slurries, and significant irradiation. To meet these challenges, a matrix of various polymer, ceramic, and metal additive manufacturing materials have been exposed to a suite of chemical environments of interest as well as radioactive dose (such as gamma radiation from 60 Co) to properly test their durability under these conditions. Mass change has been monitored over a period of up to a week in these conditions, as well as added characterization for surface modification through Scanning Electron Microscopy/Electron Dispersive X-ray analysis (SEM/EDX). Further chemical characterization has been monitored through Fourier-Transform InfraRed Spectroscopy (FTIR), with planned investigation via thermal and tensile strength degradation. While the direct product of this research is identification of material(s) that can withstand specific hazardous environments encountered by the mercury water wash tank in DWPF process simulation experiments, the reference base of materials will be used for many other nuclear processes in the pursuit of rapidly developed, cost-efficient, and highly specific devices for environmental remediation and much more.

Wilson, Nathan W. [Savannah River National Laborat↗
NASA NTRS1996

Processing and Properties of Fiber Reinforced Polymeric Matrix Composites: Processing Robustness of IM7/PETI Polyimide Composites - Part 2

The processability of a phenylethynyl terminated imide (PETI) resin matrix composite was investigated. Unidirectional prepregs were made by coating an N-methylpyrrolidone solution of the amide acid oligomer onto unsized IM7. Two batches of prepregs were used: one was made by NASA in-house, and the other was from an industrial source. The composite processing robustness was investigated with respect to the effect of B-staging conditions, the prepreg shelf life, and the optimal processing window. Rheological measurements indicated that PETI's processability was only slightly affected over a wide range of B-staging temperatures (from 250 C to 300 C). The open hole compression (OHC) strength values were statistically indistinguishable among specimens consolidated using various B-staging conditions. Prepreg rheology and OHC strengths were also found not to be affected by prolonged (i.e., up to 60 days) ambient storage. An optimal processing window was established using response surface methodology. It was found that IM7/PETI composite is more sensitive to the consolidation temperature than to the consolidation pressure. A good consolidation was achievable at 371 C/100 Psi, which yielded an OHC strength of 62 Ksi at room temperature. However, processability declined dramatically at temperatures below 350 C.

Hou, Tan-Hung↗
NASA NTRS2009

Carbon XANES Data from Six Aerogel Picokeystones Cut from the Top and Bottom Sides of the Stardust Comet Sample Tray

Great care and a large effort was made to minimize the amount of organic matter contained within the flight aerogel used to collect Comet 81P/Wild 2 samples. Even so, by the very nature of the production process and silica aerogel s affinity for volatile organics keeping silica aerogel free from organics is a monumental task. Silica aerogel from three production batches was flown on the Stardust sample return mission. All 3 types had layered densities varying from 5mg/ml to 50 mg/ml where the densest aerogel was farthest away from the collection area. A 2 step gelation process was used to make the flight aerogel and organics used in this process were tetraethylorthosilicate, ethanol and acetonitrile. Both ammonium hydroxide and nitric acid were also used in the aerogel production process. The flight aerogel was baked at JPL at 300 C for 72 hours, most of the baking was done at atmosphere but twice a day the oven was pumped to 10 torr for hour [1]. After the aerogel was baked it was stored in a nitrogen purged cabinet until flight time. One aerogel cell was located in the SRC away from any sample collection area as a witness to possible contamination from out gassing of the space craft, re-entry gases and any other organic encounter. This aerogel was aerogel used in the interstellar collection sample tray and is the least dense of the 3 batches of aerogel flown. Organics found in the witness tile include organics containing Si-CH3 bonds, amines and PAHS. Besides organic contamination, hot spots of calcium were reported in the flight aerogel. Carbonates have been detected in comet 81P/Wild2 samples . During preflight analyses, no technique was used to analyze for carbonates in aerogel. To determine if the carbonates found in 81P/Wild2 samples were from the comet, it is necessary to analyze the flight aerogel for carbonate as well as for organics.

Wirick, S.↗
DOE OSTI2024

Literature Review Investigating Adsorbents for Mercury Removal from Salt Batch Feed Material

The Savannah River Site (SRS) Liquid Waste System (LWS) contains mercury that originated from decades of canyon processing where it was used as a catalyst for dissolving aluminum cladding of reactor fuel. Since the start of radioactive operations, the Salt Waste Processing Facility (SWPF) has experienced processing difficulties due to the presence of mercury-laden solids. In response to these challenges, Savannah River National Laboratory (SRNL) has been requested by Savannah River Mission Completion (SRMC)/Salt Waste Processing Facility (SWPF) personnel to perform a literature review to assess the feasibility of chemical strikes to salt waste-containing tanks at the SRS as an option to reduce mercury introduction into SWPF. The literature review should evaluate known technologies and chemistries for decreasing mercury concentration and the anticipated efficacy of each technology on various mercury species known to exist in SRS waste.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1972

Design and development of a prototype wet oxidation system for the reclamation of water and the disposition of waste residues onboard space vehicles

Laboratory investigations to define optimum process conditions for oxidation of fecal/urine slurries were conducted in a one-liter batch reactor. The results of these tests formed the basis for the design, fabrication, and testing of an initial prototype system, including a 100-hour design verification test. Areas of further development were identified during this test. Development of a high pressure slurry pump, materials corrosion studies, oxygen supply trade studies, comparison of salt removal water recovery devices, ammonia removal investigation, development of a solids grinder, reactor design studies and bearing life tests, and development of shutoff valves and a back pressure regulator were undertaken. The development work has progressed to the point where a prototype system suitable for manned chamber testing can be fabricated and tested with a high degree of confidence of success.

Jagow, R. B.↗
NASA NTRS1982

Project Planning and Reporting

Project Planning Analysis and Reporting System (PPARS) is automated aid in monitoring and scheduling of activities within project. PPARS system consists of PPARS Batch Program, five preprocessor programs, and two post-processor programs. PPARS Batch program is full CPM (Critical Path Method) scheduling program with resource capabilities. Can process networks with up to 10,000 activities.

Source record↗
NASA NTRS1990

Evaluation of orbit determination using dual-TDRS tracking

This paper describes the results of a study to evaluate the orbit determinatioin of Tracking and Data Relay Satellite System (TDRSS) user spacecraft within the dual-Tracking and Data Relay Satellite (TDRS) environment. Dense TDRSS tracking of the Earth Radiation Budget Satellite (ERBS) was acquired for the period August 16 through 22, 1989. This tracking information was processed to evaluate the orbit determination consistency achieved using the Goddard Trajectory Determination System batch least-squares estimator. The effects of the use of the second operational relay spacecraft, of refinements in orbit determination models (geopotentials, polar motion, solid earth tidal gravitational perturbations, ionospheric refraction corrections), and of methods for providing relay spacecraft spacecraft position information were also studied.

Oza, D. H.↗
DOE OSTI2025

Hydrochlorination of Uranium Dioxide in a Molten Salt Mixture - Phase 1: Tube Furnace Cross Flow Experiments

In 2023, Metatomic® Inc., a South Carolina based company, was awarded a Gateway for Advanced Innovation in Nuclear (GAIN) research voucher for a proposed series of experiments aimed at demonstrating the viability of a spent nuclear fuel (SNF) recycling process patented by Met atomic® Inc. For the GAIN voucher, Metatomic® Inc. selected Savannah River National Laboratory (SRNL) as a partner in executing the proposed proof-of-concept experiments. This report outlines the proof-of-concept experiments performed by SRNL for Metatomic® Inc. during Phase 1 (of 2) experimentation. The Phase 1 hydrochlorination experiments consisted of weighing UO2 into alumina crucibles with a eutectic mixture of NaCl and CsCl, heating the uranium/salt mixture to a varied temperature (550, 650, or 750 °C), and flowing anhydrous hydrogen chloride (AHCl) gas across the surface of the uranium-bearing molten salt mixture. The hydrochlorination process conditions were maintained for 4-5 hours and the percent conversion for each batch of UO2 was determined using a suite of analytical characterization techniques. The degree of UO2 conversion was found to be greatest at the highest tested temperature, ultimately achieving 32.9% conversion of UO2 to water soluble uranium-chloro species (e.g., UO2Cl2, UCl4) after exposure to AHCl for 4.25 hours at 750 °C.

Nguyen, Vinh T. [Savannah River National Laborator↗
NASA NTRS1981

Coal desulfurization by low temperature chlorinolysis, phase 3

Laboratory scale, bench scale batch reactor, and minipilot plant tests were conducted on 22 bituminous, subbituminous, and lignite coals. Chemical pretreatment and post treatment of coals relative to the chlorination were tried as a means of enhancing desulfurization by the chlorinolysis process. Elevated temperature (500-700 C) hydrogen treatment of chlorinolysis-processed coal at atmospheric pressure was found to substantially increase coal desulfurization up to 90 percent. Sulfur forms, proximate and ultimate analyses of the processed coal are included. Minipilot plant operation indicates that the continuous flow reactor provides coal desulfurization results comparable to those obtained in the batch reactor. Seven runs were conducted at coal feed rates of 1.5 to 8.8 kg per hour using water and methylchloroform solvents, gaseous chlorine feed of 3 to 31.4 SCFH at 21 to 70 C, and atmospheric pressure for retention times of 20 to 120 minutes.

Kalvinskas, J. J.↗
NASA NTRS1994

Improved solution accuracy for TDRSS-based TOPEX/Poseidon orbit determination

Orbit determination results are obtained by the Goddard Space Flight Center (GSFC) Flight Dynamics Division (FDD) using a batch-least-squares estimator available in the Goddard Trajectory Determination System (GTDS) and an extended Kalman filter estimation system to process Tracking and Data Relay Satellite (TDRS) System (TDRSS) measurements. GTDS is the operational orbit determination system used by the FDD in support of the Ocean Topography Experiment (TOPEX)/Poseidon spacecraft navigation and health and safety operations. The extended Kalman filter was implemented in an orbit determination analysis prototype system, closely related to the Real-Time Orbit Determination System/Enhanced (RTOD/E) system. In addition, the Precision Orbit Determination (POD) team within the GSFC Space Geodesy Branch generated an independent set of high-accuracy trajectories to support the TOPEX/Poseidon scientific data. These latter solutions use the geodynamics (GEODYN) orbit determination system with laser ranging and Doppler Orbitography and Radiopositioning integrated by satellite (DORIS) tracking measurements. The TOPEX/Poseidon trajectories were estimated for November 7 through November 11, 1992, the timeframe under study. Independent assessments were made of the consistencies of solutions produced by the batch and sequential methods. The batch-least-squares solutions were assessed based on the solution residuals, while the sequential solutions were assessed based on primarily the estimated covariances. The batch-least-squares and sequential orbit solutions were compared with the definitive POD orbit solutions. The solution differences were generally less than 2 meters for the batch-least-squares and less than 13 meters for the sequential estimation solutions. After the sequential estimation solutions were processed with a smoother algorithm, position differences with POD orbit solutions of less than 7 meters were obtained. The differences among the POD, GTDS, and filter/smoother solutions can be traced to differences in modeling and tracking data types, which are being analyzed in detail.

Doll, C. E.↗
NASA NTRS2004

Processing Robustness for A Phenylethynyl Terminated Polyimide Composite

The processability of a phenylethynyl terminated imide resin matrix (designated as PETI-5) composite is investigated. Unidirectional prepregs are made by coating an N-methylpyrrolidone solution of the amide acid oligomer (designated as PETAA-5/NMP) onto unsized IM7 fibers. Two batches of prepregs are used: one is made by NASA in-house, and the other is from an industrial source. The composite processing robustness is investigated with respect to the prepreg shelf life, the effect of B-staging conditions, and the optimal processing window. Prepreg rheology and open hole compression (OHC) strengths are found not to be affected by prolonged (i.e., up to 60 days) ambient storage. Rheological measurements indicate that the PETAA-5/NMP processability is only slightly affected over a wide range of B-stage temperatures from 250 deg C to 300 deg C. The OHC strength values are statistically indistinguishable among laminates consolidated using various B-staging conditions. An optimal processing window is established by means of the response surface methodology. IM7/PETAA-5/NMP prepreg is more sensitive to consolidation temperature than to pressure. A good consolidation is achievable at 371 deg C (700 deg F)/100 Psi, which yields an RT OHC strength of 62 Ksi. However, processability declines dramatically at temperatures below 350 deg C (662 deg F), as evidenced by the OHC strength values. The processability of the IM7/LARC(TM) PETI-5 prepreg was found to be robust.

Hou, Tan-Hung↗
DOE OSTI2026

Vision and Development of a Design, Implementation, and Verification Automation (DIVA) Software Platform for DNA Construction

Abstract DNA construction, while a prerequisite to many biological endeavors, is often a time-consuming distraction from an individual’s primary research objectives. We envisioned that with the right software infrastructure and cultural mindset, a single person could execute in parallel the batched DNA construction tasks of an entire research institute, at scales realizing efficiency gains through process and laboratory automation. In pursuit of this vision, we developed the Design, Implementation, and Verification Automation (DIVA) software platform. DIVA’s web interface enables researchers to design DNA constructs (using visual biological computer-aided design tools and biological parts repositories), submit designs for construction to dedicated staff, and track DNA construction as it progresses. DIVA supports the dedicated staff through the DNA construction process and records both successful and unsuccessful attempts toward improving the overall process. The platform is publicly available at public-diva.jbei.org and its open-source code through github.com/JBEI/DIVA.

Plahar, Hector [DOE Agile BioFoundry , , ,; DOE Jo↗
DOE OSTI2025

Report on Updated Properties Handbook of Printed Stainless Steel 316

This report focuses on summarizing mechanical behavior of 316H stainless steel (SS) printed using laser powder bed fusion (LPBF). 316H SS is one of the six alloys that has been qualified for use in nuclear reactors. The Advanced Materials and Manufacturing Technologies (AMMT) program has identified the use of the additive manufacturing (AM) process of LPBF as one of the manufacturing modalities to fabricate components for nuclear applications. Unlike wrought material, AM material displays significant heterogeneity in properties, resulting from changes in process parameters, machine-to-machine variability, and minor changes in feedstock chemistry from one batch to another. Although significant work has been done on 316L SS in the literature and has been summarized in several review papers, very limited data exist on 316H SS. Therefore, this report aims to provide a concise summary of the properties of 316H SS printed using different machines and at different locations as a part of the AMMT program.

36 MATERIALS SCIENCE↗
NASA NTRS2003

High Temperature Transfer Molding Resins: Status of PETI-298 and PETI-330

Two phenylethynyl terminated oligomers designated PETI-298 and PETI-330 were developed at the NASA Langley Research Center and have emerged as leading candidates for composite applications requiring high temperature performance (i.e. greater than or equal to 288 C for 1000 hours) combined with the ability to be readily processed into composites without the use of an autoclave or complex/lengthy cure or post-cure cycle. These high performance/high temperature composites are potentially useful on advanced aerospace vehicles in structural applications and as aircraft engine components such as inlet frames and compressor vanes. The number designation (i.e. 298, 330) refers to the glass transition temperature in degrees Celsius as determined on neat resin cured for 1 hour at 371 C. The resins are processable by non-autoclave techniques such as resin transfer molding (RTM), vacuum assisted RTM (VARTM) and resin infusion (RI). Both resins exhibit low complex melt viscosities (0.1-10 poise) at 280 C and are stable for greater than or equal to 2 hours at this temperature. Typically, the resins are melted, de-gassed and infused or injected at 280 C and subsequently cured at 371 C for 1-2 hours. Virtually no volatiles are evolved during the cure process. The resin synthesis is straightforward and has been scaled-up to 25 kg batches. The chemistry of PETI-298 and PETI-330 and the RTM AS-4 and T-650 carbon fabric laminate properties, and those of BMI-5270 for comparison, are presented.

Connell, John W.↗
NASA NTRS1997

Effects of Bioreactor Retention Time on Aerobic Microbial Decomposition of CELSS Crop Residues

The focus of resource recovery research at the KSC-CELSS Breadboard Project has been the evaluation of microbiologically mediated biodegradation of crop residues by manipulation of bioreactor process and environmental variables. We will present results from over 3 years of studies that used laboratory- and breadboard-scale (8 and 120 L working volumes, respectively) aerobic, fed-batch, continuous stirred tank reactors (CSTR) for recovery of carbon and minerals from breadboard grown wheat and white potato residues. The paper will focus on the effects of a key process variable, bioreactor retention time, on response variables indicative of bioreactor performance. The goal is to determine the shortest retention time that is feasible for processing CELSS crop residues, thereby reducing bioreactor volume and weight requirements. Pushing the lower limits of bioreactor retention times will provide useful data for engineers who need to compare biological and physicochemical components. Bioreactor retention times were manipulated to range between 0.25 and 48 days. Results indicate that increases in retention time lead to a 4-fold increase in crop residue biodegradation, as measured by both dry weight losses and CO2 production. A similar overall trend was also observed for crop residue fiber (cellulose and hemicellulose), with a noticeable jump in cellulose degradation between the 5.3 day and 10.7 day retention times. Water-soluble organic compounds (measured as soluble TOC) were appreciably reduced by more than 4-fold at all retention times tested. Results from a study of even shorter retention times (down to 0.25 days), in progress, will also be presented.

Strayer, R. F.↗
DOE OSTI2025

Advancing continuous enzymatic hydrolysis for improved biomass saccharification

Background: A deployable, continuous enzymatic hydrolysis (CEH) process can address cost and commercialization risks associated with second-generation (Gen2) biorefinery sugar/lignin/ethanol production while contributing to energy supply and security. Developments in commercial enzymatic hydrolysis formulations targeting Gen2 pretreated biomass such as deacetylated mechanically refined (DMR) biomass necessitate a reassessment of the existing hybrid simultaneous saccharification and fermentation (SSF) approach. Notably, the practice of "finishing hydrolysis" in SSF has become problematic with the introduction of oxidative enzymes, such as lytic polysaccharide monooxygenases (LPMOs), into commercial cellulase formulations as these require specific redox conditions and cofactor. Moreover, continuous SSF has not been demonstrated at commercial scale, limiting deployment and the associated economic benefits to farmers, producers, and support industries. Results: Continuous enzymatic hydrolysis (CEH) was demonstrated at bench scale to enable optimal saccharification performance of deacetylated mechanically refined (DMR) pretreated biomass. Diafiltration was demonstrated to retain pretreated biomass solids and enzymes for continuous reaction while removing solubilized product sugars in situ. A significant breakthrough afforded by the CEH process is its ability to achieve equivalent endpoint conversions with approximately 50% lower enzyme loading. Yields of glucose and xylose were increased ~ 15% and ~ 4%, respectively, over batch hydrolysis. Unlike SSF using yeast or Zymomonas, CEH allows precise optimization of pH, temperature, oxygen tension, LPMO mediator concentration, and removal of end-product inhibitors. Conclusions: Advanced CEH holds promise as a transformational, process-intensified, and cost-effective method for producing soluble clarified biomass sugars and insoluble lignin-rich streams. Enhancing saccharification performance, optimizing operating parameters, and employing membrane filtration will help overcome existing challenges and enable the efficient production of valuable biomaterials from lignocellulosic biomass.

09 BIOMASS FUELS↗