Search NASA⌕ Search

SEARCH · Search NASA

Results for “CASE METHOD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Temperatures and Stresses on Hollow Blades For Gas Turbines

The present treatise reports on theoretical investigations and test-stand measurements which were carried out in the BMW Flugmotoren GMbH in developing the hollow blade for exhaust gas turbines. As an introduction the temperature variation and the stress on a turbine blade for a gas temperature of 900 degrees and circumferential velocities of 600 meters per second are discussed. The assumptions onthe heat transfer coefficients at the blade profile are supported by tests on an electrically heated blade model. The temperature distribution in the cross section of a blade Is thoroughly investigated and the temperature field determined for a special case. A method for calculation of the thermal stresses in turbine blades for a given temperature distribution is indicated. The effect of the heat radiation on the blade temperature also is dealt with. Test-stand experiments on turbine blades are evaluated, particularly with respect to temperature distribution in the cross section; maximum and minimum temperature in the cross section are ascertained. Finally, the application of the hollow blade for a stationary gas turbine is investigated. Starting from a setup for 550 C gas temperature the improvement of the thermal efficiency and the fuel consumption are considered as well as the increase of the useful power by use of high temperatures. The power required for blade cooling is taken into account.

Pollmann, Erich↗
NASA NTRS2003

Test Rig for Evaluating Active Turbine Blade Tip Clearance Control Concepts

Improved blade tip sealing in the high pressure compressor and high pressure turbine can provide dramatic improvements in specific fuel consumption, time-on-wing, compressor stall margin and engine efficiency as well as increased payload and mission range capabilities of both military and commercial gas turbine engines. The preliminary design of a mechanically actuated active clearance control (ACC) system for turbine blade tip clearance management is presented along with the design of a bench top test rig in which the system is to be evaluated. The ACC system utilizes mechanically actuated seal carrier segments and clearance measurement feedback to provide fast and precise active clearance control throughout engine operation. The purpose of this active clearance control system is to improve upon current case cooling methods. These systems have relatively slow response and do not use clearance measurement, thereby forcing cold build clearances to set the minimum clearances at extreme operating conditions (e.g., takeoff, re-burst) and not allowing cruise clearances to be minimized due to the possibility of throttle transients (e.g., step change in altitude). The active turbine blade tip clearance control system design presented herein will be evaluated to ensure that proper response and positional accuracy is achievable under simulated high-pressure turbine conditions. The test rig will simulate proper seal carrier pressure and temperature loading as well as the magnitudes and rates of blade tip clearance changes of an actual gas turbine engine. The results of these evaluations will be presented in future works.

Lattime, Scott B.↗
NASA NTRS1998

Clinical use of three-dimensional video measurements of eye movements

Noninvasive measurements of three-dimensional eye position can be accurately achieved with video methods. A case study showing the potential clinical benefit of these enhanced measurements is presented along with some thoughts about technological advances, essential for clinical application, that are likely to occur in the next several years.

Non-NASA Center↗
NASA NTRS2006

Improved target handoff for single cycle instrument placement

Single Cycle Instrument Placement(SCIP)could dramatically increase the speed of various planetary rover operations. JPL is validating SCIP for use on its upcoming Mars Science Laboratory mission. Two major sources of error in the implementation submitted for validation were imprecision in selecting a distant target and error introduced while handing the target off to the rover's hazard cameras (hazcams). We have added the capability to designate a target using high resolution cameras (pancams) and then hand off to medium resolution cameras (navcams) with little error later in the traverse. We implemented several options for handoff from navcams to hazcams. We evaluated their performance on several test cases. Two methods produced average handoff error of 1 pixel when successful, but these only worked in half of the tests. Two other methods reliably produced about 10 pixels of error. None reliably reach the goal of 1 pixel handoff accuracy.

handoff↗
NASA NTRS2014

The Virtual Observatory Service TheoSSA: Establishing a Database of Synthetic Stellar Flux Standards II. NLTE Spectral Analysis of the OB-Type Subdwarf Feige 110

Context. In the framework of the Virtual Observatory (VO), the German Astrophysical VO (GAVO) developed the registered service TheoSSA (Theoretical Stellar Spectra Access). It provides easy access to stellar spectral energy distributions (SEDs) and is intended to ingest SEDs calculated by any model-atmosphere code, generally for all effective temperatures, surface gravities, and elemental compositions. We will establish a database of SEDs of flux standards that are easily accessible via TheoSSA's web interface. Aims. The OB-type subdwarf Feige 110 is a standard star for flux calibration. State-of-the-art non-local thermodynamic equilibrium stellar-atmosphere models that consider opacities of species up to trans-iron elements will be used to provide a reliable synthetic spectrum to compare with observations. Methods. In case of Feige 110, we demonstrate that the model reproduces not only its overall continuum shape from the far-ultraviolet (FUV) to the optical wavelength range but also the numerous metal lines exhibited in its FUV spectrum. Results. We present a state-of-the-art spectral analysis of Feige 110. We determined Teff =47 250 +/- 2000 K, log g=6.00 +/- 0.20, and the abundances of He, N, P, S, Ti, V, Cr, Mn, Fe, Co, Ni, Zn, and Ge. Ti, V, Mn, Co, Zn, and Ge were identified for the first time in this star. Upper abundance limits were derived for C, O, Si, Ca, and Sc. Conclusions. The TheoSSA database of theoretical SEDs of stellar flux standards guarantees that the flux calibration of astronomical data and cross-calibration between different instruments can be based on models and SEDs calculated with state-of-the-art model atmosphere codes.

Observatory↗
NASA NTRS2015

Current Practices in Constructing and Evaluating Assurance Cases With Applications to Aviation

This report introduces and provides an overview of assurance cases including theory, practice, and evaluation. This report includes a section that introduces the principles, terminology, and history of assurance cases. The core of the report presents twelve example uses of assurance cases from a range of domains, using a novel classification scheme. The report also reviews the state of the art in assurance case evaluation methods.

David J Rinehart↗
NASA NTRS2015

Estimates of Power Plant NOx Emissions and Lifetimes from OMI NO2 Satellite Retrievals

Isolated power plants with well characterized emissions serve as an ideal test case of methods to estimate emissions using satellite data. In this study we evaluate the Exponentially-Modified Gaussian (EMG) method and the box model method based on mass balance for estimating known NOx emissions from satellite retrievals made by the Ozone Monitoring Instrument (OMI). We consider 29 power plants in the USA which have large NOx plumes that do not overlap with other sources and which have emissions data from the Continuous Emission Monitoring System (CEMS). This enables us to identify constraints required by the methods, such as which wind data to use and how to calculate background values. We found that the lifetimes estimated by the methods are too short to be representative of the chemical lifetime. Instead, we introduce a separate lifetime parameter to account for the discrepancy between estimates using real data and those that theory would predict. In terms of emissions, the EMG method required averages from multiple years to give accurate results, whereas the box model method gave accurate results for individual ozone seasons.

Emissions inventory↗
NASA NTRS2016

Lunar Entry Downmode Options for Orion

For Exploration Missions 1 and 2, the Orion capsules will be entering the Earth's atmosphere with speeds in excess of 11 km/s. In the event of a degraded Guidance, Navigation, and Control system, attempting the nominal guided entry may be inadvisable due to the potential for failures that result in a loss of vehicle (or crew, when crew are aboard). In such a case, a method of assuring Earth capture, water landing, and observence of trajectory constraints (heating, loads) is desired. Such a method should also be robust to large state uncertainty and variations in entry interface states. This document will explore four approaches evaluated and their performance in ensuring a safe return of the Orion capsule in the event of onboard system degradation.

Smith, Kelly M.↗
NASA NTRSDate not supplied

A Comparison of Two Non-Contact Strain Measurement Techniques with Applications to Scientific Balloons

Strain measurements of scientific balloon films are necessary for evaluating the film’s material properties, validating material models, and structural evaluations of scale model balloons. This paper presents a comparison of the strain measurement techniques used by the Balloon Program Office’s Balloon Research and Development Lab at NASA Wallops Flight Facility. Two non-contact strain measurement techniques are presented for comparison, along with an assessment of measurement accuracy for both methods. The case study of a vertically oriented cylindrical balloon is presented to illustrate both systems’ performance and draw nominal conclusions of strain as a function of pressure and axial load.

Non-Contact↗
NASA NTRSDate not supplied

A Comparison of Two Non-Contact Strain Measurement Techniques with Applications to Scientific Balloons

Strain measurements of scientific balloon films are necessary for evaluating the film’s material properties, validating material models, and structural evaluations of scale model balloons. This paper presents a comparison of the strain measurement techniques used by the Balloon Program Office’s Balloon Research and Development Lab at NASA Wallops Flight Facility. Two non-contact strain measurement techniques are presented for comparison, along with an assessment of measurement accuracy for both methods. The case study of a vertically oriented cylindrical balloon is presented to illustrate both systems’ performance and draw nominal conclusions of strain as a function of pressure and axial load.

Non-Contact↗
NASA NTRSDate not supplied

Medium-Fidelity CFD Modeling of Multicopter Wakes for Airborne Sensor Measurements

A steady-state multicopter simulation capability leveraging automated Cartesian grid generation and a blade element source term rotor model was used to investigate multi-rotor aerodynamics in and out of ground effect. Simulations demonstrated that this model is able to predict reasonably accurate thrust in ground effect for both single and multiple propeller cases. The method yielded accurate lift and drag predictions for a commercial quadcopter when compared to recent wind tunnel test data. This aircraft was then simulated in a variety of flight conditions, including both hover and edgewise forward flight, to determine if generalized guidelines for airborne sensor placement could be developed. Velocity perturbation magnitudes showed large regions of affected air upstream of the vehicle at low speeds, which contracted as the vehicle’s speed was increased. Placing the sensors more than one characteristic length ahead of or above the aircraft reduces errors from rotor-induced flow at higher speeds. For low-speed forward flight, the entrainment of flow into the propeller wakes introduces significant flow turning above the aircraft, suggesting that a forward location, with more moderate perturbations, could be advantageous for these conditions.

ARMD↗
DOE OSTI2021

Pressurized damping fluid injection for damping turbine blade vibration

A blade vibration damping system impacts a pressurized damping fluid on a surface of at least one of a plurality of blades of a turbine in opposition to a vibratory movement thereof to cause damping of vibration of the blade(s) during operation of the turbine. The system includes a fluid injection nozzle in a stationary component adjacent the plurality of blades. A valve selectively admits the pressurized damping fluid to the fluid injection nozzle from a source of pressurized damping fluid, and a control system controls the valve to operate the fluid injection nozzle in response to an operational parameter exceeding a threshold during operation of the turbine. A related turbine casing and method are also provided.

Delvaux, John McConnell↗
DOE OSTI2022

Electrical Substation Configuration Effect on Substation Reliability

It is crucial that the U.S. electrical grid be reliable, due to its critical role in the economy and our national defense/security. Many common tasks and industrial operations rely on proper electrical power distribution. In designing new bus systems or evaluating existing ones, the type of configuration employed affects the level of risk, reliability, maintenance, and cost involved. The present work utilizes Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) to perform a probabilistic risk assessment (PRA)-based sensitivity study on substation reliability in regard to different bus configurations. This study examines single bus, main and transfer, breaker and a half, double bus/double breaker, and ring bus configurations applied to busses with different numbers of lines. The case variances, methods, and rankings presented herein can help guide bus configurations for electrical grid design/analysis in the future.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Electrical Substation Configuration Effect on Substation Reliability

The nation’s electrical grid must be reliable because of its critical role in the economy, defense, and security of the nation. Many common tasks and industrial operations rely on proper electrical power distribution. In the design of new bus systems or evaluation of existing bus systems, the type of bus configuration affects the risk, reliability, maintenance, and cost of the system. This work utilizes Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) to perform a probabilistic risk assessment (PRA) based sensitivity study on the reliability of substations with differing bus configurations. This study examines single bus, main and transfer, breaker and a half, double bus/double breaker, and ring bus configurations applied to busses of varying number of lines. The case variances, methods, and rankings presented can provide a guide for bus configuration for future electrical grid design and analysis.

24 POWER TRANSMISSION AND DISTRIBUTION↗