Search NASA⌕ Search

SEARCH · Search NASA

Results for “micromechanical analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Composite blade structural analyzer (COBSTRAN) user's manual

The installation and use of a computer code, COBSTRAN (COmposite Blade STRuctrual ANalyzer), developed for the design and analysis of composite turbofan and turboprop blades and also for composite wind turbine blades was described. This code combines composite mechanics and laminate theory with an internal data base of fiber and matrix properties. Inputs to the code are constituent fiber and matrix material properties, factors reflecting the fabrication process, composite geometry and blade geometry. COBSTRAN performs the micromechanics, macromechanics and laminate analyses of these fiber composites. COBSTRAN generates a NASTRAN model with equivalent anisotropic homogeneous material properties. Stress output from NASTRAN is used to calculate individual ply stresses, strains, interply stresses, thru-the-thickness stresses and failure margins. Curved panel structures may be modeled providing the curvature of a cross-section is defined by a single value function. COBSTRAN is written in FORTRAN 77.

Aiello, Robert A.↗
DOE OSTI2021

Direct observations and characterization of crack closure during microstructurally small fatigue crack growth via in-situ high-energy X-ray characterization

This study provides direct observation of the crack closure mechanism of a naturally occurring, tortuous, 3D microstructurally small fatigue crack (SFC) in additively manufactured Inconel 718. In-situ non-destructive characterization is performed using high-energy X-ray diffraction techniques to capture the evolution of the 3D microstructure and micromechanical response in the vicinity of the crack front. Based on the stress state of twelve grains analyzed at the crack tip, the crack closure events of the SFC front was found to be spatially heterogeneous with respect to loading progression governed by the local stress state of the grains (specifically the stress reversal from compression to tension). From this analysis, three grains that displayed different degrees of crack closure were further investigated, based on the orientation of the crack relative to the grains and the associated modality of crack growth. The stress normal to the crack plane and the associated degree of Mode I crack behavior were correlated with events of the crack opening earlier during the loading cycle. This was further corroborated by diffraction spot spreading analysis that quantified the crystallographic lattice distortion caused by the opening crack. Additionally, the detailed characterization of the opening behavior of the grains located at the crack tip and their associated states of stress elucidates the mechanism governing crack closure and will inform future modeling efforts of this phenomenon.

36 MATERIALS SCIENCE↗
NASA NTRS2015

Experimental and Numerical Analysis of Triaxially Braided Composites Utilizing a Modified Subcell Modeling Approach

A combined experimental and analytical approach was performed for characterizing and modeling triaxially braided composites with a modified subcell modeling strategy. Tensile coupon tests were conducted on a [0deg/60deg/-60deg] braided composite at angles of 0deg, 30deg, 45deg, 60deg and 90deg relative to the axial tow of the braid. It was found that measured coupon strength varied significantly with the angle of the applied load and each coupon direction exhibited unique final failures. The subcell modeling approach implemented into the finite element software LS-DYNA was used to simulate the various tensile coupon test angles. The modeling approach was successful in predicting both the coupon strength and reported failure mode for the 0deg, 30deg and 60deg loading directions. The model over-predicted the strength in the 90deg direction; however, the experimental results show a strong influence of free edge effects on damage initiation and failure. In the absence of these local free edge effects, the subcell modeling approach showed promise as a viable and computationally efficient analysis tool for triaxially braided composite structures. Future work will focus on validation of the approach for predicting the impact response of the braided composite against flat panel impact tests.

Micromechanics↗
NASA NTRS1989

A study of material damping in large space structures

A constitutive model was developed for predicting damping as a function of damage in continuous fiber reinforced laminated composites. The damage model is a continuum formulation, and uses internal state variables to quantify damage and its subsequent effect on material response. The model is sensitive to the stacking sequence of the laminate. Given appropriate baseline data from unidirectional material, and damping as a function of damage in one crossply laminate, damage can be predicted as a function of damage in other crossply laminates. Agreement between theory and experiment was quite good. A micromechanics model was also developed for examining the influence of damage on damping. This model explicitly includes crack surfaces. The model provides reasonable predictions of bending stiffness as a function of damage. Damping predictions are not in agreement with the experiment. This is thought to be a result of dissipation mechanisms such as friction, which are not presently included in the analysis.

Highsmith, A. L.↗
NASA NTRS2002

Computational Simulation of the High Strain Rate Tensile Response of Polymer Matrix Composites

A research program is underway to develop strain rate dependent deformation and failure models for the analysis of polymer matrix composites subject to high strain rate impact loads. Under these types of loading conditions, the material response can be highly strain rate dependent and nonlinear. State variable constitutive equations based on a viscoplasticity approach have been developed to model the deformation of the polymer matrix. The constitutive equations are then combined with a mechanics of materials based micromechanics model which utilizes fiber substructuring to predict the effective mechanical and thermal response of the composite. To verify the analytical model, tensile stress-strain curves are predicted for a representative composite over strain rates ranging from around 1 x 10(exp -5)/sec to approximately 400/sec. The analytical predictions compare favorably to experimentally obtained values both qualitatively and quantitatively. Effective elastic and thermal constants are predicted for another composite, and compared to finite element results.

Goldberg, Robert K.↗
NASA NTRS1994

The Relationship Between Constraint and Ductile Fracture Initiation as Defined by Micromechanical Analyses

The use of small laboratory specimens to predict the integrity of large, complex structures relies on the validity of single parameter fracture mechanics. Unfortunately, the constraint loss associated with large scale yielding, whether in a laboratory specimen because of its small size or in a structure because it contains shallow flaws loaded in tension, can cause the breakdown of classical fracture mechanics and the loss of transferability of critical, global fracture parameters. Although the issue of constraint loss can be eliminated by testing actual structural configurations, such an approach can be prohibitively costly. Hence, a methodology that can correct global fracture parameters for constraint effects is desirable. This research uses micromechanical analyses to define the relationship between global, ductile fracture initiation parameters and constraint in two specimen geometries (SECT and SECB with varying a/w ratios) and one structural geometry (circumferentially cracked pipe). Two local fracture criteria corresponding to ductile fracture micromechanisms are evaluated: a constraint-modified, critical strain criterion for void coalescence proposed by Hancock and Cowling and a critical void ratio criterion for void growth based on the Rice and Tracey model. Crack initiation is assumed to occur when the critical value in each case is reached over some critical length. The primary material of interest is A516-70, a high-hardening pressure vessel steel sensitive to constraint; however, a low-hardening structural steel that is less sensitive to constraint is also being studied. Critical values of local fracture parameters are obtained by numerical analysis and experimental testing of circumferentially notched tensile specimens of varying constraint (e.g., notch radius). These parameters are then used in conjunction with large strain, large deformation, two- and three-dimensional finite element analyses of the geometries listed above to predict crack initiation loads and to calculate the associated (critical) global fracture parameters. The loads are verified experimentally, and microscopy is used to measure pre-crack length, crack tip opening displacement (CTOD), and the amount of stable crack growth. Results for A516-70 steel indicate that the constraint-modified, critical strain criterion with a critical length approximately equal to the grain size (0.0025 inch) provides accurate predictions of crack initiation. The critical void growth criterion is shown to considerably underpredict crack initiation loads with the same critical length. The relationship between the critical value of the J-integral for ductile crack initiation and crack depth for SECT and SECB specimens has been determined using the constraint-modified, critical strain criterion, demonstrating that this micromechanical model can be used to correct in-plane constraint effects due to crack depth and bending vs. tension loading. Finally, the relationship developed for the SECT specimens is used to predict the behavior of circumferentially cracked pipe specimens.

Panontin, Tina L.↗
DOE OSTI2020

Quantifying the resistance to dislocation glide in single phase FeCrAl alloy

The resistance to dislocation glide associated with slip systems {110}<111> and {112}<111> in single phase FeCrAl alloy is measured via micromechanical testing in a scanning electronic microscopy at room temperature. Two important factors, the shape and orientation of a pillar, are discussed with respect to the glide resistance and stress-strain response. Maximizing Schmid factor of one specific slip system while minimizing others is recommended in order to diminish obvious dislocations-induced hardening during in-situ testing. Apparent Schmid factor analysis is conducted to select grains with preferred orientations. Two types of pillars with conventional cylindrical shape or dog-bone shape are tested under compression to estimate the resistance to dislocation glide and evaluate the effect of pillar shape on the compression stress-strain response. One dog-bone pillar is tested under tension to check the tension-compression isotropy of dislocation slip. We discover that the shape of a pillar to a smaller extent affects the measured resistance but strongly influences the stress strain response. Cylindrical pillars exhibit apparent hardening associated with early yielding due to stress or strain concentration at contact region, while dog-bone pillars show an obvious yielding and continuous shearing without hardening. The resistance is 220 MPa for slip system {110}<111> and 230 MPa for slip system {112}<111>. Finite element analysis is performed to account for the influence of pillar shape and contact condition on mechanical response.

36 MATERIALS SCIENCE↗
NASA NTRS2026

Micromechanical Design of Carbon Nanotube Ribbon Reinforced Polymer Composite Materials

Lightweight materials are an important component of the design of aerospace structures. Carbon nanotube materials have been considered for this purpose due to the strength and stiffness of individual nanotubes, and the commercial availability of bulk formats such as fibers. These fibers can have a ribbon cross section which results in a different design space for their composites relative to traditional reinforcements which have a round cross section. This work applies brick-and-mortar micromechanical models and classical lamination theory with an inverse approach to investigate the design space of these composites. Using this approach, the influences of fiber geometry and axial and transverse mechanical properties are mapped. Finally, a sensitivity study is performed and the relative impacts of ±10% variations in the constituent material and geometric properties are ranked. Lamina axial moduli were found to range from a maximum of 3x to 1x minimum relative to a target quasi-isotropic laminate modulus depending on the anisotropy and shear modulus of the lamina. The fiber targets depended strongly on the fiber volume fraction in the lamina and the fiber axial modulus target was found to range from 4.8x to 3.2x the quasi-isotropic laminate target. The sensitivity analysis found that the largest driver of performance was the volume fraction, followed by the fiber axial modulus. While bio-based brick-and-mortar composites, such as nacre, can benefit from reinforcement aspect ratios above 10, for carbon nanotube ribbon (or carbon fiber)/polymer composites the sensitivity study indicated that the optimal cross-sectional aspect ratio was relatively smaller, potentially less than three.

Micromechanics↗
NASA NTRS2015

Experimental and Numerical Analysis of Triaxially Braided Composites Utilizing a Modified Subcell Modeling Approach

A combined experimental and analytical approach was performed for characterizing and modeling triaxially braided composites with a modified subcell modeling strategy. Tensile coupon tests were conducted on a [0deg/60deg/-60deg] braided composite at angles [0deg, 30deg, 45deg, 60deg and 90deg] relative to the axial tow of the braid. It was found that measured coupon strength varied significantly with the angle of the applied load and each coupon direction exhibited unique final failures. The subcell modeling approach implemented into the finite element software LS-DYNA was used to simulate the various tensile coupon test angles. The modeling approach was successful in predicting both the coupon strength and reported failure mode for the 0deg, 30deg and 60deg loading directions. The model over-predicted the strength in the 90deg direction; however, the experimental results show a strong influence of free edge effects on damage initiation and failure. In the absence of these local free edge effects, the subcell modeling approach showed promise as a viable and computationally efficient analysis tool for triaxially braided composite structures. Future work will focus on validation of the approach for predicting the impact response of the braided composite against flat panel impact tests.

Polymer Matrix Composites↗
NASA NTRS2006

STRANAL-PMC Version 2.0

Version 2.0 of the Strain Rate Dependent Analysis of Polymer Matrix Composites (STRANAL-PMC) software has been released. A prior version was reported in Analyzing Loads and Strains in Polymer- Matrix Composites (LEW-17227), NASA Tech Briefs, Vol. 26, No. 11 (November 2002), page 36. To recapitulate: Modified versions of constitutive equations of viscoplasticity of metals are used to represent deformation of a polymeric matrix. The equations are applied in a micromechanical approach, proceeding upward from slices of unit cells, through the ply level, to the laminate level. The constitutive equations are integrated in time by a Runge- Kutta technique. To predict the ultimate strength of each composite ply, failure criteria are implemented within the micromechanics. The inputs to STRANAL-PMC are the laminate geometry, properties of the fiber and matrix materials, and applied stress or strain versus time. The outputs are time-dependent stresses and strains at the slice, ply, and laminate levels. The improvements in version 2.0 include more rigorous representation of hydrostatic- stress effects in the matrix, refinement and extension of ply failure models, and capabilities to analyze transverse shear stresses. Version 2.0 can be implemented as a material-model code within transient dynamic finite-element codes.

Goldberg, Robert↗
NASA NTRS1995

On the Finite Element Implementation of the Generalized Method of Cells Micromechanics Constitutive Model

The Generalized Method of Cells (GMC), a micromechanics based constitutive model, is implemented into the finite element code MARC using the user subroutine HYPELA. Comparisons in terms of transverse deformation response, micro stress and strain distributions, and required CPU time are presented for GMC and finite element models of fiber/matrix unit cell. GMC is shown to provide comparable predictions of the composite behavior and requires significantly less CPU time as compared to a finite element analysis of the unit cell. Details as to the organization of the HYPELA code are provided with the actual HYPELA code included in the appendix.

Wilt, T. E.↗
NASA NTRS1982

Sensitivity analysis results of the effects of various parameters on composite design

Sensitivity analysis results are presented to assess the effects of a multitude of important parameters on fiber composite design and structural response. These results were obtained by using optimum design procedures in conjunction with sensitivity analyses. Sensitivity analyses were performed to assess the effects on composite optimum design and structural response of parameters such fiber transverse and shear properties, in situ matrix elastic and strength properties, correlation coefficients used in composite micromechanics and in combined strength predictions, processing variables, and perturbations of loading conditions. The results show that matrix properties, fiber volume ratio and small perturbations of the loading conditions have significant effects on certain composite structural responses. The remaining parameters have negligible effect.

Chamis, C. C.↗
NASA NTRS1981

Composite structural materials

Physical properties of fiber reinforced composites; structural concepts and analysis; manufacturing; reliability; and life prediction are subjects of research conducted to determine the long term integrity of composite aircraft structures under conditions pertinent to service use. Progress is reported in (1) characterizing homogeneity in composite materials; (2) developing methods for analyzing composite materials; (3) studying fatigue in composite materials; (4) determining the temperature and moisture effects on the mechanical properties of laminates; (5) numerically analyzing moisture effects; (6) numerically analyzing the micromechanics of composite fracture; (7) constructing the 727 elevator attachment rib; (8) developing the L-1011 engine drag strut (CAPCOMP 2 program); (9) analyzing mechanical joints in composites; (10) developing computer software; and (11) processing science and technology, with emphasis on the sailplane project.

Ansell, G. S.↗
DOE OSTI2026

Uniform Whole Wafer Anisotropic Etching of Structural Ta Thin Films

Tantalum (Ta) has promise as a structural material for micromechanical sensors and actuators. Anisotropic etching of alpha (α) phase Ta is required for micromachining applications. Uniform thickness and etch across a full wafer are desirable features. An experimental investigation is conducted to study plasma etching rate and anisotropy in etching α -Ta in relation to pressure and gas flow ratio. A comparatively low toxicity gas, carbon tetrafluoride (CF4), and argon (Ar) are used. Spectrometry by optical emission spectrometry (OES) and residual gas analysis (RGA) are employed to characterize the plasma to gain insight into the etch mechanisms. At low flow, the etch rate is slow due to an inadequate supply of the etching gas, CF4. The etch rate is also slowed at high flow due to a reduced CF4 residence time. Flow and pressure conditions to achieve a good etch rate and vertical sidewalls are identified and explained by means of a full factorial experiment coupled with emission spectra. Finally, with these conditions, uniform etching of 2.5 μm thick α-Ta across a 4-inch wafer is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The role of deviatoric stress and dislocations on the α to ω phase transformation in Ti

Under extreme conditions, α-Ti becomes unstable and transforms either into β-Ti at high temperature or into ω-Ti at high pressure. In what concerns the α to ω phase transformation (PT), there has been a wide range of experimentally reported transition pressures from approximately 2 to 15 GPa at room temperature. Deviatoric stresses and internal defects are often assumed to be the root cause of this variation. Here, in this study, these postulates are revisited using both continuum mechanics and molecular dynamics (MD) simulations. First, a simple continuum model, assuming linear elasticity and isotropic plasticity, is developed to describe the effects of applied stress and dislocations on the stability of an ω nucleus in an infinite α domain. Second, a new MD simulation method is developed to generate an ω nucleus in the α domain utilizing the displacement field identified from the topological analysis. Results from MD simulations show that despite the fact that phase diagrams typically delineate the limits between two phases in terms of only P and T, deviatoric stress promotes the α to ω phase transformation by reducing the critical radius above which an ω nucleus is stable. Furthermore, the required deviatoric stress to nucleate and stabilize a nanoscale ω nucleus is likely emanating from the internal stress of defects such as dislocations. The MD-informed micromechanics models are used to identify favorable configurations where dislocations help favor the α to ω transformation. These configurations show that the interaction with a basal or prismatic dislocation reduces the critical radius of a ω nucleus by about 10 or 16 %, respectively. In addition, prismatic edge dislocations are found to promote the growth of ω nucleus when interacting with the ($\bar{1}$$\bar{1}$20) α //(0001) ω interface. Importantly, a simple model of the arrival of dislocation at an ω nucleus suggests that PT does not necessarily require a pile-up to be present but could alternatively be mediated by a constant rapid flow of dislocations.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Finite element modeling of frictionally restrained composite interfaces

The use of special interface finite elements to model frictional restraint in composite interfaces is described. These elements simulate Coulomb friction at the interface, and are incorporated into a standard finite element analysis of a two-dimensional isolated fiber pullout test. Various interfacial characteristics, such as the distribution of stresses at the interface, the extent of slip and delamination, load diffusion from fiber to matrix, and the amount of fiber extraction or depression are studied for different friction coefficients. The results are compared to those obtained analytically using a singular integral equation approach, and those obtained by assuming a constant interface shear strength. The usefulness of these elements in micromechanical modeling of fiber-reinforced composite materials is highlighted.

Ballarini, Roberto↗
NASA NTRSDate not supplied

Lessons Learned and Best Practices for Utilizing a Generalized Composite Impact Model

A material model which incorporates several key capabilities which have been identified as lacking in currently available composite impact models has been developed. The material model utilizes experimentally based tabulated input to define the evolution of plasticity and damage as opposed to specifying discrete input parameters (such as modulus and strength). It has been implemented into the commercially available transient dynamic finite element code LS-DYNA® as MAT_213. The model can simulate the nonlinear deformation, damage and failure that take place in a composite under dynamic loading conditions. As MAT_213 is now being used by a general user community that did not participate in the model development process, a number of issues have been identified that caused uncertainty in assembling a MAT_213 input deck and conducting a MAT_213 analysis. The overall goal of this effort is to develop a quantified set of lessons learned and best practices which will permit a new user to conduct useful MAT_213 simulations without needing to have detailed expert knowledge of the material model and its theoretical underpinnings.

Micromechanics↗
NASA NTRS1988

A micromechanics model of the stiffness and strength of laminates with fiber waviness

A mathematical model based on the Euler-Bernoulli beam theory is proposed for predicting the effective Young's moduli of piecewise isotropic composite laminates with local ply curvatures in the main load-carrying layers. Strains in corrugated layers, In-Phase layers, Out-of-Phase layers are predicted for various geometries and material configurations by assuming matrix layers as elastic foundations of different spring constants. The effective Young's moduli measured from corrugated aluminum specimens and aluminum/epoxy specimens with In-Phase and Out-of-Phase wavy patterns coincide very well with the model predictions. Moire fringe analysis of an In-Phase specimen and an Out-of-Phase specimen are also presented confirming the main assumption of the model related to the elastic constraint due to the matrix layers. The present model is also compared with the experimental results and other models, including the micro-buckling models, published in the literature. The results of the present study show that even a very small scale local ply curvature produces a noticeable effect on the mechanical constitutive behavior of a laminated composite.

Harris, Charles E.↗