Search NASA⌕ Search

SEARCH · Search NASA

Results for “Concentration of measure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Experimental evaluation of respiratory droplet spread to rooms connected by a central ventilation system

This article presents results from an experimental study to ascertain the transmissibility of the SARS-CoV-2 virus between rooms in a building that are connected by a central ventilation system. Respiratory droplet surrogates made of mucus and virus mimics were released in one room in a test building and measurements of concentration levels were made in other rooms connected via the ventilation system. The paper presents experimental results for different ventilation system configurations, including ventilation rate, filtration level (up to MERV-13), and fractional outdoor air intake. The most important finding is that respiratory droplets can and do transit through central ventilation systems, suggesting a mechanism for viral transmission (and COVID-19 specifically) within the built environment in reasonable agreement with well-mixed models. We also find the deposition of these droplets on room walls to be negligibly small. Furthermore, the energy use impact of the different configuration settings is also quantified to help inform intelligent building operation that can simultaneously address energy use and occupant health.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2026

Investigation Into LiCl-LiF+Li 2 O as a Low Temperature Electrolyte in Direct Electrolytic Reduction of UO 2

Direct electrolytic reduction (DER) of UO 2 in a binary LiCl-Li2O (1–3 wt%) at 650 °C has been widely reported. The process temperature can be reduced to 550 °C in theory by using a near eutectic ternary LiCl-LiF+Li 2O (∼2 wt%) electrolyte, which will result in substantial reduction in rate of salt vaporization. The feasibility of using the ternary electrolyte for the process was tested via material compatibility testing, electrochemical polarization testing, and controlled potential or current DER experiments. MgO, Pt, and 625 nickel samples were each contacted with the ternary salt for 168 h. Negligible changes to dimensions and mass of the samples were measured, and concentrations of corrosion products in the salt were 102 ppm or less. O2−oxidation was observed to occur at a lower potential than Cl-or F-on a Pt anode. DER of UO2was performed in six trials. Process variables included type of reference electrode, electrochemical control method, type of cathode basket, and electrolyte composition. UO 2conversion ranged from 28.2 to 99.9 % , and current efficiency ranged from 38 to 52%. Overall, results indicate that the use of the ternary salt is feasible for DER.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Method for quantification of porcine type I interferon activity using luminescence, by direct and indirect means

Abstract Background Type I interferons are widely used in research applications and as biotherapeutics. Current assays used to measure interferon concentrations, such as plaque reduction assays and ELISA, are expensive, technically challenging, and may take days to provide results. We sought to develop a robust and rapid assay to determine interferon concentrations produced from transiently transfected cell cultures. Method Indirect quantification of recombinant interferon was evaluated using a novel bi-cistronic construct encoding the Foot-and-mouth disease virus 2A translational interrupter sequence to yield equimolar expression of Gaussia princeps luciferase and porcine interferon α. Direct quantification was evaluated by expression of a novel fusion protein comprised of Gaussia princeps luciferase and porcine type I interferon. Plasmids encoding constructs are transiently transfected into cell cultures and supernatant harvested for testing of luminescence, ELISA determined concentration, and anti-viral activity against vesicular stomatitis virus. Results Bi-cistronic constructs, utilized for indirect quantification, demonstrate both luciferase activity and anti-viral activity. Fusion proteins, utilized for direct quantification, retained secretion and luminescence however only the interferon α fusion protein had antiviral activity comparable to wildtype porcine interferon α. A strong linear correlation was observed between dilution and luminescence for all compounds over a dynamic range of concentrations. Conclusion The correlation of antiviral and luciferase activities demonstrated the utility of this approach, both direct and indirect, to rapidly determine recombinant interferon concentrations. Concentration can be determined over a more dynamic concentration range than available ELISA based assays using this methodology.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Optical, electrical, and EPR studies of polycrystalline Al:Cr:ZnSe gain elements

Transition metal-doped II-VI (TM:II-VI) chalcogenides are well-known laser materials for optically pumped middle-infrared lasers. Cr:ZnSe is a key representative of this class of transition metal doped II-VI gain media and is arguably considered the material of choice for optically pumped middle-infrared lasers. In addition to effective mid-IR lasing under optical excitation, these crystals, being wide-band semiconductors, hold the potential for direct electrical excitation. One way to form n-type conductivity in ZnSe crystals is by annealing them in a melt of Zn-Al alloy. However, this annealing of Cr:ZnSe crystals results in their purification and transfer of chromium to the melt of Zn-Al alloy. In this article, we report on optimizing the doping technique for providing n-type conductivity in Al:Cr:ZnSe crystals while preserving the chromium concentration. Al:Cr:ZnSe samples with resistivities ranging from 10.8 to 992 Ω-cm were fabricated. While the 2 + valence state of Cr is typically dominant in Cr:ZnSe, both Cr 2+ and Cr + were detected in Al:Cr:ZnSe samples. The maximum level of Cr + concentration was measured to be 4 × 10 18 cm -3 .

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effect of enrofloxacin on enteric Escherichia coli : Fitting a mathematical model to in vivo data

Antimicrobial drugs administered systemically may cause the emergence and dissemination of antimicrobial resistance among enteric bacteria. To develop logical, research-based recommendations for food animal veterinarians, we must understand how to maximize antimicrobial drug efficacy while minimizing risk of antimicrobial resistance. Our objective is to evaluate the effect of two approved dosing regimens of enrofloxacin (a single high dose or three low doses) on Escherichia coli in cattle. We look specifically at bacteria above and below the epidemiological cutoff (ECOFF), above which the bacteria are likely to have an acquired or mutational resistance to enrofloxacin. We developed a differential equation model for the antimicrobial drug concentrations in plasma and colon, and bacteria populations in the feces. The model was fit to animal data of drug concentrations in the plasma and colon obtained using ultrafiltration probes. Fecal E. coli counts and minimum inhibitory concentrations were measured for the week after receiving the antimicrobial drug. We predict that the antimicrobial susceptibility of the bacteria above the ECOFF pre-treatment strongly affects the composition of the bacteria following treatment. Faster removal of the antimicrobial drugs from the colon throughout the study leads to improved clearance of bacteria above the ECOFF in the low dose regimen. If we assume a fitness cost is associated with bacteria above the ECOFF, the increased fitness costs leads to reduction of bacteria above the ECOFF in the low dose study. These results suggest the initial E. coli susceptibility is a strong indicator of how steers respond to antimicrobial drug treatment.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Raw leaf gas exchange data, Leaf traits and 13CO2 experiment in the Amazon basin, Manaus, Brazil, 2019

This data package contains raw light response curves of mature leaves from 26 individuals, distributed among 18 species with different canopy positions, and leaf traits (LMA, N, P, and NSC) from Manaus-Brazil (June-November 2019). Branches were cut from the tree and re-cut under water. All measurements were made using (Li-6400XT, Li-Cor®, Lincoln, USA) under standard environmental conditions. Also, have data from an experiment with 13CO2 using a combined method with Licor 6400XT and Picarro. The experiment was conducted with one tropical species and measured the concentration of ¹³CO2 and ¹²CO2 to estimate rates of leaf respiration. All the files included in this data package are in .csv format with additional metadata spreadsheets in Excel file formats.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Cloud Particle Imager (CPI) and 3-View Cloud Particle Imager (3V-CPI) Instrument Handbook

The cloud particle imager (CPI) is a U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) user facility instrument for measuring the concentration and size of cloud droplet and ice crystals. Hydrometeors entering the tube will be detected by a system of two continuous wave lasers that are perpendicular to each other, monitoring the sample volume. When a hydrometeor obscures both laser beams it is inside the sample volume and a third laser is triggered to illuminate the hydrometeor and a camera records a two-dimensional image. The CPI records images with a resolution of 2.3 μm. Since the camera has 1024 x 1024 pixels, the maximum detectable size is 2.3 mm x 2.3 mm.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Calibration of Raman Spectrometer for Gas Phase Measurements

Raman spectroscopy is currently used at SRNL to measure the concentration of gaseous species evolved from chemical reactions. This report documents the methods used to calibrate the spectroscopic systems in both frequency and intensity spaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Additional Analysis of the 2H-Evaporator Wall Scale Sample HTF-17-57

Savannah River National Laboratory previously analyzed scale samples from both the wall and cone sections of the 242-16H Evaporator prior to chemical cleaning. The samples were analyzed for uranium and plutonium isotopes required for a Nuclear Criticality Safety Assessment of the scale removal process. The analysis of the scale samples found the material to contain crystalline nitrated cancrinite and clarkeite and significant amounts of mercury. Savannah River Remediation subsequently requested additional analyses on the samples. Inspection of the sample bottles revealed that no sample remained of the cone scale (HTF-17-56) while approximately 4 g of the wall scale sample (HTF-17-57) remained. The wall sample was subsequently ground with a mortar and pestle, at which time it was discovered that the sample contained a significant amount of liquid, metallic mercury. The portion of the sample that was not mercury was approximately 3 g. This portion of the sample was analyzed to determine the concentrations of selected radionuclides. The following radionuclide concentrations were measured: <9.6E+02 dpm/g H-3, 2.9E+02 dpm/g C-14, 5.6E+03 dpm/g Tc-99, and 1.6E+02 dpm/g I-129. Blank samples were also analyzed to evaluate sample contamination from the Shielded Cells environment. All blank sample results were below detectable limits. Due to the limited sample size and the anticipated low levels of the target radionuclides, no replicate sample analysis was conducted.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Results of the 2018 Wood Stove Design Challenge

The 2018 Wood Stove Design Challenge was an international design competition which sought to identify top performing residential wood stoves based on automation. To prepare for the event, the Northeast States for Coordinated Air Use Management (NESCAUM) developed a testing protocol that challenged the stoves by testing them in more field-like conditions—capturing emissions from start-up, reloading a stove, and the use of larger piece sizes. Flue gas emissions were measured using a combination of in-stack and novel dilution sampling methods, as the event occurred on the National Mall in Washington D.C. in a non-laboratory setting. Particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO2), and methane (CH4) were measured from three stoves in real-time. A combustion efficiency was also calculated for each stove in real-time. Measured PM emission rates ranged between 1.8 and 8.0 g/hr for all stoves and operating conditions, with the highest emissions being measured during cold start in all cases. The test average PM emission rates were 2.4, 4.0, and 2.4 g/hr for stoves A, B, and C, respectively. Results showed emissions measured during transient operations, which are often excluded in current certification methods, can be significantly higher than steady-state periods—echoing other studies and highlighting the importance of testing in various operational modes for more realistic emission estimates. Additionally, the stoves had overall CO emission rates of 48.8, 284.8, and 100.8 g/hr, for stoves A, B and C, respectively. Calculated PM and CO emission factors overall were low considering the testing protocol sought to follow more challenging yet realistic practices in terms of fuel loading and operating procedures. The overall estimated combustion efficiency for stoves A, B, and C was 85%, 78%, 76%, respectively and in all cases was lowest during the cold start period.This report details the successfully proposed and assembled instrumentation that was relatively portable for field-site testing and the results of the emissions measurements for the 2018 Wood Stove Design Challenge competition. Overall, the repeatability of each stove was favorable with coefficients of variation (COV) ranging from 7 to 15% for measured PM concentrations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Photo-cleaned Backgroundless Ion Chambers (Final Report for PDRD SR18010)

Ion chambers are often employed to measure the concentration of tritium within flowing gases. In real world environments the active surfaces of ion chambers become covered with tritiated surface contaminants. This tritiated surface contamination will create a large background response that can mask the signature of interest, which is the tritium concentration in the gas phase. Previous efforts to reduce the effects of surface contamination in ion chambers utilize inert coatings (e.g., gold) and low surface area electrodes (e.g., wire mesh), but this route only reduces the effect and does not necessarily alter the ratio of surface contamination to current collection area. Additionally, gold coating may add a substantial cost to the instrument. In the Tritium Facility, ion chambers are periodically cleaned using an alcohol-based process. This process is time consuming and often leads to ion chamber wear and breakage. In addition, periodic cleaning does not address tritium level ambiguities in gloveboxes. An ideal solution to this issue would be to either develop an ion chamber that does not accrue surface contamination, or one that is self-cleaning while it is in operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Rogers Quarry Special Studies Report 2023

Rogers Quarry (RQ) has a history of elevated Se concentrations in water and fish caused by inputs from the Y-12 National Security Complex Filled Coal Ash Pond (FCAP). Selenium is acutely toxic at high concentrations, and chronic toxicity occurs at low aqueous concentrations because Se bioaccumulates in fish tissues. The US Environmental Protection Agency (EPA) recently developed water quality criteria for Se that include fish tissue as well as aqueous Se concentrations. The water column concentration criterion is 1.5 µg L -1 for lentic ecosystems and 3.1 µg L -1 for lotic ecosystems. The fish tissue criteria include both an egg/ovary concentration (15.1 μg/g dry weight) and a concentration for whole-body (8.5 μg/g dry weight) or fish muscle (11.3 μg/g dry weight). The egg/ovary criterion supersedes the fillet and aqueous concentrations if measured because Se toxicity manifests via reproductive effects in birds and fish. It is maternally transferred through eggs, leading to teratogenicity (i.e., deformities, developmental effects) in young fish.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Analysis of Defense Waste Processing Facility (DWPF) Condensate Samples and Evaluation of the Glycolate Destruction Process during Nitric-Glycolic flowsheet Transition

Glycolate concentrations were measured by the Savannah River National Laboratory (SRNL) in Slurry Mix Evaporator Condensate Tank (SMECT) and Recycle Collection Tank (RCT) samples retrieved after implementation of the Nitric-Glycolic Acid flowsheet at the Defense Waste Processing Facility (DWPF). No glycolate has been detected in any sample using Ion Chromatography (IC) with a detection limit of 8 mg/L, and no glycolate has been detected using either IC or Proton Nuclear Magnetic Resonance Spectroscopy ( 1 HNMR) after a permanganate strike was performed in the RCT.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Advanced Monitoring and Control in the ANL METL Facility Using an Engineering Digital Twin

The potential benefits of using an engineering digital twin to achieve greater autonomy for monitoring and control functions in advanced reactors was investigated for the Mechanisms Engineering Test Loop (METL) liquid sodium facility at Argonne National Laboratory. The METL sodium purification system served as a representative system as it requires significant human in-the-loop interaction to accomplish its design function. The objective was to demonstrate how real-time operation could be automated while preserving oversight of the operator for ensuring that the system design functions are met. A digital twin model of the purification system was developed for both the cold trap purification loop and plugging meter diagnostic loop using information from the METL piping and instrumentation diagram (P&ID). Automated monitoring and diagnosis of component degradation in the METL facility was demonstrated in tests using the PRO-AID health monitoring software with the digital twin model incorporated in the library of components. Component failures were introduced and were successfully diagnosed in real time. These tests serve to demonstrate an advanced monitoring capability able to differentiate sensor degradation from component degradation, to generate a rank ordering of probabilities of different failure mechanisms that serves to circumvent the false alarm problem with current anomaly detection methods, and how facility monitoring can be transformed from anomaly detection to identification of a specific fault. Automated control of the purification system was demonstrated through simulations that exercised a model predictive controller designed using the digital twin model. Results of these simulations compared favorably with experimental data showing very good reference tracking response with negligible overshoot. In conclusion, these pilot tests and simulations successfully demonstrated the use of a digital twin for improved automation of monitoring and control. It was shown how the digital twin enables switching between control modes from cold trap operation where impurities are removed to plugging meter operation where impurity concentrations are measured.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Application of Partial Least Squares Approaches to Pyroprocessing ER Data

Multivariate approaches show promise for application to process monitoring for safeguards of pyroprocessing. Past MPACT work explored the application of Principal Component Analysis (PCA) to detect off-normal conditions in pyroprocessing electrorefiner (ER) data from in the Hot Fuel Examination Facility (HFEF) at Idaho National Laboratory (INL) known as the Scalable Pyrochemical Recycling testbed (SPyRe) ER. PCA, however, does not consider the output variables. In FY24, multivariate analysis was extended from PCA to Partial Least Squares (PLS) analysis. PLS maximizes the variance between both the input signals and output variables. In the case of this work, PLS was applied in two different manners: Predictive PLS and Discriminant PLS. Predictive PLS maximizes the covariance between the process variables of the ER and the measured U concentration from in-situ voltammetry. Discriminant PLS maximizes the covariance between the process variables and a set of training process “states” such as known off-normal conditions. By projecting into the latent variable space in PLS, the process variables can be regressed onto the outputs and predictions can be made for new data sets. In this work, by applying predictive PLS, a penalized non-linear PLS approach was able to make predictions of concentration based on test and training data and detect when operations were off-normal. However, the predictive PLS does not classify the signals to which off-normal operations are attributable. Discriminant PLS can be used to classify off-normal operations but is inadequate to properly classify specific off-normal classes like power supply faults when the Discriminant PLS model is only specifically trained to detect that off-normal class. When all faults are trained against the observation data, all three operational classes are accurately classified and distinguished. Thus, future application of latent variable techniques should not select any given method, but should use a mixture of PCA, Predictive PLS, and Discriminant PLS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Laser-heated Pedestal Growth and Raman DTS for Harsh-environment Applications

Fibers composed of single crystal (SC) materials are mechanically, thermally, and chemically robust to harsh conditions, and thus attractive for sensing applications in harsh environments. However, SC fibers grown via the laser-heated pedestal growth (LHPG) technique do not intrinsically have a functional cladding layer. We investigate self-segregation of dopants in a crystal matrix within a SC fiber. Ti and Cr dopants within a sapphire matrix were grown via the LHPG method. Cross-sectional dopant concentrations were measured via electron-probe micro-analysis (EPMA). The cross-sectional constituent profiles and resulting transmissivities were characterized as a function of growth parameters.

Lander, Gary↗
DOE OSTI2022

Characterization and application of a high-resolution microfluidic device in atmospheric ice nucleation research and integrated science teaching

Ambient ice-nucleating particles (INPs) represent an important subset of aerosol particles that facilitate heterogeneous formation of ice crystals in the atmosphere, which can impact Earth system and energy. In this work, we developed an affordable high-resolution platform to replicate atmospheric immersion freezing through the unique capabilities of microfluidics to measure INP concentration of known ice nucleation active materials, as well as high-latitude soil samples. The new instrument produced comparable and extended freezing efficiency data for a multitude of samples over the temperature range of -5 to -35 °C as compared to an existing freezing assay within known uncertainties. Moreover, the new assay was integrated into science teaching at a primarily undergraduate and Hispanic-serving institute, contributing to fostering a deeper understanding of ice nucleation processes among college students, instilling their enthusiasm for science, and addressing the critical need for a well-informed citizenry. Student research assistants were involved in both research and pedagogical development processes. Three students from our team visited the Pacific Northwest National Laboratory to help characterize physicochemical properties of our test samples and to test modeling of atmospheric ice nucleation using a box model as well as a global climate model (E3SM) for the regional-scale conditions over the North Slope of Alaska (NSA) and Southern Great Plains (SGP). We also assessed student learning experience via hands-on training, research processes, and development of educational materials. On pre- and post-participation surveys and in exit interviews, students reported personal growth as advancements in breadth of experience, research-related skill sets, and regarding their educational and career goals. They also affirmed that the methods enacted incorporated the NASA Minority University Research and Education Program (MUREP) STEM Engagement Best Practices.

58 GEOSCIENCES↗