Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain boundary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Development of an extra-high strength powder metallurgy nickel-base superalloy

A program was conducted to optimize the composition of NASA IIb-11, an alloy originally developed as a wrought material, for thermal stability and to determine the feasibility for producing the alloy using powder metallurgy techniques. Seven compositions were melted and atomized, hot isostatically pressed, cross rolled to disks and heat treated. Tensile and stress rupture properties from room temperature to 870 C (1600 F) were determined in addition to thermal stability characteristics. Processing variables included hot isostatic pressing parameters and handling, cross rolling procedures and heat treatment cycles. NASA IIb-11E displayed the best combination of overall properties for service as a 760 C (1400 F) disk material. Its composition is 0.06 C, 8.5 Cr, 9.0 Co, 2.0 Mo, 7.1 W, 6.6 Ta, 4.5 Al, 0.75 Ti, 0.5 V, 0.7 Hf, 0.01 B, 0.05 Zr and balance Ni. While the alloy exhibits the highest 760 C (1400 F) rupture strength reported for any powder metallurgy disk alloy to date, additional studies to further evaluate the effects of heat treatment may be required. The alloy is not susceptible to topologically close-packed phase formation during thermal exposure at 870 C (1600 F) for 1,500 hours, but its mechanical property levels are lowered due to grain boundary carbide formation.

Kent, W. B.↗
NASA NTRS1977

Carburization and heat treatment to cause carbide precipitation in gamma/gamma prime-delta eutectic alloys

In an attempt to improve their longitudinal shear strength, several directionally solidified eutectic alloy compositions with minor element modifications were pact, carburized, and heat treated to provide selective carbide precipitation at the cell and grain boundaries. The directionally solidified Ni-17.8 Nb-6Cr-2.5Al-3Ta (weight percent) alloy was selected for the shear strength evaluation because it showed the shallowest delta-denuded zone at the carburized surface. The carburization-carbide precipitation treatment, however, did not appear to improve the longitudinal shear strength of the alloy.

Tewari, S. N.↗
NASA NTRS1977

Effects of alloy composition in alleviating embrittlement problems associated with the tantalum alloy T-111

The causes of aging embrittlement in T-111 (Ta-8W-2Hf) and the effects of alloy modification were investigated. Results showed that T-111 contains a critical combination of tungsten and hafnium that leads to loss of ductility at -196 C after aging near 1040 C. This appears to occur because tungsten enhances hafnium segregation to grain boundaries and this also leads to increased susceptibility to hydrogen embrittlement. Aging embrittlement was not observed in tantalum alloys with reduced tungsten or hafnium contents; however, most of the alloys studied have lower strengths than T-111 and exhibit susceptibility to hydrogen embrittlement.

Stephens, J. R.↗
NASA NTRS1977

Effects of long-term aging on ductility and microstructure of Cb and Mo alloys

A program was conducted to determine if aging embrittlement occurs in columbium-base alloys C-103, Cb-1Zr, and Cb-752 or in a molybdenum alloy, Mo-TZM. Results showed that aging embrittlement does not occur in C-103, Cb-1Zr, or Mo-TZM during long-term (1000 hour) aging at temperatures in the range of 700-1025 C. In comparison, aging embrittlement occurred in the Cb-752 alloy after similar aging at 900 C. A critical combination of the solute additions W and Zr led to Zr segregation at grain boundaries during long-term aging which subsequently resulted in embrittlement as indicated by an increase in the ductile-brittle transition temperature from below -196 C to about -150 C.

Stephens, J. R.↗
NASA NTRS1977

Transmutation doping of silicon solar cells

Normal isotopic silicon contains 3.05% of Si-30 which transmutes to P-31 after thermal neutron absorption, with a half-life of 2.6 hours. This reaction is used to introduce extremely uniform concentrations of phosphorus into silicon, thus eliminating the areal and spatial inhomogeneities characteristic of chemical doping. Annealing of the lattice damage in the irradiated silicon does not alter the uniformity of dopant distribution. Transmutation doping also makes it possible to introduce phosphorus into polycrystalline silicon without segregation of the dopant at the grain boundaries. The use of neutron transmutation doped (NTD) silicon in solar cell research and development is discussed.

Wood, R. F.↗
NASA NTRS1978

Interdisciplinary research and development on the effects of the nature and properties of ceramic materials in the design of advanced structural components

An educational development and supportive research program on ceramic materials established to advance design methodology, improve materials, and develop engineers knowledgable in design with and use of high performance ceramic materials is described. Emphasis is on the structures and related materials problems in a ceramic turbine engine, but applications in coal gasification, solar conversion, and magnetohydrodynamic technologies are considered. Progress of various research projects in the areas of new materials, processing, characterization, and nondestructive testing is reported. Fracture toughness determination, extended X-ray absorption fine structure measurements, and grain boundary effects in beta-alumina are among the topics covered.

Source record↗
NASA NTRS1978

Wear of single-crystal silicon carbide in contact with various metals in vacuum

Sliding friction experiments were conducted in vacuum with single crystal silicon carbide (0001) surface in contact with transition metals (tungsten, iron, rhodium, nickel, titanium, and cobalt), copper, and aluminum. The hexagon shaped cracking and fracturing of silicon carbide that occurred is believed to be due to cleavages of both the prismatic and basal planes. The silicon carbide wear debris, which was produced by brittle fracture, slides or rolls on both the metal and silicon carbide and produces grooves and indentations on these surfaces. The wear scars of aluminum and titanium, which have much stronger chemical affinity for silicon and carbon, are generally rougher than those of the other metals. Fracturing and cracking along the grain boundary of rhodium and tungsten were observed. These may be primarily due to the greater shear moduli of the metals.

Miyoshi, K.↗
NASA NTRS1977

Pressureless sintered beta prime-Si3N4 solid solution: Fabrication, microstructure, and strength

Si3N4, AlN, and Al2O3 were used as basic constituents in a study of the pressureless sintering of beta prime-Si3N4 solid solution as a function of temperature. Y2O3-SiO2 additions were used to promote liquid-phase sintering. The sintered specimens were characterized with respect to density, microstructure, strength, oxidation, and thermal shock resistance. Density greater than 98 percent of theoretical was achieved by pressureless sintering at 1750 C. The microstructure consisted essentially of fine-grained beta prime-Si3N4 solid solution as the major phase. Modulus of rupture strengths up to 483 MPa were achieved at moderate temperature (1000 C), but decreased to 228 MPa at 1380 C. This substantial strength loss was attributed to a glassy grain boundary phase formed during cooling from the sintering temperature. The best oxidation resistance was exhibited by a composition containing 3 mol % Y2O3-SiO2 additives. Water quench thermal shock resistance was equivalent to that of reaction sintered silicon nitride but lower than hot-pressed silicon nitride.

Dutta, S.↗
NASA NTRS1978

A study of the mechanisms of hydrogen embrittlement in molybdenum

The mechanical properties of polycrystalline molybdenum samples in both the 'as annealed' and hydrogenized conditions were studied. The results indicate that hydrogen does not alter the yield stress of samples significantly although it reduces both the ultimate tensile strength and the ductility considerably. Fractographic study of samples shows a tendency to intercrystalline cracking of the hydrogenised molybdenum at low temperatures. In the light of the results, a mechanism involving grain boundary weakening is suggested.

Taheri, M.↗
NASA NTRS1978

High temperature compressive cracking in hot-pressed silicon nitride

Results are presented for high-temperature (1370, 1430, 1540, 1590 C) slow-strain-rate compression tests on cylindrical specimens of hot-pressed Si3N4 of the HS-130 brand under various compressive loads. The results are presented in terms of number of longitudinal cracks, percent increase in diameter, percent decrease in length, and percent loss in weight. Scanning electron micrographs are presented of cylindrical surfaces of compression specimens tested at 1430 C for 640 MN/sq m and at 1590 C for 220 MN/sq m. As compared to results obtained by other investigators, it appears more likely that the cracks resulting from compressive loading are due to subcritical crack growth caused by circumferential tensile stresses acting across grain boundaries that contain a viscous silicate glass phase.

Sanders, W. A.↗
NASA NTRS1977

Pressureless sintered beta-prime-Si3N4 solid solution - Fabrication, microstructure, and strength

Pressureless sintering of beta-prime-Si3N4 solid solution was studied as a function of temperature using Si3N4, A1N, and Al2O3 as basic constituents. Y2O3-SiO2 additions were used to promote liquid-phase sintering. The sintered specimens were characterized with respect to density, microstructure, strength, oxidation, and thermal shock resistance. Density greater than 98 percent of theoretical was achieved by pressureless sintering at 1750 C. The microstructure consisted essentially of fine-grained beta-prime-Si3N4 solid solution as the major phase. Modulus of rupture strengths up to 483 M Pa were achieved at moderate temperature (1000 C), but decreased to 228 M Pa at 1380 C. This substantial strength loss was attributed to a 'glassy' grain boundary phase formed during cooling from the sintering temperature. The best oxidation resistance was exhibited by a composition containing 3 mol % Y2O3-SiO2 additives. Water quench thermal shock resistance was equivalent to that of reaction sintered silicon nitride but lower than hot-pressed silicon nitride.

Dutta, S.↗
NASA NTRS1978

A Schottky-barrier solar cell on sliced polycrystalline GaAs

Antireflecting-metal-oxide-semiconductor (AMOS) technology has been applied to sliced wafers of polycrystalline GaAs having grain sizes of about 100 microns. Simulated AM1 sunlight efficiencies up to 14% were obtained, and studies using the scanning electron microscope showed that grain boundaries have a minimal effect on short-circuit current density. However, current-voltage characteristics show some influence on open-circuit voltage.

Yeh, Y. C. M.↗
NASA NTRS1978

Silicon solar cell process. Development, fabrication and analysis

Solar cells were fabricated from unconventional silicon sheets, and the performances were characterized with an emphasis on statistical evaluation. A number of solar cell fabrication processes were used and conversion efficiency was measured under AMO condition at 25 C. Silso solar cells using standard processing showed an average efficiency of about 9.6%. Solar cells with back surface field process showed about the same efficiency as the cells from standard process. Solar cells from grain boundary passivation process did not show any improvements in solar cell performance.

Yoo, H. I.↗
NASA NTRS1979

Effect of grain orientation and coating on thermal fatigue resistance of a directionally solidified superalloy (MAR-M 247)

The effect of off-axis directionally solidified (DS) grain growth on thermal fatigue life of Mar-M 247 alloy was evaluated. Uncoated conventionally cast as well as DS wedge bars were cycled in a burner rig between 1070 C and room temperature. The longitudinal axis and leading edge of the specimen coincided. As the angle between the specimen longitudinal axis and growth axis increased, the thermal fatigue life decreased for both the uncoated and aluminide-coated bars. Life increases of about 50 cycles for the DS conditions were attributed to coating. The decrease in thermal fatigue life with increasing angle is primarily attributed to the increase in modulus of elasticity with increasing angle and not to the intersection of DS grain boundaries with the specimen leading edge. The thermal fatigue cracks were observed to be transgranular in the DS material. Limited tensile and stress-rupture properties of conventionally cast and off-axis DS Mar-M 247 alloy are also presented.

Bizon, P. T.↗
NASA NTRS1979

Silicon solar cell fabrication technology

The laser cell scanner was used to characterize a number of solar cells made in various materials. An electron beam-induced current (EBIC) study was performed using a stereoscan scanning electron microscope. Planar p-n junctions were analyzed. A theory for the EBIC based on the analytical solution of the ambipolar diffusion equation under the influence of electron beam excitation parameter z (which is related to beam penetration), the junction depth Z sub j, the beam current and the surface recombination, was formulated and tested. The effect of a grain boundary was studied.

Stafsudd, O. M.↗
NASA NTRS1979

Quantitative Analysis of Defects in Silicon

The evaluation and prediction of the conversion efficiency for a variety of silicon samples with differences in structural defects, such as grain boundaries, twin boundaries, precipitate particles, dislocations, etc. are discussed. Quantitative characterization of these structural defects, which were revealed by etching the surface of silicon samples, is performed by using an image analyzer. Due to different crystal growth and fabrication techniques the various types of silicon contain a variety of trace impurity elements and structural defects. The two most important criteria in evaluating the various silicon types for solar cell applications are cost and conversion efficiency.

Natesh, R.↗