Search NASA⌕ Search

SEARCH · Search NASA

Results for “current density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Fully Printed High-Frequency Phased-Array Antenna on Flexible Substrate

To address the issues of flexible electronics needed for surface-to-surface, surface-to-orbit, and back-to-Earth communications necessary for manned exploration of the Moon, Mars, and beyond, a room-temperature printing process has been developed to create active, phased-array antennas (PAAs) on a flexible Kapton substrate. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proven feasible for phased-array antenna systems. The carrier mobility of an individual CNT is estimated to be at least 100,000 sq cm/V(dot)s. The CNT network in solution has carrier mobility as high as 46,770 sq cm/V(dot)s, and has a large current-density carrying capacity of approx. 1,000 mA/sq cm , which corresponds to a high carrying power of over 2,000 mW/ sq cm. Such high carrier mobility, and large current carrying capacity, allows the achievement of high-speed (>100 GHz), high-power, flexible electronic circuits that can be monolithically integrated on NASA s active phasedarray antennas for various applications, such as pressurized rovers, pressurized habitats, and spacesuits, as well as for locating beacon towers for lunar surface navigation, which will likely be performed at S-band and attached to a mobile astronaut. A fully printed 2-bit 2-element phasedarray antenna (PAA) working at 5.6 GHz, incorporating the CNT FETs as phase shifters, is demonstrated. The PAA is printed out at room temperature on 100-mm thick Kapton substrate. Four CNT FETs are printed together with microstrip time delay lines to function as a 2-bit phase shifter. The FET switch exhibits a switching speed of 0.2 ns, and works well for a 5.6-GHz RF signal. The operating frequency is measured to be 5.6 GHz, versus the state-of-the-art flexible FET operating frequency of 52 MHz. The source-drain current density is measured to be over 1,000 mA/sq cm, while the conventional organic FETs, and single carbon nanotube-based FETs, are typically in the mA to mA/sq cm range. The switching voltage used is 1.8 V, while the state-of-the-art flexible FET has a gate voltage around 50 V. The gate voltage can effectively control the source-drain current with an ON-OFF ratio of over 1,000 obtained at a low Vds bias of 1.8 V. The azimuth steering angles of PAA are measured at 0deg, -14.5deg, -30deg, and 48.6deg. The measured far-field patterns agree well with simulation results. The efficiency of the 2-bit 2-element PAA is measured to be 39 percent, including the loss of transmission line, FET switch, and coupling loss of RF probes. With further optimization, the efficiency is expected to be around 50-60 percent.

Chen, Yihong↗
DOE OSTI2024

Pathway to High Rate Capability in Interconnected Composite Electrolytes: A Case Study with a Single-Ion-Conducting Polymer

In a three-dimensional interconnected polymer/ceramic composite electrolyte (3D composite), both the polymer and ceramic electrolyte phases are individually connected with a polymer-rich surface layer to provide conformal contact with the electrodes. This work investigates how the transference number of the polymer phase affects the electrochemical properties of the 3D composite. Here, we fabricate a 3D composite using a “single-ion” conducting polymer electrolyte (PE), Li 1+x+y Al x Ti 2–x Si y P 3–y O 12 (LICGC) ceramic, and compare its electrochemical properties with the neat polymer, and with a 3D composite made with a dual-ion-conducting PE (we reported previously). Our results reveal that changing the polymer phase from a dual-ion-conducting PE to a single-ion-conducting PE results in a 9-fold increase in the limiting current density, although the interfacial impedance between the polymer and LICGC ceramic remains high (and contributes significantly to the total impedance of the 3D composite). Further, the limiting current density of the 3D composite is dictated by the PE and minimally affected by the ceramic scaffold. The ceramic scaffold, however, helps to ease the concentration gradient buildup within the PE and moderately improves the overall transference number. The LICGC scaffold does not provide any additional Li dendrite resistance due to its high reactivity with Li.

25 ENERGY STORAGE↗
NASA NTRS1986

Modeling for CO poisoning of a fuel cell anode

Poisoning losses in a half-cell in the 110-190 C temperature range have been measured in 100 wt pct H3PO4 for various mixtures of H2, CO, and CO2 gases in order to investigate the polarization loss due to poisoning by CO of a porous fuel cell Pt anode. At a fixed current density, the poisoning loss was found to vary linearly with ln of the CO/H2 concentration ratio, although deviations from linearity were noted at lower temperatures and higher current densities for high CO/H2 concentration ratios. The surface coverages of CO were also found to vary linearly with ln of the CO/H2 concentration ratio. A general adsorption relationship is derived. Standard free energies for CO adsorption were found to vary from -14.5 to -12.1 kcal/mol in the 130-190 C temperature range. The standard entropy for CO adsorption was found to be -39 cal/mol per deg K.

Dhar, H. P.↗
NASA NTRS1995

Growth and Analysis of Highly Oriented (11n) BCSCO Films for Device Research

Films of BCSCO superconductor of the type Bi2CaSr2Cu2O(x), have been grown by liquid phase epitaxy method (LPE), using a partially closed growth chamber. The films were grown on (001) and (110) NdGaO3 substrates by slow cooling process in an optimized temperature range below the peritectic melting point (880 C) of Bi2CaSr2Cu2O8. Optimization of parameters, such as seed rotation, soak of initial growth temperature and growth period results in the formation of 2122 phase BCSCO films. The films grown at rotation rates of less than 30 and more than 70 rpm are observed to be associated with the second phase of Sr-Ca-Cu-O system. Higher growth temperatures (greater than 860 C) also encourage to the formation of this phase. XRD measurements show that the films grown on (110) NdGaO3 have a preferred (11n)-orientation. It is pertinent to mention here that in our earlier results published elsewhere we obtained c-axis oriented Bi2CaSr2Cu2O8 phase films on (001) NdGaO3 substrate. Critical current density is found to be higher for the films grown on (110) than (001) NdGaO3 substrate orientation. The best values, zero resistance (T(sab co)) and critical current density obtained are 87 K and 10(exp 5) A/sq cm respectively.

Raina, K. K.↗
DOE OSTI2024

Theoretical Assessment of the Transition Between Electron Emission Mechanisms for Nonplanar Diodes

Theoretically and computationally describing the operation of nanodiodes requires characterizing the transitions between multiple electron emission mechanisms for nanodiodes with complicated geometries. This motivates our development of techniques to determine when simplified theories for individual mechanisms suffice compared to more complete, but more computationally expensive, models. Leveraging recent theories that define a canonical gap distance to translate planar theory to nonplanar diodes, we derive the conditions for the transitions among thermal emission, field emission, and space-charge-limited current density (SCLCD) in vacuum and with collisions for non-Cartesian coordinate systems, including spherical, cylindrical, and prolate spheroidal coordinate systems. Particle-in-cell (PIC) simulations of the current density as a function of applied voltage for a tip-to-plate geometry in vacuum agreed qualitatively with the asymptotes for thermal emission at low voltage and SCLCD at higher voltage using the canonical gap distance. As a result, this demonstrates the utility of this approach for guiding system design and suggests future extensions to save simulation time for more realistic geometries that are more computationally expensive.

Conformal mapping↗
DOE OSTI2024

Cobalt‐Doped Bismuth Nanosheet Catalyst for Enhanced Electrochemical CO 2 Reduction to Electrolyte‐Free Formic Acid

Electrochemical carbon dioxide (CO 2 ) reduction reaction (CO 2 RR) to valuable liquid fuels, such as formic acid/formate (HCOOH/HCOO − ) is a promising strategy for carbon neutrality. Enhancing CO 2 RR activity while retaining high selectivity is critical for commercialization. To address this, we developed metal-doped bismuth (Bi) nanosheets via a facile hydrolysis method. These doped nanosheets efficiently generated high-purity HCOOH using a porous solid electrolyte (PSE) layer. Among the evaluated metal-doped Bi catalysts, Co-doped Bi demonstrated improved CO 2 RR performance compared to pristine Bi, achieving ~90 % HCOO − selectivity and boosted activity with a low overpotential of ~1.0 V at a current density of 200 mA cm −2 . In a solid electrolyte reactor, Co-doped Bi maintained HCOOH Faradaic efficiency of ~72 % after a 100-hour operation under a current density of 100 mA cm −2 , generating 0.1 M HCOOH at 3.2 V. Density functional theory (DFT) results revealed that Co-doped Bi required a lower applied potential for HCOOH generation from CO 2 , due to stronger binding energy to the key intermediates OCHO* compared to pure Bi. In conclusion, this study shows that metal doping in Bi nanosheets modifies the chemical composition, element distribution, and morphology, improving CO 2 RR catalytic activity performance by tuning surface adsorption affinity and reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1982

Ion extraction capabilities of closely spaced grids

The ion extraction capabilities of accelerator systems with small screen hole diameters (less than 2.0 mm) are investigated at net-accelerating voltages of 100, 300, and 500 V. Results show that the impingement-limited perveance is not dramatically affected by reductions in screen hole diameter to 1.0 mm, but impingement-limited performance was found to be dependent on the grid separation distance, the discharge-to-total accelerating voltage ratio, and the net-to-total accelerating voltage ratio. Results obtained using small hole diameters and closely spaced grids indicate a new mode of grid operation where high current density operation can be achieved with a specified net acceleration voltage by operating the grids at a high rather than low net-to-total acceleration voltage. Beam current densities as high as 25 mA/sq cm were obtained using grids with 1.0 mm diameter holes operating at a net accelerating voltage of 500 V.

Rovang, D. C.↗
NASA NTRS1987

Spacecraft dielectric surface charging property determination

The charging properties of 127 micron thick polyimide, (a commonly used spacecraft dielectric material) was measured under conditions of irradiation by a low-current-density electron beam with energy between 2 and 14 keV. The observed charging characteristics were consistent with predictions of the NASCAP computer model. The use of low electron current density results in a nonlinearity in the sample-potential versus beam-energy characteristic which is attributed to conduction leakage through the sample. Microdischarges were present at relatively low beam energies.

Williamson, W. S.↗
NASA NTRS1990

Electrochemical incineration of wastes

The novel technology of waste removal in space vehicles by electrochemical methods is presented to convert wastes into chemicals that can be eventually recycled. The important consideration for waste oxidation is to select a right kind of electrode (anode) material that should be stable under anodic conditions and also a poor electrocatalyst for oxygen and chlorine evolution. On the basis of long term electrolysis experiments on seven different electrodes and on the basis of total organic carbon reduced, two best electrodes were identified. The effect of redox ions on the electrolyte was studied. Though most of the experiments were done in mixtures of urine and waste, the experiments with redox couples involved 2.5 M sulfuric acid in order to avoid the precipitation of redox ions by urea. Two methods for long term electrolysis of waste were investigated: (1) the oxidation on Pt and lead dioxide electrodes using the galvanostatic methods; and (2) potentiostatic method on other electrodes. The advantage of the first method is the faster rate of oxidation. The chlorine evolution in the second method is ten times less then in the first. The accomplished research has shown that urine/feces mixtures can be oxidized to carbon dioxide and water, but current densities are low and must be improved. The perovskite and Ti4O7 coated with RuO2 are the best electrode materials found. Recent experiment with the redox agent improves the current density, however, sulphuric acid is required to keep the redox agent in solution to enhance oxidation effectively. It is desirable to reduce the use of acid and/or find substitutes.

Bhardwaj, R. C.↗
NASA NTRS1995

Growth and analysis of highly oriented (11n) BCSCO films for device research

Films of BCSCO superconductor of the type Bi2CaSr2Cu2Ox have been grown by liquid phase epitaxy method (LPE), using a partially closed growth chamber. The films were grown on (001) and (110) NdGaO3 substrates by slow cooling process in an optimized temperature range below the peritectic melting point (880 C) of Bi2CaSr2Cu2O8. Optimization of parameters, such as seed rotation, soak of initial growth temperature and growth period results in the formation of 2122 phase BCSCO films. The films grown at rotation rates of less than 30 and more than 70 rpm are observed to be associated with the second phase of Sr-Ca-Cu-O system. Higher growth temperatures (is greater than 860 C) also encourage to the formation of this phase. X-Ray Diffraction (XRD) measurements show that the films grown on (110) NdGaO3 have a preferred (11 n)-orientation. It is pertinent to mention here that in our earlier results published elsewhere we obtained c-axis oriented Bi2CaSr2Cu2O8 phase films on (001) NdGaO3 substrate. Critical current density is found to be higher for the films grown on (110) than (001) NdGaO3 substrate orientation. The best values of zero resistance (T(sub co)) and critical current density obtained are 87 K and 105 A/sq cm, respectively.

Raina, K. K.↗
NASA NTRS2021

Effect of Reactant Purity on Proton Exchange Membrane Fuel Cell Performance

NASA has set a goal to return to the Moon and to establish a sustained lunar presence. Many applicable lander and upperstage vehicle concepts utilize cryogenic H2 and O2 propellants. This propellant selection enables appealing potential mission concepts wherein electricity is generated by operating a fuel cell on residual H2 and O2 propellants. This concept depends on the capability of the fuel cell to utilize dry, propellant-grade reactants with concentrations of up to 30 percent He present. This study consists of the evaluation of a 12-cell non-flow-through proton exchange membrane fuel cell stack of 50 sq. cm active area with passive water removal. This stack was supplied with three levels of reactant purity: >99.999, 99.1, and 70 mol%, with the remainder made up of He. The reactant humidity and flow-through rate were also assessed as performance factors, and the fuel stack repeatedly supported a load profile with current densities up to 500 mA/sq. cm (25 A). The fuel cell performed consistently over the course of testing, with cell voltages decreasing approximately 50 mV at the maximum current density when supplied with reactants with 30 percent He present.

electrochemistry↗
DOE OSTI2025

The Physics of Micro-Pinches

This project focused on using pulsed-power-driven techniques to study the coupling of high-energy-density (HED) magnetic fields to HED matter in the laboratory. Specifically, we studied a phenomenon known as "micro-pinching" to obtain HED conditions on a modest, university-scale pulsed-power driver: the 1-MA, 100-ns MAIZE linear transformer driver (LTD) facility at the University of Michigan. We used the "X-pinch" platform as a means of generating micro-pinch HED plasmas. An X-pinch is formed when two or more wires are crossed into the shape of an 'X' and a large electrical current is driven through the wires. This creates an intense electrical current density at the crossing point of the wires. Associated with this current density is an intense magnetic field and an intense magnetic field pressure. The magnetic field pressure compresses and heats the wire material into the HEDP regime. The use of an X-pinch platform ensures that the micro-pinch HED plasma will form in a well-controlled location, which helps with diagnostics alignment. This platform allowed us to explore the extreme plasma conditions and magnetic field pressures that can be generated with compact pulsed-power technology and intensely focused discharge currents. Understanding the limits of intensely focused discharge currents could have an enormous impact on HED science, especially when one considers the scaling of these platforms to the 30-MA Z facility at Sandia National Laboratories, where pressures well in excess of 1 Gbar could be achieved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Amino Acid Sequence Controls Enhanced Electron Transport in Heme-Binding Peptide Monolayers

Metal-binding proteins have the exceptional ability to facilitate long-range electron transport in nature. Despite recent progress, the sequence-structure–function relationships governing electron transport in heme-binding peptides and protein assemblies are not yet fully understood. In this work, the electronic properties of a series of heme-binding peptides inspired by cytochrome bc1 are studied using a combination of molecular electronics experiments, molecular modeling, and simulation. Self-assembled monolayers (SAMs) are prepared using sequence-defined heme-binding peptides capable of forming helical secondary structures. Following monolayer formation, the structural properties and chemical composition of assembled peptides are determined using atomic force microscopy and X-ray photoelectron spectroscopy, and the electronic properties (current density–voltage response) are characterized using a soft contact liquid metal electrode method based on eutectic gallium–indium alloys (EGaIn). Our results show a substantial 1000-fold increase in current density across SAM junctions upon addition of heme compared to identical peptide sequences in the absence of heme, while maintaining a constant junction thickness. These findings show that amino acid composition and sequence directly control enhancements in electron transport in heme-binding peptides. Overall, this study demonstrates the potential of using sequence-defined synthetic peptides inspired by nature as functional bioelectronic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

UCB current detector experiment on Swedish auroral payloads

A split Langmuir probe has been developed to make in situ measurements of ionospheric current density and plasma bulk flow. The probe consists of two conducting elements that are separated by a thin insulator that shield each other over a 2 pi solid angle, and that are simultaneously swept from negative to positive with respect to the plasma. By measuring the current to each plate and the difference current between plates, information is obtained on the plasma's current density, bulk flow, electron temperature, and density. The instrument was successfully flown twice on sounding rockets into auroral events. Measurement data indicate that the total auroral current configuration is composed of several alternating east and west electrojets associated with several alternating up and down Birkeland currents.

Mozer, F.↗
DOE OSTI2026

Hollow-structured Ni-N-C catalysts for highly selective CO 2 electroreduction

Atomically dispersed single-atom catalysts have emerged as promising non-precious catalyst alternatives to expensive Ag and Au catalysts for electrochemical CO 2 reduction reaction (CO 2 RR). In particular, nickel-nitrogen-carbon (Ni-N-C) catalysts have demonstrated a high faradaic efficiency (FE) toward CO formation at low overpotentials. Nonetheless, the exact nature of Ni active sites under CO 2 RR remains elusive and conventional Ni-N-C catalysts are limited by microporosity and low density of Ni single atoms, hindering performance in CO 2 electrolyzers. Here, we report the synthesis of hollow-structured Ni-N-C ( hs -Ni-N-C) catalysts via a post-synthesis modification (PSM) strategy using partial ligand exchange of 2-methylimidazole with 3-amino-1,2,4-triazole. This approach enables the formation of a hollow structure, resulting in more than a twofold increase in Ni atom density compared to regular Ni-N-C (r-Ni-N-C). In a zero-gap CO 2 electrolyzer, the optimized hs -Ni-N-C allows for achieving an FE CO of 97% at a current density of > 100 mA cm⁻ 2 , while maintaining high CO selectivity with stable performance over 100 h at 2.5 V. hs-Ni-N-C shows a more than sevenfold increase in the CO partial current density relative to r-Ni-N-C resulting from the combined effects of a higher density of Ni single-atom sites, improved kinetics, and lower transport resistance under the operating conditions, as indicated by electrochemical impedance spectra and distribution of relaxation times analysis. Operando high energy-resolution X-ray absorption spectroscopy (XAS) reveals that atop-bonded CO on Ni single sites induces dynamic transformations of the Ni–N coordination environment, leading to a symmetric coordination structure of hs -Ni-N-C. Under CO 2 RR, the catalysts undergo a more pronounced structural change and form a minor fraction of Ni nanoparticles. Density functional theory calculations are consistent with the XAS results and provide molecular insights showing that the interplay between protonation and CO adsorption leads to adsorbate-induced restructuring of the Ni single atom. This work demonstrates the synergistic role of hollow structure and high-density Ni atoms in governing CO 2 RR selectivity and provides mechanistic insights into the structural dynamics of single-atom catalysts under operating conditions.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Reduction in bearing size due to superconductors in magnetic bearings

A design concept that reduces the size of magnetic bearings is assessed. The small size will enable magnetic bearings to fit into limited available bearing volume of cryogenic machinery. The design concept, called SUPERC, uses (high Tc) superconductors or high-purity aluminum conductors in windings instead of copper. The relatively high-current density of these conductors reduces the slot radial thickness for windings, which reduces the size of the bearings. MTI developed a sizing program called SUPERC that translates the high-current density of these conductors into smaller sized bearings. This program was used to size a superconducting bearing to carry a 500 lb. load. The sizes of magnetic bearings needed by various design concepts are as follows: SUPERC design concept = 3.75 in.; magnet-bias design concept = 5.25 in.; and all electromagnet design concept = 7.0 in. These results indicate that the SUPERC design concept can significantly reduce the size of the bearing. This reduction, in turn, reduces the weight and yields a lighter bearing. Since the superconductors have inherently near-zero resistance, they are also expected to save power needed for operation considerably.

Rao, Dantam K.↗
DOE OSTI2023

Interface Design for High‐Performance All‐Solid‐State Lithium Batteries

All‐solid‐state batteries suffer from high interface resistance and lithium dendrite growth leading to low Li plating/stripping Coulombic efficiency (CE) of <90% and low critical current density at high capacity. Here, in this work, both challenges are simultaneously addressed and the Li plating/stripping CE is significantly increased to 99.6% at 0.2 mA cm −2 /0.2 mAh cm −2 , and critical current density (CCD) of > 3.0 mA cm −2 /3.0 mAh cm −2 by inserting a mixed ionic‐electronic conductive (MIEC) and lithiophobic LiF‐C‐Li 3 N‐Bi nanocomposite interlayer between Li 6 PS 5 Cl electrolyte and Li anode. The highly lithiophobic LiF‐C‐Li 3 N‐Bi interlayer with high ionic conductivity (10 −5 S cm −1 ) and low electronic conductivity (3.4×10 −7 S cm −1 ) enables Li to plate on the current collector (CC) surface rather than on Li 6 PS 5 Cl surface avoiding Li 6 PS 5 Cl electrolyte reduction. During initial Li plating on CC, Li penetrates into porous LiF‐C‐Li 3 N‐Bi interlayer and lithiates Bi nanoparticles into Li 3 Bi. The lithiophilic Li 3 Bi and Li 3 N nanoparticles in LiF‐C‐Li 3 N‐Li 3 Bi sub‐interlayer will move to CC along with plated Li, forming LiF‐C/Li 3 N‐Li 3 Bi lithiophobic/lithiophilic sublayer during the following Li stripping. This interlayer enables Co 0.1 Fe 0.9 S 2 /Li 6 PS 5 Cl/Li cell with an areal capacity of 1.4 mAh cm −2 to achieve a cycle life of >850 cycles at 150 mA g −1 . The lithiophobic/lithiophilic interlayer enables solid‐state metal batteries to simultaneously achieve high energy and long cycle life.

25 ENERGY STORAGE↗