Search NASA⌕ Search

SEARCH · Search NASA

Results for “large loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

The Impact of Operational Strategies and Load Fluctuations on Anion Exchange Membrane Water Electrolyzer Degradation

This study reports on the durability of anion exchange membrane water electrolyzers (AEMWEs) at the cell level in a supporting electrolyte (1 M) and the impact of operational profiles on cell degradation. While constant load shows significant voltage loss, including a current hold at 1 A cm −2 and a potential hold at 2 V, it generally occurs in the first 70 h of testing. These losses are likely due to passivation altering site reactivity and cell kinetics, and are largely recoverable upon load cycling and diagnostics at the end of test. Furthermore, square and triangular-wave cycling do not show cell degradation and indicate that AEMWEs are not vulnerable to load cycling. When operating outside of this potential window (1.45–2 V), cell voltage decay rates markedly increase and the losses are not recoverable. This includes a current density hold at 4.0 A cm −2 with high cell voltages (>2.4 V for test duration) and cycling between 0 and 2 V to simulate start–stop, where more than a 50% loss in current density occurs over 50 h. The findings presented here demonstrate the high durability of AEMWEs, particularly when operating with load fluctuations, and may allow for durability advantages compared to iridium and proton exchange membrane systems.

08 HYDROGEN↗
NASA NTRS1985

Substructure coupling in the frequency domain

Frequency domain analysis was found to be a suitable method for determining the transient response of systems subjected to a wide variety of loads. However, since a large number of calculations are performed within the discrete frequency loop, the method loses it computational efficiency if the loads must be represented by a large number of discrete frequencies. It was also discovered that substructure coupling in the frequency domain work particularly well for analyzing structural system with a small number of interface and loaded degrees of freedom. It was discovered that substructure coupling in the frequency domain can lead to an efficient method of obtaining natural frequencies of undamped structures. It was also found that the damped natural frequencies of a system may be determined using frequency domain techniques.

Source record↗
NASA NTRS2016

Active Control of Solar Array Dynamics During Spacecraft Maneuvers

Recent NASA mission plans require spacecraft to undergo potentially significant maneuvers (or dynamic loading events) with large solar arrays deployed. Therefore there is an increased need to understand and possibly control the nonlinear dynamics in the spacecraft system during such maneuvers. The development of a nonlinear controller is described. The utility of using a nonlinear controller to reduce forces and motion in a solar array wing during a loading event is demonstrated. The result is dramatic reductions in system forces and motion during a 10 second loading event. A motion curve derived from the simulation with the closed loop controller is used to obtain similar benefits with a simpler motion control approach.

nonlinear controls↗
NASA NTRS1975

Evaluation of bead-stiffened metal panels

Potential weight efficiency for bead-stiffened panels has been demonstrated through fabrication and testing. Theoretically optimum design concepts were identified, and small specimens were tested under combined compression, shear, and bending to determine local buckling failure loads and to verify theory. Large optimized panels were then designed and tested under combined loads. Correlation of test data for large circular tubular panels with theory was conservative and consistent, and indicated reliable and acceptable design theory. Tests of fluted tubular panels indicated general instability failures at loads far below the design values due to nonlinear distortions. Further study of the fluted tubular configuration will be required if its potential weight efficiency is to be attained.

Shideler, J. L.↗
NASA NTRS1974

Interactive design of large end rings on stiffened conical shells using composites

Design study methods and results for a composite reinforced base ring for the conical aeroshell structure of the planetary lander vehicle for Project Viking, an unmanned mission to Mars, are presented. The aeroshell is a ring and stringer-stiffened conical shell structure having a half angle of 70 degrees with a large base ring mounted at the outer edge of the cone and a large pay-load ring in the interior with many smaller rings spaced along the inside shell surface. The purpose of the structure is to develop the aerodynamic drag required to decelerate the lander in the Mars atmosphere to facilitiate a soft landing. The design of a shell structure of this complexity requires the use of the latest technology available in a large general-purpose shell buckling program. The large general-purpose non-linear shell buckling program (BOSOR 2) which was used for this purpose is described.

Davis, R. C.↗
NASA NTRS1985

Evaluation of an aerodynamic-load prediction method on a STOL fighter configuration

A three-dimensional panel method was used to compute the aerodynamic loads on a large-scale, powered wind tunnel model. The size of the computation grid was selected such that turnaround times, on present computers remained satisfactory. With this constraint, the STOL aircraft configuration was modeled and the capabilities and limitations of the prediction method were investigated. After this study, a similar numerical model was established for a forward-swept-wing aircraft configuration which is planned for large-scale, low-speed testing. The resulting aerodynamic-load predictions are discussed and will be utilized, together with the future experimental results, to obtain a broader validation of this method as well as to reduce the necessary size of the matrix of the test parameters.

Katz, J.↗
NASA NTRS1986

The impact of physical and mental tasks on pilot mental workoad

Seven instrument-rated pilots with a wide range of backgrounds and experience levels flew four different scenarios on a fixed-base simulator. The Baseline scenario was the simplest of the four and had few mental and physical tasks. An activity scenario had many physical but few mental tasks. The Planning scenario had few physical and many mental taks. A Combined scenario had high mental and physical task loads. The magnitude of each pilot's altitude and airspeed deviations was measured, subjective workload ratings were recorded, and the degree of pilot compliance with assigned memory/planning tasks was noted. Mental and physical performance was a strong function of the manual activity level, but not influenced by the mental task load. High manual task loads resulted in a large percentage of mental errors even under low mental task loads. Although all the pilots gave similar subjective ratings when the manual task load was high, subjective ratings showed greater individual differences with high mental task loads. Altitude or airspeed deviations and subjective ratings were most correlated when the total task load was very high. Although airspeed deviations, altitude deviations, and subjective workload ratings were similar for both low experience and high experience pilots, at very high total task loads, mental performance was much lower for the low experience pilots.

Berg, S. L.↗
NASA NTRS1986

Evaluation of an aerodynamic-load prediction method on a STOL fighter configuration

A three-dimensional panel method was used to compute the aerodynamic loads on a large-scale, powered wind tunnel model. The size of the computation grid was selected such that turnaround times, on present computers remained satisfactory. With this constraint, the STOL aircraft configuration was modeled and the capabilities and limitations of the prediction method were investigated. After this study, a similar numerical model was established for a forward-swept-wing aircraft configuration which is planned for large-scale, low-speed testing. The resulting aerodynamic-load predictions are discussed and will be utilized, together with the future experimental results, to obtain a broader validation of this method as well as to reduce the necessary size of the matrix of the test parameters.

Katz, J.↗
NASA NTRSDate not supplied

Parametric Study of the Forward Attachment Geometry for the Space Launch System Next Generation Booster

Launch vehicle transonic buffet environments can generate large dynamic structural loads and vibratory responses. For the Space Launch System (SLS) vehicle, the highest transonic buffet environments have been observed in the multibody region between the core and solid rocket boosters, particularly downstream of the booster forward attachment. The buffet environment is particularly sensitive to the outer mold line (OML) of the forward attachment, and even relatively minor geometry changes can have large impacts on buffet and other aerodynamic environments. The SLS program is redesigning the booster for the Block 2 vehicle to support updated mission goals. This redesign necessitated changes in the forward attachment geometry, which raised concerns about the buffet and vibroacoustic environments. A preliminary study was conducted that developed multiple forward attachment geometries that satisfied the programmatic requirements, but the aerodynamic environment impacts were unclear. In March 2022, a wind-tunnel test was conducted at the NASA Ames 11- by 11-foot Transonic Wind Tunnel to study these environments generated from each of the configurations in order to select the most viable candidate. This paper will discuss this test campaign, the results from the parametric study, as well as general observations regarding OML features that impact the buffet environment. Buffet environments will be presented and compared for each configuration and comparisons presented where applicable.

buffet↗
NASA NTRSDate not supplied

Parametric Study of the Forward Attachment Geometry for the Space Launch System Next Generation Booster

Launch vehicle transonic buffet environments can generate large dynamic structural loads and vibratory responses. For the Space Launch System (SLS) vehicle, the highest transonic buffet environments have been observed in the multibody region between the core and solid rocket boosters, particularly downstream of the booster forward attachment. The buffet environment is particularly sensitive to the outer mold line (OML) of the forward attachment, and even relatively minor geometry changes can have large impacts on buffet and other aerodynamic environments. The SLS program is redesigning the booster for the Block 2 vehicle to support updated mission goals. This redesign necessitated changes in the forward attachment geometry, which raised concerns about the buffet and vibroacoustic environments. A preliminary study was conducted that developed multiple forward attachment geometries that satisfied the programmatic requirements, but the aerodynamic environment impacts were unclear. In March 2022, a wind-tunnel test was conducted at the NASA Ames 11- by 11-foot Transonic Wind Tunnel to study these environments generated from each of the configurations in order to select the most viable candidate. This paper will discuss this test campaign, the results from the parametric study, as well as general observations regarding OML features that impact the buffet environment. Buffet environments will be presented and compared for each configuration and comparisons presented where applicable.

buffet↗
NASA NTRS1968

Flight Test of a 40-Foot Nominal Diameter Disk-Gap-Band Parachute Deployed at a Mach Number of 2.72 and a Dynamic Pressure of 9.7 Pounds per Square Foot

A 40-foot-nominal-diameter (12.2 meter) disk-gap-band parachute was flight tested as part of the NASA Supersonic Planetary Entry Decelerator (SPED-I) Program. The test parachute was deployed from an instrumented payload by means of a deployment mortar when the payload was at an altitude of 158,500 feet (48.2 kilometers), a Mach number of 2.72, and a free-stream dynamic pressure of 9.7 pounds per foot(exp 2) (465 newtons per meter(exp 2)). Suspension line stretch occurred 0.46 second after mortar firing and the resulting snatch force loading was -8.lg. The maximum acceleration experienced by the payload due to parachute opening was -27.2g at 0.50 second after the snatch force peak for a total elapsed time from mortar firing of 0.96 second. Canopy-shape variations occurred during the higher Mach number portion of the flight test (M greater than 1.4) and the payload was subjected to large amplitude oscillatory loads. A calculated average nominal axial-force coefficient ranged from about 0.25 immediately after the first canopy opening to about 0.50 as the canopy attained a steady inflated shape. One gore of the test parachute was damaged when the deployment bag with mortar lid passed through it from behind approximately 2 seconds after deployment was initiated. Although the canopy damage caused by the deployment bag penetration had no apparent effect on the functional capability of the test parachute, it may have affected parachute performance since the average effective drag coefficient of 0.48 was 9 percent less than that of a previously tested parachute of the same configuration.

EXPERIMENTS↗
NASA NTRS1990

Development of load-dependent Ritz vector method for structural dynamic analysis of large space structures

The development and preliminary assessment of a method for dynamic structural analysis based on load-dependent Ritz vectors are presented. The vector basis is orthogonalized with respect to the mass and structural stiffness in order that the equations of motion can be uncoupled and efficient analysis of large space structure performed. A series of computer programs was developed based on the algorithm for generating the orthogonal load-dependent Ritz vectors. Transient dynamic analysis performed on the Space Station Freedom using the software was found to provide solutions that require a smaller number of vectors than the modal analysis method. Error norm based on the participation of the mass distribution of the structure and spatial distribution of structural loading, respectively, were developed in order to provide an indication of vector truncation. These norms are computed before the transient analysis is performed. An assessment of these norms through a convergence study of the structural response was performed. The results from this assessment indicate that the error norms can provide a means of judging the quality of the vector basis and accuracy of the transient dynamic solution.

Ricles, James M.↗
NASA NTRS1980

Performance of a steel spar wind turbine blade on the Mod-0 100 kW experimental wind turbine

The performance and loading of a large wind rotor, 38.4 m in diameter and composed of two low-cost steel spar blades were examined. Two blades were fabricated at Lewis Research Center and successfully operated on the Mod-0 wind turbine at Plum Brook. The blades were operated on a tower on which the natural bending frequency were altered by placing the tower on a leaf-spring apparatus. It was found that neither blade performance nor loading were affected significantly by this tower softening technique. Rotor performance exceeded prediction while blade loads were found to be in reasonable agreement with those predicted. Seventy-five hours of operation over a five month period resulted in no deterioration in the blade.

Keith, T. G., Jr.↗
NASA NTRS1998

Three-Component Force Measurements on a Scramjet in a Reflected-Shock Tunnel

A three-component stress-wave force-balance for a large scramjet has been designed, calibrated and tested in the HYPULSE reflected shock tunnel at GASL Inc., New York. The scramjet model is over 3-foot long and weighs in excess of 90 Ibm. The stress-wave force-balance is comprised of three stress bars which are attached to the model. Calibration results indicate that the force balance responds well within about 1 ms and that the sensitivity of the balance to the distribution of load is not large. Results with and without fuel injection were obtained in the tunnel operated for Mach 7 and Mach 10 flight simulation. These tests showed the force-balance can resolve axial force increments due to combustion of about 40 lb in the presence of model lift forces of 500-700 lb.

Tsai, C.-Y.↗
DOE OSTI2024

Deep-Learning-Based Multi-Timescale Load Forecasting in Buildings: Opportunities and Challenges from Research to Deployment

Electricity load forecasting for buildings and campuses is becoming increasingly important as the penetration of distributed energy resources (DERs) grows. Efficient operation and dispatch of DERs require reasonably accurate predictions of future energy consumption in order to conduct near-real-time optimized dispatch of on-site generation and storage assets. Electric utilities have traditionally performed load forecasting for load pockets spanning large geographic areas, and therefore, forecasting has not been a common practice by buildings and campus operators. Given the growing trends of research and prototyping in the grid-interactive efficient buildings domain, characteristics beyond simple algorithm forecast accuracy are important in determining the algorithm's true utility for smart buildings. Other characteristics include the overall design of the deployed architecture and the operational efficiency of the forecasting system. In this work, we present a deep-learning-based load forecasting system that predicts the building load at 1-hour intervals for 18 hours in the future. We also discuss challenges associated with the real-time deployment of such systems as well as the research opportunities presented by a fully functional forecasting system that has been developed within the National Renewable Energy Laboratory's Intelligent Campus program.

building load forecasting↗
NASA NTRS1971

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations. Phase 5A: Effects of torsional blade flexibility on single blade random gust response statistics

Quasi-steady aerodynamics were assumed, as well as a torsion mode where the amplitude is proportional to the distance from the rotor center. Aerodynamic torsional moment inputs are limited to the region of reverse flow where the aerodynamic center and the section center of gravity are separated by half the blade chord. Thus negligible effects of blade torsional flexibility are obtained for rotor conditions with negligible reverse flow effects. Numerical examples refer to conditions with 1.6 rotor advance ratio. It was found that the random flapping response is only moderately affected by torsional flexibility. However large random torsional loads and deflections occur even if flapping is completely suppressed. The coupling of the actual flapping motion into the blade torsional motion produces a substantial increase in the random torsional loads or deflections.

Hohenemser, K. H.↗
DOE OSTI2025

Software For Advanced Large-scale Analysis Of Magnetic Confinement For Numerical Design, Engineering & Research (salamander)

As magnetic confinement fusion energy gains traction internationally to enable abundant energy production, designing components for fusion systems is a pressing challenge. During the planned lifetime of a fusion device, components evolve in extreme environments and must withstand large, repeated thermal loads and bombardment by 14 MeV neutrons, plasma ions, and neutral particles (deuterium, tritium, and helium), corrosive conditions, etc. All these physical processes take place simultaneously, interact in intricate ways, and impose important constraints that can affect performance. Experimental data is rare and costly to obtain, making design particularly challenging. Predictive computational frameworks must be an integral part of an accelerated and cost-effective design process by modeling fusion system performance in simulated environments. To better understand component degradation and operational impacts on their performance, the Software for Advanced Large-scale Analysis of MAgnetic confinement for Numerical Design, Engineering & Research (SALAMANDER) is designed as an open-source, fully integrated, multiphysics, multiscale, NQA-1 compliant framework facilitating 3D, high-fidelity fusion system modeling. To that end, SALAMANDER is a MOOSE-based framework, and therefore leverages MOOSE upstream libraries such as PETSc and libMesh to deliver sophisticated finite element, finite volume, and nonlinear solver technology for fusion energy simulations. SALAMANDER couples MOOSE physics module capabilities—such as thermal hydraulics, heat conduction, Navier-Stokes, and thermomechanics—with tritium transport via TMAP8, neutronics via Cardinal, and nascent particle-in-cell capabilities. Direct simulation Monte Carlo methods will be used to address neutral transport near the walls. By coupling all these physics in an integrated application, SALAMANDER will enable high-fidelity modeling of irradiation levels and plasma exposure conditions of plasma facing components and their impact on heat and tritium distributions, as well as the resulting mechanical constraints experienced by the plasma facing components and performance of blanket systems. Furthermore, SALAMANDER will be particularly suited for engineering studies thanks to the stochastic tool module readily available in MOOSE, allowing for extended uncertainty quantification and risk analysis studies. It is also able to use computer-aided design (CAD) meshes to model complex geometries, which is indispensable for fusion systems. SALAMANDER therefore supports design, safety, engineering, and research projects for magnetic confinement fusion systems

Simon, Pierre-Clement [Idaho National Laboratory (↗
NASA NTRS2013

Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy: Isothermal Creep - Part I

This two-part paper is the first published report on the long term, low temperature creep of hot-extruded near-stoichiometric NiTi. Constant load tensile creep tests were conducted on hot-extruded near-stoichiometric NiTi at 300, 373 and 473 K under initial applied stresses varying between 200 and 350 MPa as long as 15 months. These temperatures corresponded to the martensitic, two-phase and austenitic phase regions, respectively. Normal primary creep lasting several months was observed under all conditions indicating dislocation activity. Although steady-state creep was not observed under these conditions, the estimated creep rates varied between 10(exp -10) and 10(exp -9)/s. The creep behavior of the two phases showed significant differences. The martensitic phase exhibited a large strain on loading followed by a primary creep region accumulating a small amount of strain over a period of several months. The loading strain was attributed to the detwinning of the martensitic phase whereas the subsequent strain accumulation was attributed to dislocation glide-controlled creep. An "incubation period" was observed before the occurrence of detwinning. In contrast, the austenitic phase exhibited a relatively smaller loading strain followed by a primary creep region, where the creep strain continued to increase over several months. It is concluded that the creep of the austenitic phase occurs by a dislocation glide-controlled creep mechanism as well as by the nucleation and growth of deformation twins.

Raj, S. V.↗