SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Use of time-to-failure curves for stress-corrosion cracking processes may lead to incorrect estimates of structural life, if material is strongly dependent upon prestress levels. Technique characterizes kinetics of crackgrowth rates and intermediate arrest times by load-level changes.
The analysis of aerospace structures by the finite element method consumes considerable computer time. The cost of this resource and the designer's desire to have rapid feedback concerning such questions as the effect of a change in loading of the structure or in a parameter of some structural material led to the design of a special purpose parallel computing system for finite element analysis. As a special purpose computer, the architecture of this finite element computer is closely tied to computational aspects of the particular problem. Various aspects of an MIMD array of microprocessors are related to the requirements of the class of finite element analysis problems which it is intended to solve.
As an alternative to alleviating wing/store flutter by conventional passive methods or by more advanced active control methods, a quasi-passive concept, referred to as the decoupler pylon, is investigated which combines desirable features of both methods. Passive soft-spring/damper elements are used to decouple wing modes from store pitch modes, and a low-power control system maintains store alignment under changing mean loads. It is shown by analysis and wind tunnel tests that the decoupler pylon provides substantial increase in flutter speed and makes flutter virtually insensitive to inertia and center-of-gravity location of the store.
Recent wind tunnel tests and analytical studies show that a store mounted on a pylon with soft pitch stiffness provides substantial increase in flutter speed of fighter aircraft and reduces dependency of flutter on mass and inertia of the store. This concept, termed the decoupler pylon, utilizes a low frequency control system to maintain pitch alignment of the store during maneuvers and changing flight conditions. Under rapidly changing transient loads, however, the alignment control system may allow the store to momentarily bottom against a relatively stiff backup structure in which case the pylon stiffness acts as a hardening nonlinear spring. Such structural nonlinearities are known to affect not only the flutter speed but also the basic behavior of the instability. The influence of pylon stiffness nonlinearities or the flutter characteristics of wing mounted external stores is examined.
Recent wind tunnel tests and analytical studies show that a store mounted on a pylon with 'soft' pitch stiffness provides substantial increase in flutter speed of fighter aircraft and reduces dependency of flutter on mass and inertia of the store. This concept, termed the decoupler pylon, utilizes a low-frequency control system to maintain pitch alignment of the store during maneuvers and changing flight conditions. Under rapidly changing transient loads, however, the alignment control system may allow the store to momentarily bottom against a relatively stiff backup structure in which case the pylon stiffness acts as a hardening nonlinear spring. Such structural nonlinearities are known to affect not only the flutter speed but also the basic behavior of the instability. This paper examines the influence of pylon stiffness nonlinearities on the flutter characteristics of wing-mounted external stores.
An experimental investigation of the effects of the speed of rotation on a turbomachinery rotor blade wake was conducted using a fan rotor in incompressible flow. Measurements were made at two different rotational speeds (1753 and 1010 rpm) but keeping the same blade loading. This was achieved by maintaining the same incidence angle to the rotor blades in both sets of measurements. The blade incidence angle was also varied to discern the effect of blade loading. A tri-axial hot wire probe mounted in a stationary frame of reference was used for the measurements made at several radial and axial stations in the near- and far-wake regions. The three dimensional mean velocity and turbulence profiles, the wake defect, wake decay rate, turbulence intensities and turbulence stresses are appreciably altered when the speed of rotation and the blade loading are changed. The wake defect is substantially reduced and the radial velocity increased when the rotational speed is increased.
A device for suspending a store from a support such as an aircraft wing and more specifically for increasing the flutter speed of an aircraft flying with attached store and reducing the sensitivity of flutter to changes in the pitch inertia and center of gravity location of the store is described. It comprises softspring where the store pitch mode is decoupled from support modes and a low frequency active control mechanism which maintains store alignment. A pneumatic suspension system both isolates the store in pitch and, under conditions of changing mean load, aligns the store with the wing to which it is attached.
For any piece of hardware that degrades when subject to environmental and application stresses, the route or sequence that describes the degradation process may be summarized in terms of six key words: LOADS, RESPONSE, CHANGE, DAMAGE, FAILURE, and PENALTY. Applied to photovoltaic modules, these six factors form the core outline of an expanded failure analysis matrix for unifying and integrating relevant material degradation data and analyses. An important feature of this approach is the deliberate differentiation between factors such as CHANGE, DAMAGE, and FAILURE. The application of this outline to materials degradation research facilitates the distinction between quantifying material property changes and quantifying module damage or power loss with their economic consequences. The approach recommended for relating material stability data to photovoltaic module life is to use the degree of DAMAGE to (1) optical coupling, (2) encapsulant package integrity, (3) PV circuit integrity or (4) electrical isolation as the quantitative criterion for assessing module potential service life rather than simply using module power loss.
Computer program enables real-time data acquisition and plotting of stress strain by small, desk top computer. Program monitors load cell and multiple-strain gages during tension or compression loading. Scan routine triggered by specified change of applied load or longitudinal strain.
An analytic study is presented of the effects of phase change on load support for parallel and tapered face seals. Consideration is given to an adiabatic model for low Reynolds number flow. Numerical integration is carried out of the descriptive fluid equations, giving the opening force due to fluid film pressure. The loci of steady-state solutions are then plotted for water to provide curves of load support as a function of film thickness. For axial excursions of the seal rings, a quasi-steady transient analysis is made. It is found that the load support generated by fluid pressure can be multivalued for a given film thickness. Another finding is that axial disturbances of the seal rings may lead to sudden drops in load support generated by fluid pressure with three possible results. The first is that sufficient damping may permit the seal to return to the previous equilibrium operating position. The second is that the seal may collapse to an equilibrium position of smaller film thickness where face contact is more likely and a significantly higher operating temperature is assured. The third is that a limit cycle of self-sustained oscillation in the axial direction may occur if damping is sufficiently low.
The present report describes numerical simulation of three-dimensional transient distributions of velocity and temperature of liquid oxygen (LOX) in the LOX Dewar tank of Vendenberg Air Force Base (VAFB). The present analyses cover the replenish time period only. Four test cases have been considered. For all four cases, the input boundary conditions are comprised of LOX facility heat loads, drain flow rates, recirculation flow rates and dewar heating. All the quantities are prescribed as functions of time. The first two test cases considered sensitivity of results to the computational grid. In Case 3, system heat load was changed, while in Case 4, a lower LOX level was specified. Cases 1 and 2 showed that the temperatures were not sensitive to the grid refinement. This provided a basic check on the numerical model. Cases 3 and 4 showed that the thermal boundary layer motion near the tank surface becomes more significant at the late time, e.g., 5 1/2 hours from replenish start. Comparison between results of Cases 3 and 4 showed, as expected, that the smaller initial LOX volume given in Case 4, results in higher temperature level. All calculated velocity and temperature distributions were found to be plausible.
Large forces accommodated without increasing weight of helicopter structure. New mechanism yields stiffer control and improves accuracy of pitch changes under load. As result, heavy casting not for gearbox, nor extra reinforcing members needed for fuselage bulkheads, stringers, skin, and other parts. In new mechanism, reaction forces developed in rotor hub. Long load paths to gearbox and fuselage elminated. Reaction member rigidly attached to hub and rotates with it. At lower end of reaction member, bearing forms bridge to fuselage through stationary beam and antirotation link. Beam connected to reaction plate through rods.
The distribution of flight loads on an aircraft structure determines the lift and pitching moment characteristics of the aircraft. When the load distribution changes due to the aeroelastic response of the structure, the lift and pitching moment characteristics also change. Some estimate of the effect of aeroelasticity on stability and control characteristics, particularly lift and pitching moment, is required for use in aircraft simulation models for evaluation of flight characteristics. This presentation outlines a procedure to incorporate aeroelastic effects into lift and pitching moment data from wind tunnel tests. Results are presented which were obtained from applying this procedure to an aircraft with a very flexible transport-type research wing. The procedure described is generally applicable to all types of aircraft.
Analysis techniques to evaluate the effects of changing thermal loads and the methods utilized to control temperature distributions in the orbital space station are essential. Analysis techniques including a user-friendly computer program, were developed which should prove useful in thermal design and system analysis of the the space station. The program uses a data base and user input to compute costs, sizes, and power requirements for individual components and complete systems. User input consists of selecting mission parameters, selecting thermal acquisition configurations, transport systems and distances, and thermal rejection configurations.
The distribution of flight loads on an aircraft structure determine the lift and pitching moment characteristics of the aircraft. When the load distribution changes due to the aeroelastic response of the structure, the lift and pitching moment characteristics also change. An estimate of the effect of aeroelasticity on stability and control characteristics is often required for the development of aircraft simulation models of evaluation of flight characteristics. This presentation outlines a procedure for incorporating calculated linear aeroelastic effects into measured nonlinear lift and pitching moment data from wind tunnel tests. Results are presented which were obtained from applying this procedure to data for an aircraft with a very flexible transport type research wing. The procedure described is generally applicable to all types of aircraft.
Optimum sensitivity is defined as the derivative of the optimum design with respect to some problem parameter, P. The problem parameter is usually fixed during optimization, but may be changed later. Thus, optimum sensitivity is used to estimate the effect of changes in loads, materials or constraint bounds on the design without expensive re-optimization. Here, the general topic of optimum sensitivity is discussed, available methods identified, examples given, and the difficulties encountered in calculating this information in nonlinear constrained optimization are identified.
The distribution of flight loads on an aircraft structure determine the lift and pitching moment characteristics of the aircraft. When the load distribution changes due to the aeroelastic response of the structure, the lift and pitching moment characteristics also change. An estimate of the effect of aeroelasticity on stability and control characteristics is often required for the development of aircraft simulation models of evaluation of flight characteristics. This presentation outlines a procedure for incorporating calculated linear aeroelastic effects into measured nonlinear lift and pitching moment data from wind tunnel tests. Results are presented which were obtained from applying this procedure to data for an aircraft with a very flexible transport type research wing. The procedure described is generally applicable to all types of aircraft.
Hardware implementation of the NASA ACTS baseband processor is described which achieves the system message data handling performance required to perform satellite switching of high-rate baseband data. The hardware meets payload specifications for size, weight, and power. Hardware redundancy applied to critical paths in several functional areas insures that the reliability and life expectancy requirements are fulfilled. The remote reprogrammability of the processor message data handling and routing functions provides system flexibility for dynamic reconfiguration during rapidly changing traffic loads.