Search NASA⌕ Search

SEARCH · Search NASA

Results for “selective dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Microstructure, precipitates and hardness of selectively laser melted AlSi10Mg alloy before and after heat treatment

Highlights: • Microstructural characterization of SLM AlSi10Mg alloy and comparison with cast and powder AlSi10Mg • Effect of solution heat treatment and aging on the hardness change of SLM AlSi10Mg alloy • Evolution of strengthening precipitates and Fe-rich intermetallics in SLM AlSi10Mg during heat treatment - Abstract: The microstructure and precipitates within selectively laser melted (SLM) AlSi10Mg alloys in the as-built state and after T6 heat treatment were examined and correlated to the hardness evolution. The as-built alloy exhibited columnar patterns perpendicular to the build-direction and fish-scale pattern along the build-direction originating from the melt pool. The microstructure consisted of fine Al cells and eutectic structure with up to 4 μm in size. Tiny needle-like Si particles with highly faulted structure were identified within the Al cells and formed semi-coherent interface with the matrix. Nanoscale Si particles and π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase were observed to segregate along the cell and grain boundary. Solution heat treatment (SHT) at 520 °C resulted in the dissolution of Al cellular microstructure. Precipitation and coarsening of the Si particles occurred, while the aspect ratio of Si particles remained nearly constant. The π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase decomposed into plate-shaped β-Al{sub 5}SiFe. The artificial aging (AA) at 160 °C did not alter the microstructure but led to the formation of metastable Mg{sub 2}Si precipitates. The GP zones and β″ were identified through transmission electron microscopy after AA of 6 h, and β″ existed up to AA of 24 h. The hardness decreased after SHT due to the coarsening of the microstructure and reduced solid solution hardening. Hardness reached maximum magnitude after AA of 6–10 h due to the precipitation hardening, and remained relatively unchanged up to AA of 24 h. Microstructure and/or hardness of gas atomized powders and bulk cast AlSi10Mg alloys were also examined as references.

36 MATERIALS SCIENCE↗

Accelerated Transport of 90Sr Following a Release of High Ionic Strength Solution in Vadose Zone Sediments

Numerical simulation of cation exchange and mineral precipitation / dissolution reactions using the multiphase reactive geochemical transport code TOUGHREACT has provided important insight into the distribution of 90Sr between layers of geologic strata in a complex vadose zone at the U. S. Department of Energy’s Idaho National Laboratory. During a transfer operation in November 1972, 70.4 m3 of acidic, high ionic strength liquid containing 15,900 Ci of 90Sr was released over five days into alluvial gravels 137 m above the Snake River Plain Aquifer. Sampling data from perched water zones 33 m below the release contain very high levels of 90Sr as do soil samples obtained nearer the point of release. Use of traditional simulation approaches using laboratory measured constant partitioning coefficients (Kd) cannot simultaneously explain perched water and soil concentrations. To address the discrepancy, a reactive transport approach was adopted to include competitive cation exchange, dissolution / precipitation of calcite, carbon dioxide gas production and transport, and gibbsite precipitation. Simulation results using this model suggest that some of the 90Sr could have been transported very rapidly immediately after the release with the acceleration facilitated by competition with high sodium concentrations in the released liquid, by calcium dissolved from calcite, and to a lesser extent by formation of aqueous complexes with nitrate. It is known that once the leading edge of the liquid assemblage was flushed from the alluvium, the mobility of the remaining 90Sr decreased significantly in the absence of the competing cations. Calculations indicate that there should be a net increase in calcite, suggesting that 90Sr could be entrained in the mineral lattice, but insufficient field data exists for confirmation. Sensitivity studies show that the ion exchange capacity and the Na/Sr ion exchange selectivity coefficients were the most sensitive parameters. Because of the sensitivity to total ion exchange capacity, 90Sr migration was found to be very sensitive to the combination of sediment cation exchange capacity and the area wetted by the infiltrating solution. In contrast, the future mobility of 90Sr was found to be relatively insensitive to the normal range in the composition of influxing precipitation and anthropogenic waters.

58 GEOSCIENCES↗

Influence of severe plastic deformation on intermetallic particles in Mg-12 wt.%Zn alloy investigated using transmission electron microscopy

The in-depth microstructural characterization of intermetallic particles in an Mg-12 wt.%Zn binary alloy subjected to a severe plastic deformation is presented. The alloy was processed by four passes via equal channel angular pressing with an applied back pressure at a gradually decreasing temperature and analyzed using transmission electron microscopy techniques to observe the influence of processing on intermetallic particles. The results are compared with the initial state of the material prior to severe plastic deformation. The microstructural evolution of the α-Mg matrix and the Mg{sub 21}Zn{sub 25}, Mg{sub 51}Zn{sub 20} and MgZn{sub 2} was analyzed using bright field imaging, selected area electron diffraction, high-resolution transmission electron microscopy and high-angle annular dark field imaging in scanning mode. The plastic deformation process influenced the α-Mg matrix and each type of intermetallic particle. The α-Mg matrix consisted of two types of areas. The first type of area had a highly deformed structure, and the second type of area had a partially recrystallized structure with an average grain size of approximately 250 nm. The Mg{sub 21}Zn{sub 25} microparticles exhibited distinct forms in the α-Mg matrix that were characterized as a single-crystalline form, a nano-crystalline form and a broken up form. No evidence of Mg{sub 51}Zn{sub 20} nanoparticles within the α-Mg matrix was found in the microstructure, which indicates their dissolution or phase transformation during the deformation process. MgZn{sub 2} nanoparticles exhibited different behavior in both types of α-Mg matrix. Two orientation relationships toward the highly deformed α-Mg matrix were observed; however, there was no relationship toward the partially recrystallized α-Mg matrix. Additionally, the growth of the MgZn{sub 2} nanoparticles was different in the two types of α-Mg matrix. The Mg{sub 51}Zn{sub 20} nanoparticles inside Mg{sub 21}Zn{sub 25} microparticles exhibited a distinct behavior within the single-crystalline or nano-crystalline form of the parent Mg{sub 21}Zn{sub 25} microparticles. The Mg{sub 21}Zn{sub 25} + Mg{sub 51}Zn{sub 20} eutectic compound was confirmed for both forms of the parent Mg{sub 21}Zn{sub 25} microparticles, and the growth of Mg{sub 51}Zn{sub 20} nanoparticles is discussed. - Highlights: •Comprehensive microstructure characterization of Mg-12 wt.%Zn alloy after ECAP-BP •TEM analysis of changes of intermetallic phases caused by SPD •Mg{sub 21}Zn{sub 25} particles exhibit nano-crystalline regions with grain size below 100 nm. •MgZn{sub 2} preserved its orientation relationship toward highly deformed α-Mg after SPD. •Existence of Mg{sub 21}Zn{sub 25} + Mg{sub 51}Zn{sub 20} eutectic remained for each Mg{sub 21}Zn{sub 25} particle form.

36 MATERIALS SCIENCE↗

Chabazite Zeolite Membranes for Krypton/Xenon Separation: Control of Membrane Properties and Process Modeling

Nuclear energy is considered to be a clean and economical means of carbon-free energy. As part of the overall process for recycling used nuclear fuel (UNF), it is necessary to develop technologies to separate the off-gases formed during the fission of uranium and plutonium in nuclear power reactors. The off-gas stream is generated during the shearing and chopping, voloxidation, and acid dissolution steps, and would have a flow rate of ∼2500 L/min assuming a typical 800 tons heavy metal/yr reprocessing facility. Kr separation from Xe is one of the steps in a proposed UNF off-gas processing flowsheet. The Kr/Xe mixture is approximately 10/90 by volume and hence the separation of Kr would reduce the volume of radioactive {sup 85}Kr waste by a factor of 10. Kr/Xe separation is challenging since they are both chemically inert species and physically very similar (0.036 nm size difference). There is no existing process for this separation that is suitable for use in UNF recycling since conventional cryogenic distillation requires highly intensive power and large system volume. Membrane-based separation using radiation-stable materials such as zeolites could be an attractive separation method, if membranes with sufficient Kr flux and selectivity can be fabricated. Zeolite membranes offer an opportunity to exploit the size difference of Kr (kinetic diameter 0.36 nm) and Xe (0.396 nm) to achieve preferential permeation of the minority component (Kr) from the mixture, leading to an efficient separation with very low energy requirements. An ideal membrane process would permeate a stream of pure Kr for storage and also produce pure Xe which has commercial value (> $8000/kg at 99+% purity). SAPO-34 is a silico-alumino-phosphate zeolite molecular sieve with CHA framework topology and containing uniform micropores (0.38 nm), intermediate in size between the kinetic diameters of Kr and Xe. It was hypothesized that SAPO-34 membranes can separate krypton and xenon by diffusivity differences. Previously we fabricated SAPO-34 membranes and showed that they are capable of separating Kr from Xe. Our previous work also indicated that there is much potential for engineering the separation properties of these membranes with a view to improving permeance and selectivity and evaluating the expected process performance. The main objectives of the present study are: 1) development of SAPO-34 membranes with enhanced membrane performance via thickness reduction and ion exchange, and 2) process modeling for technic-economic analysis of zeolite membrane systems for Kr/Xe separation.

36 MATERIALS SCIENCE↗

SAVANNAH RIVER SITE TANK CLEANING: CORROSION RATE FOR ONE VERSUS EIGHT PERCENT OXALIC ACID SOLUTION

Until recently, the use of oxalic acid for chemically cleaning the Savannah River Site (SRS) radioactive waste tanks focused on using concentrated 4 and 8-wt% solutions. Recent testing and research on applicable dissolution mechanisms have concluded that under appropriate conditions, dilute solutions of oxalic acid (i.e., 1-wt%) may be more effective. Based on the need to maximize cleaning effectiveness, coupled with the need to minimize downstream impacts, SRS is now developing plans for using a 1-wt% oxalic acid solution. A technology gap associated with using a 1-wt% oxalic acid solution was a dearth of suitable corrosion data. Assuming oxalic acid's passivation of carbon steel was proportional to the free oxalate concentration, the general corrosion rate (CR) from a 1-wt% solution may not be bound by those from 8-wt%. Therefore, after developing the test strategy and plan, the corrosion testing was performed. Starting with the envisioned process specific baseline solvent, a 1-wt% oxalic acid solution, with sludge (limited to Purex type sludge-simulant for this initial effort) at 75 C and agitated, the corrosion rate (CR) was determined from the measured weight loss of the exposed coupon. Environmental variations tested were: (a) Inclusion of sludge in the test vessel or assuming a pure oxalic acid solution; (b) acid solution temperature maintained at 75 or 45 C; and (c) agitation of the acid solution or stagnant. Application of select electrochemical testing (EC) explored the impact of each variation on the passivation mechanisms and confirmed the CR. The 1-wt% results were then compared to those from the 8-wt%. The immersion coupons showed that the maximum time averaged CR for a 1-wt% solution with sludge was less than 25-mils/yr for all conditions. For an agitated 8-wt% solution with sludge, the maximum time averaged CR was about 30-mils/yr at 50 C, and 86-mils/yr at 75 C. Both the 1-wt% and the 8-wt% testing demonstrated that if the sludge was removed from the testing, there would be a significant increase in the CR. Specifically, the CR for an agitated 1-wt% pure oxalic acid solution at 45 or 75 C was about 4 to 10 times greater than those for a 1-wt% solution with sludge. For 8-wt% at 50 C, the effect was even larger. The lower CRs suggest that the cathodic reactions were altered by the sludge. For both the 1-wt% and 8-wt% solution, increasing the temperature did not result in an increased CR. Although the CR for a 1-wt% acid with sludge was considered to be non-temperature dependent, a stagnant solution with sludge resulted in a CR that was greater at 45 C than at 75 C, suggesting that the oxalate film formed at a higher temperature was better in mitigating corrosion. For both a 1 and an 8-wt% solution, agitation typically resulted in a higher CR. Overall, the testing showed that the general CR to the SRS carbon steel tanks from 1-wt% oxalic acid solution will remain bounded by those from an 8-wt% oxalic acid solution.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DESORPTION OF SORBATES FROM MST, MMST, AND CST UNDER VARIOUS CONDITIONS

The Small Column Ion Exchange (SCIX) Program (formerly referred to as the Modular Salt Processing (MSP) Project) seeks to deploy equipment to remove the {sup 134,137}Cs, {sup 90}Sr, and alpha-emitting radionuclides (principally {sup 238,239,240}Pu and {sup 237}Np) from the high level waste salt solutions. The equipment is installed within a high level waste tank to take advantage of the shielding provided by the waste tank. The process will involve adding monosodium titanate (MST) to the waste tank (i.e., Tank 41H) to sorb the Sr and select actinides, removing the MST and entrained sludge with in-riser rotary microfilters, and subsequently using ion-exchange columns containing crystalline silicotitanate (CST) to remove the Cs. After being loaded with Cs, the CST will be ground to reduce the particle size and then transferred into another waste tank (e.g., Tank 40H). The MST and sludge solids stream will be transported to a sludge batch preparation tank (i.e., Tank 42H or Tank 51H) once the SCIX batch is processed. Both streams, MST/solids and CST, will ultimately be transported into and vitrified inside the Defense Waste Processing Facility (DWPF). A series of experiments were performed to examine desorption from monosodium titanate (MST), modified monosodium titanate (mMST), and crystalline silicotitanate (CST) under various conditions. The first two experiments examined desorption from MST and CST under two different sludge treatment processes, aluminum dissolution and sludge washing. Desorption of all sorbates was observed to varying degrees under the aluminum dissolution conditions. The extent of desorption ranged from < 3% to about 50% after 4 weeks, with Pu exhibiting the lowest desorption. At the end of the experiment, the temperature was reduced from 65 C to 25 C and the tests monitored for an additional two weeks. After reducing the temperature, partial resorption of the sorbates was observed with both MST and CST. Under the sludge washing conditions, no desorption of sorbates was observed with MST; however, some additional sorption did occur. For CST, a small amount of Cs leached from the material during the first day of testing, but no further leaching was observed over the remaining test period. The final test was designed to examine the possibility of desorption from both MST and mMST upon increasing the solid to liquid phase ratio. The results of these tests indicated some desorption of Pu from MST within the first two weeks after changing the phase ratio, then resorption of some of the leached Pu over the remaining 4 weeks of the experiment. No desorption of any sorbates was observed for mMST under these conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Chemical interaction matrix between reagents in a Purex based process

The United States Department of Energy (DOE) is the responsible entity for the disposal of the United States excess weapons grade plutonium. DOE selected a PUREX-based process to convert plutonium to low-enriched mixed oxide fuel for use in commercial nuclear power plants. To initiate this process in the United States, a Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF) is under construction and will be operated by Shaw AREVA MOX Services at the Savannah River Site. This facility will be licensed and regulated by the U.S. Nuclear Regulatory Commission (NRC). A PUREX process, similar to the one used at La Hague, France, will purify plutonium feedstock through solvent extraction. MFFF employs two major process operations to manufacture MOX fuel assemblies: (1) the Aqueous Polishing (AP) process to remove gallium and other impurities from plutonium feedstock and (2) the MOX fuel fabrication process (MP), which processes the oxides into pellets and manufactures the MOX fuel assemblies. The AP process consists of three major steps, dissolution, purification, and conversion, and is the center of the primary chemical processing. A study of process hazards controls has been initiated that will provide knowledge and protection against the chemical risks associated from mixing of reagents over the life time of the process. This paper presents a comprehensive chemical interaction matrix evaluation for the reagents used in the PUREX-based process. Chemical interaction matrix supplements the process conditions by providing a checklist of any potential inadvertent chemical reactions that may take place. It also identifies the chemical compatibility/incompatibility of the reagents if mixed by failure of operations or equipment within the process itself or mixed inadvertently by a technician in the laboratories. (aut0010ho.

07 ISOTOPE AND RADIATION SOURCES↗

Fabrication of Al-Zn solid solution via friction stir processing

Highlights: • Thermomechanical nature of FSP was utilized for mechanical alloying. • Zn particles dissolved in Al during FSP to form solid solution. • Second pass of FSP lead to homogenization and partial decomposition of the solid solution. • Processed alloy exhibited improved hardness over base and FSPed metal. • The process can be adopted for site specific property enhancement. - Abstract: The present study demonstrates that friction stir processing (FSP) can be used as a mechanical alloying tool to process solid solution. Zn was incorporated in commercially pure aluminium by multi-pass FSP leading to its dissolution and formation of supersaturated solid solution which was confirmed by X-ray diffraction and scanning electron microscopy. The hardness across the stir zone matched with the distribution of Zn and was significantly improved compared to the base metal. The supersaturated solid solution that formed in the first pass, partially decomposed during the second pass, leading to the formation of fine Al-Zn precipitates. Thermal stability of the microstructure against abnormal grain growth was also improved after the second pass due to the pinning effect of the grain boundary precipitates. FSP also caused grain refinement of the alloy yielding fine equiaxed grains in the range of 4–6 μm with a high fraction (> 67%) of high angle grain boundaries. Such microstructure is conducive for isotropic properties and the fact that the microstructure is stable against thermal cycles make the process suitable for selective alloying for location specific property enhancement.

36 MATERIALS SCIENCE↗

Effect of Heat Treatment on Microstructure Evolution and Mechanical Properties of Selective Laser Melted Inconel 718 Alloy

The microstructure characteristics of the selective laser melted Inconel 718 alloy under as-deposited, homogenization + solution + aging (HSA) and solution + aging (SA) conditions were studied. The anisotropy and heterogeneity of mechanical properties under different conditions were also investigated. Under the as-deposited condition, the morphology and size of the grains are heterogeneous. The dendrite structures which grow nearly perpendicular to the molten pool traces, accompanying interdendritic Laves phase, can be observed within the grains. The dendrite structure completely disappeared, and the Laves phases embedded in the interdendritic regions also dissolved into the matrix to precipitate γ′ and γ″ phases after heat treatments. Fully recrystallized grains were obtained under the HSA condition, while only incomplete recrystallized grains were obtained under the SA condition. However, the characteristics of γ′ and γ″ phases are very similar under the HSA and SA conditions. Significant improvement in strength after heat treatments was due to the dissolution of undesirable Laves phase and the precipitation of γ′ and γ″ phases. For all the three conditions, different tensile properties were observed depending on the orientation of the specimens. The scatter of mechanical properties is notable, and heat treatments increased the scatter of mechanical properties.

36 MATERIALS SCIENCE↗

Fluid Induced Elemental and Mineralogy Alterations of Caney Shale

ABSTRACT: Studies were conducted on cores and rock cuttings recovered from two wells drilled in Caney shale in the Southern Oklahoma. Mineralogical compositions of these samples were obtained by X-Ray Diffraction (XRD) measurements using two methods of sample preparation: conventional powder (by crushing and grinding of rock fragments) and spray-drying of micronized rock powder method. Microstructure and microanalysis were acquired by Scanning Electron Microscopy/Energy Dispersive Spectroscopy (SEM/EDS). Batch experiments were then conducted using selected rock samples and fracturing fluid whilst deionized water was used as control sample for fluid/rock interaction. These were conducted at 95°C and ambient pressure for various time periods to assess the geochemical reactivity of the Caney shale. The rock samples were subsequently recovered from fluid, dried and analysis repeated using identical XRD and SEM/EDS measurements, following the same conditions. Preliminary experimental results show rock mineralogical compositions are predominantly quartz with relatively high clay content. The clay minerals are mainly illite. Carbonate content is less than 10% by weight for most samples, with other non-clay minerals pyrite, albite, dolomite, and some apatite. In general, sprayed samples showed more intense peaks and less full width at half maxima (FWHM) relative to conventional rock-powder samples. Post-experimental mineralogical changes were observed in samples with clay portions breaking down to amorphous entities. As expected, dissolution of carbonates (calcite and dolomite) was observed and newly detected dissolution of biogenic micro quartz resulted in formation of amorphous silica. 1.0 INTRODUCTION Formation of sedimentary rocks involves processes where rock sediments are emplaced with fluids starting interactions that persist over long periods. During the lithification process, sediments and fluids react and attain equilibrium state. This equilibrium is disturbed during drilling, completion, hydraulic fracturing and other operations that involve the introduction of engineered fluids into the subsurface. To return to equilibrium, dissolution and precipitation of minerals may occur. These reactions have implications on the petrophysical properties of the reservoir. Whiles dissolution and precipitation of minerals can enhance porosity and permeability, the reverse can also be true. For example, when acidic fluids are introduced into formations with high carbonate contents, carbonate minerals dissolve into solution thus increasing the porosity and permeability of the formation. In contrast, when alkaline fluids with pH above 11 are introduced into an illite-rich shale formation, the rock-fluid interaction leads to de-flocculation of illite platelets causing substantial increase in clay fines migration, consequently significant reduction in permeability (Salles et al., 2008).

Awejori, G.↗

Engineered Microorganisms for Enhanced Rare Earth Element Bio-mining and Separations (Final Technical Report)

Rare earth elements (REE) are critical ingredients of sustainable energy technologies, but their extraction from ore and separation from one another pose formidable challenges. To solve the challenge of REE supply, we used advanced genomics, high-throughput screening with synthetic REE minerals, and synthetic biology to engineer two sets of exotic microbes to (1) extract REE from ores, spent cracking catalysts, coal ash and electronic waste with high efficiency and selectivity, and (2) to purify REE into single element batches, all under benign conditions without the need of harsh solvents and high temperatures. This work integrated our expertise in systems and synthetic biology (Buz Barstow); rare-earth geochemistry (Esteban Gazel) and mineral synthesis (Megan Holycross); and microsystems engineering (Mingming Wu) by first elucidating the set of rules that predict an organism’s phenotype and then applying them to solve this critical problem in sustainable energy. These new technologies could help to revitalize the US rare earth industry and provide a new source of these critical elements for future energy technologies. We have already had some big success in tech transfer. Two of our team members (postdoctoral fellow Alexa Schmitz and graduate student Sean Medin) were able to study the supply chain for REE in the United States, and identify an opportunity to commercialize our REE mineral-dissolution technology. Alexa and Sean recently founded REEgen, Inc., an REE biomining company. Dr. Schmitz was recently awarded a fellowship from the Activate Foundation to support the first two years of REEgen. Cornell showed its support for this technology and company, and Dr. Schmitz was awarded the Rising Women Innovator’s award. These two awards unlocked support from Cornell’s Praxis Incubator.

58 GEOSCIENCES↗

Nanomineralogy as a new dimension in understanding elusive geochemical processes in soils: The case of low-solubility-index elements

Nanomineralogical studies of mineral surface coatings in soils reveal insights into biogeochemical processes that heretofore were not known to exist. This is a new dimension in understanding past and present biogeochemical processes in soils, and in this study it is a way to better understand the behavior of low-solubility-index elements such as Al, Ti, and Zr. Soils were sampled from selected sites in Sudbury (Ontario, Canada) that have been affected by acidification and particulate matter emissions from base-metal smelters with subsequent remediation within the past century. These anthropogenic processes have affected an entire landscape, but are now recorded in assemblages of nano-size phases that can be only studied using a combination of focused ion beam technology (for sample preparation) and high-resolution analytical transmission electron microscopy (for phase identification). A first generation of clay minerals (pre-acidification phase), their partial replacement by nano-size hematite and amorphous silica (anthropogenic acidification), and a second generation of clay minerals (post-acidification, including soil remediation) are products of changes in soil biogeochemical processes during these natural and anthropogenic-induced weathering stages. Furthermore, complex assemblages of nanophases formed prior to the second generation of clay minerals depict underlying mechanisms for the mobilization and sequestration of the low-solubility-index elements Zr and Ti under acidic conditions. The occurrence of baddeleyite (ZrO 2 ), anatase (TiO 2 ), and the Magneli phases Ti 4 O 7 and Ti 5 O 9 (all present at the nanoscale) suggest an influx of nanocolloidal Zr and Ti oxides during weathering of smelter-derived particulate matter. Kelyshite {NaZr[Si 2 O 6 (OH)]}, authigenic zircon (ZrSiO 4 ), and kleberite [Fe 3+ Ti 6 O 11 (OH) 5 ] are most likely products of the sequestration of the Zr- and Ti-bearing nanocolloids.

58 GEOSCIENCES↗

Martensitic Transformation of Close-Packed Polytypes of Block Copolymer Micelles

Here, we report martensitic shear transformation of strongly segregated block copolymer micelles on face-centered cubic (FCC) lattices to hexagonally close-packed (HCP) structures elucidated by X-ray scattering characterizations. The initial FCC crystal structures of the block copolymer micelles were prepared by direct dissolution of poly(1,2-butadiene-b-ethylene oxide) (PB-PEO) diblock copolymer in the water at 25 °C, and the FCC crystal domains were shear-aligned during the sample preparation process for the X-ray scattering measurements. Heating the shear-aligned FCC crystals of the PB-PEO micelles above 80 °C initiated the transformation to HCP structures, which are also found stable at 25 °C when cooled from the transition temperature. Interestingly, we found that the HCP crystal domains are also aligned, and this suggests that the FCC-to-HCP phase transition has occurred by the martensitic shear transformation. Scattering pattern analysis reveals that the martensitic shear transformation proceeds by preferentially dislocating a specific set of two-dimensional hexagonal close-packed (2D-HCP) layers among four equivalent 2D-HCP layers of the initially shear-aligned FCC crystals. We believe that the selective martensitic shear transformation originates from the orthorhombic-like morphology of the FCC crystal domains formed by slip dislocations and stratifications of initial FCC crystal grains during the sample preparation process. In the shear-aligned FCC crystals with the orthorhombic-like crystal domains, the specific 2D-HCP layers chosen for the martensitic shear transformation have the least area of dislocations, i.e., the least kinetic energy barrier, for the FCC-to-HCP phase transition and appear to be preferentially utilized. These results show that the size and morphology of crystal domains are critical to the formation, stability, and transformation of crystalline structures and consequently control the polymorphism of solid compounds.

36 MATERIALS SCIENCE↗

Preparation and Characterization of Chemical Plugs Based on Selected Hanford Waste Simulants

This report presents the results of preparation and characterization of chemical plugs based on selected Hanford Site waste simulants. Included are the results of chemical plug bench testing conducted in support of the M1/M6 Flow Loop Chemical Plugging/Unplugging Test (TP-RPP-WTP-495 Rev A). These results support the proposed plug simulants for the chemical plugging/ unplugging tests. Based on the available simulant data, a set of simulants was identified that would likely result in chemical plugs. The three types of chemical plugs that were generated and tested in this task consisted of: 1. Aluminum hydroxide (NAH), 2. Sodium aluminosilicate (NAS), and 3. Sodium aluminum phosphate (NAP). While both solvents, namely 2 molar (2 M) nitric acid (HNO3) and 2 M sodium hydroxide (NaOH) at 60°C, used in these tests were effective in dissolving the chemical plugs, the 2 M nitric acid was significantly more effective in dissolving the NAH and NAS plugs. The caustic was only slightly more effecting at dissolving the NAP plug. In the bench-scale dissolution tests, hot (60°C) 2 M nitric acid was the most effective solvent in that it completely dissolved both NAH and NAS chemical plugs much faster (1.5 – 2 x) than 2 M sodium hydroxide. So unless there are operational benefits for the use of caustic verses nitric acid, 2 M nitric acid heated to 60°C C should be the solvent of choice for dissolving these chemical plugs. Flow-loop testing was planned to identify a combination of parameters such as pressure, flush solution, composition, and temperature that would effectively dissolve and flush each type of chemical plug from preformed chemical plugs in 3-inch-diameter and 4-feet-long pipe sections. However, based on a review of the results of the bench-top tests and technical discussions, the Waste Treatment Plant (WTP) Research and Technology (R&T), Engineering and Mechanical Systems (EMS), and Operations concluded that flow-loop testing of the chemically plugged pipe sections would not provide any additional information or useful data. The decision was communicated through a Sub Contract Change Notice (SCN-070) that included a revised scope as follows: • Photographing the chemical plugs in the pipes before extrusion to compare the morphology of aged gels with that of fresh gels. • Setting up an extrusion apparatus and extruding the chemical plugs. • Documenting the qualitative observations on the efforts to remove the chemical plug materials from the pipe sections. • Performing X-ray diffraction (XRD) analysis of extruded gel samples to detect any crystallization of gel during storage. • Disposing of the extruded gel as a waste. • Documenting the analytical results in a test report. There were no significant morphological differences between the fresh and aged plugs except for an overgrowth of small transparent crystals on the surface of the aged NAS gel plug. An initial pressure of <150 psi was required to start extruding the aged NAS and NAP plugs, whereas the NAH plug began to extrude with the application of minimal pressure. The shear strength of extruded samples ranged from ~9 to >15 KPa for the NAS plug and from ~2 to 6 KPa for the NAH plug. Following extrusion, the NAP plug sections were thixotropic. The bulk of all the aged gel plugs consisted of amorphous material with nitratine constituting the crystalline phase. A separate question about the whether the current in-tank waste conditions will bound the future multi-tank blended feed conditions for the Waste Treatment Plant is outside the scope of this study.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Investigations regarding the wet decontamination of fluorescent lamp waste using iodine in potassium iodide solutions

Highlights: • A wet-based decontamination process for fluorescent lamp waste is proposed. • Mercury can be leached using iodine in potassium iodide solution. • The efficiency of the process increases with an increase in leachant concentration. • Selective leaching of mercury from rare earth elements is achieved. • Mercury is furthered recovered using ion exchange, reduction or solvent extraction. - Abstract: With the rising popularity of fluorescent lighting, simple and efficient methods for the decontamination of discarded lamps are needed. Due to their mercury content end-of-life fluorescent lamps are classified as hazardous waste, requiring special treatment for disposal. A simple wet-based decontamination process is required, especially for streams where thermal desorption, a commonly used but energy demanding method, cannot be applied. In this study the potential of a wet-based process using iodine in potassium iodide solution was studied for the recovery of mercury from fluorescent lamp waste. The influence of the leaching agent’s concentration and solid/liquid ratio on the decontamination efficiency was investigated. The leaching behaviour of mercury was studied over time, as well as its recovery from the obtained leachates by means of anion exchange, reduction, and solvent extraction. Dissolution of more than 90% of the contained mercury was achieved using 0.025/0.05 M I{sub 2}/KI solution at 21 °C for two hours. The efficiency of the process increased with an increase in leachant concentration. 97.3 ± 0.6% of the mercury contained was dissolved at 21 °C, in two hours, using a 0.25/0.5 M I{sub 2}/KI solution and a solid to liquid ratio of 10% w/v. Iodine and mercury can be efficiently removed from the leachates using Dowex 1X8 anion exchange resin or reducing agents such as sodium hydrosulphite, allowing the disposal of the obtained solution as non-hazardous industrial wastewater. The extractant CyMe{sub 4}BTBP showed good removal of mercury, with an extraction efficiency of 97.5 ± 0.7% being achieved in a single stage. Better removal of mercury was achieved in a single stage using the extractants Cyanex 302 and Cyanex 923 in kerosene, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Extraction of organic compounds from representative shales and the effect on porosity

This study is an attempt to understand how native organics are distributed with respect to pore size to determine the relationship between hydrocarbon chemistry and pore structure in shales, as the location and accessibility of hydrocarbons is key to understanding and improving the extractability of hydrocarbons in hydraulic fracturing. Selected shale cores from the Eagle Ford and Marcellus formations were subjected to pyrolysis gas chromatography (GC), thermogravimetric analysis, and organic solvent extraction with the resulting effluent analyzed by GC-mass spectrometry (MS). Organics representing the oil and gas fraction (0.1 to 1 wt. %) were observed by GC-MS. For most of the samples, the amount of native organic extracted directly related to the percentage of clay in the shale. The porosity and pore size distribution (0.95 nm to 1.35 m) in the Eagle Ford and Marcellus shales was measured before and after solvent extraction using small angle neutron scattering (SANS). An unconventional method was used to quantify the background from incoherent scattering as the Porod transformation obscures the Bragg peak from the clay minerals. Furthermore, the change in porosity from SANS is indicative of the extraction or breakdown of higher molecular weight bitumen with high C/H ratios (asphaltenes and resins). This is mostly likely attributed to complete dissolution or migration of asphaltenes and resins. These longer carbon chain lengths, C30-C40, were observed by pyrolysis GC, but either were too heavy to be analyzed in the extracts by GC-MS or were not effectively leached into the organic solvents. Thus, experimental limitations meant that the amount of extractable material could not be directly correlated to the changes in porosity measured by SANS. But, the observable porosity generally increased with solvent extraction. A decrease in porosity after extraction as observed in a shale with high clay content and low maturity was attributed to swelling of pores with solvent uptake or migration of resins and asphaltenes.

04 OIL SHALES AND TAR SANDS↗

Transmission electron microscopy examinations of metal-oxide interface of zirconium-based alloys irradiated in Halden reactor-IFA-638 - 2016-0039

This paper provides the results of investigations by transmission electron microscopy (TEM) on the selected materials from in-reactor oxidation tests in the Halden test reactor (Reference No. IFA-638) from 1998 to 2006. The objective of the IFA-638 test was to study the corrosion behavior of modern zirconium-based claddings to high burnup in pressurized water reactor water chemistry and thermal hydraulic conditions. The aim of this paper is to report on the microstructure of selected materials (ZIRLO{sup R}, E635, and Alloy A) after the irradiation to different burnup levels to determine the modifications induced by irradiation and to correlate results to their oxidation behavior. The TEM examinations revealed the nature of secondary phase particles (SPPs) and their modification under irradiation. Four types of SPPs were observed, namely β-niobium precipitates, Zr{sub 0.5}Nb{sub 0.3}Fe{sub 0.2} (mainly in the ZIRLO alloy), Zr(Fe,Nb){sub 2} (in E635), and (Cr,Fe){sub 2}Zr,Nb with varying niobium content (present in Alloy A: Zr-0.58Sn-0.31Nb-0.36Fe-0.26Cr). TEM observations showed that all three materials contained still several precipitates after irradiation and in the case of the ZIRLO alloy even after high burnups. Furthermore, the analysis of the metal side of the interface and its comparison with the oxide side led to the conclusion that all types of precipitates dissolved to some extent under irradiation and that their alloying element content decreased. The dissolution was intensified in the oxide. However, a more detailed examination showed that the β-niobium precipitates dissolved at a slower rate, or knowing that their composition was much richer in niobium, the time needed for the precipitates to become fully depleted from niobium was longer. Regarding the amorphization under irradiation, the b-niobium- and chromium-containing precipitates did not amorphize in the metal part of the interface. This was not the case for the other types of precipitates. Furthermore, these two types of SPP both showed delayed oxidation and due to this behavior the typical crack above the SPP in the oxide was also observed. These results are discussed to gain an improved understanding of the oxidation behavior of materials studied as a function of irradiation and residence time. (authors)

36 MATERIALS SCIENCE↗

Compatibility of Type 304H Stainless Steel in Static Molten FLiBe for Inertial Confinement Fusion Reactors: Role of Impurities and Redox Control

Molten fluoride salts, such as FLiBe (LiF-BeF2), are promising candidates for tritium breeding and heat transfer in fusion reactors, but corrosion of structural materials remains a major challenge. This study investigates the corrosion behavior of austenitic stainless steel 304H in purified and NiF2-containing FLiBe at 500°C and 600°C, focusing on the effects of impurities and redox control. Exposure to purified FLiBe resulted in the concurrent depletion of Cr, Mn, and Fe, with corrosion at 500 °C dominated by the combined oxide formation and elemental dissolution, while at 600°C elemental depletion was predominant. The addition of a controlled NiF2 impurity significantly accelerated corrosion at both temperatures, demonstrating the sensitivity of 304H to the salt redox state. Beryllium additions were effective in mitigating corrosion for both baseline and NiF2-containing FLiBe; minimal depletion of Cr, Mn, and Fe occurred with Be additions as low as 2.5 mg (147 wppm), and no NiBe intermetallics formed at 5 mg (294 wppm), indicating that small Be inventories can provide substantial protection without deleterious phase formation. Thermodynamic equilibrium and coupled thermodynamic-kinetic analyses at the salt-alloy interface suggested low corrosion rates in systems with limited hydrogen fluoride (HF) generation, highlighting the importance of salt redox control. Estimates for a Be addition rate were calculated for the HYLIFE-II fusion reactor that can mitigate corrosion-induced degradation, assuming complete conversion of tritium to tritium fluoride (TF). Overall, 304H shows reasonable compatibility with FLiBe under optimized redox conditions. These results provide quantitative guidance for material selection and salt management in fusion blanket and heat exchanger systems and motivate validation under flowing, nonisothermal, and irradiated conditions.

Pillai, Rishi [ORNL] (ORCID:0000000243688197)↗