Search NASA⌕ Search

SEARCH · Search NASA

Results for “α' precipitates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Grain-resolved temperature-dependent anisotropy in hexagonal Ti-7Al revealed by synchrotron X-ray diffraction

Hexagonal metals have anisotropic coefficients of thermal expansion causing grain-level internal stresses during heating. High energy x-ray diffraction microscopy, a non-destructive, in situ, micromechanical and microstructural characterization technique, has been used to determine the anisotropic coefficients of thermal expansion (CTEs) for Ti-7Al. Two samples of polycrystalline α-phase Ti-7Al were continuously heated from room temperature to 850 °C while far-field HEDM scans were collected. The results showed a change in the ratio of the CTEs in the ‘a’ and ‘c’ directions which explains discrepancies found in the literature. The CTE additionally appears to be affected by the dissolution of α 2 precipitates. Analysis of the grain-resolved micromechanical data also shows reconfiguration of the grain scale stresses likely due to anisotropic expansion driving crystallographic slip.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Coupled Small and Wide-Angle X-Ray Scattering Study of Phase Transformation Mechanisms in U-6Wt Pct Nb

The elevated temperature phase transformation kinetics of U-6wt%Nb in both wrought and cast conditions were investigated using in-situ high energy synchrotron X-ray scattering. The evolution of the phase content, γ-phase composition, and microstructure morphology was determined through the analysis of simultaneously collected wide-angle diffraction and small-angle scattering (SAXS) data. The results of the wide-angle scattering analysis, especially the phase fractions and average composition of the γ-phase, provide model parameters to enable a quantitative analysis using the SAXS data. Greater clarity regarding the kinetics of different precipitation mechanisms, namely the continuous precipitation (CP) of α-U within the γ-phase matrix and the discontinuous (DP) grain boundary precipitation of a lamellar microstructure, consisting of α-U and Nb-rich γ-phase are obtained from the coupled measurement modes. These results indicate that the CP mechanism is responsible for the initial precipitation of α-U at all temperatures considered. Near the nose in the time-temperature-transformation (TTT) diagram at ~798 K, both mechanisms are active during the early stages of phase transformation. However, the DP mechanism has an increasingly long incubation period with decreasing temperature below the TTT nose. In conclusion, the average interlamellar spacing obtained from the SAXS analysis increases with time, providing further evidence of the so-called divergent DP behavior previously observed in U-6wt%Nb alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural evolution of a silicon carbide-carbon coated nanostructured ferritic alloy composite during in-situ Kr ion irradiation at 300°C 450°C

This work focuses on irradiation behaviors of a novel silicon carbide and carbon coated nanostructured ferritic alloy (SiC-C@NFA) composite for potential applications as a cladding and structural material for next generation nuclear reactors. The SiC-C@NFA samples were irradiated with 1 MeV Kr ions up to 10 dpa at 300 and 450 °C. Microstructures and defect evolution were studied in-situ at the IVEM-Tandem facility at Argonne National Laboratory. The effects of ion irradiation on various phases such as α-ferrite matrix, (Fe,Cr) 7 C 3 , and (Ti,W)C precipitates were evaluated. The α-ferrite matrix showed a continuous increase in dislocation density along with spatial ordering of dislocation loops (or loop strings) at >5 dpa. The size of the dislocation loops at 450 °C was larger than that at 300 °C. The nucleation and growth of new (Ti,W)C precipitates in α-ferrite grains were enhanced with the ion dose at 450 °C. This study provides new insight into the irradiation resistance of the SiC-C@NFA system.

(FeCr)(7)C-3↗
DOE OSTI2020

Investigation of the relationship between classical and nonclassical ultrasound nonlinearity parameters and microstructural mechanisms in metals

This research studies two nonlinear ultrasound techniques: second harmonic generation and nonlinear resonant ultrasound spectroscopy, and the relationship to microstructural mechanisms in metals. The results show that there is a large change in both the classical, β, and nonclassical, α, ultrasound nonlinearity parameters in response to three specific microstructural mechanisms: precipitate growth in and along the grain boundaries, dislocations, and precipitate pinned dislocations. For example, both β and α increase with the growth of the precipitate radii (precipitate-pinned-dislocations). Additionally, both β and α increase when there is a growth of precipitates in and along the grain boundaries. As expected, β and α decrease when there is a removal of dislocations in the material. The relationship between β and α, and the microstructural mechanisms studied provide a quantitative understanding of the relationship between measured nonlinearity parameters and microstructural changes in metals, helping to demonstrate the possibility of using these two independent, but complementary, nonlinear ultrasound procedures to monitor microstructural damage.

Levy, Katherine Marie Scott↗
DOE OSTI2022

Numerical Study of Mineral Nucleation and Growth on a Substrate

We report nucleation and growth processes of minerals and other crystals can significantly affect one another due to the transport limitations and local depletion of reactive ions in the solution. Most numerical models and experimental measurements have typically focused on either growth or nucleation, but not both. In this work, we incorporate a heterogeneous nucleation process based on classical nucleation theory into a microcontinuum model that implements the Darcy–Brinkman–Stokes approach to study the interplay between nucleation and crystal growth on a substrate in diffusive systems. We demonstrate how the Damköhler number (reaction rate) and nucleation rate prefactor change the effective nucleation rate on a substrate. Higher surface growth rates deplete the solute concentration around the nuclei that appear initially on the substrate, creating islands that screen against further nucleation. The model predicts that measured nucleation rates may be affected by the history of crystal nucleation on the substrate. In the extreme case of high growth rates relative to diffusion, it predicts that the rate of subsequent nucleation is limited by reactant depletion. We introduce a nondimensional number α to represent the relation between surface propagation rate during growth and the heterogeneous nucleation rate. We show that it is important to control Damköhler number and α to achieve similar precipitation regimes at different reaction and nucleation rates. We suggest that the observed universality can guide the interpretation of experimental results on nucleation rates, since matching experiment can be achieved by tuning transport, reaction, and nucleation parameters simultaneously. In addition, we show how the bulk solution concentration affects the structure and topology of precipitation on a substrate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

A novel microstructural approach for TRIP/TWIP β-Ti alloys using intermetallic precipitation

Interest in metastable β-Ti has grown, due to the exceptional work hardening caused by TRansformation and TWinning Induced Plasticity (TRIP/TWIP). A current challenge is increasing the yield strength, while maintaining the benefits of TRIP/TWIP. This study presents the first report of TRIP/TWIP in a metastable β-Ti alloy containing intermetallic compounds, specifically Ti silicide precipitates. Silicon (Si) additions enable the formation of silicide particles, which can be precipitated, dissolved, and controlled through tailored heat treatments. In-situ synchrotron x-ray diffraction during tensile testing reveals primary {332}<113> twinning activates first, followed by TRIP, leading to extensive work hardening and uniform elongation in the solutionized state. In conclusion, these findings open a novel microstructural approach to the design of multiphase TRIP/TWIP titanium alloys, relying on intermetallic precipitation rather than allotropes such as α or ω phase, and lay the groundwork for future studies on intermetallic precipitation strengthening.

Materials science↗
DOE OSTI2021

Thermodynamic modeling of the Ti-Nb-Sn system and its preliminary applications in aging precipitation and solidification simulations

Abstract Gasping the thermodynamic and phase diagram of the materials being studied is essential for further guiding the development process, like composition design, heat treatment optimization and so on. Nb and Sn are common alloying elements in Ti-based biomedical alloys. In this work, the Ti-Nb-Sn system has been thermodynamically assessed based on experimental phase equilibria. A self-consistent thermodynamic description for the Ti-Nb-Sn system including two ternary compounds Ti 3 Nb 3 Sn 2 and Ti 3 NbSn has been obtained. Based on the comparison between the calculated and experimental phase equilibria, the reliability of the presently obtained thermodynamic description has been verified. The influence of Nb and Sn contents on the precipitation temperature and amount of hcp α -Ti phase in bcc β -(Ti, Nb) has been investigated based on thermodynamic calculations. Results show that the increase of Nb or Sn content in Ti-based alloys would significantly reduce the precipitation amount and transformation temperature of hcp α -Ti phase in bcc β -(Ti, Nb) and the influence of Nb content is more effective than that of Sn. The solidified phases in several as-cast alloys have been thermodynamically predicted based on Scheil solidification simulations. The presently developed thermodynamic description of the Ti-Nb-Sn system can serve as a sub-ternary one in the thermodynamic database for multicomponent Ti-based biomedical alloys.

Peng, Yingbiao↗
DOE OSTI2023

Progression of creep deformation from grain boundaries to grain interior in Al-Cu-Mn-Zr alloys

Creep mechanisms are studied in θ'-Al 2 Cu-strengthened Al-Cu-Mn-Zr alloys at 300 and 350°C for (i) ACMZ, a base alloy without further alloying elements and (ii) RR350, a commercial alloy with additions of Ni and Co forming distinct grain-boundary precipitates. At high stresses, creep is dominated by dislocations bypassing θ' precipitates within grains via the Orowan mechanism, as evidenced by (i) very high stress exponent (n~20-25) and (ii) α-Al and θ' lattice strains (measured via in-situ neutron diffraction) evolving during creep in a manner consistent with load transfer from the plastically-deforming α-Al matrix to elastically-deforming θ' precipitates. At intermediate stresses, both alloys exhibit a n~3 regime, where α-Al and θ' lattice strains scale near-linearly with applied stress while remaining largely unaffected by strain accumulation, indicating that Orowan looping or dislocation pile-up around θ' is now inactive within the grains. Rather, dislocation motion occurs solely in θ'-precipitate-free zones (θ'-PFZ) where high dislocation densities are observed via TEM after creep deformation. Plastic flow at θ'-PFZ and/or localized pipe diffusion are expected to enable grain-boundary sliding (GBS), which is proposed as the rate-limiting mechanism in the n~3 regime. Ni/Co-rich precipitates at RR350 grain-boundaries, with negligible θ'-PFZ around them, share load (as determined via neutron diffraction) with the α-Al matrix more effectively than θ-Al 2 Cu precipitates at ACMZ grain-boundaries, with wide surrounding θ'-PFZ. So, high creep resistance in the n~3 GBS regime of RR350 is enabled by coarsening-resistant grain-boundary precipitates, forming without concomitant development of weak θ'-PFZ, which effectively share load with the grains.

36 MATERIALS SCIENCE↗
DOE OSTI2025

TEM characterization of two variants of fuel cladding chemical interaction in a HT-9 Clad U-10Zr Fuel. Variant 1: FCCI with a Zr Rind

Here, this study investigated the fuel cladding chemical interaction (FCCI), a key factor that limits operational temperature and burnup, in an HT-9 clad U-10Zr nuclear fuel sample irradiated to a high burnup of 13.1 at.% at a time-averaged peak inner cladding temperature (PICT) of 530 °C. Previous results showed this fuel sample exhibited two distinct levels of FCCI at d. This paper analyzed the FCCI at an azimuthal position showing an interdiffusion layer of <10 µm using transmission electron microscopy to examine chemical and crystallographic nature of phases at the fuel-cladding interface at the nanoscale level. A ZrC layer and a Zr 3 Si phase were identified at the interface; these, along with the relatively low local temperature, potentially contributed to limit interdiffusion, behaving as inhibitors for deleterious interactions. Lanthanides (Ln) partially consumed the ZrC layer and interacted with Fe, forming a Zr-Ln compound and a (Zr,Ce)Fe 2+x phase while also infiltrating up to 4 µm into the cladding. Neither U nor Zr were observed in the cladding, whereas Fe diffused up to 3–5 µm in the fuel. Fe infiltration formed a ternary U-Zr-Fe ε-phase and likely promoted the precipitation of a Cr-rich α’ phase on the cladding interface. Additionally, a Cr-rich χ-phase, likely formed by the dissociation of pre-existing M 23 C 6 carbide precipitates, was identified about 2–5 µm from the fuel-cladding interface. Irradiation-induced nano-voids were also observed in the HT-9 bulk. These findings provide critical insights into FCCI mechanisms at representative irradiation conditions, essential for developing models simulating in-pile metallic fuel behaviors for next-generation reactors.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Irradiation Effects on Stability of δ-UZr2 phase in U-50 wt% Zr Alloy

U-50wt%Zr is a candidate metallic nuclear fuel with potential application in light water reactors due to its excellent thermal properties and high radiation tolerance. The Zr-rich UZr fuels possess greater swelling resistance and fission gas release characteristics compared with U-rich UZr fuels. In this current study, the δ-phase U-50wt%Zr is proton irradiated at room temperature to 1 displacement per atom (dpa) to provide insights on phase stability under irradiation conditions. High resolution characterization of Transmission Electron Microscopy (TEM) and Atom Probe Tomography (APT) characterization techniques are used to elucidate microstructural changes due to irradiation. TEM and APT results show highly oriented bcc β-Zr-rich platelet precipitates nucleating adjacent to α-U phases inside the UZr 2 matrix. Formation of this platelet morphology is characteristic of Widmänstatten structure which can be attributed to a variety of factors such as differences in thermal expansion coefficient between the phases, grain size, alloy composition, and cooling rate. The phases present are distinctly different than those observed through in situ annealing, but irradiation accelerates diffusion and phase separation kinetics. These microstructural changes in U-50wt%Zr are different from those achieved by pure thermodynamic or high temperature heavy ion irradiation experiments. Finally, our work, together with previous ones, highlight the necessity to study the U-Zr phase diagram under non-equilibrium thermodynamics conditions to support this material's deployment as a viable nuclear fuel form.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Thermo-Elastic Properties and Damping of U-6wt%Nb

While thermal expansion data exists for quenched (as well as aged) U-6wt%Nb, there is wide variation in the reported room temperature elastic moduli. To better understand the room temperature elastic behavior and to address the complete absence of data on the temperature dependence of the elastic moduli, room temperature and in-situ elevated temperature resonant ultrasonic spectroscopy (RUS) was performed along with x-ray diffraction (XRD) and dilatometry using a thermomechanical analyzer (TMA). An in-situ small- and wide-angle x-ray scattering (SAXS/WAXS) experiment was performed on a companion sample to help interpret the results. The room temperature polycrystalline dynamic moduli were measured to be E = 95.4 ± 4.5 GPa and G = 35.2 ± 0.2 GPa, respectively. As the temperature is raised, the stiffness slowly decreases, consistent with the empirical rule proposed by Varshni, up to the point of precipitation of the equilibrium α-U phase, which is stiffer than the martensitic phases. Homogenization theory of composites can be used to rationalize the observed response at high temperatures and after high-temperature exposures. Further, aging of the material at low temperatures (≤200°C) does not affect the linear elastic stiffness, but does impact the damping behavior which can be measured through RUS. This change in damping provides another perspective on the microstructure changes induced by low-temperature aging which also result in significant strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Flux effects in precipitation under irradiation simulation of Fe-Cr alloys

Radiation-enhanced precipitation of Cr-rich α’ in irradiated Fe-Cr alloys, which results in hardening and embrittlement, depends on the irradiating particle and the displacement per atom (dpa) rate. Here, we utilize a Cahn-Hilliard phase-field based approach, that includes simple models for nucleation, irradiating particle and rate dependent radiation-enhanced diffusion and cascade mixing to simulate α’ evolution under neutrons, heavy ions, and electron irradiations. Different irradiating particles manifest very different cascade mixing efficiencies. The model was calibrated using neutron data. For cascade inducing neutron/heavy-ion dpa rates at 300 °C between 10-8 and 10-6 dpa/s the model predicts approximately constant number density, decreasing radius, decreasing α’ Cr composition, and lower α’ volume fraction. The model then predicts a dramatic transition to no α’ formation above approximately 10-5 dpa/s, while electron irradiation, with weak mixing, had little effect at dpa rates up to 10-3 dpa/s. These model predictions are consistent with experiments. We explain the results in terms of the flux dependence of the radiation enhanced diffusion, cascade mixing, and their ratio, which all vary significantly in relevant flux ranges for neutron and cascade inducing ion irradiations. These results show that both cascade mixing and radiation enhanced diffusion must be accounted for when attempting to emulate neutron-irradiation effects using accelerated ion irradiations.

Ke, Jia-Hong↗
DOE OSTI2020

Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization

Selective Laser Melted Ti-6Al-4V (as-SLMed) exhibits decreased yield strength, increased work hardening, and increased ductility after heat treatment at 730 degrees C (HT-730) or 900 degrees C (HT-900) for 2 h. To understand the change of mechanical properties, in situ high energy X-ray diffraction (HEXRD) is used to examine the phase composition, load partitioning, slip system activity, and dislocation density evolution in all three specimens. The as-SLMed specimen is dominated by martensitic α'. After heat treatment, α' partly or fully decomposes into α+β, reducing the yield strength. In HT-730, beta precipitates with confined size show much higher lattice strain than the α'/α matrix during deformation; in HT-900, the lattice strain difference is mostly eliminated. This is a key reason for the increased ductility in HT-900. From the anisotropic lattice strain development, basal slip is identified as the easiest slip system in α'/α. Using an elasto-plastic self-consistent (EPSC) model, the critical resolved shear stress ratio between prismatic slip and basal slip (CRSS prism /CRSS basal ) is estimated to be 1.31 and 1.16 in the as -SLMed and the HT-900 specimens, respectively. Further, the alpha phase in HT-900 is able to activate multiple slip systems and accumulate more dislocations during plastic deformation. This explains why HT-900 has better ductility and higher work hardening rate than the other two specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural Changes and Chemical Analysis of Fission Products in Irradiated Uranium-7 wt.% Molybdenum Metallic Fuel Using Atom Probe Tomography

Understanding the microstructural and phase changes occurring during irradiation and their impact on metallic fuel behavior is integral to research and development of nuclear fuel programs. This paper reports systematic analysis of as-fabricated and irradiated low-enriched U-Mo (uranium-molybdenum metal alloy) fuel using atom probe tomography (APT). This study is carried out on U-7 wt.% Mo fuel particles coated with a ZrN layer contained within an Al matrix during irradiation. The dispersion fuel plates from which the fuel samples were extracted are irradiated at Belgian Nuclear Research Centre (SCK CEN) with burn-up of 52% and 66% in the framework of the SELENIUM (Surface Engineering of Low ENrIched Uranium-Molybdenum) project. The APT studies on U-Mo particles from as-fabricated fuel plates enriched to 19.8% revealed predominantly γ-phase U-Mo, along with a network of the cell boundary decorated with α-U, γ’-U2Mo, and UC precipitates along the grain boundaries. The corresponding APT characterization of irradiated fuel samples showed formation of fission gas bubbles enriched with solid fission products. The intermediate burnup sample showed a uniform distribution of the typical bubble superlattice with a radius of 2 nm arranged in a regular lattice, while the high burnup sample showed a non-uniform distribution of bubbles in grain-refined regions. There was no evidence of remnant α-U, γ’-U2Mo, and UC phases in the irradiated U-7 wt.% Mo samples.

Bachhav, Mukesh↗
DOE OSTI2026

Microstructural evolution, defect mitigation, and precipitation behavior in AA6061 via laser powder bed fusion with high-temperature substrate heating

Defects, particularly solidification cracking, remain persistent challenges in the laser powder bed fusion (LPBF) processing of AA6061 aluminum alloy. This study systematically investigates defect mitigation, microstructural evolution, and mechanical properties associated with high-temperature substrate preheating at 500 °C. Comprehensive microstructural analyses, including characterization of defects, grain structures, and precipitation behavior, were performed on samples in both as-built and T6 heat-treated states. Elevated preheating substantially reduced solidification cracking across a wide processing window, while demonstrating decreased crack sensitivity to laser parameters. Columnar cracks along the build direction were observed despite substrate preheating. Lack-of-fusion and keyhole porosity were effectively eliminated, though gas-induced microporosity persisted at higher powers. In-depth characterization of two distinct laser power and speed conditions confirmed the formation of micron-sized, non-coherent Mg 2 Si precipitates under heated substrate conditions, alongside α-AlFeCrMnSi intermetallic phases indicative of in-situ thermal effects during fabrication. Subsequent T6 heat treatment revealed the formation of fine, coherent needle-shaped β″ strengthening precipitates. Despite substantial differences in processing parameters, comparable mechanical properties were measured in the as-built samples (∼52 MPa yield strength, ∼130 MPa tensile strength), primarily due to reduced strain hardening effects and consistent precipitation characteristics. Meanwhile, the T6 heat treatment led to significant improvement in properties, enhancing yield strength by over 400%, aligning closely with the performance of conventional wrought AA6061-T6. These findings underscore that high-temperature substrate preheating offers an effective means to suppress cracks, control precipitation, and enhance mechanical performance in LPBF-processed AA6061.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Probing elemental speciation in hydrochar produced from hydrothermal liquefaction of anaerobic digestates using quantitative X-ray diffraction

Valorization of hydrochar, a solid byproduct from hydrothermal liquefaction (HTL) of anaerobically-digested agriculture wastes (digestates), requires fundamental knowledge of elemental speciation. This study investigated the effects of reaction temperatures (320–360 °C), digestate pH (3.5–8), and digestate cellulose-to-lignin ratios (0.2–1.8) on the speciation (chemical form) and composition of organics and inorganics in hydrochars produced during hydrothermal treatment. Quantitative X-ray diffraction (XRD) method was the primary technique used to characterize hydrochars. The comprehensive XRD pattern processing including the Rietveld refinement protocols demonstrated that the organic phase was comprised of mostly crystalline monocyclic, heterocyclic, and polycyclic aromatics with diverse aliphatic and aromatic substituents, while the inorganic mineral phase consisted of calcium-phosphates, magnesium-phosphates, calcium-carbonates, and magnesium-carbonates. Further, XRD results were validated by the elemental yields of products and the distribution of chemical functionalities measured using solid-state nuclear magnetic resonance (NMR) spectroscopy. The characterization data were used to evaluate proposed mechanistic pathways using compositional analysis of biocrude and aqueous-phase coproducts. Mechanistic pathways developed in the study suggested that benzoic acids, phenols, benzaldehydes, phenolic aldehydes, α-dicarbonyls, and α-hydroxycarbonyls were responsible for the precipitation of organics through various reactions depending on operating conditions. Meanwhile, the formation of inorganic compounds appeared to be consistently represented by reactions including dehydration, hydrolysis, endergonic reduction, and structure rearrangement of native minerals in the digestates. This study provides basic knowledge needed to create and assess potential elemental speciation pathways. In addition, the results of the study facilitate the specification of process conditions to optimize targeted utilization routes of hydrochar for more economically-feasible and sustainable HTL processing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Influence of soluble oligomeric aluminum on precipitation in the Al-KOH-H2O system

The role of oligomeric aluminate (Al(OH)4-) species in the precipitation of aluminum phases such as gibbsite (a-Al(OH)3) from aqueous hydroxide solutions remains unclear and difficult to probe directly, despite its importance to developing accurate predictions of Al solubility in highly alkaline systems. Precipitation in this system entails a transition from predominantly tetrahedrally coordinated Al species in solution to octahedrally coordinated Al in gibbsite. Here we report a quantitative study of dissolved Al in the Al-KOH-H2O system using a combination of molecular spectroscopies. We established a relationship between changes in 27Al NMR chemical shifts and the relative intensity of Raman vibrational bands, indicative of variations in the ensemble speciation of Al in solution, and the formation of unique contact ion pair interactions with the aluminate dimer, Al2O(OH)62 . A strong correlation between the extent of Al oligomerization and the amount of solvated Al was demonstrated by systematically varying the KOH:Al molar ratio. The concentration of dissolved oligomeric Al in solution also directly impacted the particle size and morphology of gibbsite; high concentrations of dimeric Al2O(OH)62-, yielded smaller and more numerous anhedral to subhedral gibbsite particles, while low concentrations yielded fewer and larger euhedral gibbsite platelets. The collective observations suggest a key role of the Al2O(OH)62- dimer in promoting gibbsite precipitation from solution, where the potassium ion-paired dimer possibly catalyzes a more rapid transformation of Al coordination from tetrahedral in solution to octahedral in gibbsite.

Dembowski, Mateusz↗
DOE OSTI2024

Photosynthetic responses of switchgrass to light and CO 2 under different precipitation treatments

Switchgrass ( Panicum virgatum L .) is a prominent bioenergy crop with robust resilience to environmental stresses. However, our knowledge regarding how precipitation changes affect switchgrass photosynthesis and its responses to light and CO 2 remains limited. To address this knowledge gap, we conducted a field precipitation experiment with five different treatments, including −50%, −33%, 0%, +33%, and +50% of ambient precipitation. To determine the responses of leaf photosynthesis to CO 2 concentration and light, we measured leaf net photosynthesis of switchgrass under different CO 2 concentrations and light levels in 2020 and 2021 for each of the five precipitation treatments. We first evaluated four light and CO 2 response models (i.e., rectangular hyperbola model, nonrectangular hyperbola model, exponential model, and the modified rectangular hyperbola model) using the measurements in the ambient precipitation treatment. Based on the fitting criteria, we selected the nonrectangular hyperbola model as the optimal model and applied it to all precipitation treatments, and estimated model parameters. Overall, the model fit field measurements well for the light and CO 2 response curves. Precipitation change did not influence the maximum net photosynthetic rate ( P max ) but influenced other model parameters including quantum yield ( α ), convexity ( θ ), dark respiration ( Rd ), light compensation point ( LCP ), and saturated light point ( LSP ). Specifically, the mean P max of five precipitation treatments was 17.6 μmol CO 2 m −2 s −1 , and the ambient treatment tended to have a higher P max . The +33% treatment had the highest α , and the ambient treatment had lower θ and LCP , higher Rd , and relatively lower LSP . Furthermore, precipitation significantly influenced all model parameters of CO 2 response. The ambient treatment had the highest P max , largest α , and lowest θ , R d , and CO 2 compensation point LCP . Overall, this study improved our understanding of how switchgrass leaf photosynthesis responds to diverse environmental factors, providing valuable insights for accurately modeling switchgrass ecophysiology and productivity.

09 BIOMASS FUELS↗