Search NASA⌕ Search

SEARCH · Search NASA

Results for “CLOSE PACKED STRUCTURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

In situ investigation of the deformation behaviors of Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys by high-energy X-ray diffraction

In situ synchrotron-based high-energy X-ray diffraction (HE-XRD) technique was employed to investigate the mechanical behaviors and microstructural evolution of face-centered cubic (FCC) Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys (HEAs) during tensile deformation. Fe 20 Co 30 Cr 30 Ni 20 HEA has a good combination of strength (ultimate tensile strength of 864 ± 35 MPa) and ductility (elongation of 0.627 ± 0.021). The HE-XRD investigation reveals that Fe 20 Co 30 Cr 30 Ni 20 HEA has the transformation-induced plasticity (TRIP) effect, which starts at a critical stress of ~555 MPa. Furthermore, transmission electron microscopy confirmed this deformation-induced new phase is hexagonal-close-packed structured ε-martensite, which follows an orientation relationship of {111} γ //(0001) ε , and (110) γ //[11 2 ¯ 0] ε with the FCC γ matrix. The observation of deformation twins in the deformed samples of the two studied HEAs proves that twinning-induced plasticity (TWIP) effect occurs in both HEAs. The combination of TRIP and TWIP effects lead to the high strength, large ductility and improved strain hardening behavior of Fe 20 Co 30 Cr 30 Ni 20 HEA.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Melting line and thermal equation of state of fcc-cobalt: A combined experimental and computational approach

The melting line of cobalt has been investigated both experimentally, using synchrotron X-ray diffraction coupled with laser-heated diamond anvil cells, and theoretically, using ab initio simulations. Over the investigated pressure and temperature range – between 30 and 100 GPa and from ambient temperature up to 4000 K – the hexagonal close-packed structure, stable at ambient conditions, is replaced at high temperature by the face-centered cubic structure, observed stable till melting. The melting temperatures obtained by the two methods are in remarkable agreement and the melting line can be well described by a Simon–Glatzel equation of the form T$_m$ = 1768(K)(P(GPa)/35.62+1) 0.64 . Finally, from the obtained results it was possible to determine a thermal equation of state for the cubic face-centered phase of Co.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Fundamental Thermodynamic, Kinetic, and Mechanical Properties of Lithium and Its Alloys

Lithium alloying reactions are beneficial in promoting uniform plating and stripping of lithium metal in all-solid-state batteries. First-principles calculations are performed to predict thermodynamic, kinetic, and mechanical properties of lithium and several important Li–M alloys (M = Mg, Ag, Zn, Al, Ga, In, Sn, Sb, and Bi). While the Li–Mg binary system forms a solid solution, most other lithium–metal alloys prefer stoichiometric intermetallic compounds with common local motifs that enable fast Li diffusion. Lithium and Li-rich alloys exhibit an unusually flat energy landscape along paths that connect BCC to close-packed structures like FCC and HCP, with important implications for mechanical properties. Very low migration barriers for Li diffusion that rival those of superion conductors are predicted, both in pure Li and in Li–M intermetallics. However, vacancy concentration, which is crucial for substitutional diffusion, is predicted to be low in metallic Li and most Li–M intermetallics. Compounds such as B32 LiAl and LiGa as well as D0 3 Li 3 Sb and Li 3 Bi exhibit structural vacancies at higher ends of their voltage windows, which together with low migration barriers leads to exceptionally high Li mobilities. In the Li–Mg solid solution, the addition of Mg is found to decrease the vacancy tracer diffusion coefficient by an order of magnitude.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Effects of Temperature on the Assembly of Gold Nanoparticle by Interpolymer Complexation

Using synchrotron-based small-angle X-ray scattering techniques, we demonstrate that poly(ethylene glycol)-functionalized gold nanoparticles (PEG-AuNPs) are assembled into close-packed structures that include short-range order with face-centered cubic structure, where crystalline qualities are varied by controlling the electrolyte concentration, pH, and temperature of the suspensions. Here, we show that interpolymer complexation with poly(acrylic acid) (PAA) is induced by lowering the pH level of the PEG-AuNPs suspensions, and furthermore, increasing the temperature of the suspension strengthens interparticle attraction, leading to improved supercrystal structures. Our results indicate that this strategy creates robust nanoparticle superlattices with high thermal stability. The effects of PAA and PEG chain lengths on the assemblies are also investigated, and their optimal conditions for creating improved superlattices are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Impact of peripheral alkyl chain length on mesocrystal assemblies of G2 dendrons

Unique sphere-packing mesophases such as Frank–Kasper (FK) phases have emerged from the viable design of intermolecular interactions in supramolecular assemblies. In this work, a series of C n -G2-CONH 2 dendrons possessing an identical core wedge are investigated to elucidate the impact of peripheral alkyl chain lengths (C n ) on the formation of the close-packed structures. The C 18 and C 14 dendrons, of which the contour lengths of the periphery L p are longer than the wedge length L w , assemble into a uniform sphere-packing phase such as body-centred cubic (BCC), whereas the C 8 dendron with short (L p < L w ) corona environment forms the FK A15 phase. Particularly in the intermediate C 12 and C 10 dendrons (L p ≈ L w ), cooling the samples from an isotropic state leads to cooling-rate-dependent phase behaviours. The C 12 dendron produces two structures of hexagonal columnar and sphere-packing phases (BCC and A15), while the C 10 dendron generates the A15 and σ phases by the fast- and slow-cooling processes, respectively. Our results show the impact of peripheral alkyl chain lengths on the formation of mesocrystal phases, where the energy landscape of the dendrons at L p /L w ≈ 1 must be more complex and delicate than those with either longer or shorter peripheral alkyl chains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Cryogenic temperatures promote the pressure-induced polymorphic transition in CoCrFeMnNi high entropy alloy

Pressure-induced polymorphism has recently been demonstrated in several high entropy alloys. This offers a new window into the much-debated issue of phase selection and stability in these systems. Here, we examine the effect of cryogenic temperatures on the pressure-induced transition from face centered cubic to hexagonal close-packed structures of the prototype CoCrFeMnNi (Cantor) alloy. We observe a reduction in the critical pressure for the onset of the polymorphic transition as the temperature decreases, confirming the progressive stabilization of the hexagonal phase with decreasing temperature previously predicted by ab initio calculations accounting for magnetic interactions. We argue that in situ high-pressure experiments at cryogenic temperatures, which suppress time-dependent transformation triggered at higher temperatures, present a unique opportunity to significantly improve our understanding of these complex alloys.

alloys↗
NASA NTRS1985

Processing of laser formed SiC powder

Superior SiC characteristics can be achieved through the use of ideal constituent powders and careful post-synthesis processing steps. High purity SiC powders of approx. 1000 A uniform diameter, nonagglomerated and spherical were produced. This required major revision of the particle formation and growth model from one based on classical nucleation and growth to one based on collision and coalescence of Si particles followed by their carburization. Dispersions based on pure organic solvents as well as steric stabilization were investigated. Although stable dispersions were formed by both, subsequent part fabrication emphasized the pure solvents since fewer problems with drying and residuals of the high purity particles were anticipated. Test parts were made by the colloidal pressing technique; both liquid filtration and consolidation (rearrangement) stages were modeled. Green densities corresponding to a random close packed structure (approx. 63%) were achieved; this highly perfect structure has a high, uniform coordination number (greater than 11) approaching the quality of an ordered structure without introducing domain boundary effects. After drying, parts were densified at temperatures ranging from 1800 to 2100 C. Optimum densification temperatures will probably be in the 1900 to 2000 C range based on these preliminary results which showed that 2050 C samples had experienced substantial grain growth. Although overfired, the 2050 C samples exhibited excellent mechanical properties. Biaxial tensile strengths up to 714 MPa and Vickers hardness values of 2430 kg/sq mm 2 were both more typical of hot pressed than sintered SiC. Both result from the absence of large defects and the confinement of residual porosity (less than 2.5%) to small diameter, uniformly distributed pores.

Haggerty, J. S.↗
NASA NTRS1987

Processing of laser formed SiC powder

Processing research was undertaken to demonstrate that superior SiC characteristics could be achieved through the use of ideal constituent powders and careful post-synthesis processing steps. Initial research developed the means to produce approximately 1000 A uniform diameter, nonagglomerated, spherical, high purity SiC powders. Accomplishing this goal required major revision of the particle formation and growth model from one based on classical nucleation and growth to one based on collision and coalescence of Si particles followed by their carburization. Dispersions based on pure organic solvents as well as steric stabilization were investigated. Test parts were made by the colloidal pressing technique; both liquid filtration and consolidation (rearrangement) stages were modeled. Green densities corresponding to a random close packed structure were achieved. After drying, parts were densified at temperatures ranging from 1800 to 2100 C. This research program accomplished all of its major objectives. Superior microstructures and properties were attained by using powders having ideal characteristics and special post-synthesis processing procedures.

Haggerty, J. S.↗
NASA NTRS1991

Atomic force microscope studies of fullerene films - Highly stable C60 fcc (311) free surfaces

Atomic force microscopy and X-ray diffractometry were used to study 1500 A-thick films of pure C60 grown by sublimation in ultrahigh vacuum onto a CaF2 (111) substrte. Topographs of the films did not reveal the expected close-packed structures, but they showed instead large regions that correspond to a face-centered cubic (311) surface and distortions of this surface. The open (311) structure may have a relatively low free energy because the low packing density contributes to a high entropy of the exposed surface.

Snyder, Eric J.↗
NASA NTRS2020

Core Losses in Co-Rich Inductors with Tunable Permeability

High frequency, low loss power systems enable electrified aircraft propulsion. Filter inductors that reduce noise in high current systems can account for 50% of the motor drive mass. Efficient inductor cores with tunable permeability reduce system mass by producing less heat, that removes heat sink mass. Requirements for filter inductors vary based on the chosen topology, but all inductor cores must operate below saturation levels. As the saturation flux density is limited (less than ~2 T), high differential current applications require cores with low relative permeabilities. The large induced anisotropies possible in Co-rich metal amorphous nanocomposite materials enables gapless inductors with relative permeabilities down to ~20. These materials have fine grain size ~8nm with a faulted, close packed structure. The impact of different processing methods on core losses are presented along with comparison to other low permeability soft magnetic materials.

Leary, Alex↗
DOE OSTI2021

Asymmetric equilibrium core structures of pyramidal-II < c + a > dislocations in ten hexagonal-close-packed metals

The structures of pyramidal-II < c + a > dislocations, one of the most important defects in structural hexagonal-close-packed (HCP) metals, have not been fully characterized for many of the HCP metals in use today. Here, we employ ab initio informed phase-field dislocation dynamics to determine the minimum energy structure of pyramidal {1¯1¯22} < 11¯23 > dislocations in ten HCP metals, including Be, Co, Mg, Re, Ti, Zn, Cd, Hf, Y, and Zr. As input for the simulations, we calculate, using first-principles density functional theory, the {1¯1¯22} generalized stacking fault energy (GSFE) curves for all ten metals. From these calculations, it is found that magnetism in Co is necessary for achieving a local minimum in the GSFE curve. We observe in simulations that edge and screw character dislocations split into two partials separated by a low-energy intrinsic stacking fault. The splitting distance is shown to scale inversely with the local minimum energy normalized by the product of its shear modulus and Burgers vector. Interestingly, some HCP metals exhibit an asymmetric structure, with either unequal partial Burgers vectors or widths, in contrast to the symmetric configuration expected from linear elastic dislocation theory. We explain these structures by properties of the local maxima in their GSFE curves. Metals with larger degrees of elastic anisotropy result in dislocations with larger splitting distances than would be expected under the commonly used assumption of elastic isotropy. Furthermore, these findings on the sizes and asymmetry in the structures of pyramidal-II < c + a > dislocations are fundamental to understanding how these dislocations glide and interact or react with other defects when these metals are mechanically strained.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structures of elemental potassium at terapascal pressures

Here we investigate the pressure-temperature phase diagram of elemental potassium (K) up to multiterapascal (TPa) pressures using ab initio random structure searching (AIRSS), discovering eight structural phase transitions beyond the already known double hexagonal close-packed (dhcp) structure. Starting at 1.15 TPa, K transitions from the dhcp structure and passes through a variety of close-packed hexagonal and trigonal phases (dhcp → P6 3 /mmc → P3m1 → P$\bar{6}m2$), which differ only in their stacking sequence along the c axis. At 2.55 TPa, K adopts the hexagonal close-packed (hcp) structure, and at 7.21 TPa transitions into a complex orthorhombic phase of Fddd symmetry with 64 atoms in its (conventional) unit cell, before assuming an Ibam structure at 8.60 TPa, and, eventually, the face centered cubic (fcc) structure at 23.6 TPa, which persists well into the petapascal (PPa) regime. Further, we calculate the full pressure-temperature dependence of the melting line of K through extensive molecular dynamics simulations. We study the evolution of the bonding topology of K with pressure, finding that K passes through two quasi-molecular phases featuring diatomic pairs (the Fddd and Ibam structures), before ultimately becoming a high pressure electride (HPE) in the fcc phase. The electron-phonon and superconducting properties of K at these extreme pressures are also investigated, where we find the critical temperature T c rises to a maximum of between 7.65 K and 15.70 K in the hcp phase, before eventually decreasing to essentially zero in the fcc phase. Our results fully elucidate the structural and electronic behavior of K under the most extreme conditions, and provide new case studies for multi-TPa dynamic compression experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Ultrahigh-pressure crystallographic passage towards metallic hydrogen

The structural evolution of molecular hydrogen H 2 under multi-megabar compression and its relation to atomic metallic hydrogen is a key unsolved problem in condensed-matter physics. Although dozens of crystal structures have been proposed by theory, only one, the simple hexagonal-close-packed (hcp) structure of only spherical disordered H 2 , has been previously confirmed in experiments. Through advancing nano-focused synchrotron X-ray probes, here we report the observation of the transition from hcp H 2 to a post-hcp structure with a six-fold larger supercell at pressures above 212 GPa, indicating the change of spherical H 2 to various ordered configurations. Theoretical calculations based on our XRD results found a time-averaged structure model in the space group $P\bar{6}2c$ with alternating layers of spherically disordered H 2 and new graphene-like layers consisting of H 2 trimers (H 6 ) formed by the association of three H 2 molecules. Here, this supercell has not been reported by any previous theoretical study for the post-hcp phase, but is close to a number of theoretical models with mixed-layer structures. The evidence of a structural transition beyond hcp establishes the trend of H 2 molecular association towards polymerization at extreme pressures, giving clues about the nature of the molecular-to-atomic transition of metallic hydrogen. Considering the spectroscopic behaviours that show strong vibrational and bending peaks of H 2 up to 400 GPa, it would be prudent to speculate the continuation of hydrogen molecular polymerization up to its metallization.

Ji, Cheng [Center for High Pressure Science and Te↗
NASA NTRS1986

Stability and structure of metal clusters - Be(13) and Be(55)

Face-centered cubic (fcc) and hexagonally close-packed (hcp) structures are compared for Be(13) and Be(55) clusters. Both Be(13) and Be(55) prefer the fcc structure over the bulk hcp structure, but the energy difference per atom decreases for Be(55) relative to Be(13). The binding energy per atom, 1.3 eV for Be(55) and 0.8-0.9 eV for Be(13), reflects the greater total number of bonds in the larger cluster rather than a difference in bonding. The energies per bond are much more similar, in the range of 0.30-0.34 eV for both clusters. The size of the p-basis set used influences both stability and ionization potentials strongly.

Pettersson, Lars G. M.↗
DOE OSTI2023

Chemical interactions that govern the structures of metals

Most metals adopt simple structures such as body-centered cubic (BCC), face-centered cubic (FCC), and hexagonal close-packed (HCP) structures in specific groupings across the periodic table, and many undergo transitions to surprisingly complex structures on compression, not expected from conventional free-electron-based theories of metals. First-principles calculations have been able to reproduce many observed structures and transitions, but a unified, predictive theory that underlies this behavior is not yet in hand. Discovered by analyzing the electronic properties of metals in various lattices over a broad range of sizes and geometries, a remarkably simple theory shows that the stability of metal structures is governed by electrons occupying local interstitial orbitals and their strong chemical interactions. The theory provides a basis for understanding and predicting structures in solid compounds and alloys over a broad range of conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRSDate not supplied

Energy landscape in Ni-Co-Cr and related alloys

Among multi-principal element alloys, the NiCoCr middle-entropy alloy has an outstanding combination of strength and ductility at both low and elevated temperatures. Equiatomic NiCoCr is a single-phase alloy with the face centered cubic (fcc) crystal structure. A low stacking fault energy in the fcc matrix is a cause of a relatively low creep in this alloy. The hexagonal close-packed (hcp) structure differs from the fcc by a stacking of atomic layers. The energy difference between the hcp and fcc structures is known to correlate with the stacking fault energy in the fcc phase. We compute formation and relative structural energies versus composition in the Ni-Co-Cr ternary and related quaternary systems, discuss possibilities of compositional adjustments, and compare theoretical predictions with experiment. We acknowledge funding by NASA’s Aeronautics Research Mission Directorate (ARMD) via Transformational Tools and Technologies (TTT) Project.

NiCoCr↗
NASA NTRSDate not supplied

Energy landscape in Ni-Co-Cr and related alloys

Among multi-principal element alloys, the NiCoCr middle-entropy alloy has an outstanding combination of strength and ductility at both low and elevated temperatures. Equiatomic NiCoCr is a single-phase alloy with the face centered cubic (fcc) crystal structure. A low stacking fault energy in the fcc matrix is a cause of a relatively low creep in this alloy. The hexagonal close-packed (hcp) structure differs from the fcc by a stacking of atomic layers. The energy difference between the hcp and fcc structures is known to correlate with the stacking fault energy in the fcc phase. We compute formation and relative structural energies versus composition in the Ni-Co-Cr ternary and related quaternary systems, discuss possibilities of compositional adjustments, and compare theoretical predictions with experiment. We acknowledge funding by NASA’s Aeronautics Research Mission Directorate (ARMD) via Transformational Tools and Technologies (TTT) Project.

Multiscale↗