Understanding the Interplay Between CdSe Thickness and Cu Doping Temperature in CdSe/CdTe Devices
Not provided.
Energy & Fuels↗
SEARCH · Search NASA
Results for “Cu in CdTe”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low-temperature and effective ex situ group V doping for efficient polycrystalline CdSeTe solar cells
CdTe solar cell technology is one of the lowest-cost methods of generating electricity in the solar industry, benefiting from fast CdTe absorber deposition, CdCl 2 treatment and Cu doping. However, Cu doping has low photovoltage and issues with instability. Doping group V elements into CdTe is therefore a promising route to address these challenges. Although high-temperature in situ group V doped CdSeTe devices have demonstrated efficiencies exceeding 20%, they face obstacles including post-deposition doping activation processes, short carrier lifetimes and low activation ratios. Here, we demonstrate low-temperature and effective ex situ group V doping for CdSeTe solar cells using group V chlorides. For AsCl 3 doped CdSeTe solar cells, the dopant activation ratio can be 5.88%, hole densities reach >2 × 10 15 cm -3 and carrier lifetime is longer than 20 ns. Thus, ex situ As doped CdSeTe solar cells show open-circuit voltages ~863 mV, compared to the highest open-circuit voltage of 852 mV for Cu doped CdSeTe solar cells.
14 SOLAR ENERGY↗
Point defects in CdTe and CdSeTe alloy: a first principles investigation with DFT+U
CdTe and its alloy CdSeTe are widely used in optoelectronic devices, such as radiation detectors and solar cells, due to their superior electrical properties. However, the formation of defects and defect complexes in these materials can significantly affect their performance. As a result, understanding the defect formation and recombination processes in CdTe and CdSeTe alloy is of great importance. In recent years, density functional theory (DFT) calculations have emerged as a powerful tool for investigating the properties of defects in semiconductors. In this paper, we use DFT+U calculations to comprehensively study the properties of intrinsic defects as well as extrinsic defects induced by commonly used dopants, such as Cu and group V elements, in CdTe and CdSeTe alloy. This work provides insights into the effects of these defects on the electrical and optical properties of the material.
14 SOLAR ENERGY↗
Investigating Local Carrier Dynamics in PERC Patterned CdTe Solar Cells
Remarkable progress has been achieved in CdTe photovoltaics (PVs) to further improve cell performance while reducing manufacturing costs. Researchers optimized the front contact that leads the short-circuit current density (J sc ) over 31mA/cm 2 (e.g., (Zn, Mg)O buffer layer and/or alloying CdTe with Se). Reese et al. reported an open-circuit voltage (V oc ) over 1 V with group-V doped single crystal, showing the feasibility of increasing V oc in CdTe PV that is fixed to less than 900 mV in most cases. Recent studies suggested that the V oc improvement in polycrystalline CdTe PVs requires well-passivated back contact. One possible strategy is to use CdMgTe alloy (E g > 1.8 eV), where the band-gap offset (ΔE CB ≈ 0.2 eV) reflects minority carrier electrons, thereby decreasing surface recombination. Another strategy is to utilize a stable Al 2 O 3 layer as an electron reflector; experimental works confirmed the improved performance with a conformal Al 2 O 3 layer. In this configuration, the precise control of Al 2 O 3 (≈1 nm) over the entire CdTe layer is essential because the J sc greatly depends on the tunneling current. While promising, both CdMgTe and Al 2 O 3 passivation on CdTe introduce unfavorable valence band offset that blocks the hole transport. Kephart et al. proposed a patterned passixc vation layer (≈ 20 nm Al 2 O 3 ) with point contacts (≈ 3 μm in diameter) that extract hole carriers. This configuration is similar to the passive emitter and rear contact (PERC) design that has been extensively studied in Si PVs. While remarkably high carrier lifetime and photoluminescence (> 10 X) were measured, consistent improvement in V oc and efficiency in this CdTe PERC were not yet observed. At this time, it is unclear how the surface potential is distributed in the presence of patterned Al 2 O 3 reflectors and how this additional field impacts the PV performance for Cu-doped and group-V doped CdTe PERC devices. To tackle this challenge, we develop robust nanofabrication and characterization platform to study CdTe PERC devices consisting of a patterned Al 2 O 3 layer on CdSe( 1-x )Te x (Cu-doped, GrV-doped; x = 0 to 1; CST). First Solar supplies high-quality CST materials. The dark and light I-Vs under 1-sun illumination are extracted for a series of each set of devices. We perform quantitative and qualitative PV analysis for a series of Cu-doped and Gr-V doped PERC devices, showing notably different V oc changes for GrV-doped compared to Cu-doped PERC devices. This project attempts to produce individual contacts on single grains and grain boundaries to measure lateral transport. As a model system, we use a CdSe( 1-x )Te x film on glass prepared by a colossal grain growth (CGG) technique at National Renewable Research Laboratories (NREL). Our preliminary results confirm that intergranular transport is hindered by the electrical barrier formed near grain boundaries. The PERC fabrication and the lateral transport measurement platform developed in this project can easily be applied to other types of advanced CdSe( 1-x )Te x architectures to better understand local photocarrier transport, in turn, providing the fundamental knowledge to improve the performance of CdTe PVs.
14 SOLAR ENERGY↗
Distinguishing bulk and surface recombination in CdTe thin films and solar cells using time-resolved terahertz and photoluminescence spectroscopies
Understanding the nature of recombination and its dependence on defects and interfaces is essential for engineering materials and contacts for higher open circuit voltage (V oc ) and power conversion efficiency in photovoltaic (PV) devices. Time-resolved photoluminescence (TRPL) has conventionally been used to evaluate recombination, but carrier redistribution often dominates the response at short times. In this work, we report on the quantification of carrier dynamics and recombination mechanisms by complementary use of both time-resolved terahertz spectroscopy (TRTS) and TRPL combined with numerical modeling of the continuity equations and Poisson’s equation. We have demonstrated this approach using CdTe thin films. A thin film stack with CdTe fabricated by vapor transport deposition and treated with CdCl 2 exhibited a bulk lifetime of 1.7 ± 0.1 ns, negligible CdTe/CdS interface recombination velocity, and back surface recombination velocity of 6.3 ± 1.3 x10 4 cm/s. In contrast, a film stack without CdCl 2 treatment had a bulk lifetime of only 68 ± 12 ps and a higher interface recombination velocity of 4 ± 2 x10 8 cm/s. By determining the locus and mechanisms of performance-limiting recombination, we can accelerate the development of thin-film PVs with higher V oc and efficiency. While the method has been demonstrated here using CdTe, it is also applicable to perovskites, Cu(InGa)Se 2 , Cu2ZnSn(S,Se) 4, and emerging technologies.
14 SOLAR ENERGY↗
First principles investigation of dopants and defect complexes in CdSe$_x$Te$_{1-x}$
Se alloying is a common approach to improve the performance of CdTe solar cells by tuning the bandgap, defect levels, and carrier density. A fundamental understanding of these improvements, specifically the effect of Se alloying on the behavior of defects and dopants in CdTe, remains unclear. Here, in this work, we present a density functional theory (DFT) study of point defect energetics in CdTe and CdSe x Te 1-x with x = 0.25, leading to a comparison of how native defects, dopants (As and Cu), impurities (Cl and O), and related defect complexes behave in CdTe vs CdSe x Te 1-x . Our calculations, performed by combining semi-local and nonlocal hybrid functionals, show a general lowering of the formation energies of native defects as well as substitutional defects formed by As and Cl upon Se addition. For successful p-type doping with As, destabilizing Cl-based defects in the CdSeTe lattice would be essential. We find evidence for some low-energy defect complexes of As, Cl, and O in CdSe 0.25 Te 0.75 . The computed defect formation energies further enable estimates of temperature-dependent defect concentrations and self-consistent Fermi levels. A comparison of defect energetics with the energies of impurity phases reveals that As, Cu, Cl, and O overwhelmingly prefer being segregated to unwanted As 2 O 5 , AsCl 3 , Cd 2 AsCl 2 , and CuO x phases rather than remain at defect sites, but such segregation is less likely to happen in CdSe 0.25 Te 0.75 than in CdTe. Overall, our work presents a list of likely defects and complexes in CdTe and Se-incorporated CdTe, paving the way to explain and mitigate limited dopant activation in experimental observations.
CdTe↗
Optoelectronic and material properties of solution-processed Earth-abundant Cu 2 BaSn(S, Se) 4 films for solar cell applications
Copper barium thioselenostannate, Cu 2 BaSnS 4-x Se x (CBTSSe), absorbers employ low-toxicity and abundant metals while offering low-cost manufacturing options, controllable stoichiometry and band gap tunability (from 2 eV at x = 0 to 1.55 eV at x = 3). CBTSSe can therefore be considered a prospective candidate for maintaining or improving upon the advantages of already commercialized Cu(In,Ga)(S,Se) 2 (CIGSSe) and CdTe absorbers. Here, we focus on solution-deposited stoichiometric CBTSSe films with band gap of 1.59 eV (x ≈ 3) and explore the fundamental film properties. Temperature- and excitation-dependent photoluminescence studies reveal a dominant defect emission at ~1.5 eV and a second deep defect feature at 1.15 eV. From time-resolved terahertz measurements, we find a charge carrier (electron and hole sum) mobility of ~140 cm 2 /Vs—i.e., comparable to values in CIGSSe or Cu 2 ZnSnS 4-x Se x (CZTSSe)—as well as a two-component minority carrier lifetime. A longer-lived lifetime component (~2 ns) arises from bulk recombination. However, strong recombination at the (bare) surface leads to a ~50 ps lifetime, inferior to state-of-the-art CIGSSe or CZTSSe absorbers. This recombination issue may worsen for CBTSSe/CdS interfaces, due to a cliff-like band alignment with 0.6 eV band offset, as revealed by ultraviolet photoemission spectroscopy. A low number of charge carriers within the absorber further contributes to a high series resistance. Employing these films, we also report the highest performance achieved from solution-processed trigonal CBTSSe thin-film photovoltaic devices, with open circuit voltage, short-circuit current density, fill factor and efficiency of 470 mV, 14.3 mA/cm 2 , 43.6% and 2.9%, respectively. The physical measurements provided on the stoichiometric solution-processed CBTSSe absorber further point to critical areas for future improvement of CBTSSe and related photovoltaic cells in the quest for higher efficiency devices based on earth abundant metals.
14 SOLAR ENERGY↗
Bifacial CdTe Solar Cells with Copper Chromium Oxide Back-Buffer Layer
Bifacial solar cells have the potential to maintain energy output higher than monofacial devices under unfavorable weather conditions. A transparent back-buffer layer which can passivate the interface and improve the minority carrier lifetime is critical in CdTe-based bifacial devices. Herein, solution-processed Cu x Cr y O z as a promising back-buffer for CdTe/CdS solar cells is demonstrated. The carrier lifetimes measured at the front and back of the device are 31.2 and 3.1 ns, respectively, which correspond to an increase of ≈38% and 138%, respectively, compared to the reference device. This dramatic improvement in lifetime results in a 100% increase in short-circuit current measured with backside illumination. The best bifacial device has efficiencies 7.6% and 12.5%, respectively, from back and front illumination, yielding a bifaciality factor of 0.60.
14 SOLAR ENERGY↗
Human Health Risk Assessment for Improper Landfill Disposal of End-of-Life CdTe Modules
The present work is a continuation of the 2020 IEA PVPS Task 12 Human Health Risk Assessment Methods for PV Part 3: Module Disposal Risks. The 2020 report performed a human health risk assessment (HHRA) for disposal of a cadmium telluride (CdTe) PV module in an unlined landfill, focusing solely on risks from cadmium. This study extends the 2020 HHRA on CdTe PV, analyzing eleven constituent elements: Cd, Se, Te, Cu, Si, Cr(III), Mo, Sn, Zn, Ni, and Al. The present HHRA was performed through two methods: utilization of the U.S. Environmental Protection Agency's (USEPA) Delisting Risk Assessment Software (DRAS V.4.0) on eight exposure pathways for cancer risk and non-cancer hazards; and comparison of exposure point concentrations to federal standards for groundwater, surface water, air, and soil exposure pathways. Cancer risks and non-cancer hazards posed by elemental leaching through all evaluated exposure pathways, using both methods, were found to be several orders of magnitude below USEPA health-protective thresholds. Cadmium exhibited both the highest risks and lowest uncertainty considering data availability on chemical content, leachate, and federal screening levels.
CdTe↗
Human Health Risk Assessment for Improper Landfill Disposal of End-of-Life CdTe PV
The present work is a continuation of the 2020 IEA PVPS Task 12 Human Health Risk Assessment Methods for PV Part 3: Module Disposal Risks. The 2020 report performed a human health risk assessment (HHRA) for disposal of a cadmium telluride (CdTe) PV module in an unlined landfill, focusing solely on risks from cadmium. This study extends the 2020 HHRA on CdTe PV, analyzing eleven constituent elements: Cd, Se, Te, Cu, Si, Cr(III), Mo, Sn, Zn, Ni, and Al. The present HHRA was performed through two methods: utilization of the U.S. Environmental Protection Agency's (USEPA) Delisting Risk Assessment Software (DRAS V.4.0) on eight exposure pathways for cancer risk and non-cancer hazards; and comparison of exposure point concentrations to federal standards for groundwater, surface water, air, and soil exposure pathways. Cancer risks and non-cancer hazards posed by elemental leaching through all evaluated exposure pathways, using both methods, were found to be several orders of magnitude below USEPA health-protective thresholds. Cadmium exhibited both the highest risks and lowest uncertainty considering data availability on chemical content, leachate, and federal screening levels.
chemicals↗
Enabling bifacial thin film devices by developing a back surface field using Cu x AlO y
Bifacial solar cells have the potential to increase the energy yield per unit area over traditional monofacial devices without significant added cost, driving $/kWh costs lower and accelerating the adoption of solar photovoltaics. However, the performance of bifacial thin film solar cells significantly lags that achieved by crystalline silicon cells. Here we incorporate wide bandgap Cu x AlO y as a back buffer layer for CdTe devices and achieve a backside illuminated device with high current density and high fill factor. Moreover, these values remain nearly constant even as the absorber layer thickness changes, indicating that a fully-depleted device is not required for efficient charge collection. We show that this response is indicative of a back surface field, albeit with a persistent high back surface recombination velocity. By managing electron reflection, we achieved a backside illumination conversion efficiency of 7.1% and bifaciality of 0.55 for a 3.3 µm CdTe device and 8.0% and 0.62 for a 2 µm device. Future improvements can be made by identifying and incorporating a passivation material that reduces the back surface recombination velocity.
36 MATERIALS SCIENCE↗
Arsenic Doping of Polycrystalline CdSeTe Devices for Microsecond Life-times with High Carrier Concentrations
We report seminal advances in fabrication and understanding of group V (As) doped thin-film polycrystalline CdTe-based solar cells. The devices are fabricated using a novel approach, by sublimating layers of CdSeTe and CdSeTe:As. This new method allowed us to achieve minority carrier lifetime of over 1 μs, carrier concentration of more than 5x1015 cc-1 and external radiative efficiency of over 2% in a device configuration. We find an increase in open-circuit voltage when comparing As-doped, Cu-doped and undoped devices. The choice of CdSeTe instead of a CdTe-only absorber has been explained using first-principle density functional theory model. A SCAPS device model is used to analyze the potential causes for lower open-circuit voltage.
14 SOLAR ENERGY↗
Computational design of passivants for CdTe grain boundaries
CdTe is the second most-widely deployed photovoltaic (PV) material due to its high efficiency and low manufacturing costs. Currently, polycrystalline CdTe (poly-CdTe) has a record efficiency of similar to 22%, which is still well below the theoretical limit (similar to 30%). Polycrystalline CdTe films that have incorporated Cl or Se show higher efficiency, possibly due to the segregation of these ions to the grain boundaries (GBs), where they may passivate the dangling bonds. However, the efficiency enhancement mechanisms of passivants in CdTe GBs, and the feasibility of employing alternative passivants, have not been well explored. Here, we present a systematic computational study of CdTe GBs with potential passivants, namely S, P, As, Se, and Sb on Te sites, and Na, Mg, Al, Sc, Cu, and Zn on Cd sites. Density functional theory (DFT) calculations were performed on GB dislocation core structures derived from scanning transmission electron microscopy (STEM) images of a model GB (bicrystal). We computed the segregation thermodynamics, electronic density of states, and charge variations near doped CdTe GBs. We find that segregation of impurities to GBs is thermodynamically favorable. For a Te-terminated core, Se, S, and P on Te sites effectively reduce midgap states. For both Cd-and Te-terminated dislocation cores, Sc and Al reduce midgap states when substituted for Cd atoms. Overall, the greatest improvement was achieved with co-doping, i.e. simultaneously substituting Te with Se and substituting Cd with Cu or Al. The elimination of midgap states is predicted to increase the photovoltaic efficiency of CdTe by reducing the recombination at grain boundaries.
14 SOLAR ENERGY↗
Arsenic Doping of Polycrystalline CdSeTe Devices for Microsecond Life-times with High Carrier Concentrations
We report seminal advances in fabrication and understanding of group V (As) doped thin-film polycrystalline CdTe-based solar cells. The devices are fabricated using a novel approach, by sublimating layers of CdSeTe and CdSeTe:As. This new method allowed us to achieve minority carrier lifetime of over 1 μs, carrier concentration of more than 5×l0 15 cc -1 and external radiative efficiency of over 2 % in a device configuration. We find an increase in open-circuit voltage when comparing As-doped, Cu-doped and undoped devices. The choice of CdSeTe instead of a CdTe-only absorber has been explained using first-principle density functional theory model. A SCAPS device model is used to analyze the potential causes for lower open-circuit voltage.
Munshi, Amit H.↗
A New Low-Temperature Approach for Efficient and Low-Cost Group V Doping in CdTe Thin Film Solar Cells (Final Technical Report)
The goal of this project is to develop a highly efficient low-temperature ex-situ Group V diffusion doping approach in the CdCl 2 treated polycrystalline CdTe film using the group V chlorides (i.e., PCl 3 , AsCl 3 , SbCl 3 , and BiCl 3 ) as dopants source. For the first time, our innovative doping strategies through the low-temperature ex-situ Group V doping process in polycrystalline CdSeTe successfully demonstrated a promising power conversion efficiency of ~19% compared to the Cu-doped counterparts. Our newly developed low-temperature ex-situ group V doping allows dedicated control of group V diffusion amount, generates a desirable depth profile, and is completely compatible with commercial CdTe module manufacturing. We built the partnership with the largest CdTe solar module manufacturing in the US, e.g., First Solar, Inc to further develop these low-temperature diffusion doped CdSeTe solar cells. Our technology was granted US Patent No. US11257977B2. In this project, we systematically investigate and characterize the new ex-situ group V doping mechanisms, defect chemistry, microstructure, and device physics in CdTe solar cells by combining experimental and theoretical means to pave the way to achieve lower cost toward $\$$0.02/kWh and higher power conversion efficiency (PCE) toward 25% in polycrystalline CdTe solar technology. This project will benefit the public by providing more affordable solar electricity and provide an effective way to address climate change.
14 SOLAR ENERGY↗
Photoluminescence of CdTe and CdZnTe compounds doped with 2% selenium
The addition of 2 % of selenium in CdTe and CdZnTe (CZT) exhibited an additional acceptor-bound exciton in photoluminescence (PL). From the PL and inductively coupled plasma mass spectrometer (ICP/MS) analyses, the additional acceptor-bound exciton emission is associated with a Cu impurity in the relatively low-purity (5N) precursor CdSe starting material. Additionally, thermal quenching of the acceptor/donor bound exciton emissions do not require a shift to any higher excited states or to the free exciton state. ICP/MS analysis also showed a higher concentration of Sn in CdZnTeSe (CZTS) compared to CdTe and CZT which is known to form a deep level trap at around E C – 0.83 eV. The trapping and de-trapping times indicate that the Sn-related deep trap acts as an electron trapping center. The relatively low electron mobility-lifetime product of CZTS might be correlated with the concentration of Sn in the impure CdSe material. Pulse height spectra using an Eu-152 gamma-ray source was taken for a 2-mm-thick planar CZTS detector. The spectra clearly showed all the expected gamma peaks with energy lower than 344.3 keV.
47 OTHER INSTRUMENTATION↗
Understanding Defect Activation and Kinetics in Next Generation CdTe Absorbers
This project investigated the role of defects and dopants in cadmium telluride (CdTe) solar cells to improve efficiency and long-term stability. Advanced X-ray microscopy and spectroscopy techniques were used to map composition, identify defect structures, and measure charge collection at the nanoscale. These experimental results were combined with computational modeling to understand how dopants such as copper and arsenic interact with other elements during processing. The study found that many dopants become electrically inactive due to the formation of complexes with chlorine and oxygen, limiting carrier concentration and device performance. It also showed that selenium, used to enhance efficiency, can migrate within the material during both manufacturing and operation, altering local structure and potentially affecting stability. The project developed new diagnostic and analysis tools for studying photovoltaic materials and provided a mechanistic understanding of key performance limitations. These insights support the development of more efficient, stable, and cost-effective CdTe solar technologies for large-scale energy deployment.
14 SOLAR ENERGY↗